SPECIAL REPAIR TO OR LIVING AT ARTY BDE AND TOILETS OF ENGR REGT UNDER GE MISAMARI

Amount

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level), complete all as specified and as directed. (Note:Demolished material to be used for filling under floors to bring upto required level, if neccesary)

Taking down Shutter of any description, not exc 1.00 Sqm Each, complete all as specified and as directed.

Taking down Chowkat or Frame (without taking off Shutter from the Frame) not exc. 1.50 Square Metre Each,,complete all as specified and as directed.

Taking down Chowkat or Frame (without taking off Shutter from the Frame) exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), removing from the Sites and rubbish off the Premises, complete all as specified and as directed.

Dismantling AC Corrugated/ Semi corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards /Blankets/Slabs, any description and any thickness including Cover Fillets, Cornices, etc., complete all as specified and as directed.

Dismantling Timber Scantling 40 Sq Cm and over in Section in any position in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillet, Rails, Posts, Rafter, Purlins, etc. under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc., complete all as specified and as directed.

Excavation in trenches not exc. 1.5 Metre Wide and not exc. 1.50 Metre in Depth for foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes for laying of UG Cable/Pole/Stays etc, and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 25 Cm in Soft/Loose Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point in Soil, complete all as specified and as directed.

M&L Non skid ceramic coloured jointless tiles/matt finished coloured ceramic tiles 7 to 8mm thick (Square/ Rectangular) area of each tiles exceeding 0.06 Sqm but n.exc. 0.11 Sqm in floors etc. over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified and as directed.

M&L Non skid ceramic coloured jointless tiles/matt finished coloured ceramic tiles 7 to 8mm thick (Square/ Rectangular) area of each tiles exceeding 0.18 Sqm but n.exc. 0.38 Sqm in floors etc. over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified and as directed.

M&L glazed ceramic coloured tiles, glossy finished of size 350x450x7mm/ 350x250x7mm thick as in vertical surfaces such as skirting/dados and riser of steps., over and including including 10 mm thick rendering/backing coat in CM 1:4 and set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles,complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 (External) on Fair Faces of Brick Walls or on Concrete Surfaces in Two Coats, 1st Coat of 10mm thick and 2nd Coat of 5mm thick including mixing with WPC to 2nd Coat as per Manufacturer's instructions, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE : Liquied Water Proofing Compound shall be Measured and Paid separately as ‘Supply only’ under relevant Items.

M&L Rendering 15mm thick in Cement Mortar 1:6 on other side of lathing 1st Coat of 10mm thick and 2nd Coat of 5mm thick including mixing with WPC to 2nd Coat as per Manufacturer's instructions, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE : Liquied Water Proofing Compound shall be Measured and Paid separately as ‘Supply only’ under relevant Items.

M&L Rendering 15mm thick in Cement Mortar 1:4 on one side of lathing 1st Coat of 10mm thick and 2nd Coat of 5mm thick including mixing with WPC to 2nd Coat as per Manufacturer's instructions, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE : Liquied Water Proofing Compound shall be Measured and Paid separately as ‘Supply only’ under relevant Items.

M&L Rendering 5mm thick in Cement Mortar 1:3 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

Supply only liquied Water Proofing Compound, as approved, complete all as specified and as directed.

M&L preparing newly plastered surfaces of wall and applying Three Coats of White Wash, complete all as specified and as directed

M&L preparing newly plastered surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed

M&L preparing new Plastered Surfaces of Walls and applying Two Coats of Cement Base Paint over a chalk whitening, complete all as specified and as directed.

M&L preparing new Plastered Surfaces of Walls and applying Two Coats of Cement Base Paint over a coat of cement primer, complete all as specified and as directed.

M&L preparing old Plastered Surfaces of Walls and applying one Coats of Cement Base Paint , complete all as specified and as directed.

M&L preparing new Plastered Surfaces of Walls and applying Two Coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L preparing old Plastered Surfaces of Walls and applying one Coats of distemper oil emulsion, complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of size 50x47 mm made out of 5.0 mm thick plain colour PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S & F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles),with 2,4or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet painted on the front face and 2mm thick plain colour PVC sheet on back face complete all as specified and as directed.

S & F Anodised aluminium window and ventilator shutters,fixed type without sash bar,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, handles, screws, anodised aluminium fitting such as peg stays 150 mm long(1 no.) hinges type B-21 100 mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed. NOTE:- (i) Fixing of shutter with fitting shall be as per manufacturers instruction (ii) Rate quoted is deemed to be inclusive of aluminum hardwares as indicated, glazing clips, rubber packing, anodized aluminum snap on beading for fixing glass panes in frame, handles, Locking Arrangement but Glass panes in frame shall be measured and paid separately under respective Sch A items separately at Supply only rates)

M&L Figured Glass, pin headed type, 3.0mm thick, Glazing in Wooden/Metal Frames and glazed with Beads or Oil Putty, area not exc. 0.50 SQM in Each Pane, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt 100 mm long, Extruded Section and fixed, complete all as specified and as directed.

All as per Item no.34 here in before but for 150 mm, complete all as specified and directed.

All as per Item no.34 here in before but for 200 mm, complete all as specified and directed.

S&F Aluminium Handle 150mm long Cast type, complete all as specified and as directed.

All as per Item no.37 here in before but for 100 mm, complete all as specified and directed.

S&F for 100mm size aluminium alloy anodised hinges, complete all as specified and directed.

S&F Mild Steel Sliding Door Bolt 250 mm long, Plate type, Black Japanned Finish with bright Bolt not less than 12mm dia, minimum 6 Bolts and Nuts 4 on Bolt Plate 2 on Staple Plate and fixed, complete all as specified and as directed.

All as per Item no.40 here in before but for 300 mm, complete all as specified and directed.

S&F Ordinary Rat Tail 300mm, Rod Pattern Springs including Roller and Roller Plate and fixed, complete all as specified and as directed.

M&L Cement Concrete type B-0 1:2:4 (12.5 mm stone aggregate) 25mm thick in Roof Padding, including demolition of cement concrete of any description and in any situation, complete all as specified and as directed.

M&L Cement Concrete type B-0 1:2:4 (12.5 mm stone aggregate) 25mm thick in floor, complete all as specified and as directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Rendering 10mm thick in Cement Mortar 1:4, Plastered Surfaces finished Even and Smooth. The Plastered Surfaces shall be cured properly for 7 DAYS by Ponding of Water over Roof. (b) Preparing and cleaning of fully dry Plastered Surfaces as per IS:3067-1966. (c) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.30 Litre per Square Metre. (d) Applying a layer of APP based Polymeric Membrance 3.0mm thick (minimum) weighing 3.50 Kilogram per Square Metre (reinforced) with Polyster Non-woven Fabric weighing not less than 160 Gram per Square Metre by Torch application. The Overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. (f) Applying One Coat of Aluminium Paint @ 0.10 Litre per Square Metre over APP based Polymeric Membrane.

Supply & laying Steel Water Tubing 15mm bore (dia), galvanised, ‘medium grade’ with all Fittings, fixed on walls, ceiling or laid in floors or any other situation and including taking up or down existing steel water tubing, complete as all specified and as directed.

Supply & laying Steel Water Tubing 20mm bore (dia), galvanised, ‘medium grade’ with all Fittings, fixed on walls, ceiling or laid in floors or any other situation and including taking up or down existing steel water tubing, complete as all specified and as directed.

S&F in repair bib tap 15mm bore (dia) Fancy Type, Cast Copper Alloy, Chromium Plated with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed, complete all as specified and as directed.

S&F in repair Pillar Tap 15mm bore (dia), Cast Copper Alloy, Chromium Plated with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and fixed, complete all as specified and as directed.

S&F in repair concealed stop cock 15mm bore , Chromium Plated with long shank, fancy type, screwed down high pressure with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions and fixed, complete all as specified and as directed.

S&F in repair 15mm bore angular stop Cock with Wall Flange, complete as all specified and as directed.

S&F in repair Brass Chromium plated Shower Rose 125mm size, with or without Swivel Joints, and fixing to Steel Pipe or Union and fixed, complete all as specified and as directed.

S&F in repair Brass Chromium plated Tubular Towel Rail, 20mm dia, D-type, 60 Cm long between Flanges with Bracket (one Pair) and fixed, complete all as specified and as directed.

S&F in repair PVC Connection Pipe 15mm in size with PTMT Nuts of length 450mm and fixed, complete all as specified and as directed.

S & F in repair PVC waste pipe of 32 mm bore of adequate length complete all as specified and as directed.

S&F in repair, Sheet Glass Shelf/corner Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and as directed. .

S&F in repair vitreous china Soap Dish holder of size 160x160x90mm complete all as specified and directed.

S&F in repair Vitreous China White Squatting Pan, ‘Orissa’ Pattern of size 580x440 mm with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and fixed, complete all as specified and as directed.

M&L Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Trap and Fixing Bolts (excluding Flushing Cistern and Flush Pipe) including connection to drain (or outgoing pipe) and to Flushing Pipe, Anti-syphonage Pipe, etc. and Making Good to Floor /distrubed surfaces and fixed-in-repair including health faucet with 1mtr long easy flex tube in chrom finish & wall hook, complete all as specified and as directed.

S&F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, valve less, syphonic action type with Inlet, Ball Valve, Float and handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed, complete all as specified and as directed.

S&F in repair Vitreous China Wash Hand Basin 550x 400mm in size, White (Flat Back or Angle Back Type) with 32mm bore waste coupling of PTMT (half or full threaded of minium weight 32-445gms), a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including Cutting and Pinning in Ends, Making Good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F in repair Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity (Cylindrical, Vertical with Closed Top), 3 layered, hoisted and fixed in Position all as specified in MES Scheduleincluding wash out GI Pipe 32mm of 450mm length with stopper, complete all as specified and as directed. , complete all as specified and as directed.

S&F in repair PTMT grating Doom 125mm dia (minimum weight 40 Grams) complete all as specified and as directed.

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors complete all as specified and as directed.

All as per Item no.65 here in before but for 110 mm, complete all as specified and directed.

M&L for sunken floor treatment as in following precedence (i) Provide 40mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in sub base and provide 40mm dia GI pipe med gde as in (spout) of 600mm long as in sunken portion. (ii) The treatment of existing sunken floor is to be dismantled upto full depth of Sunken RCC Slab and the surfaces both vertical and horizontal shall be cleaned by removing all loose dust etc., apply two coats of elastomeric compound back bond WPC-30 over one coat on neat primer i.e. Super latex be applied on clean surface. (iii) Rendering 15mm thick in CM 1:3 using liquid water proofing compound @ rate 200 ml per bag of cement on horizontal and vertical surfaces of sunken portion. Note: Water proofing compound shall be measured and paid separately. (iv) Fill the remaining suken portion with PCC 1:5:10 using brick aggregates including fixing sanitary items requiring embedding in cement concrete. (v) The suken floor tested for leakage/seepage by ponding with water for minium 48 hours to ensure no seepage/dampness is seen underneath and side.

M&L 75mm thick Cement Concrete 1:4:8, type D2 (40mm graded aggregate), as in Sub-base finishing Concrete Surfaces Even and rough, complete all as specified and as directed.

M&L Cement Concrete 1:3:6, C2 (40mm graded aggregate), 75mm thick as in Plinth Protection, etc., laid in alternate bays, finishing Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

S&F in repairs GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding, fixed with self tapping screws as specified, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and as directed.

M&L for GI Frame Work (Size of grid 605x605mm) for Seamless Ceiling comprising of GI Perimeter Channnel 0.55mm thick with Two Unequal Flanges of 20 and 30mm and Web of 27mm fixed to surrounding Wall using Nylon Sleeves and Screws at 450 mm Centre to Centre/ Intermediate Channel 0.9mm thick having Two Equal Flanges of 15mm each and Web of 45mm suspended from Soffit at approx 900mm centre to centre with GI Cleat and Steel Expansion Fasteners with and including Ceiling Section (not exc 1.20 Metre length) of 0.55mm thickness having Kurled Web of 50mm and Flange of 26mm each with Lips of 10.5mm fixed to the Interme-diate Channel with Connecting Clips across the Intermediate Channel at 457mm Centre to Centre, complete all as specified and as directed.

S & F for 4mm thick designer Non asbestos fibre cement building boards prepainted fixed to GI snap grid in ceiling flat complete all as specified and as directed.

S&F 6 mm thick, Plywood, grade BWR, type BB, fixed with screws to timber frame work, complete all as specified and as directed.

M&L Second Class Hardwood in Scantlings Wrought Timber Framed and fixed complete all as specified and as directed.

All as per item no. 76 here in before but except hardwood in scantling, complete all as specified and as directed.

M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in Section Clean sawn, secured with Nails, sectional area exc. 6 Sq Cm but not exc.13 SqCm , complete all as specified and as directed.

Refixing shutters of any description n exc 1 sqm in same opening complete all as specified and as directed.

M&L Factory Made Second Class Hardwood 30mm thick Glazed and Skelton Shutters, open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars) edges of Framing plain, chamfered or rounded, mitred beads for screwing Glass, Gauge, etc. sizes of members of Shutter as speci fied in MES Schedule Part-I Section 8, Clause No. 8.24(a) and fitted to Wooden Chowkat, complete all as specified and as directed.

All as per Item no.80 here in before but for 35 mm, complete all as specified and directed.

M&L Factory Made Second Class Hardwood Rail and Style, 35 mm thick Plain Framed Panelled Door Shutter (Single Panel) with Lock Rail and Panel of 9mm BWP Commerical Ply or 12mm Venerred Particle Board with commercial veneering on both faces. The size of rails and stiles as per IS: 1003 (Part I), klin seasoned and chemically pressure treated and fixing to Chowkat, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 100mm, medium weight, cold rolled and fixed, complete all as specified and as directed

All as per Item no.83 here in before but for 75 mm, complete all as specified and directed.

S&F in repair Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and fixed, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and fixed, complete all as specified and as directed.

M&L Chequered Cement Concrete Tiles 200x200x25mm thick laid over 15mm thick in CM 1:6 in Floors, etc., set, jointed and pointed in Neat Cement Slurry in Floors with Grey Cement and Pigment, complete all as specified and as directed.

M&L preparing new or previously untreated Steel and Iron Surfaces of any description, over. 10 Cm Width or Girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L preparing new or previously untreated Wooden Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

S & F in repair Harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified and as directed.

M&L applying a coat of 3 mm thick wall care putty as per manufacture instruction complete complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., conforming to Fe 410-W (Gde E-250) quality A, drilled for fixing of steel sheeting or other covering Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening,complete all as specified and as directed.

M&L 4 mm dia Plain mild steel wire, galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) and fixed incl taking down existing old wire , complete all as specified and as directed.

Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) of any description on batten/conduit and making good disturbed surfaces of Ceiling, Walls, etc. in Cement Mortar 1:3 and providing Surface Treatment so as to match the existing Finishes, complete all as specified and as directed.

Taking down the existing unservicable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down fan, sealing cable end,dismantling blades and removing fan and blades to store to keep it in safe custody for refixing,complete all as specified and as directed.

Taking down ceiling fan of any sweep, keeping with safe custody and refixing the same with replacement of unserviceable 3 core PVC insulated, PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal, Overhauling the fan, complete all as specified and as directed.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes,complete all as specified and as directed.

Taking down the existing unservicable UG cable of any type/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M&L Point Wiring with 1.5 Sqmm Copper Conductor single core PVC insulated Flame Retardant (FR) Unsheathed 1100 Volt grade multi-stranded Cable drawn through and including PVC Casing and Caping high grade of suitable size and its Accessories, mounted on 1.22 mm thick Sunk Mild Steel Pressed Terminal Box of suitable size duly painted with red oxide metal primer fixing/ grouting sunken/surface as per Site requirement on Wall and making good in Cement Mortar 1:3 with 3.0mm thick bakelite hylem Sheet Top Cover for mounting Switches, Sockets, etc. including PVC insulated and unsheathed Single Core multi-stranded Copper Conductor Cable of size 1.5 Sqmm Green in Colour as Earth Continuity Conductor connected to Common Earth and Earth dolly for One Light Point controlled by One 1-Way Switch 5 Amp, complete all as specified and as directed.

All as per Item no.100 but for One Ceiling Fan/Exhaust Fan Point controlled by One 1-Way Switch 5 Amp and Regulator, complete all as specified and as directed.

All as per Item no.100 here in before but for One 3 Pin 5 Amps Switch Socket Outlet Point controlled by One Switch on Same Board, complete all as specified and as directed.

All as per Item no. 100 here in before but or One 3 Pin 5 Amps Switch Socket Outlet Point controlled by One Switch on Independent Board, complete all as specified and as directed

All as per item No 100 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point incl running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

S&F Switch Piano, Flush type, Single Pole, 1-Way, 5 Amps, 240 Volt, conforming to IS and connecting up, complete all as specified and as directed complete all as specified and as directed

S&F Socket Outlet, 2-in-1, 2/3 Pin, 5 Amp, 230 Volt, conforming to IS and connecting up, complete all as specified and as directed.

S&F Ceiling Rose, Surface Bakelite of size 65x50mm, 3 Terminals, AC, 50 Hz, 240 Volts, conforming to IS and connecting up, complete all as specified and as directed.

S & F wall mounted LED 18 watts , box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 18 watts complete all as specified and as directed. Make-Model -REGALBATTENT5UPTO1X18WDSBSWH For Batten Fitting and Model-PHOTONULTRAE2.01213T8SSTL18WLED865SPC For T8 Tubelight ,Make Havells, or equivalent in CG, Polycab.

S&F Lamp Holder Surface Bakelite with Back Plate insulated body suitable for Batten/Angle Fittings and fixed with PVC Block, conforming to IS and connecting up, complete all as specified and as directed.

S& F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.Make-Make- Havells, Cat No: LHLDEUEBML8Z010 or equivalent in CG or Polycab.

S&F Sheet Metal Enclosure MCB DB, SPN, 4-way with 200 Amp rated Bus-bar, 240 Volt, Double Doors with Magnitic Locking System and connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure MCB DB, SPN, 8-way with 200 Amp rated Bus-bar, 240 Volt, Double Doors with Magnitic Locking System and connecting up, complete all as specified and as directed.Make:- Legrand/L&T Model No -DBTPN008DD or equivalent in Schinder/ Legrand.

S&F MCB SP,6-32 Amps, 240 Volt for fixing on MCB DB’s, 10 kA,c curve 50 Hz, conforming to IS/IEC 60898 and connecting up, complete all as specified and as directed.(Make- L&T, Cat No: BB10320C ,Havels & Legrand.)

S&F MCB Double Pole, 32 Amps, 240/415 Volt for fixing on MCB DB’s, 10 kA,c curve 50 Hz, conforming to IS/IEC 60898 and connecting up, complete all as specified and as directed.(Make- L&T, Cat No: BB20320C ,Havels & Legrand.)

Fixing only exaust fan (M.D. Supply) and connecting up including provision of cable from ceiling rose/connector to fan, complete all as specified and as directed

S&F Switch Socket Combination 2-in-1, Flush type, multi-purpose, 2/3 Pin, 5 Amp, 240 Volt, conforming to IS and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 2-in-1, Flush type, multi-purpose, 3/5 Pin, 5/15 Amp, 240 Volt, conforming to IS and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Step type, Flush type, heavy duty, suitable to work on 230 Volt, AC supply and connecting up, complete all as specified and as directed.

S&F Blanking plates half module suitable for DBs,complete all as specified and as directed. : Make- L&T,Cat No- BKP05

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 15 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Havells,Model No - ENDURAPEARLSL15WLED757SASYTOPCMP Or Equivalent in CG and Polycab all as specified and directed.

M & L for sub main wiring with two single runs of single core 6.0 sqmm PVC insulated unsheathed multisreanded 1100 volts grade with copper conductor drawn through and including PVC casing caping ISI marked and its accessories including one run of single core 6.0 Sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth contuinity conductor along with the wiring and connected from DB to DB/ main board complete all as specified.

M&L Sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 230mm Spread thickness (8 Cm in depth before laying Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : Only Punned thickness of Sand Cushioning will be measured for Payment.

S&F Sub-Class ‘B’ Brick, well burnt, laid breadth-wise along the length of Cable laid in Trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed.

Supply & laying LT UG XLPE sheathed PVC insulated, screened PVC bedded, Galvanised Steel Strip of Wire armoured Electric Power Cable heavy duty with stranded Aluminium Conductor 1100 Volt grade, cross-sectional area 16 Sqmm 2.00 Core, laid in trenches /surface of Wall/in GI Pipe along with Pole including Brass Cable Glands Mild Steel Flat Iron Clamps, etc. including making good to the damaged surfaces to match as per existing surfaces, complete all as specified and as directed. NOTE : Earthwork, Horizontal Boring Road/ Foot Path, Cable Protection Pipe, Cable Joint, Mild Steel Clamps, Nuts & Bolts, etc. for fixing of Cable Protection Pipe with Pole, Wall, etc.(as required) will be measured and paid for separately under appropriate Items.

Supply & laying Steel Water Tubing 40mm bore (dia), Galvanised, ‘light grade’ with all Fittings,in protection of cable at road crossing/hard standing/pole protection fixed with clam as per site or any other situation, complete as all specified and as directed.

M&L Earthing with Galvanised Steel Earth Plate Electrode 600x600x6mm, buried directly in ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 6.0 mm dia by means of Bolts, Nuts, Check Nuts and Washers of GI or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) ‘light grade’ upto 1.0 Metre above the Floor Level of Building where Main Switch/DB situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc 150mm thick PCC Pit in Cement Concrete 1:3:6 (20 mm graded aggregate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded aggregate), reinforced with 8mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) ‘medium grade’ including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on completion, complete all as specified and as directed.

M/S Mahabir Traders

M/S Himalayan Trading Co

Markson

R D ENTERPRISE