SPECIAL REPAIRS TO ROOF OF BUNGLOW NO-5 AND CONNECTED MISC WORK AT LANCER LINES,

Amount

NOTE : Tenderer advised to visit Bldg as the buildng is heritage buildng having height more than normal height .

Demolition of Brickwork or stone/boulder masonary built in cement or cement lime mortar including all quoins, arches,pillars etc. complete all as specified and directed.

M & L for Brickwork with subclass 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks built in CM (1:4) straight or curved on plan to any radius in half brick thick walls

Taking down cement plaster from brick/concrete surface including raking out joint hacking for key scrubbing down with water etc complete.

M&L for 15 mm thick rendering in CM 1:6 on brick work or concrete surface on wall finished even and smooth without using extra cement complete.

M&L for 15mm thick rendering in two layer on brick work or concrete surface of wall, 5mm thick plaster in CM:1:4 mixed with WPC @ 3% by weight of cement surface finished even and even over 10mm thick plaster in CM 1:6 complete. (Note : WPC shall be measured & paid separately)

Supply only water proofing compound.

M&L for rendering 10mm thick on brick or concrete surface of ceiling in CM 1:3 surface finished even and smooth without using extra cement complete.

M&L for preparation of new plastered surface of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer including1 to 1.5mm thick wall care putty on wall complete

M&L for prepartion newly plastered surface of ceiling and applying three coat of white wash complete.

M&L for prepartion old plastered surface of ceiling and applying a coat of white wash complete.

M&L for prepartion of newly plastered surface of wall and applying Two coats of weather proof paint on external surfaces over a coat of alkaline resistant primer complete.

M&L complete removal of existing treatment on wall surface and applying Two coats of weather proof paint on external surfaces complete.

M&L for complete removal of exisiting treatment on wall surface and apply two coat of oil Bound distemper over and including 1 to 1.5mm thick wall care putty complete

M&L for preparation of new steel surface of any description not otherwise descsribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete.

M&L for preparation of old steel surface of any description not otherwise descsribed over 10 cm width or girth and applying one coat of synthetic enamel paint .

M&L for preparation of new wooden surface of any description not otherwise descsribed over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete.

M&L for preparation of old wooden surface of any description not otherwise descsribed over 10 cm width or girth and applying one coat of synthetic enamel paint

Raking out joints / pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs, etc. and M&L for keyed pointing to brick walls in CM 1:3 complete all as specified and directed.

M&L for 18 to 20 mm thick machine cut Green Marble work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shadeover and including screed bed15 mm thick CM 1:6 complete

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n.exc.4 Sqm each

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) area n.exc. 1.5 Sqm each

M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type veneered both side with decorative choice lamination type 1 (factory laminated),including 6mm thick external teak wood lipping fixed with nails, color and pattern as approved complete.

M&L 35mm thick 2nd class hard wood (factory made) glazed and skeleton shutters, open rebated and prerpared to receive glass, gauge, etc edges of trimming plain chamfered or rounded fitted with cut and metered beads for securing/ gauge etc sizes of members of shutters as specified in SSR Part-I Section 8.20 (a) complete.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing and matching with door shutter shade. The door frame shall be tied to the wall using 75/100mm long MS screw complete .

S&F 30mm thick factory made both sides prelam panel PVC door shutter consisting of frame made out of MS tube of 19 gauges thickness and size 19mm x 19mm for stiles, top and bottom rails, MS frame shall have a coat of steel primer of approved make and manufacture. MS frame shall be covered with 5mm thick heat moulded prelam PVC C channel size 30mm thickness, 70mm width, out of which 50mm should be flat and 20mm shall be tappered in 45 degree < on either sides forming stiles and 5mm, 95mm wide prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide. prelam PVC sheet out of which 75mm shall be flat and 20mm shall be tappered on both sides to form lock rail. Top rail, bottom rail and lock rail shall be provided either sides of the panel 10mm (5mm x2) thick 20mm wide cross PVC sheet shall be provided as gap insert for top rail, and bottom rail paneling of 5mm thick both side prelam PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with 7mm (5mm+2mm) thick 15mm wide. PVC sheet beading on inner side and jointed together with solvant cement adhesive, an additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of C channel using PVC solvant adhesive etc. complete.

Providing and fixing factory made 18(+0.7mm) thick PVC sheet one sided pre laminated sheet cabinet shutter. 18 mm(+0.7mm) thk sheet shutter of density 600 kg/m3 bent at 90 degrees and finished all edges at all level for making edges, Lipping/bending or 0.5 mm thk PVC sheet lipping at all four edges using bonding tape etc complete all as per directions of engineer in Charge & Manufacturers's speciifcations.

M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/PVC door frame with screw complete.

S&F 300 mm aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and staples complete.

S&F aluminium alloy handle 150 mm cast type anodised complete.

S&F 150 mm aluminium anodised barrel tower bolts of extruded section and fixed complete.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring etc,overall length of cover plate 150 mm complete

M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand and similar work con- forming to Fe.290.Gde-E-165 complete

S & F for pressed steel doors frame (Thickness of MS sheet 1.25mm) with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, stainless steel hinges, lock strike plate, etc., complete, as specified and as directed. Note :- Filling of hollow of frame with plain cement concrete and stainless steel hinges will be measured and paid saperately under respective items.

S & F for pressed steel doors frame with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, stainless steel hinges, lock strike plate, etc., complete, as specified and as directed. Note :- Filling of hollow of frame with plain cement concrete and stainless steel hinges will be measured and paid saperately under respective items.

S&F Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. Complete

S&F of Powder coated aluminium window/ventilator shutters, side hung/sliding type, including necessary joining cleats, sash bars, glazing clips rubber neoprene packing, anodised aluminium snap beading, screws etc as per manufactures instruction & trade pactice.

S&F sheet glass 4 mm thick oridinary quality and glazing with rubber packing to windows/ventilators in square n exceeding 0.50 sqm in each pane complete.

S&F figured glass 4 mm thick pin headed type and glazing with rubber packing to windows/ventilators in square not exceeding 0.50 sqm in each pane complete.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

M & L for cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in filling hollow portion of pressed steel door frame

S&F in repair 20mm dia stainless steel fancy type curtain rod including brackets, etc. as directed

Dismantling of Asbestos Cement (corrugated, semicorrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof ridge covering/cladding to wall, fixed with self tapping screws as specified

Dismantling of framed timber scantlings 40 sq.cm and over in section, in any position complete all as specified and directed

M & L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240 complete all as specified and directed.

S&F plates, (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde- E- 250) quality- A with reveted bolted or welded attachment all as specified and directed.

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions

Dismantling of boarding, any description, fixed in any position with nails,complete all as specified and directed.

S & F 12mm thick medium density fibre board, exterior grade, fixed to timber framework with screws as in Eaves including fitting complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including wilding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on top of floor or the side of waist slab with suaitable arrangement complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded aggregate) and finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M & L for Forming 65mm deep x 10mm thick contraction (dummy joints), filled with sealing compound grade "A".

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for RCC M 15 (nominal mix)type B1,1:2:4 ( 20mm graded stone aggragate) for beams, cantilevers, bressummers lintel over 1.5 mtr span etc complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams,beam haunchings, girders, bressummers, lintels, cantilevers, shelves etc. rough finished surfaces of concrete flat, complete all as specified and directed.

M&L for TMT steel bars in reinforcement 10mm dia and over cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for TMT steel bars in reinforcement 5mm dia and over as in stirups cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for vitrified Ceramic tiles, light shade 10mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15mm thick in cement mortar1:6 all as specified.

M&L for Non-skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in cement mortar1:6 all as specified.

M&L for Glazed ceramic coloured tiles in vertical surface (300 x 200mm) x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including screed bed 10mm thick of cement mortar1:4 all as specified.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth for bore of pipe 15/20 mm complete

S & F in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mmincluding suitable waste coupling and waste pipe.

Taking up or down steel tubing and connections, 15mm bore including cleaning for refixing or removal to store

Taking up or down steel tubing and connections, 20mm bore including cleaning for refixing or removal to store

Taking up or down steel tubing and connections, 25mm bore including cleaning for refixing or removal to store

Supplying and laying of 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Dismantling of cast iron or reinforced concrete drain pipes up to 100 mm dia jointed in cement mortar from wall or taking out of trenches, if required

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls

S&F in repairs 60cm long CP Brass 20mm dia tubular towel rail with flanged. ends.

Supply hoisting and fix in repairs1000 ltrs rotational moulded polythene water storage water tanks twin layered construction ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I duly ISI Marked, 20mm GI light grade over flow pipe approx length 1.5m long, 20mm GI medium grade pipe for wash out approx length 2.00 m duly plugged at one end shall be provided including dismantling the existing tank complete all as specified.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern) including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devicecomplete all as specified and directed.

S&F in repair 15 mm bore ball valves, high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210gms) complete all as specified and directed.

S7F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair vitreous china Wash hand basin, white , flat back size 550x400 mm except taps but incl brackets and 32 mm dia CP waste coupling all as specified.

S&F in repair CP Grating of size 150x150 mm complete all as specified and directed.

S&F in repair 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F in repair PVC connection pipe 15mm dia and 600 mm long with two PTMT nuts at each ends with rubber washer

S&F 15mm dia stop cock,cast copper alloy, fancy type cromimum plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedcomplete all as specifed and directed.

S&F Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union

S&F in repairs 10 Litres, PVC valveless syphonic action type, flushing Cistern, low level, white, inlet, ball valve, float, and brackets inclluding 32mm PVC flush pipe suitable for flushing cistern complete.

S&F Toilet paper holder of stainless steel fixed to walls with chromium plated (CP) brass screws

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F in repair CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed.

S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed.

S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed.

S & F 110mm PVC (SWR) junction single, (Single T, 'Y' type) equal or unequal all as specified and as directed.

S & F 75mm PVC (SWR) junction single, (Single, 'Y' type T) equal or unequal all as specified and as directed.

S&F in replacement 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in replacement PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F in replacement PVC 'P' trap all as specified and as directed.

S&F in repair Chromium plated long body fancy type bib taps with wall flange, cast copper alloy with round operating knob screwed down high pressure, screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repair 15mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair CP wall mixer with all fittings complete all as specified and as directed.

M & L for stainless steel spring type hinges of heavy grade suitable for cabinet shutters fixed with wooden frame.

M & L for stainless steel handles decorative type of approved pattern of size 125 mm. All as specified and directed.

M & L for stainless steel handles decorative type of approved pattern of size 75 mm. All as specified and directed.

M & L for basket for kitchen cabinets made out of stainless steel SS 304 grade ,fixed in position with stainless steel screws etc on channel guides of different sizes as follows and as per sample: -

(a) for dishes

(b) for large plates

(c) without shelves

(d) For bottles etc.

M & L for stainless channel rails with ball bearing for the sliding drawers of kitchen cabinet baskets of various depths all as specified and ditected

Demolition of existing PCC /lean concrete including floor tiles and removing rubbish off the premises.

M&L for sunken portion filled with lean concrete 1:5:10 using aggregate and finish the surfaces rough to receive sub base complete.

M&L for 25 mm thick cement concrete in flooring type B0, 1:2:4 (12.5mm graded aggregate) with water proofing compound @3% by weight of cement for laying floor tiles complete. Note (WPC will be measured and paid separately).

M&L for 15 mm thick plaster in sunken portion with CM 1:3 mixed with water proofing compound @2% by weight of cement plaster surface should be even and smooth without using extra cement . Note . (WPC will be measured and paid separately).

M&L for providing & laying APP based polymeric membrance of weight of 3 kg/sqm with non woven polyster fibre as reinforcement over a coat of bituminious/polymerized primer confirming to IS-3384 @ 0.30 Ltrs/Sqm by torch application with side over laps & longitudinal joints over laps etc as per manufacturer instructions complete.

Surface excavation n.exc (not exceeding) 30 cm deep and averging 15 cm deep deep and getting out in soft/loose soil

Hardcore of gauge n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to true surface of broken stone or boulders.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M&L for100 mm thick plain cement concrete type D-2, 1:4:8 using 40 mm graded aggregate as in subbase

M & L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 grade with Grey cement and no pigment over and including 30mm thick Sand filling as sand cushioning spread and levelled complete all as specified

Removing excavated material exc 250 m but n. exc 500 m and depositing where directed at a level n.exc 1.5 m above the starting point

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.(kerb stone size40x40x15cm)

Taking down carefully copper / Aluminium point wiring including (light, fan, socket or power complete fittings, such as switches, ceiling roses, pendant holders, Batten holders, shades conical fan regulators, light or power sockets etc) removing materials from site and making good disturbed surfaces of walls roofs etc all as directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

M & L for concealed point wiring complete with multistranded copper conductor (FRLS)1.5 Sqmm size PVC insulated unsheathed cable 1100 volt grade, conforming IS 694 & color code in conduit system of wiring, drawn in including PVC conduit not less than 20 mm dia concealed duly fixed with U-Clips, including cutting chases, finising of slote by means of cement mortor making good to the existing surface of the wall & touching with the existing colour of wall with three coats and making good disturbed surface complete, sunk in pressed steel terminal boxes of required size not less than 1.2 mm thick factory made and factory painted with top cover 3 mm thick plastic laminated sheet fixed with brass screw and washer with all accessories including single core multistranded copper conductor 1.5 sqmm size solid PVC insulated unsheathed cable (FRLS) as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified.

One light point controlled by one one/way switch.

One Fan point controlled by one one/way switch.

One 3 pin 5 Amps socket outlet on same board with other switch.

One 3 pin 5 Amps socket outlet on independent board

One light point controlled by two way switches

One bell point controlled by one way switches

All as per item No. 129 above but using 2.5 Sqmm PVC insulated, unsheathed cable for one 3 pin socket outlet 15 Amps on independent board

Taking down U/S FTL and Supply and fixing of 4' 18W LED Tube With Batten with system lumen output of 1800 lumens. System Efficacy should be > 115lm/ W. The Luminaire Should have Cool Daylight Color temp of 6500K & CRI>80.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Surge Protecton of 3KV.All the Photometrical & Electrical parametrs must be supported by LM79-08 test report from NABL Accridiated LAB OR UL, R9 Value > 0. Lamp starting time is not more than 1 Sec. The LED tube light conforms to applicable IS.Make of LED From Philips/Crompton/ Wipro. Housing of Batten should be made from Single piece powder coated CRCA sheet steel.Similar to Crompton LDSL 18-CDL with Master TLED 18W 1800 Lumens.

Supply,Testing & Commsioning of IP66 & IK09 integral LED Bulk Head luminaire with housing made of Pressure Die Cast alumunium & Optical cover made of Opal Polycarbonate for glare free lighting . System Lumen Output of minimum 600 lumens. Power Consumption should not exceed 10W (Including Driver Loss). For Glare free lighting luminaire should be with Opal diffused Polycarbonate. including & connecting with 0.5 sqmm PVC insulated overall PVC sheathed 3 core flexible cable complete with all other accessories & all as specified & directed.

S/F Modular switch 1 way 6A, 1module Make : Anchor/SSK/CONA

S/F Socket, 6A - 2/3 pin combined 2module, ® Make Anchor/SSK/CONA or its equivalent.

S/F Socket 6A/16A - 2/3 pin combined 2 module, ®. Make Anchor/SSK/CONA or its equivalent.

S&F Modular Bell push 6A 1 module Make Anchor/SSK/CONA or its equivalent.

S & F Bell ding dong type, one way, 240 volts, AC, ISI marked.

S/F ceiling rose surface bakelite three terminal 65 x 50 mm three terminal 250/230 volts ISI marked. Make : Legrand/Polycab

S&F Fan step regulator, 120W - 2 module Make Anchor/SSK/CONA or its equivalent.

S&F Modular White cover plate with frame,1 module

S&F Modular White cover plate with frame,2 module

S&F Modular White cover plate with frame,4 module

S&F Modular White cover plate with frame, 6 module

S&F Modular White cover plate with frame,8 module

S&F Modular Metal flush box 1/2 module

S&F Modular Metal flush box 4 module

S&F Modular Metal flush box 6 module

S&F LED Panel 2'X2' Ultra slim Light fitting 36w

Supply and fixing in repair ceiling fan 1200 mm sweep BEE 5 star rated including fixing of down rod and connection complete with & including provision of flexible three core PVC insulated multi-stranded copper conductor cable of size 0.50 sq mm from ceiling rose/connector to fan complete all as specified and directed. Note: Old UNSV ceiling fans will be deposited to AGE E/M office

S & F MCB SPN 32 Amps 10 KA rupturing capacity.

S&F MCB SP 5 to 40 Amp 240 Volts

S/F in repair sheet metal enclosure for single pole and neutral 12 way 240 voilts, 100 Amp rated bus bar. IP 43 - IK -09 CAT No. 6077 11 of Make Legrand or its equivalent in Schnieder/ABB.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single MCB SP 20 Amps. Make Legrand or its equivalent in Schnieder/ABB.

Earthing complete as per electrical plate NO.5 of MES SSR Part I with galvanised steel plate earth electrode 600 mm x 600mm x 6 mm burried directly in ground in a pit of depth not less than 2.25 metre below ground level with the top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to and incl galvanised iron or steel earth lead wire 4 mm dia by mneans of bolts, nuts, check nuts and washers of galvanised iron or steel earthing wire protected by galvanised iron or steel pipe 15 mm dia light grade and connected to main switch board or main control board watering pipe shall be 20 mm dia GI medium grade incl excavation and earth work in any type of soil strata, PCC pit, CI Frame, RCC covers complete.

S & F in repair wall security light LED type complete with GI bend 1.2 mtr and fixing on wall/pole with clamp, nut & bolt complete all as directed and specified by Engr-In-Charge. CAT Part No.LSTO-25-CDL 25watt of Make CG or its equivalent in other makes specified

S & F lamp holder for LED bulb PVC/Polycarbonatetype with cord grip including Supply and fixing of of 7 W LED Bulb with system lumen output of 600 lumens. System Efficacy should be > 85lm/ W. TheLamp Should have Cool Daylight Color temp of 6500K . Lamp should be supplied with E27 Holder. Similar to Philips Ace Saver.

S&F of Exhaust fan 300 mm sweep 1250 RPM with minimum airflow/air delivery 720 Cmh, 06blades, light weight, rust proof body & blades, self opening louvers for protection from birds & rain water, IP-55, 230 Volt AC supply, rated power input not more that 45watt, connecting up including provison of cable from ceiling rose to fan.

Supply, Fixing, Testing & Commisioning of 2' 10W Mirror LED Batten with system lumen output of 1000 lumens. System Efficacy should be > 85lm/ W. The Luminaire Should have Cool Daylight Color temp of 6500K & CRI>80.Life 40K burning hrs with 70% lumen maintenace. PF>0.95 Housing of luminaire should made of die cast alumunium & mounting on two PVC square boxes of size not less than 75mm X 75mm complete including connecting fitting with not less tha 0.5 sqmm 3 core flexible stranded copper conductor wire upto ceiling rose complete all as specified & directed.

M & L for sub main wiring (on surface conduit) using two single core 4 Sqmm fire retardant PVC insulated and unsheathed cable with copper conductor 1100 volts grade ISI marked drawing in and including accessories like bends, tee, etc fix on wall and ceiling and connecting to earth dolly and including 4 Sqmm earth wire, PVC insulated & unsheathed all as directed including taking down existing submain wiring(Three runs of 4 sqmm wire including conduit shall be measured as one length).

Aditya Construction

Badri Electricals