PR.NO. 235/2022-23 MCF New shed construction in Triprangode GP

Amount

Providing shed for MCF

50.6.1.2:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

OD418335/2022-2023:1.002-Specification code: OD48177/2022-2023Providing and fixing M.S. sheet door including frame using MS angle, flat and MS sheet, all necessary fittings complete, including applying a priming coat of approved steel primer, all materials and labour charges etc. complete. Details of cost for one single leaf door size 1.00 x2.10 m = 2.10 sqm. . MATERIAL: (i) Door frame 40*40*6 mm angle=2(2.10+0.99)+10% wastage = 6.80m @ 3.5 kg/m=23.8 kg ii) Shutter frame 35*35*5 mm angle= 2(2.05+0.98)+10% wastage= 6.67 [email protected]/m=17.34 kg iii) MS flat 25*5mm= 4*0.98+10% wastage= 4.31m @1 kg/m = 4.31 kg iv) M.S. sheet Imm thick 0.98* 2.04= 2.00+10% wastage = 2.20 sqm. @ 7.85kg/sqm. = 17.27kg. Add 2.00 kf for hinges, Aldrop, tower bolt etc Total = 23.8+17.34+4.31+17.27+2.00 = 64.72 kg = 0.647 q Excluding wastage =59.01 kg Area of steel primer = 1.00*2.1*2.25 =4.73m2

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

10.25.1:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete

OD432667/2022-2023:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 meter or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

mohammed siraj kk

Bidder Name

T. BALAN

mohammed siraj kk