KARALAM2018-19COMPLETION OF PANCAYATH OFFICE

Amount

OFFICEFABRICATION

50.6.2.2 : Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

10.6.1 : Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

FRONT OFFICE

od177829/2018_2019 : Supplying and erecting plywood table of marine plywood 18mm thick Table [180 x 90 x80] 1 no with one draw with lock and one Door and Key board tray and CPU stand

od182623/2018_2019 : Supplying and erecting cupboard using marine plywood 18mm thick including glass shutter with aluminium frame

MEETING HALL

21.1.1.1 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

od159786/2018_2019 : Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :<br>12mm thick tougheneded glass panes

od192119/2018_2019 : Providing and fixing false ceiling at all heights with gypsum pannel and natural filler false ceiling tiles of Size 595x595<br>mm of approved texture, design and patterns having NRC (Noise Reduction<br>coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85%<br>(minimum). Non combustible as per BS:476 (part-4), fire performance as per<br>BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043<br>W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking<br>metal T-Grid of hot dipped galvanised iron section of 0.33mm thick<br>(galvanized @ 120 grams per sqm including both sides) comprising of main-<br>T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of<br>length 1200 mm and secondary intermediate cross-T of size 24x32 mm of<br>length 600mm to form grid module of size 600 x 600 mm, suspended from<br>ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm)<br>i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully<br>threaded hanger rod upto 1000 mm length and L-shape level adjuster of size<br>85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm<br>of length 3000 mm to be fixed on periphery wall / partition with the help of<br>plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S<br>screws. The work shall be carried out as per specifications, drawing and as<br>per directions of the Engineer-in-Charge.<br>With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.(Modified data-26.22.2)

od192120/2018_2019 : Supplying and fixing at site , aluminium composite panels of alucobound,durabuild or<br>equivalent make and approved colour certified for extior applications,thickness 3mm,with 28 to 30 microns<br>of PVDF coating confirming to ASTM standard on the top aluminium skin of 0.2mm and with a bottom<br>aluminium skin of 0.25mm with service coating of polyeater paint,laminated on to a centre core of 3.5mm of<br>single recycled low density polythylene material.The pannels shall be cut to sizes of required grid<br>dimensions in line with the site conditions.The pannels shall be fixed on pre fabricated frame work using<br>38mm*25mm*1mm thick Aluminium extruded sections of approved make ,joined horizontally and vertically<br>using standard cleats and fastners.The gap of formed between the pannels shall be seated with silicone<br>sealent of dow coring grade 789.The rate inclusive of cost and conveyance of all materials,lead,lift and<br>labour for erection,hire charges for scaffolding etc.complete

9.48.1 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

od193151/2018_2019 : Supplying and erecting platform using marine plywood 18mm thick

NREGS ROOM

od222729/2018_2019 : supplying and erecting tables and shelves using 16mm thick plywood

od222713/2018_2019 : Supplying and fitting 20mm thick ferrocement slabs for partition of shelves including cost of conveyance,labour for fixing,pointing etc complete.<br>

RECORD ROOM

od222713/2018_2019 : Supplying and fitting 20mm thick ferrocement slabs for partition of shelves including cost of conveyance,labour for fixing,pointing etc complete.<br>

21.1.1.1 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionAnodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

21.1.2.1 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium ( anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

PAINTING

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

14.53.1 : Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

14.54.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to an give even shade:One or more coats on old work

Zenith Pius

Bidder Name

M.V. Pius

Zenith Pius