RENOVATION OF MAIN ENTRANCE GATE DISPERSAL GATE AND WEATHERSHED ON MAIN GATE AT CGAE KOCHI

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided complete all as specified and as directed.

Demolition of brickwork or stone/boulders masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Material and labour for precast PCC 1:3:6 Type C1 using 20 mm graded aggregate solid block masonry exceeding 10 Cm width(with plain or interlocking joints as directed), built in cement mortar 1:6 all as specified and as directed.

Material and labour for precast PCC 1:3:6 using 20 mm graded aggregate solid block masonry not exceeding 10 Cm width(with plain or interlocking joints as directed), built in cement mortar 1:6 all as specified and as directed.

Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:4, finished even and fair without using extra cement complete all as specified and directed.

Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed.

Supply only integral water proofing compound all as specified and as directed.

Material and labour for for applying two or more coats of 100% premium acrylic emulsion paint having VOC not less than 50 gm/lit and UV resistance as per IS 15489-2004, dust, alkali and fungal resistant, of approved shadewith silicon additives @ 1.43 lit/10Sqm over a coat of primer @ 0.9Lit per 10 Sqm complete all as specified and as directed.

Material and Labour for preparing of new surfaces of any description and applying two coats of acrylic distemper, white or tinted over a coat of primer after applying one or more coat of wall putty to achieve smooth surfaces on plastered wall surface complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 M wide and n. exc 1.5 M depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 M wide and exc 1.5 M n. exc 3 M depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 3 m in depth and getting out in soft /loose soil complete all as specified and as directed.

Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete including necessary form work complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Material and Labour for TMT(CRS/HCR) bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for TMT bars(CRS/HCR), 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Removing waste materials, debris to a distance exceeding 1.5 Km but not exceeding 5.0 Km out side MD land including, loading, unloading and stacking at the destination complete all as specified and as directed

Material and labour for reinforced cement concrete design mix M-30 using 20 mm graded granite stone aggregate in foundaions including rafts, footings, foundaion beams, plinth beams, bases for columns etc, basement slabs, underreamed piles and mass concrete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately.

Material and Labour for reinforced cement concrete M30 design mix using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and as directed

Material and labour for reinforced cement concrete M-30 design mix using 20 mm graded stone aggregate as in as in beams, cantilever, lintels over 1.5M span etc complete all as specified and as directed.

Use and waste of formwork to sides of foundation footing, for rough finished surfaces, flat complete all as specified and as directed.

Use and waste for form work to sides of concrete surfaces of columns/pillars, square or rectangular in plan, rough finshed surfaces all as specified and as directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams to rough finished surface of concrete for flat complete all as specified and as directed.

Material and Labour for Granite 20mm thick ( of any type table rubbed and polished) work machine cut as in steps, jambs pillars,window cills, cooking platforms and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of granite and laid over and including 15mm thick cement mortar 1 :4 complete all as specified and directed.

Supply and fix Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde-E-250) quality-B as in bracing members etc complete including necessary cutting , welding in any shape and in any position / direction in hangar doors etc complete all as specfified and as directed by the Engineer-in-Charge.

Supply and fix mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with rivetted or bolted or welded attachment all as specified and as directed.

Supply and fix rolled mild steel in Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410W(Gde E-250) quality A complete all as specified and as directed.

Supply and fix mild steel bolts (Machine made) made with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 10 cm and not exceeding 15 cm and dia 11 to 15 mm complete all as specified and as directed.

Supply and fix Mild steel flat iron section as in wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply and fix structural steel work in tubular trusses including special shaped washer complete using ERW or induction butt welded tubes conforming to IS - 1161-1979 grade St.-240 all as specified and as directed.

Material and labour for preparation of new or previously untreated steel surface over 10 cm width or girth and applying two coats of synthentic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fix Welded steel wire fabric Weight exceeding 3.5kg but not exceeding 4 Kg per square metre with dia of wire not less than 3.8mm , fixed to wood or steel members complete all as specified and as directed.

Supply and fixing Pre- painted galvalume aluminum zinc coated corrugated sheet (manglore patern) of 0.50mm thickness having tensile strength of 550 Mpa with coating thickness fixed with GI self taping screws as in roof covering/cladding to wall, ridges, valley gutters fixed to frame work all as per manufacturers instructions all as specified and as directed.

Supply and fixing Pre- painted galvalume aluminum zinc coated plain sheet 0.5mm thick having tensile strength of 550 Mpa with coating thickness prepainted plain galvalume sheeting as in ridge and cladding, fixed with GI self tapping screw complete all as specified and as directed.

Supply and fix Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including necessary hangers 6mm dia GI up to1200mm length adjusting level fixed to roof slab by means of cleats made out of FI 40x3mm size 60 cm long and expansion holdfast 12.5mm dia 40mm long with and including PVC profile ceiling of surface laminated any pattern and any shade of 7 to 10 mm thickness and any colour completely all as specified and as directed.

Providing and fixing Powder coated Aluminium work for doors and Partitions walls with extruded built up standard tubular sections/ appropriate & sections and other sections of approved make fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners for fixing of vertical sections in the ceiling to support the frame including necessary filling up of gaps at junctions, top, bottom and sides with required PVC/ neoprene felt, etc. Aluminium sections shall be smooth, rust free straight, metered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass/ stainless steel screws all complete the direction of engineer-in-charge With powder coated aluminium section of 63.5mm X38.10mm ( sectional weight of the Aluminium section should not be less than 4 Kg. for the sectional length of 15) with 12 mm thick both side pre-laminated flat pressed three layer of graded wood particle board conforming to IS: 12823 grade I type II in panelling of partition walls or with float glass panes of 5 mm thickness ( Modi, saint Gobain or equivalent) panelling of required height complete in all respect including all hardware fittings as per the direction of Engineer -in charge

Supply and fix powder coated aluminium door and partition frame, Partition using standard aluminium section one or more rebates with joint clip and using rubber beading etc complete all as specified and directed. Note : Glass panel/particle board panel filling shall be measured and paid separately.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window ( two shutters glazed & one shutter wire gauge) with frame, glazed with 5 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing of Member for wire gauge Section shall be 18.00 x 25.00 x 1.35 (Section No 20791). position, concelled type lock for all three shutter, PVC roller etc all as specified below, including taking down old window and making good jambs, cill, ceiling with 10mm thick plaster in CM (1:4) and applying two coat of Oil bound distumper over a coat of wall care putty complete all as specified and directed including taking down old unservicable one (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.20 mm ( Section No 21447) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.20 mm ( Section No 21446) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.19 (Section No 21455) (d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.19 (Section No 21454) (e) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.29 (Section No 20844). Make Jindal/Hindalco/Nalco

Supply and Fix in repairs 125mm hasp and staples,aluminium anodized including bolt to hinges plate and fixed with screws complete all as specified and directed.

Supply and fix in repairs aluminium handles fabricated type anodised of size 100mm complete all as specified and as directed.

Supply and fix in repair 100mm long butt hinges medium weight mild steel cold rolled complete all as specified and as directed.

Supply and Fix in repair 150mm long aluminium anodised barrel tower bolt all as specified and as directed by Eng-in-charge.

Supply and fix in repairs door closer hydraulically regulated cast iron body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and as directed.

Material and labour for roof tiles, Mangalore pattern, interlocking at side laid dry including applying One coats of weather proof antifungal exterior emulsion paint applied to surface of roof tiles complete all as specified and as directed.

Material and labour for Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in CM 1:6 including applying One coats of weather proof antifungal exterior emulsion paint applied to surface of roof tiles complete all as specified and as directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ as in parapets/hand railing etc on walls, beams and colums in floors, roofs, landing, balconies, canopies, deck slab and in shelves, as directed including use of form work as necessary all as specified and as directed.

Material and Labour for Vitrified tiles 10mm thick (square/rectangular) light coloured, area of each tile exceeding 0.42 sqm and not exceeding 1.0 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed of 15mm thick in CM 1:6 complete all as specified and as directed.

Material and Labour for non-skid coloured Ceramic tiles 7 to 8mm thick (square/rectangular)area of each tiles exceeding 0.11 Sqm but not exceeding 0.18sqm as on floors and jointed in neat cement slurry and in coloured cement to match, fixed over and including provision of screed bed/ bedding layer/backing coat of 15mm thick in CM 1:6 complete all as specified and directed.

Supply and fix stainless steel letters of 300mm height and proportionate width fixed on vertical surfaces of hight 12 to 15m complete all as specified and as directed.

Material and labour for painting lines, dashes, paintings, letters etc on on steel surfaces not exceeding 10 cm wide with with synthetic reflectieve paint over a coat of primer including preparation of old treated surface all as specified and as directed.

Supply and fix Indian coast guard emblem / symbol of composite panel material of any shap and fixing of retro reflective sheet 1.5mm thick white or colour over ACP sheet and fixing the Vinyl stickering of required emblem, legeneds, letters,numbers etc., shall be processed and finished with materials and in a manner specified by the sheeting manufacturer. The colour and Contents shall be approved by Engineer in charge complete all specified and directed by Engr-in-charge.

Providing and fixing 0.71 mm thick aluminium alloy colour coated roofing sheets of alloy IS designation 31500, temper H*8 conforming to IS 737 and dimension as per IS Code 2676 with characteristics of good formability and corrosion resistance and troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000mm at all heights, levels and locations. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/ tapping stainless steel screws M6, 60 mm long with 3 mm EPDM seal washer etc, all inclusive of labour, scaffolding, T&P and sundries etc.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) remaining serviceable tiles to stores and rubish off the premises all as specified and as directed.

Material and labour for machine pressed precast concrete interlocking paver block, any shape and size of 80mm thickness M-40 grade conforming to IS 15658-2006 with grey cement and pigment laid over and including 50mm thick 6.3mm aggregate cushioning, compacted with mechanical surface vibrator and with scratch proof lacquer coating on top surfaces complete all as specified and directed.

Relaying/ refixing the usable interlocking paver block obtained from dismantling after levelling sunken portions with required thickness of sand/stone chipping cushioning and levelling the top surface to match with existing surfaces, all as specified and as directed. NOTE: The rate quated is inclusieve of Crushed sand/stone chipping required for levelling, nothing extra shall be paid on this account.

Material and labour for plain cement concret 1:3:6 type C-2, 75mm thickness using 40 mm graded stone aggregate as in sub bases and pavings complete all as specified and directed.

Material and Labour for preperation of old decorated MP Tiled surfaces of roofs, Chajjas etc by washing, rubbing downand stopping of painted surfaces and applying one coat of anti fungal paint(Terracotta coloured) premium quality, applied to surfaces of up to 4 storied buldings. complete all as specified and as directed.

Material and labour for preparation of old steel surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

Supply and fix 1.25mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Material and Labour for point wiring complete using 1.5 Sqmm PVC insulated unsheathed copper conductor, stranded cable (FRLS) upto and including working voltage 1100volts grade, drawn through and including PVC casing and caping including all accessories ISI marked including press fit white PVC open switch/surface board high strength and crack resistance and unsheathed copper conductor stranded cable(FRLS) earth continuity wire connected to DBs/sunken boxes/fittings of size 1.5 Sqmm Cross sectional area and all other metal parts with earth dolly for the following:-. (a ) one light point controlled by one switch 5 Amps

(b ) one fan point point controlled by one switch 5 Amps

(c) One 3 pin socket outlet 5 Amps on Independent board

Supply and fix Modular switch one way 6A, 1 Module complete all as specified and as directed.

Supply only Modular socket outlet, 6 Amps, 2 and 3 pin combined complete all as specified and directed.

Supply and fix ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep min air delivery 210 CFM service value 6.00 BEE. Five Star rated with brushless direc current motor (BLDC) complete all as specified and as directed.

Supply only LED luminaire 600 mm x 600 mm,40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make: Bajaj/Havells/ CG

Supply and fix Ceiling rose in poly carbonate 3 plates flush type 6 Amps, 230 volts AC complete all as specified and directed.

Supply and fix MCB SP 6-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole in the MCB DB,IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including suitable size copper Lugs complete all as specified and directed.

Supply and fix MCB SPN 40 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fix in repairs Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 8 way with 200 Amps rated copper bus bar double door protection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer flush to wall complete all as specified and as directed.

Material and labour for Sub main wiring using two runs of single core PVC insulated cable (FR) 6 sqmm copper conductor multi stranded and one run of 6 sqmm copper conductor insulated cable (FR)using as earth wire drawn through and including suitable size non metallic rigid PVC conduit not less than 25mm dia with accessories including taking down old aluminium/Copper Sub main wirng complete all as specified and directed. Note- 3 run of 6 sq mm PVC copper wire and One run of PVC conduit shall be measured and paid as one unit.

Earthing with Galvanized steel earth plate electrode of size 600mmX600mm, 6.00 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below the normal ground level with top edge of the plate not less than 1.5m below normal GL and connected to galvanized iron strip of size 32 x 6 mm size by means of bolts, nuts, check nuts and washers of galvanized iron steel all as shown in Electrical Plate No.5 connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1:2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 100mm c/c in both ways, including necessary form work complete including necessry test on completion including taking out old earthing all as specified and as directed. Note : The unit rate shall also include for excavation, earth work in hard/dense soil PCC (1:3:6) type C1 pit, RCC cover slab, GI funnel with 40 mm dia watering pipe, wire mesh, 15mm dia light grade GI protection pipe for earth lead etc., complete

Supply and fix LED flood light fitting 70W energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP65/66, 10KV SPD, more than 100lm/watt flood light with high power LEDs as light source, suitable for highlighting architectural facade highmast and general purpose lighting complete all as specified and as directed. Make: Havells/Crompton Greaves/Philips.

Supply, laying or passing through pipe LT, XLPE insulated, galvanised steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor 1100 Volts grade of size 10 Sqmm 4 core including connecting/testing after taking out from trenches/ pole unserviceable LT UG cable complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 meter in depth for taking out and laying UG cable and getting out, excavated earth, forming bottom surfaces to required level complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soil complete all as specified and as directed.

Removing excavated soil and depositing to the sides and returning filling in including spreading leveling watering and well ramming in layers n.exc 25cm thick in soft/loose soil after cable is laid complete all as specified.

M&L for providing dry screened river sand as in sand cushioning to under ground cable including punning down of sand by layer complete all as specified and as directed. NOTE: Punned thickness shall be measured and paid.

Supply and lay unreinforced precast cable cover size 250X150X40 mm LV1 complete all as specified and as directed.

Schedule of Credit (Minus) Rs.30866.00 NOTE: Bidder shall insert credit amount of Rs. 30866.00 as rate in Green field under Col-13.

HIRA FACILITY (BID ID -3260625)