SPL REPAIR TO OR MD ACCN BLDG NO 2-N-5 NZ 227, 228, 229, 230, 231, 232, 240, 243, 246 AND 247 AND PRON OF 01 X ADDL STORAGE ROOM AT CAMP OFFICE OF HQ 165 MTN BDE UNDER GE NORTH BINNAGURI

Amount

Roughening the surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and as directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match complete all as specified and directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in whiter or coloured cement to match as in floor complete all as specified and as directed

M&L for non skid coloured joint free ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but n. exc. 0.38 Sqm as in vertical surfaces of skirting etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor including 10mm thick backing coat in CM 1:4 complete all as specified and as directed.

M&L 75 mm thick PCC 1:4:8 type D2 (Using 40 mm graded stone aggregate) as in sub base of floors as in levelling course for Bath,WC floor below tiles finished even and rough complete all as specified and as directed

M & L for glazed ceramic colour tiles 300X 450 X 7 mm thick as on cup board vertical surfaces of wall such as skirting, dado, riser etc. in Bath, WC and Kitchen set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile approved by Engr-in-Charge, complete all as specified and as directed.

M & L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, Jambs, pillars, window cills, cooking platforms,corner shelf,Flat shelf and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15 mm thick cement plaster (1:4) including rounding the exposed surfaces of granite complete all as specified and as directed

Providing holes to cooking platform of size25 mm dia for inserting cooking gas pipe in suitable place complete all as specified and as directed

Dismantling water tanks and removing to store of capacity exc 500 & n.exc 1000 ltrs. Complete all as specified and as directed.

S & F 500 ltrs rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) incl connecting up pipes securing access covers etc completed all as specified and as directed.

S&F 20 mm dia PVC ball cock (PVC float valves) high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required using reducer and check nut. complete all as specified and as directed

M&L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in water tank platforms, filling and mass concrete. completed all as specified and as directed.

Taking up or down GI 15mm bore pipe and connection including cleaning for refixing or removal from site completed all as specified and as directed.

S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

Refixing old 15mm GI tubing and connections in new or old position (walls, ceiling, floor etc) complete all as specified and as directed. Note: The serviceable G.I pipes obtained from taking down shall be reused.

Taking up or down GI 20mm steel tubing and connections incl cleaning for refixing or removal form site completed all as specified and as directed.

S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

Refixing old 20mm GI tubing and connections in new or old position (walls, ceiling, floor etc) complete all as specified and as directed Note: The serviceable G.I pipes obtained from taking down shall be reused.

Taking down cement plaster on wall & ceiling of any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and as directed.

M&L for (15) mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 5mm) mixed with water proofing compound in top layer 200 ml per bag of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed

M&L 15mm thick rendering in cement mortar 1:6 on fair face of brick work or concrete surface finished fair and even (without using extra cement) complete all as specified and directed.

M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and fair without using extra cement complete all as specified and as directed.

M&L for applying two coats acrylic-based distemper of shade as approved by GE over a coat of primer over two coats of putty surfaces of wall complete all as specified and as directed by the Eng-in-Charge and as per the manufacturer's instructions. Note: 1. Application of new finishes to be carried out mechanically by authorized applicator and as per the manufacturer's instructions.

M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and directed.

Demolition of brick work built in cement mortar of any description complete all as specified and as directed

M & L for brick work with flyash bricks old size bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L brickwork with flyash bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified and as directed.

Supply and fixed in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and as directed.

S & F Vitreous China wash basin, white, flat back, size 630x450mm excluding taps,waste,chain and plug and porcelain stopper but including brackets complete all as specified and as directed.

S&F in repair 10 ltr capacity dual type PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified and as directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rest complete incl provision of cement concrete bedding complete all as specified and as directed

S&F in repairs 15mm bore Bib taps fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete all as specified and as directed

S&F in repairs 15mm bore stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed.

S&F in repair 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed.

S & F in repair 15mm bore PVC Connection with PTMT nut of length 600 mm complete all as specified and as directed

S&F in repair 15mm bore fancy type pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore. complete all as specified and as directed

S&F in repair 15 mm bore angle cock CP with flange complete all as specified and as directed

S&F for brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges. complete all as specified and as directed

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed

S & F Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm embedded in the wall all as specified and as directed.

S&F in repair PTMT towel ring of standard size complete all as specified and as directed.

S&F in repair 1.00 mm thick stainless steel plate rack of size 31"x30"x10" complete all as specified and as directed.

S&F in repair swivel shower of brass CP with shower arm 150 mm size for fixing with 15 mm bore GI pipe complete all as specified and as directed

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed

S &F 32mm Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60gms) complete all as specified and as directed

S& F in repair for 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S & F in repair 40mm dia (HDPE) of pressure rating 6 Kg/f/CM2 fixed complete to walls ceilings or in floors etc complete all as specified and as directed

Taking down CI/PVC/AC soil pipe with fittings from wall, trenches of any description including fittings complete all as specified and as directed

S & F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. complete all as specified and as directed.

S&F 110mm dia PVC bends of any radius/with access door. complete all as specified and as directed.

S&F 110mm dia PVC (SWR) branch piece single (single 'Y') equal or unequal with access door. complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and as directed.

S&F 110mm dia PVC SWR vent cowl complete all as specified and as directed

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls. complete all as specified and as directed

S & F 75 mm bore PVC (SWR) bends of any radius. complete all as specified and as directed

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door. complete all as specified and as directed

S & F 75 mm bore PVC (SWR) branch piece single (Single `Y') equal or unequal with access door. complete all as specified and as directed

Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each and removing from site. complete all as specified and as directed

Refixing shutter of any description but exc 1 sqm and n. exc. 2 sqm each in same opening after easing etc complete all as specified and directed.

S&F for factory made pressed steel frames for doors with one or more rebates including provisioning of necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x60 mm and thickness 1.25mm including one shop coat of priming complete all as specified and as directed.

S&F for pressed steel frames for doors with one or more rebates including provisioning of necessary supply and fixing, lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 105 x60 mm and thickness 1.25mm including one shop coat of priming complete all as specified and as directed.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

S&F 35mm flush shutter, solid core construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rial on either side & as gap insert for top rail & bottom rail: paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing but partly glazed i.e. upper panel will be wire mesh fitted externally in the clear space & lower panel will be plain colour PVC sheet 5mm thick

S& F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S&F 100 mm butt hinges stainless steel complete all as specified and as directed.

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long all as specified and as directed.

S&F aluminium handles 150mm size cast type anodised complete all as specified and as directed.

M&L for Aluminium alloy, anodised sliding door bolt of length 300mm long , with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as Specified and as directed.

M&L for preparation of old wooden surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint complete all as Specified.

Taking down chowkat with shutter n. exc. 1.5sqm each (without taking off shutter from the Frame) complete all as specified and as directed.

S&F factory made single extruded WPC (wood polymer composite) solid door/window/ceosetory windows & other frames/ chowkhat of size 45x85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade) , calcium carbonate and natural fibers (wood powder /rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum , screw withdrawal strength of 2200 N (Face) & 1100 N (Edge) Minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In-Charge (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) complete all as Specified.. Note : For WPC solid door/ window frames minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus sides shall be acceptable but no extra payment on this account shall be made.

S& F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Practical board core complete all as specified and as directed.

S&F in repair stainless steel curtain rod of 25 mm dia and thickness not less than 0.75 mm fixed with curtain rod holder and finials etc. complete as specified and as directed.

S&F 150 mm long Aluminium anodised barrel tower bolts complete all as specified and as directed.

S&F aluminium handles 125 mm size cast type anodised complete all as Specified and as directed.

M & L for providing & fixing factory made solid PVC cup board frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick prelam/plain colour PVC sheet reinforce with 19mm x 19mm MS square tube of 19 gauge thickness throughout the frame and metre cut at two corners and jointed with 2 nos of 150mm long brackets of 15mm x 15mm MS square tubes.The door frame shall be fixed to the wall using 100mm long MS screws through the frame by using PVC fasteners. A minimum 4 nos of screws to be provided for each vertical member and minimum 2 nos of screws to be provided to the horizontal member etc.complete all as specified and as directed

M & L for providing & fixing factory made solid PVC cup board shutter (Flush type) of 24 mm thick made from co-extruded 3 layer rigid PVC foam sheet (single extruded) with density not less than 600kg/cbm outer layer (.8-1mm) thick should be of rigid PVC with density of not less than 1400kg/cbm manufactured byan ISO 9001-2015 certified company. Door should be water proof, termite proof, fire retardant and having good screw holding capacity complete all as specified and as directed.

M&L for providing and fixing factory made PVC shelf/patriation of required size consisting of 20mm thick solid PVC sandwich panel with 1mm thick plain PVC sheet on both sides suitably fixed in complete all as specified and as directed

S&F for 100 mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed

S & F 75mm long Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S & F stainless steel wire cloth 0.36 mm nominal dia wire & average width of aperture 1.40 mm fixed with stainless steel wire staples complete all as specified and as directed

S&F Powder coated aluminium window sliding type three track (2 glazed & one gauzed shutter ) aluminium sections weighing not less than 1.67kg/m for frame and 0.55 kg/m for shutter including necessary jointing cleats, glazing cleats, rubber packing , screws, handle, locking arrangement and 5.5mm thick plain/tinted glass and aluminium mosquito proof gauge including taking down of old existing steel window and making good disturbed surfaces of wall complete all as specified and as directed.

S&F Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surfaces of wall complete all as specified and as directed.

S&F Mild Steel Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for preparation of new or previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new pre-primed steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of Synthetic enamel paint complete all as specified and as directed.

M & L for PCC 1:2:4 type B-I ,(using 20 mm graded stone aggregate) as. in coping /benching to sides of foot path fininished fair and even etc complete all as specified and as directed.

S&F in repair 0.56mm thick plain aluminium sheeting bend to shape fixed with pins to door shutter to prevent water splashing,ridges, hips,valley gutters, drip and straight flashings over crumple joints complete all as specified and as directed.

M & for water proofing treatment to sunken floor with the following course of treatment/ specification: (i) Cleaning top surface of floors /slabs and laying 50 mm thick (avg) PCC of grade M10 (Nominal mix) , mixed with WPC as per manufactrrer's instruction laid in slope 1:20 towards spouts including coveting corners (ii) 15 mm thick plastering in CM (1:4) on sides mixed with WPC as pe rmanufacturer's instruction. (iii) Applying 1st layer of slurry @ 0.488 kg / sqm mixed with acrylic based polymer modified cementious compound @ 0.253 kg /sqm This layer shall be allowed to air cured for 4 hrs. (iv) applying 2nd layer of slurry @ 0.242 kg/sqm mixed with acrylic based polymer modified cementenous compound @ 0.126 kg/sqm.This layer shall be allowed to air cured for 4hrs followed with water curing for 48 hrs.(v) Applying a coat of industrial bitumen 85/25 penetration @ 1.50 kg/sqm on plastered and concrete surfaces (vi) Providing 150 micron thick polyutethene paint in two coats (each of 75 micron measured dry on dry surface over a coat of PU primer including preparation . (Make of PU primer - Dek guard EP -302 of M/S Fosroc or Techno commercially equivalent make as listed in list of makes as approved. (vii) 2 Nos 32mm bore GI medium grade 450mm long spout ,to be provided through external wall to drain out accumulated water.(vii) Sunken floor shall be tested for water tightness by filling water for 72 hrs before and after treatment work is carried out and ensure that no leakage /seepage exists (ix) Sunken portion shall be filled with lean concrete 1:4:8 type D2 .

Demolition of Reinforced cement concrete of roofs,floors(other than ground floors), beams, staircase, landings, chajjas,facia and similar suspended work complete all as specified and as directed

M&L for RCC 1:1.5:3 type A1 using 20mm graded stone aggregate as in chajjas,beam,Column,roof,landing,shelf,plateform,facia and like complete all as specified and as directed

Use & waste of form work to chajjas,facia,Shelf, roof,landing and like for rough finished surface of concrete flat complete all as spd and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil. complete all as specified and as directed

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m depth for foundation, etc., and getting out in soft/ loose soil. complete all as specified and as directed.

Removing excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point. complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils. complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C2(using 40 mm graded stone aggregate) in foundations, filling and mass complete all as specified and as directed.

M & L for preparing of new plastered or unplastered surface of walls and applying two coat of cement base paint over a coat of white wash on plastered surfaces complete all as specified and as directed.

M & L for preparing of new plastered surface or unplastered and applying two coats of acrylic distemper over a coat of primer on wall surface complete all as specified and as directed.

M&L for RCC (design Mix) M-25 as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves etc all as specified and as directed.

M&L for RCC M25 (design Mix) in foundation incl raft ,footings, foundation beams,plinth beams, bases for columns etc basement slabs, underreamed piles & mass concrete complete all as specified and as directed

M&L for RCC M25 (Design Mix) in beams,cantilevers, bressumers, lintels over 1.5 m span etc complete all as specified and as directed

M&L for RCC M25 (Design Mix) in columns,pillars, piers, posts, struts. Etc complete all as specified and as directed

M&L for formwork to concrete foundations, footings, bases of columns, rafts & raft bases , sides & soffits of foundations , plinth beams and similar works in fair finished surface complete all as specified and as directed

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finished surface of concrete complete all as specified and as directed

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc. flat rough finished surface of concrete complete all as specified and as directed

M&L for formwork to sides of pillars, posts, struts, piers, columns etc rough finished surface square, rectangular on plan or polygonal complete all as specified and as directed.

M&L for Hard core, broken boulders to gauge n exc 63 all as spd and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in plinth protection finished fair and even without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 meters and every change of direction and filling the same with & including bitumen and sand 1:3 by weight of grade 'A' complete with and including necessary form work etc complete all as specified and as directed.

M&L for mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips. complete all as specified and as directed.

All as per item No 115 above, but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders

M&L for 75mm thick PCC type C-2 , 1:3:6 (40mm graded stone aggregate) as in sub base to receive new surface all as directed

M&L for 25 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) in under layer to receive flooring complete all as specified and as directed.

S&F of 35mm thick 2nd class hard wood factory made, plain, framed, paneled shutter (two panel) with lock rails and panel of 9mm BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 Part-I klin seasoned and chemically pressure treated.

S&F Aluminium alloy anodised sliding door bolt 250 mm long with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section

S&F150 mm long Mild steel pressed handles, oval type, stove enameled black.

S&F 125 mm Mild steel barrel tower bolts, stove enameled black, with bright bolt and fixed.

S&F steel window with side hung shutters incl. projecting type hinges with steel handles steel peg stay fixing lugs as per drag No CESZ/2018/TD-07, sheet No 1/3 to 3/3 complete with glazing bar 10 cm dovetailed or welded all as spd and as directed.

All as per item No 123 above but without glazing bars complete all as specified and as directed.

S&F of 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as directed.

M&L for 10mm thick screed bed or bedding layer in cement mortar (1:4) mixed with WPC in order to maintain proper slope over existing roof surfaces for laying Water proofing coating, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for waterproofing Coating with polyurethane based water proofing liquid membrane of approved make to be applied by brush with multi coats with minimum dry film thickness of 1mm and shall be cured by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane complete all as specified and as directed. Note: The above treatment will be carried out by authorized applicator of approved firm/company.

ELECTRIFICATION Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for point wiring complete with 1.5 Sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LS (ISI markd) with proper colour coding as earth continuity conductor connected to common earth dolly , modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. all as specified and as directed for the following :- (a) One light point controlled by one way switch 5/6 amps.

(b) All as per item No 129 above but, One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps.

(c) All as per item No 129 above but, One socket out let 5/6 amps point on the independent board

(d) All as per item No 129 above but, One socket out let 5/6 amps point on the same board

(e) All as per item No 129 above but, One bell point controlled by one way switch 5/6 amps.

(f) All as per item No 129 above but, One light point controlled by two way switch 5/6 amps.

All as per item No 129 above but wiring with 2.5 sq mm single core multistranded copper conductor including provision of 2.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) with proper colour coding as earth continuity conductor connected to common earth dolly , for one socket out let 15/16 amps point on the independent board complete all as specified and directed

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, Two way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S&F of Modular bell push, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans,ISI marked complete all as specified and as directed.

S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and as directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and as directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and as directed.

S&F IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified and as directed.

S&F IP 20, Class I, LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified and as directed.

S&F of Bulk head luminaire suitable for 10 Watt LED (or nearest next higher wattage) light IP66 grade, luminaire efficiency not less than 120 lumens/watts with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified.

M & L for sheet metal enclosure fabricated out of 2.0 mm thick CRCA sheet, totally enclosed type, dust & vermin proof, with suitable sized supporting MS angles & suitable openings at top & bottom for entry of outgoing / incoming cables, fixed with nuts & bolts & front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer (spray paint) with minimum dimensions (90 x 75 x 20 cm ) flush to wall for incorporating 01 No TPN DB, 04 Nos electronic meters etc complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, checknuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 3 of SSR Part- I including testing on complete all as specified and as directed.

S & F Modular TV socket, 1 module including 1 module sunken box, back plate and top cover fixed flushed to wall complete all as specified and as directed.

Taking down Electric Meter Single Phase any capacity/size disconnecting electrical connections and refixing the same all as directed.

S&F of switch piano flush type 5/6 amp single pole one way complete all as specified and as directed

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and as directed

S&F of switch socket combination 2 and 3 Pin, 5/6 amps, multipurpose flush non shutter, non inter locking type white ivory finish with and including taking down existing unserviceable complete all as specified and as directed

S&F of switch socket combination 2 and 3Pin, 15 amps, multipurpose flush non shutter, non inter locking type white ivory finish with and including taking down existing unserviceable, complete all as specified and as directed

S&F of deluxe fan electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and as directed

S&F of LED tube fittings 1 x 18/20 watts energy efficient Ts, 230 V incl 1x18/20 watt LED tube, epoxy powder coated CRCA sheet bipin holders, connector block etc, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable complete all as specified and as directed

S&F of decorative wall light fixture made up of polycarbonate suitable for 15 Watt LED retrofit of type B-22 base, IP66 grade, with and including 15 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified and as directed.

S & F energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 25 mm dia 0.90 mtr long bend to required shape complete including removal of old unsv fitting complete all as specified and as directed.

Taking down carefully and refixing only bldg security light of any wattage to its existing place complete all as specified and as directed

Taking down carefully Ceiling fan from its original position and refixing/ hanging after plaster work complete all as specified and as directed

M&L painting of ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc, all as specified and as directed.

Taking down carefully Exhaust fan from its original position and refixing /hanging after B/R plaster work complete all as specified and as directed.

M&L for concealed sub-main wiring along with earth wire of size of 2 x 6.0 sq. mm + 1 x 6.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium sub main wiring all as specified and as directed. Note : Two runs of 6 sqmm conductor for main and one run of 6 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Triple pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators complete with and including taking down old unsv one all as specified and as directed.

S&FMCB distribution boards(DBs) with sheet metal enclosure, doble door,IP43 protection, 240 volts, 8 way single pole and neutral with 200 Amps rated copper bus var (as per OEM), neutral link, earth link earthing studs, suitable for fixing MCBs without MCBs fixed flush to wall/other surface complete all as specified and as directed.

S&F MCB, Triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed.

S&F MCB, Single pole & neutral 32 to 63 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed.

Supply & fix ceiling fans with all accessories 230V, 1200 mm sweep BEE 5 star rated, conforming to IS 374: 1979 complete with pre wired with 3 core cable complete all as specified and as directed

S&F of LED street light luminaires 35 watts IP 66 type incl standard fittings pressure die cast aluminium housing with heat resistant toughened glass housing with epoxy powder coated finish and complete with Electronic driver and all accessories duly prewired and connecting to ceiling Rose with and including GI pipe 32mm dia light grade bend to required shape, clamps, bolts and washers complete all as specified and as directed

S&F sheet metal enclosure for 8 way Distribution Boards (DB's) double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB's/Isolators complete all as specified and as directed

S&F in repair MCB, single pole & neutral, 32 amps, 240 volts, 'c' curve, 10KA all complete with and including taking down old unsv one complete all as specified and as directed

S&F MCB, single pole 6 to 32 amps, 240 volts, 'c' curve, 10KA all complete with and including taking down old unsv one complete all as specified and as directed

Material and labour for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised iron strip25 x 4 mm earth lead by means of nuts, bolts, check nuts and washers including 15 mm bore galvanized iron pipe, light grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, light grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, complete all as shown in electrical plate No 3 of SSR Part-I including testing on complete all as specified and as directed.

Supply and laying cable XLPE insulated screened, PVC bedded, galvanised, steel strip or wire armored, electric power cable, (heavy duty) 1100 volts grade, with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and as directed.

Supply and lay dry river sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top edge of cable after laying complete all as specified and as directed.

Supply and laying sub class B bricks of size 23cmx12.5cmx7.5cm (+/- 10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

M&L for 50mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified and as directed.

SG ENTERPRISE (BID ID -3490665)

NARAYAN MAJUMDER (BID ID -3483872)

L. B. SHARMA (BID ID -3485526)