Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹8.9 LAccepted-Finance V AMB P O TEHSIL JAWALAMUKHI DISTT KANGRA H P | KANGRA | HIMACHAL PRADESH | 175013 | L1 | Accepted-Finance L1 | |
| 2 | L2₹9.3 L+₹33,083.27 (3.71%)Rejected-Finance VILLAGE PO AND TEHSIL DEHRA DISTT KANGRA HP | KANGRA | HIMACHAL PRADESH | 175013 | L2 | Rejected-Finance L2 | |
| 3 | L3₹9.6 L+₹70,845.60 (7.94%)Rejected-Finance | L3 | Rejected-Finance L3 |
Tender Value
₹8.3 L
EMD Value
₹16,650
Closing Date
17 Feb 2024, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
EXECUTIVE ENGINEER
jal shakti division Dharmashala
Cons of underground water storage tank 50000 ltr capacity at village Kandi
2024_HPIPH_84913_1
EE/JSD/EA-1/ 30285-30384
Open Tender
Civil Works
Item Wise
90 days
DHARAMSHALA
Please refer Tender documents.
6 documents required · 6 mandatory
₹400
EE JSD
₹16,650
27 Mar 2025
1 Feb 2024
17 Feb 2024
1 Feb 2024
17 Feb 2024
5 Feb 2024
1 Feb 2024 - 17 Feb 2024
Amount
Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick Work, jumper work, blasting hard or softs rock by chiselling where the blasting work is prohibited slushy daldal and saturated soil including pumping or bailing out water within all heights, stacking the excavated soil within all leads clear from the edge of excavation and then returning the stacked soil in 15Cm (fifteen Centimetres) layer when required into plinths, sides of foundation consolidating each depossited layer by ramming and watering and then disposing of all surplus excavated earth complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Providing and laying cement concrete 1:3:6 (1cement:3 sand:6 graded stone aggregate 20mm nominal size) curring complete excluding cost of form work in foundation and plinth complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, and propping etc. height of propping and centring below supporting floor to ceiling not exceeding 4mtrs.and removal of the same for in-situ-reinforced concrete and plain concrete work in:
Vertical surfaces such as walls (only thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like complete in all respect including all leads and lifts.
Sides and soffits of beams, beam haunching cantilever bresummers and lintels not excedding 1 mtr in depth in all height from floor complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Providing form work of ordinary timber planking so as to give a rough finish including centring, shuttering and propping etc. height of propping and centring below supporting floor to ceiling not exceeding 4mtrs.and removal of the same for in-situ-reinforced concrete and plain concrete work in: Arches up to 6 mtr span complete in all respect with in all leads and lifts.
Providing and Laying cement concrete 1:1½:3 (1 Cement:1½ Sand:3 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-
In foundation, footings, bases of columns etc and mass concrete complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
In walls any thickness (but not less than 0.10mm thickness) including attached buttersses pillaster plinth and string courses etc. from top of foundation level upto floor two level complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Suspended floors, roofs landing and shelves and their support balconies, beams, girders, bressumers and cantilever upto floor two level complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Providing and Laying Mild steel /Tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level (tor steel) complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Providing Steel work welded in built up section trusses and framed work including cuttint, hosting fixing in position and applying a priming coat of red lead paint in grating framed guards bars, ladders, railing brackets and similar works complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Providing and fixing cast iron man hole cover, 560 mm dia with frame (medium duty). Weight of frame 58 kg and weight of cover 58 kg. Total weight of frame and cover not less than 58 kg.
Providing, fixing, Laying and galvanized wire Masquito proof ventilator size 600 mm dia and 300 mm in hieght with frame of M.S. angle iron 40x40x6 mm complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Laying, jointing & testing of GMS (plan ended pipe) with circumfrential 90% butt welded joints & 10% for flange joint with MS flanges i/c nuts, bolts, rubber gasket etc of following dia by electrical arc welding with minimum two layers capable to withstand required test pressure (minimum welding thickness shall be equal to pipe wall thickness) including manufacturing and fabrication of reducers/ tapers, all short pieces, bends of required degree as per site requirement made from parent tubes. The laying of pipe shall also include intermediate flanged joints spaced at an interval of 15 pipe lengths or where ever required as per direction of the Engineer-in-charge dully welded in three layers (two for outer & one on inner side) and all other operation such as cutting, cleaning, welding, jointing, fabrication of bends, tees etc, lowering and laying in excavated trench to ensure required level i/c flushing, cleaning, and hydraulic testing complete in all respect & to the entire satisfaction of the Engineer-in-Charge (Earth work in trenches will be measured and paid for separately). The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The welding electrodes shall be as per IS 814 of Advani Oerlikon/L&T or ISI marked make. The damaged portion of the pipes and all the specials (if damaged during laying & jointing operation of pipe) made from the parent tube shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paint over a priming coat as per AWWA specifications C-203-1978. The rates also includes entire carriage of material, flushing, cleaning of butt welded joints complete in all respect and to the best satisfaction & direction of Engineer in charge with in all leads and lifts.100mm dia (M), Table-5
Providing and fixing of double flanged cast iron Sluice valve 100 mm Dia of BIR/Kartar make class PN-1.6 conforming to BIS: 14846 capable of with standing nominal seat test pressure 16kg/cm² complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Finishing walls with water proofing cement paint of approved brand and manufacture of required shade on un-decorated wall surface (two coats) to give an even shade after throughly brushing the surface to remove all dirt, dust and remains of loose material sand papered stopping complete in all respect including all leads and Lifts as per the direction and to the entire satisfection of Engineer-In-Charge.
Extra cost for providing and mixing polyester triangular synthetic fibres in specified ration 6-18mm length designed for melting point 240-260 degree centigrade and having specific gravity of 1.33-140 as per IS-456 amendment August 2007 & IRC 44- 2008 @ 125 grams/50kg of cement bag in all types of CC, RCC, plastering and flooring work etc.
Provision for Drawing & Design and Bearing capacity of soil complete in all respect.
aman sood
AJAY KUMAR GOVT. CONTRACTOR
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .