Special repairs to building No P-99 to P-102 at D Sector Dolphin Hill under GE NB, Visakhapatnam

Amount

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for 25 mm average thick PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in levelling course over sub base, surface finished even and fair to receive topping layer complete all as specified and as directed.

M&L for 10mm thick (roof treatment plaster) rendering in CM (1:3) on concrete surfaces using water proofing compound and finishing the surface even and fair without using extra cement complete all as specified and as directed. Note: WPC shall be measured and paid seperately.

Supply only Integral water proofing compound.

M & L Priming the surface with oil based bituminous primer @ 0.50 KG per Sq.m and laying of 3mm thick Attatic Poly Proplene Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion all as specified and as directed.

M & L for Chequered Cement Concrete Tiles of size 300 X 300 mm, 20 to 25mm thick, Hydraulically pressed as in Floors, set jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 of cement complete all as specified and as directed.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance not exceeding 5.0 KM complete all as specified and as directed.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 8 to 10 mm thick as in Floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size not exceeding 0.36 Sq.m, 8 to 10 mm thick as in Skirting and Dado, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm or 350 mm x 250 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

Dismantling of mangalore tiles in flooring, apron etc of any description or thickness laid dry and pointed in any mortar complete all as specified and directed.

M&L for providing roof cooling ceramic tiles of size 300 x 300 mm, 7 to 8 mm thick, conforming to IS 15622, set and jointed in cement slurry and pointed flush with high performance polymer modified cementitious non slip tile adhesive to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: [a] The colour/ shade/ design of tiles shall be as approved by GE.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance not exceeding 5.0 KM complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

Taking down Chowkats or frame with shutters exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

S & F factory made single rebated Wood Polymer Composite [WPC] solid door/ window/Ceosetory windows Frames/ Chowkhats of size 65mm x 125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms), fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properties of termite / borer proof, water/ moisture proof and fire retardant, fixed in position complete all as specied and as directed. Note: The hold fasts/ lugs/ fasteners shall be measured and paid separately under relevant items of this Schedule/ BoQ.

S & F factory made single rebated Wood Polymer Composite [WPC] solid door/ window/Ceosetory windows Frames/ Chowkhats of size 65mm x 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms), fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properties of termite / borer proof, water/ moisture proof and fire retardant, fixed in position complete all as specied and as directed. Note: The hold fasts/ lugs/ fasteners shall be measured and paid separately under relevant items of this Schedule/ BoQ.

S & F factory made single rebated Wood Polymer Composite [WPC] solid door/ window/Ceosetory windows Frames/ Chowkhats of size 50mm x 75mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms), fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properties of termite / borer proof, water/ moisture proof and fire retardant, fixed in position complete all as specied and as directed. Note: The hold fasts/ lugs/ fasteners shall be measured and paid separately under relevant items of this Schedule/ BoQ.

S & F Factory made 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 0.9 mm thick Decorative Laminate, Type - 1 of Surface Finish, Colour and Pattern as approved, fixed with approved adhesive as per manufacturer's instructions, including necessary preparation of surfaces complete all as specified and directed.

S & F 35mm thick Factory made, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed.

S & F Stainless steel wire cloth / mesh with average aperture not exceeding 1.18 mm and dia of wire 0.28 mm and fixed with tinned tacks or Aluminium wire staples with new wooden beading including necessary painting to beading to match with existing surfaces complete all as specified and as directed.

S&F wood plastic composite (wpc) factory made door shutter of 30 mm thickness made out of single pieces extruded wpc (wood plastic composite) profile with homogenous fine cellular structure made with plastic and wood powder having solid structure which is eco friedndly with density not less than 650 kg/cum,anduv digitally printed to the desired design with uvlacquar coated to give surface added strength and protectionand high grade uv resistance and with heat, fire retardant will be hung and screws withdrawl strength 1800 n(face) & 900 n (edge), minium compressive strength of 50n/mm2 , E=900 n/mm2 and resistance to spread of flame of class a category with property of being termite / borer proof water/ moisture proof and fire retardant and fixing with stainless stel butt hinges of required size with necessasry full body threaded star headed counter sunk s.s screw of size 10mm dia and 100 mm long , complete all as specified and as directed.

S & F Stainless steel Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F 100 mm size, Butt hinges, Stainless Steel, with SS hinge pin including fixtures complete all as specified and as directed.

S&F 200mm long stainless steel, barrel tower bolts of extruded section complete all as specified and as directed.

S&F floor door stopper of Stainless steel, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm.complete all as specified and as directed.

S&F 300 mm long Stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.complete all as specified and as directed.

S&F 200mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed.

S&F 100mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished , typeB-11 complete all as specified and directed.

S&F 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts complete all as specified and directed.

S&F 150mm Extruded brass handles, fabricated type polished complete all as specified and directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-1, using 20 mm graded stone aggregate as in Bed blocks and Bed plates including weathering, slightly rounded or chamfered angles and throating, necessary form work etc complete all as specified and directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S&F 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F in repairs 110 mm Anti-Cockroach Stainless steel grating fixed with white cement complete all as specified and as directed.

S&F in repairs 75 mm Anti-Cockroach Stainless steel grating fixed with white cement complete all as specified and as directed.

Dismantling of cast iron drain pipes, jointed in cement mortar of 100mm internal dia of pipe.complete all as specified and as directed.

Dismantling of cast iron drain pipes, jointed in cement mortar of 75mm internal dia of pipe.complete all as specified and as directed.

S&F PVC (SWR) pipes 110 mm single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm single socketed in any length with rubber ring joints fixed to wallscomplete all as specified and as directed.

S&F PVC (SWR) bends 110 mm any radius complete all as specified and as directed.

S&F PVC (SWR) 110 mm branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F PVC (SWR) bends 75 mm any radius complete all as specified and as directed.

S&F PVC (SWR) 75 mm branch piece, single (single Y) equal or unequal complete all as specified and as directed.

M&L 75 mm dia PVC floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

M&L 75 mm dia PVC Nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4) complete all as specified and as directed.

S&F in repairs for 15mm bore, 60 cm long PTMT PVC connecting pipe fitted with brass unions to connect iron pipe to PVC pipe on both ends complete all as specified and as directed.

S&F 10 litres capacity PVC valveless,syphonic action type, flushing cistern low level white with inlet ball valve float and handle including brackets complete all as specified and directed.

S&F in repairs 15mm dia long body fancy type bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F 15mm dia long body swan neck pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs 15mm dia stop valves/ angle cocks, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs 15mm dia cast copper alloy, chromium plated two way angle cocks screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs Health Faucet, ABS body, including 1.25 m long flexible tube, ABS wall hook, non return valve complete all as specified and directed.

S&F in repairs 15mm dia bore Brass CP mixer for mixing hot & cold water screwed down for iron pipecomplete all as specified and directed.

S&F in repairs 32mm dia PVC waste pipes 900mm long.complete all as specified and directed.

S&F in repairs Fancy type brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repairs towel rack 600mm long with lower hangers complete all as specified and as directed.

S&F in repairs Under counter vitreous China wash basin oval shape of size minimum 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and 32mm brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed.

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces, ceiling surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 5.0 KM complete all as specified and as directed.

M & L for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacturers instructions over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on Ceiling surfaces by using vaccume based sanding machine, removal of nails and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one coat of alkali resistant primer on wall surfaces over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on wall surfaces by using vaccume based sanding machine, removal of nails and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one coat of alkali resistant primer on wall surfaces over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over two or more coats of Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty on newly plastered walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering through their authorised applicators before commencement of the work to GE for approval.

M & L for Complete removal of existing treatment of any description on walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections by using vaccume based sanding machine, removal of nails including rubbing with sand paper to obtain a smooth surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over two or more coats of Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty complete all as specified and as directed. Note:- The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for preparing newly plastered wall surfaces by using vaccume based sanding machine and applying two coats of Acrylic washable Distemper by using auto roller/airless sprayer, over a coat of alkali resistant primer on ceiling over two or more coats of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for two coats of white wash on old decorated surfaces of walls etc including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for two coats of white wash on old decorated surfaces of ceiling etc including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Triple Layered, ISI Marked, Cylindrical & Vertical Type 500 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes including dismantling and taking out existing unserviceable PVC tanks of any description and capacity complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Triple Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes including dismantling and taking out existing unserviceable PVC tanks of any description and capacity complete all as specified and as directed.

S & F in repairs Ball Valves, 25 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe etc complete all as specified and as directed.

S & F in repairs Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe etc complete all as specified and as directed.

M & L for providing two components acrylic polymer modified cementitious elastomeric water proof coating, minimum 1.5 mm thickness [DFT], with nominal coverage of 2.2 Kg/Sqm including thorough preparation of surfaces by mechanical means to obtain a plain and level surface including sprinkling of clean and washed sand on final coat when wet all as per manufacturuer's instructions, as specified and as directed. Notes: [a] The coating shall have minimum 1 N/mm2 tensile strength, elongation of a min 80% when tested as per ASTM D 412, resisting 5 bar hydrostatic pressure as per DIN 1048 and having crack bridging ability of upto 2 mm. [b] The coating shall cover all the wet areas of floor and the vertical walls for a height of minimum 4 feet above the floor. [b] The rate quoted shall be deemed to include for the following: [i] Filling of all cracks and crevices with approved epoxy based mortar and making good to receive waterproofing coating treatment. [ii] Providing additional coat reinforced with a fibre band sandwiched between 1st and 2nd coat along the periphery of the toilet floors, around protrusions and around pipes.

M & L for filling polymer modified non shrinking slurry with CEBEX 100 (Fosroc) chemical for sunken floors for toilets by drilling holes to a depth of 60mm by 20mm dia at 1 mtr interval and applying 2mm thick brush bond over the concrete syrfaces by mixing acrylic emulsion NITO BOND BB with brush bond powder and water and testing the same for 48 hours with complete filling with in the sunken floor as per the manufacturer's instruction and technical specification complete all as specified and as directed (Make: M/S Fosroc or M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd.) work up to G+4th storey complete all as specified and as directed.

Providing and filling light weight AAC bats (of size 40-60 mm) with cement mortar mixed in the ratio 1:3:6 (1 cement : 3 coarse sand : 6 block bats) including mixing of approved water proofing compound in recommended proportion. The laid brick bat mix shall be well rammed and compacted as required. Care shall be taken prior to filling all pipes passing through sunk portion such that the pipes are pressure tested by maintaining pressure for 24 hours and junctions of pipes passing through walls, slabs are well grouted and sealed. This shall be tested by ponding water for required depth and maintaining for 72 hours. (Rate includes cost of AAC bats, cement mortar, top screed, labour charges for working at all levels, leads and heights). For payment the area of sunken slab and the depth of filling shall be measured complete all as specified and as directed.

S&F Fancy type wall mounted bevelled edged looking mirror of size (900mm X 600 mm), 5mm thick complete all as specified and as directed.

S & F in repairs Stainless steel kitchen sink with draining board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S & F in repairs Stainless steel kitchen sink, made of stainless steel 1 mm thick, with plugs, washers and Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long including bedding in cement mortar on to dwarf wall or including fixing cantilever CI Brackets and connecting union to pipe, overall size 495mm X 420mm, bowl size 410mm X 330mm X 160mm complete all as specified and as directed.

M & L for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing necessary joints 12mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

M&L for 18mm thick, factory made ready to install, Non-toxic, Lead & Cadmium free, single extruded, water proof, termite proof, fire retardant, excellent screw holding capacity, solid WPC board, one side decorative choice lamination and lipping with other side balancing white as in cupboard shutter, fixed to door frame with and cold rolled nickel plated steel 'O' crank soft closing concealed hinge (15-22mm) 8 Nos for bottom portion 4 Nos for loft above including necessary fixing arrangement, bright finish or Electrogalvanized and width of flaps 40mm (when open) and stainless steel screw complete all as specified and directed.

S & F in repair Factory made ready to install Non-Toxis, Lead & Cadmium free, single extruded Water proof, termite proof, fire retardant, excellent screw holding capacey, Solid WPC Boards 18mm thick of White Colour as in Cupboard Shelves fixed to pvc guide Rails with stanless steel screws complete at as specified as directed

S&F 150 mm long designer SS pull handles with fixing accessories of standard Each grade for cup board shutter complete all as specified and as directed

S&F 100 mm long designer SS pull handles with foxing accessories of standard Each grade for cup board shutter complete all as specified and as directed

S&F hasp and staple, safety type, aluminium anodised 100 mm with mild steel hinge pin including bolt to hinge plate and fixed with screws.complete all as specified and as directed

S&F Corner Glass Self 30 cm radius , 5mm thick glass with SS Bracket complete all as specified and as directed.

S&F rectangular Glass Self (With SS Bracket) Glass Shelf 600 X 100mm Long complete all as specified and as directed.

S&F in repair 300 mm MS ordinary rat tail rod pattern springs and including roller and roller plate complete fixed in repairs complete all as specified and as directed.

S & F Magnetic Catches with Striking Plate, First quality suitable for Cupboard Each shutters complete all as specified and as directed.

S & F in repairs Stainless Steel Plate Rack of size 900 mm X 750 mm X 250 mm of approved pattern made out of stainless steel sheet 18 gauge with round 8mm dia rods complete all as specified and directed.

S&F Towel Ring of Stainless steel fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed

S & F in repairs Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre and Decorative type brass Globe type Brackets of size suitable to 25mm dia curtain rod complete all as specified and as directed.

S & F in repairs, Brass Chromium Plated Shower Rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed.

S & F 100 mm, Brass Mortice Lock with 4 Levers, vertical type with keys complete all as specified and as directed.

S & F Stainless Steel Toilet Paper Holder, Chromium plated, Fancy type complete all as per Jaquar Catalogue No. AHS-1553 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

Taking down and Refixing of wooden shutter in the same or other opening shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each after easing and adjusting complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep in Soft / Loose soil complete all as specified and as directed.

M & L for 150mm dia RCC Pipes, Class NP3, laid and jointed with collars laid in trenches and jointed with cement mortar including taking down of old pipe of any description complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed.

S&F of FRP manhole cover of length of 1.3 m X 0.85 m of thickness 100 mm complete all as specified and as directed.

S & F CPVC Pipes 20 mm outer diameter SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

S & F CPVC Pipes 25 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

S & F CPVC Pipes 32 mm outer diameter SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing including taking down of existing unserviceable GI pipes and connections of any description complete all as specified and as directed.

S&F 10mm thick powder coated anodised aluminium deco grill DG-102, including joining cleat for fixing and necessary fixing arrangements as required, complete all as specified and as directed.

S&F plain Sheet glass, 5.5 mm thick ordinary quality and glazing with beads, in square exc 0.5 sq. m in each pane all as specified and directed.

M & L for Powder coated aluminium sections of approved colour for doors, Windows, Ventilators, Partitions, with frames and shutters fully or partly glazed, sliding / openable, with extruded aluminium sections of thickness not less than 1.5mm thick and powder coating with not less than 60 micron thick including necessary jointing cleats, rubber beading, neoprene packing, aluminium snap beading, screws, powder coated aluminium fittings such as handles, aluminium butt hinges , aluminium tower bolts, stainless steel friction hinges,locking arrangements etc.complete all as specified and as directed. Note:- [a] The size of aluminium extruded sections shall conform to Designation 63400 all shall be as specified in relevant IS code and as specified in MES Schedule Part - I. [b] Panel inserts such as Glass / Particle board / Gauze shall be measured and paid separately at supply only rates. [c] Weight of aluminium sections shall only be accounted for payment purpose. Weight of aluminium Handles, Butt Hinges & Tower Bolts shall not be accounted for payment purpose. [d] The unit rate quoted shall be deemed to include for cost of jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges,Peg stays, locking arrangements etc., and fixing only of panel inserts of glass / particle board / gauge etc.

M&L for 18 mm thick factory made ready to install, non toxic , lead & cadmium free, single extruded, water proof, fire retardent and with excellent screw holding capacity , solid HDHMR board with 0.9mm thick , one side decorative acrylic choice lamination and other side balancing white as in cupboard shutter , fixed to door frame with bright finish or electrogalvanised and width of flasp 40 mm (when open) and stainless steel including liping the cut edges with same material finish complete all as specified and directed.

S & F in repairs stainlesss steel wire basket(cutlery basket)pull out type, of size 535 mm x 510 mm x100 mm Grade 304 with necessary fixing clips etc, fixed in repair complete all as specified and directed. (Note- Work shall be carried out as per manufacture's instructions)

S & F in repairs stainlesss steel wire basket(cup and saucer basket)pull out type, of size 535 mm x 510 mm x100 mm Grade 304 with necessary fixing clips etc, fixed in repair complete all as specified and directed. (Note- Work shall be carried out as per manufacture's instructions)

S & F in repairs stainlesss steel wire basket(thali basket)pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc, fixed in repair complete all as specified and directed. (Note- Work shall be carried out as per manufacture's instructions)

S & F in repairs stainlesss steel wire basket(plain basket)pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc, fixed in repair complete all as specified and directed. (Note- Work shall be carried out as per manufacture's instructions)

S & F in repairs stainlesss steel wire basket(plain basket) bottle pull out type, of size 535 mm x 510 mm x200 mm Grade 304 with necessary fixing clips etc, fixed in repair complete all as specified and directed. (Note- Work shall be carried out as per manufacture's instructions)

S & F in repair stainless steel sliding/telescopic channel of length 20 inch (500mm) with 3 Nos of holding ball of load carrying capacity 45-50 Kg of 202 grade steel, width 45mm including necessary fixing arrangement complete all as specified and directed.

S & F in repairs cold rolled nickel plated steel O crank soft closing concealed hinge (15-22mm) including necessary fixing arrangement to shutter complete all as specified and directed.

S & F in repairs stainless steel ventilator/ grill of size 100mmx100mm for cupboard shutter including necessary fixing arrangement to shutter complete all as specified and directed.

S & F in repairs stainless steel modular kitchen handle, 100mm long complete all as specified and directed.

M&L for followings :- (i) Removing plaster & finishes all around the coloumns, slabs & beams (on all four sidescription of column to full height , three sidescription of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. (The Engr-in-charge may order sand blasting if rust is approved) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 30 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 40 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed.(viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note : pressure shall be in the range of 1-2 kg/sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface of substrate off any dust /loose material after ageing of the grout as recommended by manufactuer.

M&L for Providing & Pouring Micro concreting M-40 grade :- (i) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed. Note : The cost of micro concrete M-40 grade & Epoxy bond coat is inclueded in this item.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar (Master flow 935 of BASF or equivalent FOSROC/SIKA) with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L complete removal of existing treatment on walls and applying dampproof treatment as follows 1. Apply a coat of damp proof advanced chemical on walls on removal of existing treatment. 2. Apply water proof putty (home shield) one or more coats on walls 3.Applying seal o prime over the putty surfaces complete all as specified and as directed.

Impregnating cream for injection into masonry or concrete wall 230 mm thick against capilary rising humidity. Rising bar super strong (Product no. 201) of chowgale building chemicals or equivalent pidlite/Drfixit/sika/phosrock complete all as specified and directed. Method of Applicaion Methodology (a) The surface must be sound, absorbent, clean, free of dust, oil, paint, curing agents, loose cement or lime plaster & concrete, debris, or any separation layers. (b) The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. (c) Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. All sharp edges/joints need to be levelled ; loose concrete to be removed. (d) Drill boreholes at ground level horizontally. The boreholes are drilled horizontal into the masonry. (e) The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. The boreholes hould have a diameter of 12mm upto a maximum of 15mm and should be spaced approx. 100 to 120mm apart and the vertical offset is 6 cm max. (f) Before inserting RisingBar Super Strong or equivalent the boreholes must be cleaned from boring dust by using air pressure. It is not necessary to pre-wet the borehole. (g) For applying of RisingBar Super Strong or equivalent the dosing system inserted as far as possible into the borehole. While dosing the product uniformly, the injection nozzle is pulled out leading to a completely filled borehole (h) Treatment of highly absorbent masonry might require repeated filling of the borehole. Depending upon extent of damage, RisingBar Super Strong or equivalent can be re-injected into the same hole after 24 hours. Depending on absorbency, application or masonry thickness 0.1 to 0.15 litre/m with 10 cm wall thickness.

Dismantling of stone slabs and tiles in flooring, apron etc of any description or thickness laid dry and pointed in any mortar complete all as specified and directed.

M & L for Kota Stone Slabs of 20 to 25 mm thick as in Floors, Gallery platforms,Steps, etc. with machine cut edges, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with Grey Cement [slurry] and jointed and pointed with grey cement slurry mixed with a admixture of pigment to match shade of Slabs, rubbing and grinding with mechanical equipment fitted with suitable grit size corborundum stones and polishing with Oxalic Acid to smooth, bright mirror finish over screed bed of 15mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire width of Platforms, Steps, etc.

M & L for Kota Stone Slabs of 20 to 25 mm thick in vertical surfaces of Gallery platforms, Skirting, Dado, Risers of Steps, Jambs, Pillars etc. with machine cut edges, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with Grey Cement [slurry] and jointed and pointed with grey cement slurry mixed with a admixture of pigment to match shade of Slabs, rubbing and grinding with mechanical equipment fitted with suitable grit size corborundum stones and polishing with Oxalic Acid to smooth, bright mirror finish over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of skirting / dado / risers and joints shall match with the flooring.

M&L for Granite (of any type) tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15 mm thick screed bed in cement mortor 1:6 as in flooring and steps set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Skirting, Dado, Risers of Steps, Jambs, Pillars, Wall Lining [Veneering to Wall] etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Skirting / Dado / Risers and joints shall match with the flooring.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed.

S & F in repairs Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [exclusive of steel sheeting or other covering, running rails and guides] and hanging, also fastening and fixing complete all as specified and as directed.

S & F Mild Steel, Plain, Black Sheet, 2mm thick as in hearths, covering to door shutters, covering to door Chowkats [frames], chullah hoods, water tanks, water troughs, ducts, urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched including round headed screws, clout nails or rivets and fixed to wood or steel members, etc. with plain 40 mm lap joints or welded / riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and as directed.

S & F in repairs Mild Steel work conforming to Fe - 290, Grade E-165 as in Hand Rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for Balusters Running Bars, for Doors, Balusters, Nosing to Steps including embedding in concrete and screwing etc., Wind Ties for roof including securing bolts, Posts and Struts in Fencing including cutting tops to shape as directed, bending to shape, notching for wire, drilling holes or as in flat iron fillets [for securing wire mesh and barbed wire etc.] including all necessary drilling, bolting or riveting, etc. and similar work complete all as specified and directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on old steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F Stainless Steel Railing made with Stainless Steel Pipes of wall thickness not less than 1.6mm, of Grade AISI 316L, standard quality, bright polish finish, using 50mm dia pipes for hand rail, 25mm dia pipes for vertical supports / balusters and 25mm dia pipes as in tie bars in three layers, SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed.

M & L for 10mm thick first class hard wood teak wood beading lipping around the flush doors shutters of area exceeding 3 sq cm and not exceeding 5 sq cm including polishing with French polish.

S&F wood plastic composite (wpc) factory made door shutter of 35 mm thickness made out of single pieces extruded wpc (wood plastic composite) profile with homogenous fine cellular structure made with plastic and wood powder having solid structure which is eco friedndly with density not less than 650 kg/cum,anduv digitally printed to the desired design with uvlacquar coated to give surface added strength and protectionand high grade uv resistance and with heat, fire retardant will be hung and screws withdrawl strength 1800 n(face) & 900 n (edge), minium compressive strength of 50n/mm2 , E=900 n/mm2 and resistance to spread of flame of class a category with property of being termite / borer proof water/ moisture proof and fire retardant and fixing with stainless stel butt hinges of required size with necessasry full body threaded star headed counter sunk s.s screw of size 10mm dia and 100 mm long , complete all as per direction of engg-in- charge.

Taking down carefully copper / aluminium point wiring [light, fan, socket or power] complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down MCCB DBs, MCB DBs, SPN / TPN Enclosures including MCCBs, MCBs etc of any description and any capacity and making good the disturbed surfaces all as per existing complete all as specified and as directed.

Taking down old / perished sub main wiring of any size aluminum condutor cable along with TW batten/ PVC conduit and making good the disturbed surface of wall complete all as specified and as directed.

M & L for Taking down Ceiling Fan of any description from its position and refixing the same after repairs to buildings, at same place or at new place including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm, replacement of Spares such as Capacitor 2.5 Mfd, Bearings, Shaft Bushes, Capacitor, Cotter Pin, Clamps, Rubber Bushes, Nuts & Bolts etc. as required and also including cleaning, greasing and spray painting with one coat of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and complete all as specified and directed.

M & L for Taking down Exhaust Fan of any description from its position and refixing the same after repairs to buildings, at same place or at new place including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm, cleaning, greasing etc and replacement of Spares such as Capacitor 4 Mfd, Nuts & Bolts, washers, etc. including cleaning, greasing and spray painting with one coat of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and complete all as specified and directed.

M & L for Overhauling of Geysers of 25 capacity of any make by dismantling the geyser by removing from its position by disconnecting electric connection, inlet & outlet water supply connections, detecting the leakage by removing the copper vessel and rectifying by soldering, testing, refixing in position including spray painting with two coats of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and replacement of Spares such as Heating Element, Thermostat, Plug Top, Indication Lamps, PVC Connection for Hot & Cold water and other minor components etc. complete all as specified and directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, Two runs, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Metal GI Flush Box of suitable size and thickness including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point complete all as specified and as directed. Note: The rate quoted shall be deemed to include cost of cutting chases not exceeding 10 cm girth, pinning in brick walls and making good in cement mortar as required.

All as per Serial Item No. 162 above but One 3 Pin Socket Outlet 5 Amps on same Board complete all as specified.

All as per Serial Item No. 162 above but One light point controlled by 2 Nos of Two way switches complete all as specified.

All as per Serial Item No. 162 above but one 3 Pin Socket Outlet 6 Amps on independent board, complete all as specified.

All as per Serial Item No. 162 above but one 3 Pin Socket Outlet 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

All as per Serial Item No. 162 above but one 3 Pin Socket Outlet 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F SRCD with one single pole MCB (C curve), 20 A, 240V AC modular type with 30mA earth leakage protection complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Socket Outlet, 3 pin, 16 Amps cum 3 pin 6 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Modular type, one module, Single pole, one way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Switch, Modular Type, One Module, Single Pole, Two Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Electronic Fan Regulator, Stepped Type, Modular Type, Two Module, 120 W, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Bell Push, Modular type, one module, Single Pole, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Ceiling Rose, PVC Body, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Bell, Ding Dong / Multi Music Type, AC, 230 Volts, Single Pole complete all as specified and as directed.

Taking down existing Light Fittings of any description and refixing the same after repairs to buildings, at same location or at new location including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including cleaning and carrying out minor repairs complete all as specified and as directed.

Supply and fixing Energy efficient LED tube light fitting with tube with minimum 5 watts or nearest available size ,240V, 50hz surface mounted, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate environmental friendly, energy efficient ready to use pack of complete with mounting bracket etc including connecting up with 1.5 sq mm 3 core flexible copper conductor cable including taking down existing unsweviceable light fittings complete all as specified and directed

Supply and fixing Energy efficient LED tube light fitting with tube 10 watts ,240V, 50hz surface mounted, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate environmental friendly, energy efficient ready to use pack of complete with mounting bracket etc including connecting up with 1.5 sq mm 3 core flexible copper conductor cable including taking down existing unsweviceable light fittings complete all as specified and directed

Supply and fixing Energy efficient LED tube light fitting with tube 20 watts or nearest size ,240V, 50hz surface mounted, decorative ultra slim round profile LED lighting fixture with extruded polycarbonate environmental friendly, energy efficient ready to use pack of complete with mounting bracket etc including connecting up with 1.5 sq mm 3 core flexible copper conductor cable including taking down existing unsweviceable light fittings complete all as specified and directed

S & F Energy efficient & Long life Security Light Luminaire, 35 Watt with Pressure die-cast Aluminium housing, IP 65 Protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 2.00 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing unserviceable security light complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Material and labour for submain wiring complete with earth wire of PVC insulated multistranded copper conductor FRLS cable, ISI marked with and inclussive of suitable size PVC rigid counduit concealed to wall, and PVC wire of size 4x10sqmm for phase and neutral duly colour coded and 1x10 sqmm for earth continuity conductor green in colour submain wiring complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 2.5 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 20 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old unserviceable submain wiring and wooden battens / conduits / casing capping and making good the disturbed surfaces all as per existing complete all as specified and as directed. Note: 3 runs of 2.5 Sq.mm & one run of 20 mm dia PVC Conduit will be measured as one unit.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 20 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old unserviceable submain wiring and wooden battens / conduits / casing capping and making good the disturbed surfaces all as per existing complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of 20 mm dia PVC Conduit will be measured as one unit.

Supply and fixing concealed in wall Vertical MCCB DB double door type, VTPN 8 way 415V, 50Hz , IP 43 protection with 200A rated bus bar , including provision for fixing MCCB FP 125-160 amp as incommer and outgoing circuits MCB SP/TP complete, fill empty way with blanking plates and including taking down old unserviceable DBs complete all as specefied and directed. Note : MCCB and MCBs shall be measured and paid seperately.

S & F TPN DB 6 Way having Powder coated sheet steel enclosure fitted with bus bar, DIN Channel & neutral link & earth link complete all as specified and as directed.

S & F MCB DB, SPN, 8 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB DB, SPN, 4 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB, SPN, 6 to 32 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, TPN, 40 Amps, 10 KA, C Curve, AC, 240 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, TP, 63 Amps, 10 KA, C Curve, AC, 240 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCCB 415 V, 50Hz , 16 KA, 4 Pole, 125 Amps capacity complete all as specified and as directed.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 4 mm GI Wire [Earth Lead] and GI pipe 15 mm, Light Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, rock Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 15 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. and disconnecting and taking down existing Earthing of any description complete all as specified and as directed.

S & F TV outlet socket with metal box minicomplete all as specified and as directed. Make :Anchor Cat No 21157 or euivalent in approved make.

S & F Telephonic jack deluxe with shutter single line with metal box complete all as specified and as directed. Model No. 20857 Make : Anchor or euivalent in approved make.

S & F computer jack Cat 6 with shutter with metal box mini complete all as specified and as directed. Make : Anchor Cat No 35220 or euivalent in approved make.

Supply and fixing PVC junction box with top cover of approx size 10cm x 7.5 cm rectangular type concealed to wall to for end termination/jointing for TV cable.complete all as specified and as directed.

S & F Rigid non-metalic 20 mm dia PVC conduit exclusive of boxes(junction/terminal) but inclusive of all tees, bends, elbows, reducer, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles pipe hook etc. complete all as specified and as directed.

Taking down Electric Meter of any description from its position and refixing the same with after repairs to buildings, at same place or at new place including connecting up complete all as specified and directed.

S & F hot press moulded SMC meter box of size suitable for housing of 3 phase electric energy meter, conforming to relevant IS, with viewing glass, hinged door and earth bolt, mounted on pole/ wall with seals suitable clamps/ bolts/ nuts complete all as specified and as directed.

S & F in repairs Lamp Holder, PVC/ Polycarbonate type with backplate suitable for batten fitting complete all as specified and as directed.

S & F in LED Bulb, 9 Watts Lumen ≥ 900, Luminous afficacy ≥ 100 Lum/Watt, CCT:WW/NW/CW, CRI > 80 Ra, IP 20 rated, complete all as specified and directed.

Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size including taking existing light complete all as specified and directed.

S & F LED light fitting 1x9W/1X10W bulkhead,luminaires including LED light driver holder,connecting up with three core flexible copper,conductor cable of suitable size including taking existing led light complete all as specified and directed.

S & F in repairs Stationary Louvers suitable for Exhaust Fan of 300mm sweep made out of powder coated aluminium anodized sheet of minimum 1 mm thick with non removable blades fixed permanently at 45 degree angle for protection from rain including aluminium wire mess for protection of birds complete all as specified and as directed. (Note: Louver has to fixed upto twenty metre height multistoried building. The unit quoted rate shall deemed to be inclusive of necessary scafolding and safety measure for fixing of louver upto twenty metre height. No extra claim on this account shall be entertained.

S & F Aluminium Strip of size 25 X 3.15 mm, fixed to walls / columns / beams etc with Saddles or porcelain blocks of 10mm thick spaced at 1.00m centre to centre including making grooves and fixing with brass screws etc. for roof conductors and down conductors above ground complete all as specified and as directed.

Fixing only in repairs Aluminium Strip of size 25 X 3.15 mm, fixed to walls / columns / beams etc with Saddles or porcelain blocks of 10mm thick spaced at 1.00m centre to centre including making grooves and fixing with brass screws etc. for roof conductors and down conductors above ground complete all as specified and as directed.

S & F Single Pointed Air Termination Aluminium Rod 12 mm dia and 300 mm long including necessary fasteners fixed for Lighting Protection with necessary connections to earthing etc complete all as specified and as directed.

Fixing only serviceable Air termination Aluminium Rods 12 mm dia 300 mm long complete all as specified and as directed.

S & F in repairs Earth continuity conductor or main earthing lead made of GI Strip of size 32 X 6mm, fixed to wall on batten or recess or chases or burried in ground or fixed to poles or any other indicated situation including drawing through GI Pipe for earthing etc. complete all as specified and as directed.

M&L for plain Cement concrete 1:2:4 type B-1, (Using 20 mm graded aggregate) as in foundation block for fixing GI pipe for installation of air termination rod etc. complete all as specified Note:- Unit rates includes for provn of form work for rough finished surfaces and finishing the exposed surfaces with 5 mm thick rendering in CM 1:3 complete all as specified and as directed.

Supply & Fixing GI pipe medium grade 40 mm dia for fixing Aluminium strip 25x3.15 mm on roof for lightening protection duly drilling 2 Nos holes on Aluminum strip and GI pipe on one end and fixing with screws/suitable size of bolts & nuts including taking down existing unserviceable pipe complete all as specified and as directed. Note: GI Strip required will measured and paid separately.

Supply and fixing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hexagonal head screws including provision of 30 cmx25cmx8cm sheet metal box made out of 3.15 m thick CRCA sheet with front hinged door shutter & locking arrangement and duly painted with two coats of synthetic enamelled paint over a coat of red oxide primer including taking down existing unserviceable test terminal box complete all as specified and directed

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 40 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Rock Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 40 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. including taking down of existing earthing set complete all as specified.

Supply, install, testing and commissioning of Integral LED aviation light of min 10 watts single head type comprising of aluminium housing with polycarbonate enclosure complete with connected flexible copper conductor cable incl loop-in-loop out box including taking down existing unserviceable light complete all as specified and as directed.

Taking down Aluminium strip 25 x 3.15mm with saddles and screws etc. from roof complete all as specified and as directed.

Taking down Air termination Aluminium Rods 12 mm dia 300 mm long complete all as specified and as directed.

srisampathassociates (BID ID -3423423)

MOUNIKA ENTERPRISES (BID ID -3426508)

VIJAY VINAYAKA INFRA (BID ID -3427593)

VENKATA SAI SRINIVASA CONSTRUCTIONS PRIVATE LIMITED (BID ID -3427512)

anjaliinfratech (BID ID -3427478)

GAGANSRI INFRA (BID ID -3428297)

CHAITANYA CONSTRUCTIONS (BID ID -3427886)

SREE CONSTRUCTIONS (BID ID -3428205)