Tender for Renovation and alteration work for proposed IPHL facilities at DHH, Puri, Odisha including architectural consultancy services.

Tender for Renovation and alteration work for proposed IPHL facilities at DHH, Puri, Odisha including architectural consultancy services.

Tender for Renovation and alteration work for proposed IPHL facilities at DHH, Puri, Odisha including architectural consultancy services.

NIT No: PCO/BBSR/951/241 dated 06.02.2026

Grand Total

Rupees:

Tender for Renovation and alteration work for proposed IPHL facilities at DHH, Puri, Odisha including architectural consultancy services.

NIT No: PCO/BBSR/951/941 dated 06.02.2026

Providing, lifting, hoisting and laying Reinforced cement concrete of M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm. size black hard crushed broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned ( 20mm. size chips not to exceeds 25 % ) to be mixed in concrete mixture with Portland slag cement (PSC) including hoisting, lowering, laying and compaction concrete by using vibrators, watering and curing for 28 days, centering and shuttering then after dismantling and removing debris from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties and taxes of all materials and cost of all labours, sundries, T & P required of the work etc. complete in all respect as directed by the Engineer-in-Charge. But excluding cost and conveyance of M.S. rods or Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel tying the grills and placing in proper position.

Providing HYSD reinforcement of approved quality confirming to grade Fe-550D for R.C.C. work including cutting, bending, binding and tying the grills and placing in position including cost of binding wire 18 to 20 gauge and cost and carriage of steel. etc. complete with labour cess, including 5% overlaaping & wastage etc. as directed by the Engineer-in-charge.

Brick work with Fly ash Bricks 25cm x 12cm x 8cm size having crushing strength not less than 75Kg/cm2 with dimensional tolerance ±2 percent in cement mortar (1:6) in superstructure including watering curing, cost of carriage and royalty of all materials, cost of all labour as directed by the Engineer-in-charge.

Ground Floor

First Floor

Brick work with Fly ash Bricks 25cm x 12cm x 8cm size having crushing strength not less than 75Kg/cm2 with dimensional tolerance ±2 percent in cement mortar (1:4) in superstructure including watering curing, cost of carriage and royalty of all materials, cost of all labour as directed by the Engineer-in-charge.

Ground Floor

First Floor

Providing 16mm thick C.P. (1:6) over brick masonary to the smooth surface including watering, curing cost, carriage, royalty, and taxes of all materials, cost of all labour, etc complete as per the direction of Engineer-in-charge.

Ground Floor

First Floor

Providing 12mm thick C.P.(1:6) on brick masonary to the smooth surface including watering, curing, cost, carriage, royalty of all materials, cost of all labour, etc complete as directed by the Engineer-in-charge.

Ground Floor

Providing 6mm thick C.P.(1:4) on brick masonary to the smooth surface including watering, curing, cost, carriage, royalty of all materials, cost of all labour, etc complete as directed by the Engineer-in-charge.

Ground Floor

First Floor

Supplying, fitting and fixing Ceramic tiles (300x450) in dados skirting and risers of steps on 12mm thick CP (1:3) jointed with neat cement slurry mixed with pigments to match the shade of the tiles and epoxy grouting using spacers of approved quality including cost of all materials, labours ,T&P, carriage, royalty, taxes etc. required for the work all complete as per direction of Engineer-in-charge.

Ground Floor

First Floor

Supplying, fitting and fixing Granite tiles of size above 0.40 sqm in floors of approved make confirming to IS:13755 laid on 20 mm thick cement mortar (1:4) and filling joints with neat cement slurry mixed with pigments to match the shade of the tiles of approved quality including cost of all materials, labours ,T&P, carriage, royalty, taxes etc. required for the work all complete as per direction of Engineer-in-charge.

Ground Floor

First Floor

Supplying, fitting and fixing Granite tiles of size above 0.40 sqm in dados skirting and risers of steps on 12mm thick CP (1:3) jointed with neat cement slurry mixed with pigments to match the shade of the tiles of approved quality including cost of all materials, labours ,T&P, carriage, royalty, taxes etc. required for the work all complete as per direction of Engineer-in-charge.

Ground Floor

First Floor

Finishing plastered wall surface with Cement based Wall putty (water based) of approved make and finished smooth & even surface to receive painting including cost of scaffolding etc. with cost of all materials, labours ,T&P, carriage, royalty, taxes etc. required for the work all complete as per direction of Engineer-in-charge.

Inside

Ground Floor

First Floor

Priming one coat with Wall Primer water bond cement primer including cost of all materials, labours ,T&P, carriage, royalty, taxes etc. required for the work all complete as per direction of Engineer-in-charge.

Inside

Ground Floor

First Floor

Wall painting two coats with plastic emulsion paint of approved shade on new work to give an even shade including cost of all materials, labours ,T&P, carriage, royalty, taxes etc. required for the work all complete as per direction of Engineer-in-charge.

Ground Floor

First Floor

Supplying and fitting-fixing of two rack Un-plasticised Poly Vinyl Chloride (UPVC) sliding window of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures etc. complete in all respect as per the direction of the Engineer-in-Charge.

Supplying, fitting and fixing of openable UPVC doors with door frame of approved make with 6mm thick glass of approved quality complete with frame, shutters and all fitting and fixtures etc. in all respect as per the direction of the Engineer-in-Charge.

Supplying, fitting and fixing of UPVC Partition Wall I60 Casement Series 1-OFF as per drawing and specification: Top member-6mm Tinted/Laminated/Colored/Clear Toughened Glass & Bottom member-PVC Sheet (12-18mm), Weight: 291.36 kg, Colour-White Dimension Type-Frame Size from RO, Frame Depth-60mm, Hinged Series-I60 Casement, Reinforcement-Full, Coupling 180-33mm/2108-3106+56016-10070, Window O/F-55mm/41101-11000+R1, Frame T/M-74mm/41101-12000/12100+56016-10001, T-Joins-Mechanical, Frame Mech-50502-11016, Connector-Shape 1, Bead Shape-Glazing Packer 16.5 x 77 x 5 mm, Cmnt Gl Packer-No, Grill required-Supply & Install, Supply Type-280ml bottle, Silicon Sealant-No, Display Fixings-Face with drainage including scaffolding complete in all respect as per the direction of the Engineer-in-Charge.

BWP 710 Grade Plywood & Mica Work - Making and fixing plywood work as per drawing and specification (main Str./body 18-19mm, doors 12-15mm, back panel 6-9mm thickness) with mica finishing for cupboard/racks/shelves/wardrobe with all necessary accessories i.e. metal handles, hinges, clamps, locks and screws etc. of approved quality including cost of all materials, labour & T&P etc complete as per direction of the Engineer-in-charge.

Providing and fixing GI chicken wire mesh 24 gauge and 12 mm mesh and required wideth for construction joints and chasing in brick work for electrical conduits or water supply pipes including cement slurry and pegs/nails with nailing machine as required before pastering etc. complete as directed by the Engineer-in-charge.

Dismantling brick or stone masonry in cement mortar under 3m. height including stacking the useful materials for reuse and removing the debris within 50m. lead etc. as directed by the Engineer-in-charge.

Dismentaling & removing R.C.C columns beams, slab, staircase, landing, lintels, including stacking the useful materials for the reuse and removing the debries within 50m lead etc. as directed by the Engineer-in-charge.

Dismentaling & removing Doors, Windows and ventilators including Removal of frame, hinges, fastening and stacking the useful materials for the reuse and removing the debries within 50m lead etc. as directed by the Engineer-in-charge.

Dismentaling and removing old tiles flooring including removing the base coarse and stacking the useful materials for reuse and removing the debris within 50m lead etc. as directed by the Engineer-in-charge.

Dismantling and removing old tiled cladding from walls including racking out joints 12mm deep stacking the useful materials for reuse and removing the debris within 50m lead etc. as directed by the Engineer-in-charge.

Dismantling aluminium/ gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead as directed by Engineer-in-charge.

TOTAL CIVIL & INTERIOR WORK (A)

INTERNAL WIRING.

Recessed wiring to light point / first light of group control/ call bell point/ exhaust fan point /wall fan point with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia non-metalic PVC conduit with 6 Amp, 250 V clip in type switch ISI marked and ceiling rose ISI marked mounted on G.I modular box with face plate & cover of suitable size , with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer in Charge. (Make of wire Finolex /Polycab/ Anchor / Havels/Eq) (Make of modular box,cover,switch & socket-Legrand Arteor/schneider Zencelo/Panasonic Vision/Eq) With 10Years Warenty

Group C

Recessed wiring to secondary light point looped from primary light point with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non-metallic PVC conduit with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor for running earth including 3 plate ISI marked Ceiling rose with all accessories & connection as per direction of Engineer-in-charge. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) Average Length: 3 mtr

Recessed wiring to ceiling fan point with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non-metallic PVC conduit with 6Amp 250V Modular Switch,Stepped type Moudular Regulator, Base & Cover with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor for running earth including all accessories & connection as per direction of Engineer in charge. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) Group c

Recessed wiring to Twin control light point with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia non-metalic PVC conduit with 6Amp, 250 V clip in type 2way switch ISI marked and ceiling rose ISI marked mounted on G.I modular box with face plate & cover of suitable size , with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection as per direction of Engineer-in-charge. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) Group C

Recessed wiring for 5 / 6 amp socket outlet with 6Amp, 250 V clip in type modular switch ISI marked mounted on G.I moular box with face plate & cover of suitable size including all accesories and connection on same switch board as per direction of Engineer-in-charge.

Recessed wiring for 5 / 6 amp socket outlet with 2 x 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia non-metalic PVC conduit with 6Amp, 250 V clip in type switch ISI marked mounted on G.I moular box with face plate & cover of suitable size , with 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire including all accesories and connection on separate board as per direction of Engineer-in-charge.(Make of wire KEI /Polycab/ Anchor / Havels/Eq) Group C

Recessed wiring for 2 x 6 amp socket outlet controlled by 2 nos 6Amp, 250 V clip in type switch ISI marked mounted on single G.I moular box with face plate & cover of suitable size including all accesories and connection on separate board as per direction of Engineer-in-charge.

Recessed wiring for 6 pin 16 amp socket outlet with 16Amp, 250 V clip in type switch ISI marked mounted on G.I moular box with face plate & cover of suitable size including all accesories and connection as per direction of Engineer-in-charge.

Recessed wiring for A.C/ Power socket outlet with industrial type socket outlet, plug top and metal chained cover in sheet steel enclosure ,20A/32A SP MCB including all accesories and connection as per direction of Engineer-in-charge.

Recessed wiring to exhaust fan/Wall Fan point with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor of ISI marked with 20mm dia non-metallic PVC conduit with 6Amp 250V Modular Switch, Base & Cover with 1.5sqmm FRLSH PVC insulated single core multistrand copper conductor for running earth including all accessories & connection as per direction of Engineer in charge. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) Group C

Call bell point

Recessed wiring for 3 x 6 amp socket outlet controlled by 2 nos 6Amp, 250 V clip in type switch ISI marked mounted on single G.I moular box with face plate & cover of suitable size including all accesories and connection on separate board as per direction of Engineer-in-charge.

Supplying and fixing 32 amps, 240 volts, SPN, industrial type socket outlet, with 2 pole and earth metal enclosed plug top along with 32 amps. C-series, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge.. . Make-Legrand/Schneider/Siemens ISI marked as approved,All the Components should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.(for Medical equipement only)

Supplying and fixing 63 amps, 415 volts, TPN, industrial type socket outlet, with 4 pole+E-4P plug & socket DB with 63A 4P MCB,C series,10ka as per IEC-61439-3 ,suitable for flush & surface mounting,supplied with neutral link with provision for mounting modular devices as per direction of Engg.-in-Charge.Make-Legrand/ Siemens/Schneider/ABB

SUBMAIN.

Recessed wiring to submain in 4 x 10 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 32 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 2 x 4 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire KEI /Polycab/ Anchor / Havels/Eq)

Recessed wiring to submain in 4 x 6 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 32 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 2 x 2.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire KEI /Polycab/ Anchor / Havels/Eq)

Recessed wiring to submain in 2 x 6 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 25 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 1 x 2.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire KEI /Polycab/ Anchor / Havels/Eq)

Recessed wiring to submain in 2 x 4 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 20 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 1 x 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire KEI /Polycab/ Anchor / Havels/Eq)

Recessed wiring to submain in 2 x 2.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 20 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 1 x 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire KEI /Polycab/ Anchor / Havels/Eq)

Recessed wiring to submain in 2 x 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 20 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 1 x 1.5 sq.mm FRLSH PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire KEI /Polycab/ Anchor / Havels/Eq) (For Switch Board Looping)

CABLE .

Supply & Laying of one number of PVC insulated and PVC seathed / XLPE power cable of 1.1 KV grade of 3.5core 35 sq.mm direct in ground including excavation , sand cushining protective covering and refilling the trench etc. as required.(Make-polycab/KEI/Rhino cable/Eq)

Supply & Laying of one number of PVC insulated and PVC seathed / XLPE power cable of 1.1 KV grade of 4 core 16 sq.mm Aluminium on surface as required.(Make-polycab/KEI/Rhino cable/Eq)

END TERMINATION

Supplying and making end termination with brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed / XLPE aluminum cable of 1.1 KV as required.

EARTHING

FIXTURE

Supply, Installation, Testing and Commissioning of pre-wired fluorescent fiiting / compact fluorescent fitting /LED fitting of all sizes complete with all accessories and lamp etc. directly on ceiling /wall or recessed in false ceiling , including connection with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor and earthing as required.Make-JAQUAR/Bajaj/Eq.With 5Years Warenty.

Ceiling mounted indoor type batten type LED Luminaire with LED Lamp Similar to JAQUAR Cat No. LGLZ01X024XW or equivalent.

Ceiling/ Wall mounted type BULK HEAD Luminaire with Similar to JAQUAR Cat No.LBLK02X010XW or equivalent.

Supply, Installation, testing and commissioning of 10W Mirror Light Similar to JAQUAR Cat no-LGLZ01X010XW/Equivalent.

Supply, Installation, Testing and Commissioning of ceiling fan 1200mm sweep, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated single core multiatrand copper conductor etc. as required.Model -USHA ENERGIA 32 BLDC 5 STAR.

Supply, Installation, testing and commissioning of exhaust fan of 300 mm sweep 900 rpm in the existing opening, including making the hole to suit the size of the above fan, making good the damage complete, connection, etc as required.Model-Usha AEROCLEAN.

Supply & fixing of 18W LED Down Light (S/R) similat to Jaquar Cat no-LNRO02S018SW/Equivalant With all accessories.

Supply & fixing of LED 36w 2'x2' Surface/Recessed Mounted Light similar to jaquar cat no-LULU2SL036XC / Equivalent. etc as required .

Supply & fixing of 6W LED Down Light (S/R) similat to Jaquar Cat no-LLCN01R006XC/Eq. model of Bajaj/Eq.with all accessories.

Supply, Installation, testing and commissioning of wall fan of 400 mm sweep as required.Model-400mm STRIKER HI SPEED.

Perforated Type Cable Tray

Supply and installation of Pregalvanised Perforated type cable trays without cover. The rate shall include bends, Tees, all supporting brackets, anchor fasteners, screws, bolts, nuts etc., including painting of cable trays. Thickness of sheet steel shall be 2 mm. Support sizes similar to ladder type trays

Size of Cable Tray :150 mm x 50 mm

TV /TEL & DATA

Supplying and fixing of clip in type modular Telephone socket ISI marked mounted on G.I modular box with face plate & cover of suitable size ,including all accesories and connection as per direction of Engineer in Charge.

Supplying and fixing of clip in type modular T.V. antenna socket ISI marked on mounted on G.I modular box with face plate & cover of suitable size , including all accesories and connection as per direction of Engineer in Charge.

Supplying and drawing 4 pair, 0.5 sq.mm FR PVC insulated coper conductor, unarmoured telephone cable in existing surface / recessed PVC conduit as required.

Recessed wiring to television point with cable RG-6 grade, 0.7 mm solid copper conductor PE insulated shielded with fine tined copper braid and protected with FR PVC sheath in in existing surface / recessed PVC conduit as required as per direction of Engineer in Charge.

Supplying and fixing of following sizes PVC conduit along with accessories in recessed wiring including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of 16 / 18 SWG metal box of 200 mm x 150 mm x 60 mm deep on surface / recess with suitable size of phenolic laminated sheet cover in front including cutting the wall and making good the same in case of recessed conduit as required. ( Tel junction Box)

Supplying & Commissioning of Telephone Hand Set.

Supplying & installation of 100 pair KRONE make moudles with locking & key arrangements fabricated with MS sheet & powder coated to be fixed on concealed manner incl. good the damages.

SITC of 4 pair Cat6 23 awg U/UTP LSZH Cable in the existing surface/ recessed steel/ PVC conduit as required: The 4 pair Unshielded Twisted Pair cable shall be UL Listed,exceeds the requirements of ANSI/TIA-568-C.2 and ISO/IEC 11801 Class E , 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must,Insertion Loss of 32.8 db/100m at 250 MHz ,Cable should support operating temperature from -20° to +70°C Cable support Conductor Resistance ≤ 9.38 Ω/100m Max., Cable support Delay Skew: < 45 ns/100m, Operating Voltage: 72V , Impedance: 100 ± 15 Ω @100 MHz. and Propagation Delay @250 MHz : 536 ns/100m, ETL Verified 4 connector channel performance up to 700 MHz , RoHS Compliant. Make: Systimax, Legrand, Panduit

TOTAL ELECTRICAL WORK (B)

Providing and fixing Clorinated Polyvinyl Chloride [CPVC] pipes SDR-11 conforming to IS:15778, having thermal stablity for hot & cold water supply , including all CPVC plain & brass threaded fitting including fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes and fittings with one stp CPVC solvent cement and testing of joints complete as per specification and direction of Enfineer-in-charge.

20 mm PVC sch-80 pipes

25 mm PVC sch-80 pipes

32 mm PVC sch-80 pipes

50 mm PVC sch-80 pipes

Supplying all materials,labour and T&P for cutting holes through existing brick work including making good to the same in cement mortar(1:4) for taking G.I. pipes and fittings /P.V.C. pipes and fittings all complete as per specification.

250mm Thick

Supplying all materials,labour and T&P for cutting holes in R.C.C. floors and roofs up to 19 cm. thick including for passing GI / PVC pipes and fittings etc. and repairing the holes after insertion of pipes etc. with cement concrete 1:2:4 including finishing complete to make it leak proof leak to the damages all complete as per specification and direction of the Engineer-in-charge.

Supplying all materials,labour and T&P for cutting groves in pucca floor and walls for taking G.I. pipes and fittings /P.V.C. pipes and fittings and making good to the damages all complete as per specification.

Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials complete as per specification and direction of the Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer-In-Charge.

110mm diameter PVC SWR pipes

75mm diameter PVC SWR pipes

110mm PVC door Tee

75mm PVC door Tee

110mm PVC offset

110mm PVC door bend

75mm PVC door bend

110mm PVC plain shoe bend

75mm PVC plain shoe bend

110mm PVC vent cowl

75mm PVC vent cowl

110mm S-trap

110mm P-trap

110mm SWR Pipe Clip

75mm SWR Pipe Clip

110/75 mm Dia Reducer/Connector

90mm Nahani Trap

Supplying all materials,labour and T&P for fixing wash hand basin with hole for pillar taps confirming to IS 2556:part4-2004 with cast iron /M.S. brackets painted white including cutting holes in walls and making good to the damages etc. all complete as per specification.

Supplying all materials,labour and T&P for fixing of 600x450 bevelled edge mirror of superior glass mounted on 6mm thick ac sheet or ply wood sheet and fixed to wooden plugs with chromium plated brass screws and washers etc. All complete as per specification .

600mmx450mm size B.E.mirror

Supplying all materials,labour and T&P for fixing standard size glass self with chromium plated brass brackets fixed to wooden plugs with chromium plated brass screws and washers etc. all complete as per specification.

Supplying all materials,labour and T&P for fixing standard size C. P. towel rail fixed with chromium plated brass brackets fixed to wooden plugs with cromium plated brass screws complete as per specification.

CP towel rail-

Supplying all materials,labour and T&P for fixing of cromium plated brass soap dish complete with chromium plated brass brackets fixed to wooden plugs with chromium plated brass screws as per specification.

CP soap dish-

Supplying all materials,labour and T&P for fixing standard size C. P. towel ring fixed fixed to wooden plugs with cromium plated brass screws complete as per specification.

Supplying all materials,labour and T&P for fixing of liquid soap container - glass container or plastic container with chromium plated brass lid and brackets fixed to wooden plugs with chromium plated brass screws as per specification.

Supplying all materials,labour and T&P for fixing Porcelain Lab Sink as per IS 13983 with cast iron bracet and stainless steel plug including painting of fittings and brackets ,cutting and making good to the walls etc. all as per specification including cost of sink with all accessories.

Supplying all labour and T&P for fixing CP Concealed stop cocks polished bright confirming to IS:781-1995 of the following nominal sizes as per specification all complete.

TOTAL PH & SANITARY WORK (C)

Supply and Delivery of OFFICE TABLE - Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS - Table without CPU Hanger size shall be 1500 Width mm x 750 Depth mm x 750 Height mm. Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat (epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat (epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of 3 SEATER WAITING CHAIR - Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS.The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ). The seat has a front water fall edge to provide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. * SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) * BACK SIZE : 41.6 cm (W) x 23.0 cm (H) Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment . Armrest assembly consshould be ts of armrest frame and armrest pad . The armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it should be powder coated ( DFT 40-60 microns ). Armrest pad should be injection molded in Nylon and should be fitted onto the armrest frame complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of RACK -6' X 3' X 18" - Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS. Metal slotted angle rack with self, Powder Coated, 80 Kgs per level complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of GLASS FITTING ALMIRAH Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS.Rigid Knock down construction.Back ,sides and Door are made from 0.7 mm high yield strength CRCA , rest in 0.8 mm CRCA . Sliding door arrangement with top hanging arrangement to prevent derailment. Each Door provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise .5 Lever Cam Lock . Height Wise Adjustable Shelf Mounting , UDL capacity is 40 Kg max. Finish be Epoxy polyester Powder coated thick 50 microns . Screw type leveler with hex plastic base . Metal Top complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of METAL SHOE STAND Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS.Metal Shoe Rack with 5 tier size 120mm Lx450mm Wx1500mm D complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of OFFICE CHAIRS Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS. Mid Back Fabric Ergonomic Chair (Black Ink with White Body)/(Royal Blue with Black Body)/(Milan Red with Black Body), Primary Material Subtype-Glass filled Polypropylene, Upholstery Material-Knitted Fabric complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of Laboratory Work Bench System Laboratory Make: GODREJ/STEELCASE/HERMAN MILLAR OR EQUIVALENT BRANDS. Furniture fusion series uses prime quality CRCA steel for a strong under-structure that can bear the load of heavy laboratory equipement. Its superior powder coated finish makes it resistant to corrosion, which is a common phenomenon in laboratories.Dimensions W x H x D (cm) 396 x 75 x 154 Storage Type A) Under Bench Storage Options - 1. Mobile 2. Suspended 3. Sliding B) Overhead Storage - 1. Wall-Mounted 2. Upright-Mounted Certifications # ISO 13485 : 2016 # ISO 9001 # CE # ISO 50001 # ISO 45001 Delivery Condition Preassembled Warranty 1 Year Reagent Shelf Material 1. Glass 2. Granite 3. Phenolic Resin 4. Metal 5. Epoxy complete in all respect as per the direction of the Engineer-in-Charge.

Supply and Delivery of SS 304 HOSPITAL PASS THROUGH BOX (18X18X18) Inch Make: Aeromech Equipments/SR Air System/Chemietron Clean Tech OR EQUIVALENT BRANDS.The product is manufactured using SS 304 grade stainless steel as per client requirement, and is primarily intended for pharmaceutical industry applications. The size is customizable as per client needs, and the shape is square with a flush door design. It is available as a full stainless steel unit (SS 304 on request) . The unit operates on a voltage of 230 V or 440 V with a frequency of 50 Hz (60 Hz available on request). The weight varies depending on the model and size, and it can function on single-phase as well as three-phase power supply. The surface finishing is SS 304 with a matt finish. It is equipped with a specially designed pass box interlock controller. Parameters such as porosity and noise level are not applicable. Velocity control is available in the dynamic pass box variant. The grade is SS 304, and the model names are SPB and DPB. It comes with an LCD display, and the number of doors can be two or three as per requirement. The unit is lockable, powered by 230 V or 440 V supply, supplied in new condition only, and is manufactured in India.complete in all respect as per the direction of the Engineer-in-Charge.

TOTAL FURNITURE (D)

GRAND TOTAL(A+B+C+D)

Please Enable Macros to View BoQ information