Construction of Multi storied (G Plus 5) Lakhipur Sub Divisional office cum Administrative Complex at Lakhipur in Cachar District

Amount

EARTH WORK Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil (For Side Drain)

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

ANTI TERMITE TREATMENT Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Earth work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil All kinds of soil

13 Passenger Lift with power operated centre opening doors and AC variable voltage & variable frequency controls.

Supplying , installtion , testing and commissioning of STP / ETP of approprite technology including civil work ( except plant room) , tertiary treatment etc . For the Building / campus ( size 75 KLD )

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) PCC FLOOR BASE

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) FOR SIDE DRAIN

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone -III): 4 graded stone aggregate 12.5 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. 1:1.5:3 ( 1 Cement : 1.5 Coarse sand : 3 Aggregate )

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All work upto plinth level FOR BUILDING

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All work above plinth level upto floor V level FOR BUILDING

Centering and shuttering including strutting, propping etc. and removal of form for Foundations,footings,bases of columns including beams etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, pillars, piers, abutments, posts and struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Steel Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe 500 D or more

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: In proportion 1:5

20 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement : 4 fine sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

In Side Drain Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). Red sand stone - 30mm thick gang saw cut stone

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin- charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid).

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S.Grill of required pattern in frames of windows etc. with M.S.flatsand Sq. or round bars ect. Including priming coate with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer hanging, brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS- 1868 ) transparent or dyed to required colour or shade with necessary screws etc complete. 300 x 10 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS- 1868 ) transparent or dyed to required colour or shade with necessary screws etc complete. 250 10 mm

Providing and fixing ISI marked aluminium handles anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc complete.

Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. 'Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath &courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 1000x1000 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 800 x800 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20 mm nominal size stone aggregate )

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 withcharacteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.56 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. 110 mm Dia Coupler

Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. Bend 87.5° 110 mm bend

Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM seal and SS plain washer complete : Precoated/mill finish aluminium Ridges plain (500- 600mm)

CEMENT PLASTER (IN COARSE SAND) 20 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 12 mm cement plaster

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Varnishing with varnish of approved brand and manufacture One or more coats with spar varnish

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR Value-25

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 80 mm nominal inner dia. Pipes.

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore Vertical

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). 500 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Single pile upto 50 tonne Safe capacity Routine test (Test Load 1.5 times the Safe capacity)

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade II (glass fibre base self finished bitumen felt) and sixth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface but excluding grading, complete.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels including: The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding , other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runnerwith suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part Iand laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 80 mm nominal inner dia. Pipes.

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore Vertical

Providing , Fitting and fixing centrifugal pump of horizontal split type, CI body MS shaft bronze impeller of approved make with 3 phase TEFC electric motor on common base plate Output 2000lts/hr against total head of 25 m

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through Sieve of I.S. designation 4.75mm

Rough dressing the trenched ground including breaking clods.

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately)

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 90 cm dia, and 90 cm deep

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 60 cm dia, and 60 cm deep

Providing and watering of irrigation water through water tanker of Horticulture features i.e. lawn, tree, shrubs, hedge/edge, ground cover etc. at the site of work. Water tanker having 5000 lit. capacity with one labour for watering i/c cost of water, filling of tanker, wartering at site with all leads and lifts as per direction of officer-in-charge.

Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.

Providing and applying anti termite treatment of infected trees i/c all branches/leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Trees Plant

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Shrub Plant

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) Hedge/Ground cover Plant

Providing and fixing of Tuflex Garden fencing Hexagonal net/or equivalent of green colour having contents ( Weight grams/sqm. 510 (+/- 8%)) in width of 60 cm. with bamboo of 90 cm. length. The bamboo should be painted with green colour paint of approved brand and manufacture (two or more coats) and fixed 30 cm. below ground level and 60 cm. above ground level at a distance of 1.50 mtrs. The net and bamboo should be binded with 2 mm. G.I. Wire at three places properly as per direction of Engineer-in-charge.

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge

Providing and stacking of Pterospermum acerifolium (Kanak Champa) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tabebuia sp. of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 60-90 cm, with 8-10 branches, and healthy foliage, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Nerium oleander variegated of height 60-75 cm., multibranched in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.

Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan), including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m,as per directions of Engineer in Incharge. All kinds of soil

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm with wall thickness of 25.4 mm

Providing and displaying of Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliage in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Raphis Palm having ht. 75 cm to 90 cm with 15 to 18 equal suckers, well developed, full of fresh and healthy leaves from bottom to top in 35 cm PVC Pots/C.Pots & as per direction of the officer-in-charge.

Providing and displaying of Seaforthia Palm having ht. 1.50 m to 1.80 m with 12-15 suckers, well developed, fresh and healthy lush green leaves from bottom to top in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Coleus broad leaves having 3 to 4 branches equal well developed with fresh & healthy foliage in different colour in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Gazania hybrid in different colour well developed with fresh & healthy foliage with full bloom in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing & Fixing, testing and commissioning of brass stop cock of approved quality with cp wall flange, nut and washer etc. of approved brand for cistern, health faucet and Geyser including cutting and making good the walls wherever required.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

Providing and fixing medium duty S.S. Floor grating with frame of approved design brand including setting in floor with cement motor to match with floor finish as per architect requirement including cutting and making good floor or wall wherever required. a) 125mm dia

Providing, fixing, testing and commissioning of CP Brass Health Faucet with nuts, washers of approved brand including cutting and making good the walls wherever required. Rate of flow should be 4 LPM

Providing, fixing, testing and commissioning of CP Brass toilet paper holder with nuts and washer of approved brand including cutting and making good the walls wherever required.

Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required

Providing, fixing, testing and commissioning of CP Brass coat hook of with nuts and washer of approved brand including cutting and making good the walls wherever required as directed by Engineering Incharge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

P/Fixing, testing and commissioning of 32 mm dia CP brass waste coupling of approved brand as directed by Engineering Incharge.

Providing & fixing, testing and commissioning of 32 mm dia CP brass Bottle Trap and pipe to wall with cp brass flange and rubber adopterfor waste connection for wash basin of approved brand including cutting and making good the wall/floor wherever required.

Providing & Fixing, testing and commissioning of brass stop cock of approved quality with cp wall flange, nut and washer etc. of approved brand for cistern, health faucet and Geyser including cutting and making good the walls wherever required.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing & fixing, testing and commissioning of counter mounted C.P. brass pillar tap for Sink of approved brand including cutting and making good the wall/floor wherever required.

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing, fixing, testing and commissioning of white vitreous china large urinal partition with concealed CI bracket, cutting and making good as required.

Fixing, testing and commissioning of vertical, free and standing, water cooler, 150 litre per hour cooling and storage capacity, with stainless steel tank, SS panels, PUF insulation, gravity saled faucet with zero leakage, hermatic compressor, condenser with fan, thermostat,two cold water outlets, suitable for operation on 230V+ 10%, 50 cycles single phase supply along with 3 KVA automatic voltage stabiliser wiring, foundation as required, including 'Eureka Forbes' make Aquaguard, Hi-flo model with flow rate of 3 litres/ minute.

Providing, Fixing, testing and commissioning of Concealed type Stop valve 20mm dia including nuts, bolts and washers of approved brand including cutting and making good the walls wherever required.

Providing, Fixing, testing and commissioning of Concealed type Stop valve 32mm dia including nuts, bolts and washers of approved brand including cutting and making good the walls wherever required.

Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-A cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, clean out plug, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required FOR RAIN WATER SYSTEM a) 110 mm O.D type "A"

Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-A cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, clean out plug, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required FOR RAIN WATER SYSTEM b) 200 mm O.D type "A"

Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-B cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required FOR SOIL, WASTE AND VENT SYSTEMS a)110 mm O.D type "B"

Providing, fixing, testing and commissioning of uPVC SWR pipe confirming to IS-13592, Type-B cut to required lengths including all necessary fittings and special such as bends, junctions offset, access pieces (plain or door), Tees, bends, reducers, flanges, plugs unions and clamps Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly epoxy coated including chasing, cutting and making good the walls / floor etc. wherever required FOR SOIL, WASTE AND VENT SYSTEMS b)150 mm O.D type "B"

Providing and fixing, jointing, testing and commissioning of uPVC pipe schedule 40 (for waste drainage of wash basin and kitchen sink etc.) cut to required lengths including all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door). Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly paint epoxy coated. a) 32 mm

Providing and fixing, jointing, testing and commissioning of uPVC pipe schedule 40 (for waste drainage of wash basin and kitchen sink etc.) cut to required lengths including all necessary fittings and specials such as bends, junctions offsets, access pieces (plain or door). Fixing at wall / ceiling level supported by G.I. clamps, hangers etc. duly paint epoxy coated. b) 40 mm

Providing and fixing uPVC cowl complete including cutting and making good the walls and floors wherever required. a) 110 od

Providing and fixing uPVC cowl complete including cutting and making good the walls and floors wherever required. b) 150 od

Providing & fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size,drilling,welding fixing and welding to insert plates in RCC structural members as directed by engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.) (Gratings over drain).

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) a) 15 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) b) 20 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) c) 25 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) d) 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) e) 40 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) f) 50 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) g) 65 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) h) 80 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (Domestic & Flushing water supply pipes from OHT, in shaft,terrace, internal pipes in ceiling and concealed in wall, etc) i) 100 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore.

Effecting disinfections of water lines including overhead water tanks with Bleaching Powder as directed by the Project-in-Charge.

Providing, fixing , testing and commissioning threaded / flanged water meter with direct reading dial in KL with all necessary fitting such as threaded pieces, unions pressure gauge, isolation cock, flanges piece for future removal, flanges / unions complete with all necessary testing charges and obtaining test certificates from municipal authorities, on following size pipe lines (1 no. strainer shall be provided at inlet and cost shall be inclusive for the same).

Effecting connection from Existing/ Municipal Water Supply line including necessary excavation & making good the same including cutting, boring and tapping the Existing line by providing and installing ferrule / Tee connections with necessary fittings as required and making good the same. The rate for this item also includes complete services from the contractor for liasoning works such as filing necessary applications, submission of forms for approval to the municipal authorities, depositing the fees / other amounts as required for getting the premises / installations, inspected and approved and all other formalities required till the water connection is obtained. All the expenses incurred in this regard shall be borne by the Contractor except for the official payments to be made for any security deposit etc. which will be reimbursed on production of original voucher.

Providing, laying, jointing and testing in position DWC HDPE pipes conforming to IS:16098 (Part 2): 2013 (SN-8) and suitable for the respective working pressures with all fittings and specials,e.g.couplings, tees, bends, reducers, end plugs etc., jointing by fusion welding method as per manufacturers recommendations all complete including excavation in all kind of soil and mooram filling. (Sewerage Lines) b) 300 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : a) 100 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : b) 150 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : b) 250 mm dia

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : b) 300 mm dia

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : a) Inside size 45 x 45 cm and depth up to 60 cm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : b) Inside size 90 x 90 cm and depth up to 75 cm

c) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : a) Inside size 45 x 45 cm and depth up to 60 cm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : b) Inside size 90 x 90 cm and depth up to 75 cm

[Domestic Water Transfer Pumps from UGT to OHT : Supply, installation, testing and commissioning of Vertical Inline Split Coupled (with rigid aluminium alloy coupling between pump shaft and motor shaft) single stage centrifugal pump each capable of delivering the specified flow rate comprising the following and complete as per specifications. Casing (Volute) - Cast Iron (BS 1452 Grade 220) - PN 16 Impeller - Gunmetal Bronze (BS1400LG2C) - Statically and Dynamically Balanced Casing Gasket - Confined Non Asbestos Fiber Pump Shaft - SS (BS970 416) Flush Line - Braided Stainless Steel Mechanical Seal - Outside Balanced (the pump design shall met the requirement of servicing / changing the mechanical seal without disturbing the pump shaft alignment) Motor Type - TEFC Squirrel Cage, Efficiency Class - IE3, Insulation - Class F, 415V ± 10% , 50Hz ± 5%, 3Ø AC Power Supply (1 Working + 1 Standby) Capacity : 30 Cum/hr Head : 35 M RPM : 2900

Supplying, fixing, jointing and testing in position the following medium grade (Class B) GI pipes for pump room, confirming to IS:1239 cut to required lengths including all necessary fittings of equal class (all fittings shall confirm to IS:1879 - part 1 to 10) and specials such as bends, tees, unions, reducers, flanges & plugs etc including standard specials as required, supporting laid on PCC 1:3:6 pedestals as directed, clamping it with necessary MS brackets and MS brackets for wall/ceiling support, including painting the pipes with two coats of enamel epoxy coated paints (in specific colour code) over two coat of specified primer, making necessary holes in walls, slab etc. and making good the same including testing the pipes to 10.54 kg/sq.cm after installation. Cutting hole in wall and making good the same as required. a) 65 mm dia

Providing and fixing gun metal non- return valve of approved quality (screwed end) :A) 200 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore.

Providing and fixing C.I. Y type Strainer including washer, nuts, bolts, 1.5 mm thick compressed asbestos gasket companion flanges as per table "E" complete. a) 200 mm dia

Providing and fixing M.S. galvanised puddle flanges (exact as per drawing) fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be hot dipped galvanised. for UGR . a) 25 mm dia

Providing and fixing M.S. galvanised puddle flanges (exact as per drawing) fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be hot dipped galvanised. for UGR . c) 50 mm dia

Providing and fixing M.S. galvanised puddle flanges (exact as per drawing) fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be hot dipped galvanised. for UGR . d) 65 mm dia

Providing and fixing M.S. galvanised puddle flanges (exact as per drawing) fabricated out of 6 mm thick M.S. plate of size 200 x 200mm plus dia of pipe of 600 mm long pipe pieces to R.C.C. water tanks / R.C.C. walls. The entire fitting shall be hot dipped galvanised. for UGR . e)100 mm dia

Providing and fixing 600 x 600 mm dia heavy duty sfrc/rcpc man hole cover for Under Ground domestic and fire water tanks as directed by Engineering Incharge

Providing and fixing PVC Foot Rest for UGR

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 haracter/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of addressable phone control module complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installing, testing and commissioning of 2 mm thick GI trunking with cover of the following sizes complete with angle iron supports/hanging arrangement etc. 25 x 150 x 25 in riser

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 2850 lpm at 56 m Head

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2850 lpm at 56 m Head

Providing & fixing MS Class ‘C’ 200 mm dia diesel engine exhaust pipe (including all fittings, clamps, steel support) for the engine. The pipe shall be provided with 12 mm thick supercera ceramic fibre rope.

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 70 m Head

Supply,Fabricating, fixing, testing and commissioning of air cushion tank (material IS 2062/2002) with SS air-release valve of approved quality with S.S isolation valve, GM drain valve, gate valve, provision for pressure switches, pressure gauge etc.inside the pump house including making inlet and outlet connection with MS pipe of required length from discharge header to air cushion tank, fixing properly and securing the same to the base etc. complete in all respect having painting including two coats of approved paint over a coat of primer. The tank shall be fabricated out of 8mm thick MS sheet shall be of cylindrical shape with 300mm dia and 1.5m height. The tank shall be installed on suitable vertical legs having M.S. plate of size 75mm x 75mm x 5mm at the bottom. The legs shall be grouted in Cement concrete foundation. Flange connection shall be provided for connection with discharge header. The tank shall be tested at 25 kg/sq.cm before installation.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : b) 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : d) 150 mm dia

Providing & fixing double flanged flexicon rubber expansion (bellows) joint with unit control of standard length as per maufacturers specifications suitable for working pressure of 15Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required for suction and delivery of pumps. b) 150 NB

Providing & fixing double flanged flexicon rubber expansion (bellows) joint with unit control of standard length as per maufacturers specifications suitable for working pressure of 15Kg/Sqcm including rubber gaskets, flanges, nuts, bolts and washers complete as required for suction and delivery of pumps. c) 80 NB

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

V- FIRE PANEL & ACESSORIES: Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

L.T.Cables Supply, installation, testing and commissioning of following sizes of PVC sheathed XLPE insulated Aluminium Copper conductor/ power/control armoured cables of 1100V grade on surface of wall or in existing cable trays with fixing hardware etc. as required. Aluminium Conductor armoured cables: 3.5 x 120 Sq mm

L.T.Cables Supply, installation, testing and commissioning of following sizes of PVC sheathed XLPE insulated Aluminium Copper conductor/ power/control armoured cables of 1100V grade on surface of wall or in existing cable trays with fixing hardware etc. as required. Aluminium Conductor armoured cables: 3.5 x 50 Sq mm

L.T.Cables Supply, installation, testing and commissioning of following sizes of PVC sheathed XLPE insulated Aluminium Copper conductor/ power/control armoured cables of 1100V grade on surface of wall or in existing cable trays with fixing hardware etc. as required. Aluminium Conductor armoured cables: 4 C x 6 Sq.mm

L.T.Cables Supply, installation, testing and commissioning of following sizes of PVC sheathed XLPE insulated Aluminium Copper conductor/ power/control armoured cables of 1100V grade on surface of wall or in existing cable trays with fixing hardware etc. as required. Aluminium Conductor armoured cables: 4 C x 4 Sq.mm

L.T.Cables Supply, installation, testing and commissioning of following sizes of PVC sheathed XLPE insulated Aluminium Copper conductor/ power/control armoured cables of 1100V grade on surface of wall or in existing cable trays with fixing hardware etc. as required. Aluminium Conductor armoured cables: 4 C x 2.5 Sq.mm

EARTHING Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For Wet riser System 25 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For Wet riser System 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : For Wet riser System 150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gun metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m

Providing and placing in proper position Weather proof hose cabinets for internal hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.6mx0.6 mx 0.45 m).

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing and placing in proper position Air release valve complete with 25 mm dia. brass air valve (ball valve, pressure gauge type), 25 mm dia brass stop cock, nipple, tees, B46 elbow, pipe and all accessories as required including fixing brackets.

Providing & fixing ABC type (Dry powder type ) extinguishers. Including all accessories as per IS specification (IS :15683) Consisting of welded MS cylindrical body with discharge hose ,discharge valve ,suspension brackets,initial filling etc. complete as required., initial filling etc complete as required. Capacity - 6 kg

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Providing and placing in Weather proof hose cabinets for external yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.6mx0.6 mx 0.45 m).

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia FOR RING MAIN

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

Providing and fixing RCC Hume Pipe NP 3 as per IS: 458 (For Road Crossing) 300 mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 25 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 32 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 40 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 50 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 65 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 80 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 100 mm dia

SPRINKLER & PIPING WITH ACCESSORIES Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : Welding of any kind on the galvanised support / hanger shall not be permitted. NOTE: FITTINGS UP TO 50 MM DIA MUST BE MS FORCED HEAVY DUTY SOCKET WELDED. ABOVE 50 MM DIA MUST BE HEAVY DUTY BUT WELDED FITTINGS. 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

Supply,Providing, fixing, testing & commissioning of SS spring loaded air relief valve for pressure of 16 kg/sqm of approved quality with gm isolation valve, tapers, G.I. pipes and specials etc. including making necessary screwed/ flanged joints by providing all jointing materials including painting and testing the joints to hydraulic pressures specified for pipes all complete as per drawings and as directed by the Engineer-in-Charge. a) 25 mm dia

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright Sprinkler

Providing & fixing brass quartzoid sprinklers (UL, FM approved) of 20 mm dia size, suitable for sustaining the 175 psi pressure on the seat & water hammer effect. The type & temperature rating shall be as follows : ii) Pendent type (79 deg.C) quick response sprinkler for kitchen area, K-80

SS Flexible braided pipe for below false ceiling sprinkler (ul / fm approved) 800/1000 MM LENGTH (OPTIONAL)

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 12 Module (200mmX150mm)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 8 way (4 + 24), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 12 way (4 + 36), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2+8 way,double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2+6 way,double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2+12 way,double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A Double pole mcb Isolator

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A Four pole isolator

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A Four pole isolator

Supplying and fixing MCCB SS enclosure with IP- 20/30 protection, pwder coated provision for housing Four pole (4P) MCCB, concealed in wall after cutting the wall & mending good the damages to original finish / on flat iron frame incl. painting, connection & provision for earthing attachment

Supplying and fixing 415 V Four Pole MCCB of Breaking capacity 25kA/35kA with fixed thermal and fixed magnetic / adjustable thermal and fixed magnetic setting in existing DBs / enclosure and necessary connection with rotary handle.(UPS I/C AND O/G) 125A FP MCCB

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 25A

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 40 A

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 63 A

Supplying and fixing 415V, TPN SFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating, at angle iron frame.(METER MAIN SWITCH)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 core x 6.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 6.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 10.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 16.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core x 25.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core x 50.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core x 120 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 core x 240 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 1 core x 50.0 sq. mm. XLPE, CU.armoured cable.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but with charcoal/ coke and salt ) as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 450 mm width X 50 mm depth X 1.6 mm thickness

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 4 core x 6.0 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 4 core x 10.0 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 4 core x 16.0 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 3.5 core x 25.0 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 3.5 core x 50.0 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 3.5 core x 70 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 3.5 core x 120 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 3.5 core x 240 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed aluminium conductor armoured cables as per specification. 3 core x 6 sq. mm. XLPE, Al.armoured cable.

Supplying of following 1100 volt grade XLPE insulated PVC inner sheathed and FRLS PVC outer sheathed Copper conductor armoured/Flexible cables as per specification. 1 core x50 sq. mm. XLPE CU. Flexible cable.

80 KVA ON LINE UPS with 15 min battery backup of 1 phase input & 1 phase output .Sine Wave Inverter Capacity 80 KVA, Rated Power 64000 W Supports Eight battery 24 Month Warranty Safe for sensitive appliances with Sine wave out-put Cruze HKVA Inverters can run heavy loads like AC, Geyser, Petrol Pumps, Photocopiers, Dental Chairs etc., depending on their capacity (please check the inverter capacity and your power requirement) Auto over-load handling capacity Installation and maintenance friendly Offers high quality and reliable power back-up solution for office and homes MCB for protection from Input mains Bypass switch for supplying output directly from grid in case of Home UPS fault. Noiseless Operations with the help of low harmonic distortion Intuitive Display to easily understand status of mains availability, battery status, etc. Comprehensive protection against short-circuit, reverse polarity, battery over-charge, deep-discharge etc Adaptive Battery charging control system technology (ABCC) ensures faster battery charging and enhances battery life by around 70% Supports a wide battery range, i.e. Flat Plate, Tubular & VRLA (SMF)

Supply and fixing in position 1000 mm wide rubber matting of 1100 volts grade as per electricity rules (exact length rubber mats to be worked out as per site requirement). Thickness of rubber mats shall be not less than 6 mm.

Providing and fixing steel structure work for supporting UPS & battery cabinets.

Installation, testing and commissioning of ceiling fan,wiring the down rods of standard length (upto 30 cm) with 1.5 sq. including mm FR PVC insulated, copper conductor, single core cable,including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor,single core cable and earthing etc. as required.

24" dia sweep wall bracket fan (BEE 5 star rated) of approved make complete with all accessories.

48" dia sweep ceiling fan (BEE 5 star rated) of approved make complete with all accessories.

Design, Manufacture, Supply, erection, testing and commissioning of 300 kVA, 415V, 3 Phase, 4 Wire, 50 Hz at 0.8 p.f. prime continuous (actual) rating radiator cooled diesel generating set in acoustic enclosure with radiator, Water cooled engine, PMG, base frame, Alternator, Static Excitation System, Lube Oil System, Electronic Governor, 24V Batteries & Battery Charger, Instrumentation, day oil fuel tank, Residential Silencer with Bellows, Alarms, microprocessor based Engine Control Panel, AVR Panel ,equivalent for AMF facility, termination adopter box suitable for XLPE insulated aluminium cables, drip trays space for mounting all associated equipments/ works as per specification including providing common base plate, anti vibration isolators, foundation bolts etc. The civil works for foundation for D.G.Set shall not be included in the rate. But other accessories like grouting screws, anti-vibration pads etc. shall be included in the rate. Alternator shall have class H insulation and rated for 100 KW output at 50°C. Emergency stop push button for individual DG set shall be located at the exit door. Engine shall not be derated upto 50 deg.C ambient. Note: Piping between day oil tank & DG set shall be included.

CONFERENCE TABLE CBL OFFICE FURNITURES Executive Table with One side pedestal unit (CBL01478)

CONFERENCE CHAIR GODREJ INTERIO Revolving Chair with Swivel tilt mechanism GODREJ INTERIOR (GODREJ INTERIO PREMIUM EXECUTIVE VERY HIGH BACK)

BOSS CHAIR GODREJ INTERIO Revolving Chair with Synchronic tilt mechanism

CHAIR Superior Non-Revolving and Non-Tilting chair without Armrest

WORK STATION GODREJ INTERIO Modular Work Stations with Single Seater Rectangular Cluster GODREJ INTERIOR (GODREJ INTERIO UPBEAT RECTA MODULE 1-SEATER)

OFFICE CHAIR Doris Fray Non-Revolving and Non-Tilting chair with Armrest Doris Frayr

ALMIRAH FURNHARDT Almirah Steel shelving cabinet with partial wardrobe FURNHARDTR (ALMARI STEEL (100MM X 900MM X480MM))

EXECUTIVE TABLE Featherlite Executive Table with One side pedestal unit

EXECUTIVE CHAIR Featherlite Non-Revolving and Non-Tilting chair with Armrest FeatherliteR (Tycoon Visitor Chair-Featherlite)

3 SEATER SEATING Galaxy 3 Seater Public Place Seating Chair of M S ERW tube with arm and backrest WITHOUT CUSHION

EXECUTIVE COMPUTER TABLE DURIAN 1525 millimeter X 760 millimeter (mm LxD) Executive Computer Table

COMPUTER CHAIR FLOYD Revolving Chair with Swivel tilt mechanism

DIRECTOR TABLE GODREJ INTERIO Executive Table with Both side pedestal unit

FILE STORAGE Doris Fray Movable File Storage System (Compactor) 2-Bay Sprocket Chain Drive Mechanism

CONFERENCE TABLE GODREJ INTERIO 10 seaters Meeting Table

ROLLER BLINDS FABRICO FURNITURE Sun screen roller blind (FB - 220)

CONFERENCE HALL Supplying, installation, testing and commissioning of audio/visual conference system

VACUUM CIRCUIT BREAKER PANEL Supply, Erection, Testing & Commissioning of 12kV, 3Ph, 50Hz, 400A, 20 - 26.3kA for 3Sec., "Indoor VCB Panel" for following incoming with SF6 insulated load break switch & outgoings with PVC sleeved copper bus bar & motorised horizontal draw-out type VCBs. The panel shall be floor mounted, totally enclosed MS sheet clad cubicle type & non-extensible on either side. The tripping mechanism shall be suitable for 24/48/110/220V DC source & 230V AC source for spring charge & heater circuit. The installation shall confirm IS : 10118 (Part III) - 1982 & amended upto date. The rate shall be inclusive of necessary civil works, mounting channels, earthing etc. complete in all respect. INCOMING 1no 400A,12V, 20kA SF6 insulated load break switch & suitable for termination of 11kV 3Cx185Sqmm XLPE(E) HT cable with a three position switch-disconnector, earth switch, manometer, cable bushing interface & fitted with fixed type voltage indicator device (VPIS -voltage presence indication system) as per IEC 61958 etc. complete in all respects. OUTGOING 1no. 400A, 11kV, 20kA SF6 insulated VCB unit & suitable for termination of 11kV 3Cx185Sqmm XLPE(E) HT cable with provision of making ON/OFF by manual spring charging, with ON/OFF/Trip indication at panel, earth switch, manometer, with self-powered transformer protection relay having 3 overcurrent & 01 Earth fault elements, with ring core current transformers of 50/1 & 5P10 class and fitted with fixed type voltage indicator device as per IEC 61958 etc. complete in all respects.

CAST RESIN TYPE DRY TRANSFORMER Supply, Erection, Testing & Commissioning of 400kVA, 11kV/415V, 350MVA, Dyn11, AN type indoor mounting copper wound, "Cast Resin Type Dry Transformer" with Class- H insulation,off load tap link, winding temperature indicator, bidirectional rollers, marshalling box, cable box with HT disconnecting chamber and LT disconnecting chamber on LT side and all other accessories as required. The off load tap link with (+)5% and (-)5% tappings in step of 2.5%. The installation shall confirm IS : 10028.1981(Part II) & amended upto date. The rate shall be inclusive of necessary civil works, mounting channels, earthing etc. complete in all respect.

HT CABLE Supply & Laying of "11kV, 3C HT XLPE(E) Al. Armoured Cable". The rate shall be inclusive of necessary supporting & clamping arrangement for laying of cables within tray/pipe/trench. The installation shall confirm IS : 1255.1983 & amended upto date. 11KV, 3C X 185SQMM XLPE ALUMINIUM CABLE.

HT CABLE END TERMINATION Supply & Fixing of "Heat Shrinkbale Indoor Type Cable End Termination Kit" suitable for the 11kV XLPE(E) cable with epoxy/polyurethane resin based kits, tapes, push on kits, multiconductor construciton etc. complete. The installation shall confirm IS : 1255.1983 & amended upto date. 11KV, 3C X 120-185 SQMM XLPE CABLE END TERMINATION KIT.

EARTH PIT Construction of "Earth Station" shall confirm IS-3043 with excavation, brick masonary work, GI funnel, salt, charcoal and earth lead connections etc as required.The GI funnel and tapping connection shall not be greater than 10" from the FFL. WITH 600X600X3MM "COPPER PLATE" AT A DEPTH OF 3METER WITH 50MM DIA 3M LONG "GI PIPE ELECTRODE (ISI-MEDIUM,CLASS-B)" AND 2NOS EARTH LEAD WIRES EACH OF 25X3MM CU-STRIP ELECTRODE.

Construction of "Earth Station" shall confirm IS-3043 with excavation, brick masonary work, GI funnel, salt, charcoal and earth lead connections etc as required.The GI funnel and tapping connection shall not be greater than 10" from the FFL. WITH 50MM DIA 3M LONG "GI PIPE ELECTRODE (ISI-MEDIUM,CLASS-B".

EARTH PIT COVER FRP MADE SQUARE 300MMX300MM.(12.5MT) WITH FRAME.

EARTH STRIP Supply & Laying of "Earth Strip" on wall/tray/trench including connections by bolting/riveting/welding etc. as required etc. complete. WITH 25X6MM GI STRIP.

EARTH STRIP Supply & Laying of "Earth Strip" on wall/tray/trench including connections by bolting/riveting/welding etc. as required etc. complete. WITH 50X6MM GI STRIP.

SAFETY ITEM Rubber mats upto 11KV grade(CLASS-C), 1.0METERX2.0METER and of 2.5 mm thickness and confirm IS:15652:2006.

Supply & fixing of wooden bound, glass covered, Shock treatment chart(both in Bengali & English) on wall with necessary screw & other as required

Supply & fixing of First Aid Box complete with all items as required

Supply & fixing of Danger Board for High voltage, 11KV,415V (250X200mm.) as per IS both in English & Bengali

STATUTORY CHARGES Liasoning & Obtaining preliminary & final NOC from the "Directorate Of Electricity".

Feeder Pillar: Design, fabrication, assembling, wiring, testing, supply, forwarding to site, unloading, shifting to location, inspection, installation, testing and commissioning of M.V.FEEDER PILLAR OUTDOOR TYPE Boards suitable for 415V, 3 phase, 4 wire, 50Hz distribution system. The panel shall be fabricated out of 2 MM CRCA sheet steel in cubicle formation, compartmentalized, form 3b construction, free standing, floor mounting, dust and vermin proof with reinforcement of suitable size angle iron, channel, 'T' sections and/ or flats wherever necessary. The panel shall be treated with anti corrosive process before final powder coating. Separate earth bus shall be provided throughout the length of the panel. The incoming and the outgoing feeder breakers, switch fuse units, change over switches, indicating lamps, meters etc. shall be accommodated in a modular multi tier arrangement. A minimum of 400mm clearance shall be given from the floor level to the bottom most termination point. The painting shall be done in conformity with IS code.Adequate size cable alley shall be provided all round the panel and at the back for easy bending and terminations. The outgoing feeders inside the panel shall be connected through solid bus bars. Flexible cable links are not acceptable. Bus bars shall be provided with PVC heat shrinkable sleeves or heat resistant insulated paint. The panels shall be suitable for cable entry from top / bottom. The copper earth strip of adequate size in 2 runs shall run through out the perimeter of the bottom of the panel. The panel shall be fabricated only after the approval of fabrication drawings by the consultant. 63 Amp Al bus Bar Suitable timer and contactor arrangement to be maid off Panel as above 16 AMP TPN MCB 10KA-8 nos 40 AMP FP MCB 10KA-1 nos

Light Fixtures: Supply and fixing of LED POST TOP 12W WARM of Jaquar make GTP-GRYLGTP01X012XW in 2 meter steel tubular pole including civil foundation with all necessary arrangement.

Supply and fixing 10W bollard light with loopin/out and civil foundation ,wiring complete with all necessary arrangement.

Cable and accessories: 4 core x 10.0 sq. mm. XLPE, Al.armoured cable.

Cable and accessories: 4 core x 16.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 10.0 sq. mm. XLPE, Al.armoured cable.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 core x 16.0 sq. mm. XLPE, Al.armoured cable.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Earthing: Providing and fixing 6 SWG dia G.I. wire on surface or in recess for earthing along with existing surface/ recessed conduit as required.(pole Earthing)

Supply and fixing 1 meter long GI Spike for pole earthing .

DC INVERTER VARIABLE REFRIGERANT FLOW SYSTEM (VRF) (Make: Toshiba/Mitsubishi/O-General/Carrier) Supply of Outdoor Unit : VRF ODU UNITS Supply of Hi efficient latest generation Imported Top Discharge Type DC Inverter Outdoor VRF units ( BMS compatible ) equipped with Variable refrigerant flow unit ( Heating & Cooling ), comprising Full Inverter driven Scroll compressors ( with EVI technology ) with fully factory charged Eco friendly R-410A refrigerent gas. All the unit shall be provided with micro processor based control for sequential starting of condensing units,scanner for fault analysis at ODU ,dual EXV control, 4 stage precise oil control technology, DC motor condenser fan, intelligent defrosting technology, inbuild night Silent operation ,Refrigerant cooling PCB , various electrical protection like-phase sequence,high /low voltage protection ,compressor overload protection,fan & compressor temparature protection & pressure protection. There must be only Full DC inverter compressor in each module. There must be atlest 2 Full DC inverter compressors in each module. Compressor make must be same as the machine make (Make: Toshiba/Mitsubishi/O-General/Carrier) 18HP HEAT PUMP TYPE OUTDOOR UNIT WITH 2 NOS. FULL DC INVERTER COMPRESSORS

20HP HEAT PUMP TYPE OUTDOOR UNIT WITH 2 NOS. FULL DC INVERTER COMPRESSORS

Supply of VRF INDOOR Unit : Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities. VRF Mid Static duct type Indoor Unit with In built Drain pump :- Supply of Air Cooled VRV/ VRF Mid static celing mounted compact conceal duct type Indoor unit with cordless remote . The unit shall be insulated with sound absorbing thermal insulation material, Polystyrene / Polyethylene foam ,comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. The unit shall be supplied with resin built in net filter . The unit shall be supplied with inbuilt drain pump, drain hose, clamp metal for hanging bracket & insulation for fitting. MID STATIC COMPACT CONCEAL DUCT Type : 2.0TR

Supply of VRF INDOOR Unit : Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities. VRF Mid Static duct type Indoor Unit with In built Drain pump :- Supply of Air Cooled VRV/ VRF Mid static celing mounted compact conceal duct type Indoor unit with cordless remote . The unit shall be insulated with sound absorbing thermal insulation material, Polystyrene / Polyethylene foam ,comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. The unit shall be supplied with resin built in net filter . The unit shall be supplied with inbuilt drain pump, drain hose, clamp metal for hanging bracket & insulation for fitting. MID STATIC COMPACT CONCEAL DUCT Type : 2.8TR

Supply of Air Cooled VRF HI-WALL Indoor unit (heatin& cooling type) with cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner coil,minimum 4 step louver function ,auto addressing,follow me,anti cold air function, auto defrosting , LED display,pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion & Inbuilt water pump price included . 1.3TR Hi-wall Type VRF Indoor

Supply of Air Cooled VRF HI-WALL Indoor unit (heatin& cooling type) with cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner coil,minimum 4 step louver function ,auto addressing,follow me,anti cold air function, auto defrosting , LED display,pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion & Inbuilt water pump price included . 1.6TR Hi-wall Type VRF Indoor

Supply of Air Cooled VRF HI-WALL Indoor unit (heatin& cooling type) with cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner coil,minimum 4 step louver function ,auto addressing,follow me,anti cold air function, auto defrosting , LED display,pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion & Inbuilt water pump price included . 2.0TR Hi-wall Type VRF Indoor

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 1.0 TR (Compact)

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 1.3 TR (Compact)

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 1.6 TR

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 2.0 TR

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 2.3 TR

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 2.6 TR

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 3.2 TR

Supply of Air Cooled VRF 4 way Cassette type Indoor unit with Inbuilt drain pump & cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Including grille panel. Minimum capacities of each Evaporative units are as follows: Cassette type VRF Indoor 4.0 TR

Supply of Air Cooled VRF Hi static duct type indoor unit with cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. HSD type VRF Indoor 5.68 TR

Supply of Air Cooled VRF Hi static duct type indoor unit with cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. HSD type VRF Indoor 8.0 TR

Supply of Air Cooled VRF Hi static duct type indoor unit with cordless remote, comprising of micro processor based side panel for sequential starting of blower fan / runner,coils, thermostat, pulse modulating electronic expansion valve (PMV), tubes,fins with specially factory coated hydrophilic treatment for heat & rust corrossion. Supply of remote controller for cassette type Acs

INSTALLATION WORKS OF VRF SYSTEM WITH SUPPLY OF FITTING ITEMS Control cabling for VRF to be laid within hard PVC conduit pipes with proper bends and accessories (Make: Havells/Polycab/USHA/RR Kabel/Equivalent) 1.5sq.mm. 3-core shielded communication cable between indoor units and outdoor unit

CPVC Drain Piping with 9MM Nitrile rubber insulation. Drain pipes to be suspended from slab using full threaded rods and slotted channel along with all required accessories (Make: Ashirwad/Supreme/Ajay/Prince/Shakti Gold/Equivalent.) Drain piping 25 mm dia

CPVC Drain Piping with 9MM Nitrile rubber insulation. Drain pipes to be suspended from slab using full threaded rods and slotted channel along with all required accessories (Make: Ashirwad/Supreme/Ajay/Prince/Shakti Gold/Equivalent.) Drain piping 40 mm dia

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant Piping 42 mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant Piping 38.1 mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant Piping 34.9 mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant Piping 31.8 mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 28.6 mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 25.4mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 22.2mm dia with (19MM Class 'O' Insulation) (18G Copper Pipes)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 19.1mm dia with (19MM Class 'O' Insulation) (1mm Thck. Gauge)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 15.9mm dia with (19MM Class 'O' Insulation) (1mm Thck. Gauge seamless tubing)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 12.7mm dia with (19MM Class 'O' Insulation) (0.8mm Thck. Gauge seamless tubing)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be providedRefrigerant piping 9.5mm dia with (19MM Class 'O' Insulation) (0.8mm Thck. Gauge seamless tubing)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Refrigerant piping 6.4mm dia with (19MM Class 'O' Insulation) (0.8mm Thck. Gauge seamless tubing)

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided Y Joints for Indoor Units

Supply of copper refrigerant pipes suitable for R410A Refrigerant with 19 MM CLASS-'O' Nitrile rubber insulation respectively for Suction & Discharge Pipes. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes. Suspended supports from slab using full threaded rods and slotted channels to be provided with PVC Sleeve on each resting point of copper-nitrile insulation. (Copper pipe make: Mandev/Universal/Totaline/Mexflow/Camipro or Equivalent). (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline)Quality & Test Certificate to be provided T Joints for Indoor Units

R410A Eco-Friendly Refrigerant (Make: Fluoron/Value). Quality Certificate to be provided

Installation of 1.5sq.mm. 3-core shielded communication

Installation of Drain Piping 25MM dia

Installation charge for Drain Piping 40mm dia

Installation charge for Refrigrant Piping 42 MM

Installation charge for Refrigrant Piping 38.1 MM

Installation charge for Refrigrant Piping 34.9 MM

Installation charge for Refrigrant Piping 31.8MM

Installation charge for Refrigrant Piping 28.6MM

Installation charge for Refrigrant Piping 25.4MM

Installation charge for Refrigrant Piping 22.2MM

Installation charge for Refrigrant Piping 19.1MM

Installation charge for Refrigrant Piping 15.9MM

Installation charge for Refrigrant Piping 12.7MM

Installation charge for Refrigrant Piping 9.5MM

Installation charge for Refrigrant Piping 6.4MM

ITC charges for Top Discharge ODU

ITC charges for Hi Static Ductable indoor unit

ITC charges for Cassette Type Units

ITC charges for Hi-wall Type Units

ITC charges Mid-Static Units

R410A Eco-Friendly Refrigerant Charging

Supply, Fixing, Testing and Balancing of GI sheet metal Site Fabricated rectangular ducting as per IS 655 complete with turning vanes , companion flanges , structural support , sealing of all seams with a suitable metal sealant, completely leak proof as per drawings (Make: Tata/Sail/Bhushan/Arti) 24 G GI Sheet

Supply and fixing of 100% Thermal insulation with Class -'O' closed cell nitrile rubber insulation sheet duly pasted on the duct inside surface using SR988 or approved equal adhesive. All insulation joints shall be sealed with 50MM nitrile rubber self-adhesive tapes(Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline) Quality & Test Certificate to be provided 13MM

Supply and fixing of duct acoustic insulation with Class -'O' Nitrile insulation sheet duly pasted on the duct inside surface using SR988 or approved equal adhesive (Insulation make: K-Flex, Accoflex,Armacell/ Camipro,Totaline) Quality & Test Certificate to be provided 15MM

Supply, installation, testing and balancing of Linear Discreet Grill with 15 Deg Deflecting linear bars in extruded aluminum construction with white powder coated finish. (Make: Airflow / Ravistar/Caryaire/Waves)

Canvas connection with frie retardant flexible canvas cloth

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width x 50 mm depth x 1.6 mm thickness.

Axial flow fans Supply, installation, testing & commissioning of fans for exhaust complete with motor suitable for 220 Volts 50Hz, single phase, AC supply with supporting arrangement and flexible connection etc. as required and as per specifications. 1000 CFM

Axial flow fans Supply, installation, testing & commissioning of fans for exhaust complete with motor suitable for 220 Volts 50Hz, single phase, AC supply with supporting arrangement and flexible connection etc. as required and as per specifications. 800 CFM

VI Rubber Pading for outdoor units

Outdoor unit floor lifting and positioning charges

MS Stand for Outdoor units

M/S N.E. Infra