Construction of Mukhya Mantri Lok Bhawan at Jhukhala Dev Block Sadar District Bilaspur HP

Amount

Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work ,pick jumper work , jumper blasting work , soft and hard blasting ,saturated soil , including chiseling or any other mixed variety of soil in all leads dewatering and or removal of slush and other incidentals , including stacking the excavated soil clear from the edge of excavation and than returning the stacked soil in all thickness of layers when required into plinths side of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing from work with steel plates 3.15 mm (three decimal fifteen millimeter ) thick welded with angle iron in frame 30X30X5 mm (thirty into thirty into five millimeters)so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling & removal of same for in-situ reinforced concrete and plain concrete work as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Foundation ,footing basis of columns etc. and mass concrete as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Flat surfaces, such as soffits of the suspended floors roofs , landing and the like floors etc. up to any thickness , all as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Columns, pillars ,posts and struts square, rectangular or polygonal in plan as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Beams cantilever girders and lintels side and soffits of beams, beams haunchings, cantilevers, bressumers and lintels any depth in all heights from floor as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Staircase with sloping or stepped soffits including landing etc. as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Edges of slab and breaks in floor and walls under 20 cm wide as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying, mechanically mixed and vibrated cement concrete 1:6:12 (one cement : six sand twelve graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing as required at site complete excluding the cost of form work but including all leads and lifts of materials in foundation and plinth as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Foundation, footing basis of columns etc and mass concrete as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Suspended Floors , roofs , landings shelves and their supports , balconies beams ,girders, bressumers and cantilever for all floors levels , complete as per direction of the Engineer-in Charge including carriage of material with in all leads ,lifts and other incidentals complete in all respect.

Column , pillars , posts and structs square , rectangular or polygonal in plan as per direction of the Engineer-in Charge including carriage of material with in all leads andlifts and other incidentals' complete in all respect.

Stair case (except spiral cases) including landing but including preparing of the surface and finishing of nosing upto all floor level as required in all leads and lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing tor steel reinforcement for reinforced Cement concrete work including bending ,binding and placing in position and cost of binding wire complete for all floors including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Stone soling/Boulder filling under floors including carriage of material as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work using second Class common burnt clay building bricks, in cement mortar 1:6 (one cement :six sand ) in foundation and plinth including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work using second Class common burnt clay building bricks, in cement mortar 1:6 (one cement :six sand ) in super structure upto all floor levels including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Half bricks masonry using second class common burnt clay building bricks in cement mortar 1:4(one cement :four sand) in super structure up to all floor levels including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing woodwork in frames of doors, windows ,clerestory , windows and other frames wrought,framed and fixed in position .2nd class deodar wood including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

P/F 12 mm thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm thick frame including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing Second class deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws. 40 mm thick including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 40 mm (forty millimeters)thick wire gauge shutters using galvanised M.S. Wire gauge of I.S. Gauge designation 85 (Eighty five ) G. With wire of dia 0.56mm (zero point five six milometers )for doors windows and clerestory windows including bright finished black enameled iron hinges with necessary screw of second class deodar wood including carriage as required with in all leads , lifts and other incidentals, complete in all respect.

Providing and fixing aluminum sliding door bolts and nuts etcetra as per direction of engineer -in- charge including carriage of material within all leads and lifts and other incidental, complete in all respect.

250x16mm (Two hundred fifty into sixteen millimeters)

Providing and fixing aluminum tower bolts with screws etc. Complete as per HP-PWD, Specifidation omplete as per direction of the engineer in charge including carriage of material within all leads and shift and other incidentals, complete in all respect.

250 mm X 10 mm (Two hundred fifty millimeters Into ten millimeters)

200 mm X 10 mm (Two hundred Into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screw etc. complete within all lead and lifts including carriage of material and other incidental complete in all respect.

125 mm (One hundred twenty five milimetre size)

Providing and fixing 200 mm (Two Hundred millimeters) Bright Finished hard drawn hooks eyes including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Kota stone slab flooring minimum size 55x55cm , 20mm thick base of CM 1:4(one cement :four sand) laid over and jointed with gray cement slurry mixed with pigment to match the shade of the slab,including rubbing and granite polishing complete 25mm thick. as HP.PWD specification clause 13 &4.4.1. including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Kota stone slab 25mm thick in risers of steps ,skirting dado and pillars laid on 12mm thick cement mortar 1:3(one cement: three sand) and jointed with gray cement slurry mixed with pigment to match the shade of the slabs including rubbing and granite polishing complete as HP.PWD specification clause 13 &4.4.1including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying full body Duro stone vetrified tiles Simpolo,Nitco ,Kajaria or its equivalant (600x600mmx10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as HP.PWD specification clause 13 &4.4.1 as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying Duro stone vetrified tiles (300x300mmx8mm) Simpolo,Nitco ,Kajaria or its equivalant in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixedwith pigment of required shade to match the shade of tiles complete as HP.PWD specification clause 13 &4.4.1. including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing ceramic tiles of Somany, Nitco ,Kajaria,Orient, Rak,Johnson of size 30x30 cm manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12 mm (twelve millimeter) thick cement mortar 1:3 (One cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles including carriage of material with in all leads lifts in all floors. The sample and pattern of tiles should be got approved from Engineer - in - charge before fixing.

White glazed tile 6 mm thick of Asian/Somany, Nitco ,Kajaria,Orient, Rak, Johnson in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing on wall face PVC (D-plast ) rain water pipes of working pressure not less than 4.50 ( Four point fifty) kg. /per Square metre including filling the joints with approved adhesive complete 100mm (One hundred milimetres) dia pipe as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing cast iron holder bats clamps of approved design to C.I pipe embeded in and including cement concrete blocks, 10 cm10cmx10cm(Ten into ten into ten centimetre)of 1:2:4(One Cement two sand four graded stone aggregate, 20mm nominal size)including cost of cutting holder and making good the walls for 100mm ( One hundred millimeter) dia pipes as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing on wall faces PVC (D-Plast) .accessories for rain water pipes including filling the joints with approved adehsive including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

P.V.C plain bend 100mm (One hundred milimetres) dia pipes.

P.V.C plain shoes 100mm (One hundred milimetres) dia pipes.

Applying priming coat on new wood and wood based surfaces with ready mix paint brushing wood pink primer after and including preparing he surfaces by thoroughly cleaning oil grease dirt an other foreign matter sand papering and knotting etc complete including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Painting two coats (excluding priming coat)on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt dust and other foreign matter send papering and stopping with enamel paint other than white including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 0.60mm ( Zero point sixty millimeter) thick pre-painted steel sheet of TATA/ /DUROSHINE in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 ( Twenty ) micron over 5 ( Five ) miocrons primer coating to back coat of polyster of 5 ( Five ) microns over 5 ( Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts , 6mm diametre with prepainted limpet and rubber washers complete with all accessories including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm. (Sixty centimetres)overall with 0.60mm ( Zero point sixty millimeter) thick prepainted steel sheets TATA/ /DUROSHINE in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyester organic coating of 20( Twenty ) microns over 5 ( Five ) micron primer coating + back coat of polyster of 5 ( Five) microns over 5 micro primer coating including fixing with prepainted iron, J or L hooks bolts and nuts ,6mm(Six milimetre) diametre and prepainted G.I limpet and bitumen washer complete with all accessories including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Steel work welded in built up sections, trusses and framed work, including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

In Trusses and trussed purlins in building .

In gratings framed guard bars,ladders,railling,brackets and similar works

6 mm (six millimeter)thick cement plaster to ceiling in cement mortar 1:3 (one cement :three sand as per direction of engineer-in- charge including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

15 mm(fifteen milimetres) cement plaster in single coat in cement mortar 1:6 (One cement :six sand) on the rough side of brick/ concrete/ stone walls for interior plastering upto all heights including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finishing even and smooth as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

15mm(fifteen milimetres) cement plaster in cement mortar 1:6 (One cement :six sand) in single coat on fair side of brick/ concrete/ stone walls for interior plastering upto all heights including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finishing even and smooth as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Distempering (two coats ) with oil bound washable distemper of approved brand and manufacture and required shade on un-decorated wall surfaces to give an even shade over and including a priming coat with alkali resistance primer of approved brand and manufacture after thoroughly brushing surface free from mortar dropping and other foreign matter and also including preparing the surfaces even and sand papered smooth priming coat with distemper primer with in all leads lifts carriage of material and other incidentals complete in all respect.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing plinth protection 50 mm (Fifty Millimeters )thick in cement concrete 1:3:6 (one cement :three sand :six graded/ crushed stone aggregate 20 mm nominal size including finishing the top surface of concrete smooth finfish ,as per direction of the Engineer-in- charge of material with in all leads , lifts & other incidentals’

Providing under layer for plinth protection of 75 mm (seventy five millimeters ) thick (unconsolidated ) bed of dry brick /stone broken/crushed aggregate 40 mm (forty millimeters ) nominal size well rammed & consolidated & grouted with fine sand including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Constructing Coursed rubble hammer dressed 'U' shape open surface drain with side wall. 15 X 23 cm (Fifteen into twenty three centimeter ) in cement mortar 1:6 ( One Cement : Six approved Sand) and inside plastering with cement mortar 1:3 (One Cement: Three approved Sand) including earth work and laying 10 cm (Ten Centimatre ) cement concrete in 1:5:10 (One Cement : Five approved Sand : Ten graded crushed stone aggregate) of 40 mm (Forty millimetres) nominal size and 7.5 cm (seven Point Five Centimatre ) cement concrete 1:2:4 (One Cement : Two approved Sand : Four graded crushed stone aggregate of 20 mm (Twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Excavation in drains and channels etc. in earth work including dressing of side and bed and disposing of excavated earth upto any lead and lift all disposed earth to be levelled and neatly dressed: Pick jumper work including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying in trenches galvanised mild steel tubes 25 mm (Twenty milimeter) ( Medium grade )tube fittings (earth work in trenches to be measured and paid separataly) including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes 25 mm (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

15 mm nominal bore .

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes completeas required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC water storage tank of ISI : 12701 marked , G.I. inlet and outlet connection , 15 mm ( Fifteen millimeter) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground lavel as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

500 (Five hundrd ) litres net capacity tank .

1000 (One thousand ) litres net capacity tank .

Providing and fixing PVC Finolex plain bend ISI marked including fixing with approved adhesive etc. completeas required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

For 110 mm nominal size

Providing and fixing PVC Finolex single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC Finolex door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC Finolex double equal branch with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc in all respect as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC Finolex plain double equal branch ISI marked including fixing with approved adhesive etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC collers ISI marked including fixing with approved adhesive etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

For 110 mm size

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

110 mm X 90 mm.

Providing and fixing PVC cowl fixing with approved adhwssive complete. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

100 mm ( One hundred millimetres) nominal size

Providing and fixing PTMT grating round of approved quality and colour 100 mm nominal dia. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing vitreous China wash down,water closet squatting pan (Indian type W.C pan) size 580mm CERA/HINDWARE/NEYCER/SANITARYWARE (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Orrissa Pattern

Providing and fixing PVC Finolex 'P' or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately): as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Angle Indian Universal closet

Providing and fixing PVC Coloured / white high density polythelene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern COMMANDER/ CORAL l/CERA /HINDWARE /HINDUSTAN with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float,with push button,couplings for connections with inlet, outlet and ovr flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers : Solid type.as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

white plastic seat and cover

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube. as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings. Flat back as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

550 mm x 400 mm .

Providing and fixing C.P brass waste for wash basin/sink 32 mm dia ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing M.I. union for wash basin/sink 32 mm dia. ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing PVC connedtion with brass union 15 mm nominal bore. 32 mm dia ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600x450 mm belevelled edge mirror of superior glass moulded on 6 mm thick A.C. sheet or ply wood and sheet and fixed to wooden plug with CP brass screws and washers ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass towel rail complete with C.P. brackets fixed to wooden plugs with C.P. brass screws 600 mm x 20mm ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass bib tap with capstan head 15 mm dia meter ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass Pillar tap bib tap with capstan head 15 mm dia meter ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass stop cocks 15 mm dia meter ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass angle valve without nuts and pipes . 15 mm dia meter ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing . brass valve (Horizontal plunger) . 15 mm dia meter ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260mm x 350 and 340x430x265mm sizes, respectively with authomatic flusing cistern with fittings R.S or C.I. Brackets standard size galvansied steel flush pipe and spreaders galvanised steel flush pipe and spreaders with brass unions and G.I. clamps complete, inciuding painting of cistern and fittings, cutting and making good the walls floors ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

one urinal basin with 5 litres C.I. automatic flushing cistern.

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Constructing man hole with RCC top slab 1:2:4 mix in (One cement:Two sand:Four graded stone aggregate 20mm (Twenty millimetre nominal size foundation concrete 1:4:8(One cement::Four sand:Eight graded crushed stone aggregate 40mm (forty millimetre) nominal size inside plastering 15mm(Fifteen millimetre) thick with cement mortar 1:3(One cement: Three sand) finished with a floating coat of neat cement and making channel in cement concrete 1:2:4 mix (One cement:Two sand:Four graded crushed stone aggregate 20 mm (Twenty millimetre) nominal size finished smooth complete curing and testing Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg . (weight of cover 23 kg and weight of frane 15 kg.) ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Constructing brick masonry chamber for under ground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (1 cement : 5 sand ) C.I. Cover with frame (lightduty ) 355mm x 610mm internal diamensions total weight of cover with frame to be not less than 38kg (weight of cover 23 kg. and weight of frame 15kg) R..C.C top slabe with 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:5:10 ( 1cement : 5 sand : 10 graded stone aggregate 40mm nominal size) inside plaster 15mm thick with cement mortar 1:3 (1 cement : 3 sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. ncluding carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Inside dimensions 455 mm x 610 mm x 450 mm deep single pipe line.

NITESH GARG

Ramesh Chand Govt. Contractor

Mr. Sohan Lal

Ranjeet Thakur

MANISH KUMAR

Neeraj Sharma