REPAIR AND MAINTENANCE OF PUMPING MACHINERIES CLEANING OF UG SUMP OH RESERVIORS AND MAINTENANCE OF AMF PANELS FIRE FIGHTING ETC UNDER GE I NAVY JAMNAGAR

Amount

Excavation in trenches and not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation of drain, man hole, laying of cables, stay etc. not exceeding 10 Sq. m on plan and not exceeding 1.5 m depth and getting out in soft / loose soil.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soil complete all as specified and directed.

Removing excavated surplus soil to a distance not exceeding 50 mts and depositing where directed .at a level not exceeding 1.5 M above the starting point complete all as directed.

M&L for PCC 1:3:6, type C1 (using 20 mm graded crushed granite stone aggregate) as in coping including necessary form work complete all as directed.

M&L for brick work with fly ash bricks, straight or curved on plan exceeding 6 m mean radius built in CM 1:4 complete all as specified including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris to a distance not exceeding 50 mts and depositing where directed.

M&L for rendering 10 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even and finally apply three coats of white wash on plastered surface complete all as directed. Note: Quoted rate shall deemed to be inclusive of three coats of white wash.

M&L M-35 grade, 60 mm thick PVC moulded machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment conforming to IS: 15658-2006, laid over and including 40 mm thick compacted sand cushion as per manufacturer's instructions complete all as directed..(Note : Quoted rate is deemed to be inclusive of sand cushoining).

Taking down/up the existing submersible pump set of capacity 3 to 5 HP from underground sump, well, transporting to work shop, dismantling the submersible pump set, cleaning descaling and re-assembling after repair/ replacement of spare parts including taking out pipe, cable etc. and lowering, fixing at the same/ new location complete all as directed. Note: Cost of new spare parts and rewinding shall be measured and paid separately under relevant items of BOQ under .

All as per item No. 8 here in above, but for 7.5 to 10 HP. Note: Cost of new spare parts and rewinding shall be measured and paid separately under relevant items of BOQ under .

All as per item No. 8 here in above, but for 15 to 25 HP. Note: Cost of new spare parts and rewinding shall be measured and paid separately under relevant items of BOQ under .

All as per item No. 8 here in above, but for 30 HP. Note: Cost of new spare parts and rewinding shall be measured and paid separately under relevant items of BOQ under .

Supply only new Pump Shaft for 3 to 5 HP of submersible pump and motor as per existing type.

Supply only new Pump Stage CI thrust for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Pump stage CI thrust casing for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Cast Iron impeller for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Neck ring brass for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Pump Rubber bush for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Pump metal bush for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new SS sleeves for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Pump cupple for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new pump key stage wise for 3 to 5 HP of submersible pump and motor as per existing type.

Supply only new motor bush for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new shafting turnning and granding for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new CI thrust bearing for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new CI stage casing for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new Motor cupple for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new motor upper housing for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new motor lower housing for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new motor base thrust cover for 3 to 5 HP submersible pump and motor as per existing type.

Supply only new motor and pump connecting piece for 3 to 5 HP of submersible pump and motor as per existing type.

Supply only new Pump Shaft for 7.5 to 10 HP of submersible pump and motor as per existing type.

Supply only new Pump Stage CI thrust for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Pump stage CI thrust casing for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Cast Iron impeller for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Neck ring brass for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Pump Rubber bush for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Pump metal bush for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new SS sleeves for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Pump cupple for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new pump key stage wise for 7.5 to 10 HP of submersible pump and motor as per existing type.

Supply only new motor bush for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new shafting turnning and granding for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new CI thrust bearing for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new CI stage casing for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new Motor cupple for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new motor upper housing for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new motor lower housing for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new motor base thrust cover for 7.5 to 10 HP submersible pump and motor as per existing type.

Supply only new motor and pump connecting piece for 7.5 to 10 HP of submersible pump and motor as per existing type.

Supply only new Pump Shaft for 15 to 25 HP of submersible pump and motor as per existing type.

Supply only new Pump Stage CI thrust for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Pump stage CI thrust casing for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Cast Iron impeller for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Neck ring brass for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Pump Rubber bush for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Pump metal bush for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new SS sleeves for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Pump cupple for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new pump key stage wise for 15 to 25 HP of submersible pump and motor as per existing type.

Supply only new motor bush for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new shafting turnning and granding for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new CI thrust bearing for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new CI stage casing for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new Motor cupple for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new motor upper housing for 15 to 25 submersible pump and motor as per existing type.

Supply only new motor lower housing for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new motor base thrust cover for 15 to 25 HP submersible pump and motor as per existing type.

Supply only new motor and pump connecting piece for 15 to 25 HP of submersible pump and motor as per existing type.

Supply only new Pump Shaft for 30 HP of submersible pump and motor as per existing type.

Supply only new Pump Stage CI thrust for 30 HP submersible pump and motor as per existing type.

Supply only new Pump stage CI thrust casing for 30 HP submersible pump and motor as per existing type.

Supply only new Cast Iron impeller for 30 HP submersible pump and motor as per existing type.

Supply only new Neck ring brass for 30 HP submersible pump and motor as per existing type.

Supply only new Pump Rubber bush for 30 HP submersible pump and motor as per existing type.

Supply only new Pump metal bush for 30 HP submersible pump and motor as per existing type.

Supply only new SS sleeves for 30 HP submersible pump and motor as per existing type.

Supply only new Pump cupple for 30 HP submersible pump and motor as per existing type.

Supply only new pump key stage wise for 30 HP of submersible pump and motor as per existing type.

Supply only new motor bush for 30 HP submersible pump and motor as per existing type.

Supply only new shafting turnning and granding for 30 HP submersible pump and motor as per existing type.

Supply only new CI thrust bearing for 30 HP submersible pump and motor as per existing type.

Supply only new CI stage casing for 30 HP submersible pump and motor as per existing type.

Supply only new Motor cupple for 30 HP submersible pump and motor as per existing type.

Supply only new motor upper housing for 30 submersible pump and motor as per existing type.

Supply only new motor lower housing for 30 HP submersible pump and motor as per existing type.

Supply only new motor base thrust cover for 30 HP submersible pump and motor as per existing type.

Supply only new motor and pump connecting piece for 30 HP of submersible pump and motor as per existing type.

M&L cutting out the burnt winding of all the three phases of stator, for submersible pump set of capacity 3 to 5 HP, taking out burn out copper wire by cleaning the slots properly, re-winding the three phases with original gauge, super enamaled the copper winding wire including insulating material i.e. varnishing, cotton tape, insulating paper, sleeves drying the winding with required temperature re-assembling the rotor and stator after cleaning and dusting of rotor to remove the settled dust particles complete all as directed.

All as per item No. 88 here in above, but for 7.5 to 10 HP

All as per item No. 88 here in above, but for 15 to 25 HP

All as per item No. 88 here in above, but for 30 HP

Disconnecting the single stage split casing centrifugal pumping set / Monoblock pumping set, 60 HP (any make), separating from sunction, delivery pipeline, electrical connection etc. dismantling the same including transporting to civil workshop(without any extra cost to Govt) for overhauling, repairing and replacing the unserviceable spare parts such as gland, packing, bearing bush, washer etc. Painting with one coat of synthetic enamel paint with proper colour codes and writing letters of SM No. and MES No. etc. and installing, making connection suction and delivery side with necessary new packing material, nut bolt etc. complete all as specified and as directed.

All as per item No. 92 here in above, but for the single stage split casing centrifugal pumping set / Monoblock pumping set 40 HP.

All as per item No. 82 here in above, but for the single stage split casing centrifugal pumping set / Monoblock pumping set 10 to 15 HP.

All as per item No. 92 here in above, but for the single stage split casing centrifugal pumping set / Monoblock pumping set 3 to 7.5 HP. Note for item No 92 to 95 : Cost of new spare parts shall be measured and paid separately under relevant items of BOQ under.

Supply only new Cast Iron impeller for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Key of impeller for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new pump shaft made of EN9 steel for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new gun metal bush for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron gland flange for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for pump of 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new love joy coupling for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for motor of 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Sleeves Cover for motor of 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Motor shaft for 60 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron impeller for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Key of impeller for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new pump shaft made of EN9 steel for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new gun metal bush for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron gland flange for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for pump of 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new love joy coupling for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for motor of 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Sleeves Cover for motor of 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Motor shaft for 40 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron impeller for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Key of impeller for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new pump shaft made of EN9 steel for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new gun metal bush for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron gland flange for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for pump of 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new love joy coupling for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for motor of 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Sleeves Cover for motor of 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Motor shaft for 10 to 15 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron impeller for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Key of impeller for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new pump shaft made of EN9 steel for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new gun metal bush for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Cast Iron gland flange for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for pump of 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new love joy coupling for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new ball bearing for motor of 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Sleeves Cover for motor of 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

Supply only new Motor shaft for 3 to 7.5 HP single stage split casing cenrifugal pumping set / monoblock pumping set as per existing type.

M&L cutting out the burnt winding for 40-60 HP electric induction motor three phase stator, taking out burn out copper wire by cleaning the slots properly, re-winding the same as per original gauge, super enamelled the copper winding wire including insulating material i.e. varnishing, cotton tape, insulating paper, sleeves drying the winding with required temperature re-assembling the rotor and stator after cleaning complete all as specified and as directed.

All as per item No. 136 here in above, but for 10 to 15 HP electric induction motor three phase stator.

All as per item No. 136 here in above, but for 3 to 7.5 HP electric induction motor three phase stator.

M&L painting to motors, pump sets, MS channels, foundations, suction and delivery pipes of 30 to 60 HP pump sets up to 5m length from pump sets including cleaning the outer surfaces of any description, in any position, applying one coat of synthetic enamel paint with proper colour codes and writing letters of SM No. and MES No. etc., complete all as specified and as directed.

All as per item No. 139 here in above, but for 10 to 25 HP pump sets.

S&F in repair MCCB, 4 pole, 250 Amps, 36 kA, 415 Volts, 50 Hz, AC including electric connection & testing complete all as specified and as directed. Make: Legrand/ Schneider/ L&T/ ABB/ Siemens

S&F in repair MCCB 4 pole, 200 Amps, 36 kA, 415 Volts, 50 Hz, AC including electric connection & testing complete all as specified and as directed. Make: Legrand/ Schneider/ L&T/ ABB/ Siemens

S&F in repair MCCB 4 pole, 160 Amps, 25 kA, 415 Volts, 50 Hz, AC supply including electric connection & testing complete all as specified and as directed. Make: Legrand/ Schneider/ L&T/ ABB/ Siemens

S&F in repair MCCB 4 pole, 100 Amps, 25 kA, 415 Volts, 50 Hz, AC supply including electric connection & testing complete all as specified and as directed. Make: Legrand/ Schneider/ L&T/ ABB/ Siemens

S&F single phase preventer & dry run protection relay (current based), AC, 415 V including commissioning & testing including taking down existing unservicable single phase preventer complete all as specified. Make: Minilec / L&T / C&S

S&F contactors ML-3 including taking out existing unseviceable contractor including electrical connection complete all as specified and as directed. Make: Legrand / Schneider / L&T / ABB / Siemens

M&L submersible cable copper conductor size of 3 core, 16 sqmm, flat, multistranded and waterproof including taking down unservicable cable complete all as specified and as directed.

All as per Item No. 147 here in above, but of size 3 Core, 10 Sqmm

All as per Item No.147 here in above, but of size 3 Core, 6 Sqmm

All as per Item No. 147 here in above, but of size 3 Core, 4 Sqmm

Supply and lay in repairs High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches 50 mm bore for protection of submersible cable in trenches including all necessary fittings complete all as specified and as directed. Note: Earth work and excavation shall measured and paid separately.

S&F motor backlite terminal plate having six terminal as per existing size / shape with copper alloy nuts, bolts and washers for 40/ 60 HP motor including taking down unservicable terminal plate complete all as specified.

M&L for repairing cast iron sluice valve 80 mm bore flanged type of any make by dismantling the valve, replacing SS spindle, bolts, nuts, washers, gaskets, wedgenut etc, re-assembling and refixing the same in position including replacing the worn out gland packing & testing and make good complete all as specified and as directed.

All as per Item No. 153 above here in, but sluice valve 100 mm bore.

All as per Item No. 153 above here in, but sluice valve 150 mm bore.

All as per Item No. 153 above here in, but sluice valve 200 mm bore.

All as per Item No. 153 above here in, but sluice valve 250 mm bore.

All as per Item No. 153 above here in, but sluice valve 300 mm bore.

Taking down existing sluice valve and S&F sluice valve cast iron body, double flanged and drilled, 80 mm bore as per IS-14846, class PN-1.6, long body type with SS spindle etc with all fittings, jointing materials etc. complete all as specified and as directed.

All as per Item No. 159 here in above, but 100 mm bore.

All as per Item No. 159 here in above, but 150 mm bore.

S&F in repairs Non return valve cast iron body with nitrile rubber ball as per IS-5312, class PN-1.6, double flange with reinforced ball suitable for 80 mm bore complete.

S&F in repairs Non return valve cast iron body with nitrile rubber ball as per IS-5312, class PN-1.6, double flange with reinforced ball suitable for 100 mm bore complete.

S&F in repairs Non return valve cast iron body with nitrile rubber ball as per IS-5312, class PN-1.6, double flange with reinforced ball suitable for 150 mm bore complete.

S&F in repairs CI foot valve flanged and drilled type with ISI marked conforming to IS:1538 of 80 mm bore complete all as directed.

S&F in repairs CI foot valve flanged and drilled type with ISI marked conforming to IS:1538 of 100 mm bore complete all as directed.

S&F in repairs CI foot valve flanged and drilled type with ISI marked conforming to IS:1538 of 150 mm bore complete all as directed.

S&F in repair fully automatic DOL motor starter in sheet steel enclosure for 3 to 5 HP with SPP feature complete including disconnecting and reconnecting by using proper lugs complete. Make: L&T Model No. MK1 DOL or equivalent in Siemens / Schneider / C&S.

S&F in repair fully automatic DOL motor starter in sheet steel enclosure for 7.5 to 15 HP with SPP feature complete including disconnecting and reconnecting by using proper lugs complete. Make: L&T Model No. MK1 SASD or equivalent in Siemens / Schneider / C&S.

S&F in repair fully automatic star Delta motor starter in sheet steel enclosure for 25 to 30 HP with SPP feature complete including disconnecting and reconnecting by using proper lugs complete. Make: L&T Model No. MUG-30 FASD or equivalent in Siemens / Schneider / C&S.

S&F in repair fully automatic star Delta motor starter in sheet steel enclosure for 40 to 60 HP with SPP feature complete including disconnecting and reconnecting by using proper lugs complete. Make: L&T Model No. MUG-50 FASD or equivalent in Siemens / Schneider / C&S.

Pumping out the water from under ground sump of size 24.80x16.45x5.30 m and capacity 2,00,000 Gallons and remove sludge / mud thoroughly, clean entire portion of sump by scrapping with wire brushes, broom and wash out by flushing clean water and drain out, clean entire inner portion of sump by bleaching powder, and apply one coat of white wash on inner surfaces of sump, at Pump House No.1 including marking the Date of cleaning, due date for next cleaning and capacity of sump etc with painting complete all as specified. Note for Sl item No. 172 to 177: i) Contractor has to make his own arrangements for Pumping out the water from Sump including T&P and necessary safety measures for cleaning of sump. ii) Job is to be carried out in one day.

All as per Item No. 172 here in above, but size of sump 24.40x15.25x4.30 m, and of capacity 1,50,000 Gallons at Pump House No. 1.

All as per Item No. 172 here in above, but size of sump 17.50x15.50x5.50 m, and of capacity 1,25,000 Gallons at Pump House No. 1.

All as per Item No. 172 here in above, but size of sump 16.50x15.50x5.30 m, and of capacity 1,00,000 Gallons at Pump House No. 2.

All as per Item No. 172 here in above, but size of sump 5.90x5.90x2.20 m, and of capacity 10,000 Gallons at NEMCC

All as per Item No. 172 here in above, but size of sump 6.50x6.50x2.20 m, and of capacity 15,000 Gallons at Pump House No. 1 (For RO Plant)

Drain out water from Over Head Tank (OHT) capacity 1,00,000 gallons at 18.3 m height from ground and remove the sludge / mud thoroughly, clean inner surface of the tank by scrapping with wire brush, broom and wash out by flushing with clean water and drain out for OHT No. 6 & OHT No. 3. Note for Sl item No. 178 to 181: i) Contractor has to make his own arrangements for Pumping out the water from OHT including T&P and necessary safety measures for cleaning of OHT.

All as per Item No. 178 here in above, but tank capacity 50,000 gallons at 18.30 m height from ground (OHT No. 1, 2, 5, 7, 9 & 10).

All as per Item No. 178 here in above, but tank capacity 25,000 gallons at 18.30 m height from ground (OHT No. 4).

All as per Item No. 178 here in above, but tank capacity 10,000 gallons at 18.50 m height from ground (OHT No. 8)

Pumping out the water from static water under ground sump capacity 25,000 gallons and remove sludge/ mud thoroughly, clean entire portion of sump by scrapping with wire brushes, brooming and wash out by flushing clean water and drain out, clean entire inner portion of sump by bleaching powder, apply one coat of cement slurry wash to inner surface of sumps, at various location including marking the Date of cleaning and due date for next cleaning and capacity of sump etc by painting complete all as specified. Note for Sl item No. 182 to 185: i) Contractor has to make his own arrangements for Pumping out the water from static water under ground sump including T&P and necessary safety measures for cleaning of static water under ground sump. Location: Valsura area.

All as per Item No. 182 here in above, but for 20,000 gallons.

All as per Item No. 182 here in above, but for 15,000 gallons.

All as per Item No. 182 here in above, but for 10,000 gallons.

M&L for valve chamber structure/ supports, base frames, MS sheet, structural steel including hinges duly fabricted and painting with two coats of first quality synthetic enamel paint over a coat of zinc chromate primer including taking down existing itmes etc complete all as specified. Note: Quoted rate shall deemed to be inclusive of painting.

M&L for earthing complete with galvanized steel earth plate as electrode 600x600x6 mm buried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth not less than 1.5 m below ground level connected using galvanized iron earth lead strip 25x4 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI earth lead strip protected by Gl light grade pipe 40 mm bore, including provision of concrete pit of PCC 1:2:4, type B1 (using 20 mm graded stone aggregate) with 40 mm thick cover of RCC 1:2:4 reinforced with 8 mm dia TMT bars reinforced at 100 mm C/C both ways and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 2 m long placed on top edge of earth plate, char coal and common salt filling test point made out of 40x8 mm flange with fixing arrangement, funnel, wire mesh and earth work in any type of soil, returning, filling in and removal of surplus soil to a distance not exceeding 50 m all as per electrical Plate No. 3 of SSR Part I and connected to earth test point complete all as specified including testing on completion and including taking down existing earthing complete.

S&F CI/ DI pipe fittings bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. "Y" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc. for 80 mm to 300 mm pipe line including taking down existing old CI/ DI pipe fittings complete.

S&F in repair ammeter digital, panel board mounting square type range 0 to 150 and 200 Amps, CT ratio 200/5 complete.

S&F in repair LED indicator lamp.

S&F in repair gland packing rope with lead graphite type of size 6 mm to 40 mm.

Taking down old rusted/ worn out GI tubing & connections fixed in any despriction and S&F new 80 mm bore GI tubing medium grade (ISI Marked) including necessary fittings (ISI Marked) such as bend, tee, elbow etc laid in trenches/ floors or fixed on wall complete all as directed.

All as per item No. 192 here in above but for 100 mm bore

All as per item No. 192 here in above but for 150 mm bore

M&L to attend 'B' check for DG set of capacity 63 kVA (Make:Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as ordered including testing on completion of the following all as directed:- (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer,Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning. (xii) Change of Air filter element with O ring. (xiii) Change of filter insert with O ring (xiv) Change of Lub oil filter. (xv) Change of Primary filter element. (xvi) Change of secondary filter element. (xvii) Change of greaves lub oil CI4- 10ltrs pack (xviii) Change of Radiator pre-mix greaves kOOL 10 ltrs, complete to the satisfaction of Engr -in-charge. (Note: Cost of New minor spares required for replacement to make the DG set fully functional is included in quoted rate.)

All same as per item No. 195 here-in-above, but DG set of capacity 100 kVA Make: Greaves

All same as per item No. 195 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20Ltrs pack complete for DG set of capacity 160 kVA Make: Greaves

All same as per item No. 195 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20Ltrs pack complete for DG set of capacity 250 kVA Make: Greaves

M&L and attend 'B' check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc.(ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging, Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Spinon Lub oil filter (xiii) Change of air cleaner element (xiv) change of Belt- AVX 10 1500 (xv) Change of fuel filter element (xvi) Change of KOEL care premium genuine oil 7.5Ltrs Can, complete all as specified and directed by Engr-in-charge. (Note: Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd, will be made on this account to contractor.)

All same as per item No. 199 here-in-above, but change of V Belt cogged- AVX10 1265L blower pulley, Change of V Belt cogged-AVX10 1136 for alternator pulley and Change of KOEL care premium genuine oil 13Ltrs Can, complete for DG set of capacity 40 kVA Make: Kirloskar

M&L and attend 'C' check for DG set of capacity 63 kVA (Make: Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed: (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Gskt set 4G11TA (w/o Hd gskt) (xiii) Change of cogged belt AX43-1143L (xiv) change of pipe turbo oil supply (xv) Change of pipe turbo drain (xvi) Change of set of hoses for 4G valve (xvii) Change of setting screw (xviii) Change of hex nut M8x1 DIN934 (xix) Change of gasket for PDC rocker cover (xx) Change of set of flex F/P (xxi) Change of push rod. (Note: Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd will be made on this account to contractor.)

All same as per item No. 201 here-in-above, but DG set of capacity 100 kVA Make: Greaves

M&L and attend 'C' check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following all as directed: (i) Check and clean engine,alternator battery,instrument panel,AMF panel,Timer,Contactors,Meters and others etc. (ii) Tightening of all nuts& bolts of DG set and its accessories. (iii) Check for any diesel lekage from any point and rectify if observed. (iv) Check and adjust fan belt tension ,replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer,Repair if required. (vi) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order. (vii) Check and tighten the AVM pads nuts and bolts,change AVM pads if found damaged. (viii) Check exhaust pipe,flange and lagging Repair if found damaged. (ix) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling,Greasing and checking for proper & smooth functioning(xii) Change of rocker cover gasket (xiii) Change of valve seat insert inlet & exhaust (xiv) change of valve pair inlet & exhaust (xv) Change of set of joints (xvi) Change of set of O rings HA294 (xvii) Change of intermediate ring 1.1mm (xviii) Change of valve guide (xix) Change of valve stem seal , complete all as specified and directed by Engr -in-charge. (note :- Cost of New spares required for replacement is included and no seperate payment for minor spares if any reqd, will be made on this account to contractor. )

All same as per item No. 203 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar

Supply only set of hoses with clipsfor DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of fuel pipes for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only set of injector pipes for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Exhaust silencer for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only injector with nozzle for DG set of capacity 63/ 100 kVA Make: Greaves

M&L for greaves lubricating oil SAE 15W40 suitable for DG Set.

M&L for Coolant suitable for DG sets make Fleetguard, Valvoline, Premium

Supply only Air filter outer for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only Air filter inner for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only 12V temp guage (40-120 deg cel) for DG set of capacity 63/ 100 kVA Make: Greaves

Supply only 12V press guage, 0-10 bar for DG set of capacity 63/ 100 kVA Make: Greaves

Servicing and caliberation of FIP (Fuel injection pump) & nozzles including replacement of minor parts like nuts,bolts,washers etc of following :-DG Set 63/100 KVA capacity

M&L for taking out Radiator of DG set 63 kVA/100 kVA Make: Greaves for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed.

M&L for taking out Radiator of DG set 160 kVA/250 kVA Make: Greaves for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed.

Servicing & repair to self starter of DG set of capacity 15/40 kVA (Make: Kirloskar) including replacement of parts such as washer, nut, bolts, bush, solenoid, rotor etc. assembling and testing complete.

All same as per item No 219 here-in-above, but for DG set of capacity 63/100 kVA Make: Greaves

All same as per item No 219 here-in-above, but for DG set of capacity 160/250 kVA Make: Greaves

S&F in repair Solonid Switch for 15/ 40 kVA DG set Make: Kirlosakar and testing complete for proper functioning.

S&F in repair Solonid Switch for 63/ 100 kVA DG set Make: Greaves and testing complete for proper functioning.

S&F in repair Relay card for 15/ 40 kVA DG set Make: Kirlosakar and testing complete for proper functioning.

S&F in repair Relay card for 63/ 100 kVA DG set Make: Greaves and testing complete for proper functioning.

S&F in repair Solonid Switch for 160/250 kVA DG set Make: Greaves and testing complete for proper functioning.

S&F in repair AVR suitable for 15 kVA DG Set complete all as directed.

S&F in repair AVR suitable for 40 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 63 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 100 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 160 KVA DG Set complete all as directed.

S&F in repair AVR suitable for 250 KVA DG Set complete all as directed.

S&F in repair battery auto cable copper PVC insulated unsheathed 35 Sqmm single core copper cable complete.

S&F in repair battery auto cable copper PVC insulated unsheathed 95 sqmm single core copper cable complete.

S&F 90AH 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for DG set. Make: Exide Xpress

S&F 150AH 12Volt 12Volt Lead acid battery (Maintenance free battery with min 2 years warranty) for DG set. Make: Exide Gold

S&F battery lugs for DG set battery complete all as directed by Engr in charge.

S&F in repair Ignition Switch of DG Sets & complete all as directed.

S&F in repair No volt coil for contactor of capacity up to 200 Amp Capacity all as specified and as directed by EIC. Make : L&T /C&S/Schneider

S&F in repair LED type pilot lamp. Make: C&S / L&T

S&F in repair Volt meter 0-500 Volt in existing panel including wiring from bus bar to volt meter terminals iand fix the wiring wit existing control wiring all as directed. Make: L&T/ Meco/ HPL

S&F in repair Ammeter 0-100 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring all as directed. Make: L&T/ Meco/ HPL

S&F in repair Ammeter 0-200 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring all as directed. Make: L&T/ Meco/ HPL

S&F in repair electronic timer of 215/240/360/415 Volt 3 to 120 Sec all as directed. Make: L&T/C&S/Schneider

M&L for wiring loom of control panel of DG Set AMF panel from Relay and auxilliary contacts complete by using 2.5 sq.mm copper cable of colour code from auxilliary contacts to Realy including fault finding etc all as specified and as directed.

M&L for Overhauling of water pump with repairing kit for 63/100 kVA DG set complete all as directed.

M&L for Overhauling of water pump with repairing kit for 160/250 kVA DG set complete all as directed.

M&L for complete checking of AMF panel,finding the fault, servicing complete including replacement of unserviceable spares and testing complete for manual & Auto operations all as directed. Note: Supply only of new items required for replacement will be measured & paid seperately under respective item of schedule.

Supply only AMF Relay.

Supply only single phase preventor.

Supply only PLA relay.

Supply only 3 pole power Contractor ML-4, 70 A, 415 V. Make: L&T/Legrand

S&F in repair HRC Fuse base of capacity 200 Amps.

Supply only 3 pole power Contractor ML-4, 163 A, 415 V. Make: L&T/Legrand

S & F Anti vibration pad set suitable for 63/ 100kVA DG set all as directed.

M&L for taking out alternator of DG set of capacity 15 kVA (Make: Kirloskar) by dismantling from engine pulley including disconnecting electrical connection complete & transporting to workshop. Opening the rotor and stator for rewinding with copper wire of existing guage and then revarnishing the stator & rotor with good quality varnish, Heating and baking complete upto requisite duration. Check bearing & shaft for machining if reqd. Re-assemble stator & rotor by replacing existing bearings with new bearings complete. Retransportation alternator to base and coupled with engine by using new rubber bushing spider, nutbolts complete. Testing the system for smooth functioning & checking current and load output by giving existing electrical load and to the entire satisfaction of engr in charge.

All same as per item No. 257 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar

All same as per item No. 257 here-in-above, but for DG set of capacity 63 kVA Make: Greaves

All same as per item No. 257 here-in-above, but for DG set of capacity 100 kVA Make: Greaves

M&L for Readymade electrolyte having specific gravity 1.4 for DG set of any capacity all as directed.

M&L for Distilled water having specific gravity 1.0 for DG set of any capacity all as directed.

S&F in repair MCCB thermal magnetic protection unit rating 160 Amp, 4 pole, 25 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items complete all as specified.Make:Legrand Cat No. 4200 57 or equivalent in ABB / Siemens/ L&T

S&F in repair MCCB thermal magnetic protection unit rating 100 Amp, 4 pole, 25 kA type DPX3 in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and ncluding necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items complete all as specified. Make:Legrand Cat No. 4200 55 or equivalent in ABB / Siemens/L&T

Supply, installation, commissioning and testing of Analogue Addressable Fire Alarm Control Panel including detector wise configuration facility 2000 Event Storage with Real Time Clock, Upto 192 grouping facility, Pre Alarm Action, Programmable detector sensitivity. Device type verification, Earth fault annunciation facility at 0 ohms, Double Address Sensing, Loop wise device test. 40 X 4 Characters LCD display 2 numbers of loop card and 200 devices in any combination per loop. Day / Night Mode facility. USB 2.0 Interface for PC connectivity. Rs. 485.00 Communication facility for Network / Repeater / MODBUS / BACnet. Programmable Auto Silence Facility. Programmable AC Loos Delay. Programmable Silence Inhibit. Two No’s of programmable inputs. Battery low audio, visual warning. Three programmable Form C relay for Fire, Fault and Supervisory. Primary Power 120 / 220VAC + 10% -15%, 60 / 50 Hz. Standby Power 24V D.C (2 No’s of 12V, 40 Ah (Max), Built in for 12Ah) Sealed Lead acid battery Operating Condition Operating Temperature 0 - 49° C / 32-120° F. Relative Humidity 93 ± 2% RH (non-condensing) at 32 ±2° C / 90 ±3° F including taking down old unserviceable Panel complete all as specified and as directed.

Supply commissioning and testing of Smoke detector Operating Voltage Range: 9 to 32 VDC Volts Non-polarized Standby Current: ≤100µA @ 24 VDC, Maximum Alarm Current (LED on ): ≤55mA @ 24 VDC, Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing, Operating Temperature Range: 14°F to 120°F (-10°C to 49°C), Adjustable Sensitivity: 1-2.5%/FT, Height: 2.2 (55 mm) installed in Base including taking down old unserviceable smoke detector complete all as specified and as directed.

S&F in repair of Batteries DC, 12V, 7 AH, lead acid duly initial charged complete all as specified and as directed. Make: Exide / Star Gold

Supply, commissioning and testing of Fire Alarm Hooter made out of iron, red colour operating voltage 24 DC supply Dimensions (L x B x H): 18.5cm x 13 cm x 7.5 cm including taking down existing fire alarm hooter complete all as specified and directed.

Supply, commissioning and testing of Addressable manual call point resettable type including taking down existing addressable maual call point complete all as specified and as directed.

S&F in repair of Hydrant valve single headed Gun metal landing valve (internal/external Fire-Hydrants) with oblique type single outlet complete with hose coupling adaptor of 63 mm size, instantaneous spring lock arrangement and blank cap with chain conforming to IS 5290 complete all as directed

S&F in repair of Flanged stand post CI of 80 mm dia 1.5 m height complete all as directed

suvidhiconstruction

J J ENTERPRISE

M/s Jagdish Machinery Stores

Jyoti Refrigeration

JAYESH TRADING CORPORATION

ambika electric co

JAMNAGAR ELECTRIC AND MACHINERY CO