Revamping of existing Illumination system of Matla Bridge with approach road at Canning, south 24 Parganas.

Feeder Pillar Box : Design, Manufacture, testing, supply and commissioning of Double door outdoor type Distribution Feeder Pillar box (H x W x B) (1000mmx860 mm x 600mm approx ) conforming to Indian Standard IS : 5039- 1969 with latest amendments,suitable for use on 3 phase 4 wire, 400/440 Volts 50 Cycles A.C. Supply and shall be suitable to be fabricated as per design & drawing to be approved by EIC. The Enclosure shall provide Degree of protection IP -66 respective Indian standard (IS). [Manufacturer/Fabricator having Test Certificates from CPRI] The body will be fabricated with 3mm thick MS plate, MS angle ( 40X40X5) & MS Flat ( 50X6 ). The top of the box will be fitted with a sloping canopy made out of 5 mm thick sheet steel. It will have double hinged door at the front and back with suitable locking arrangement (Godrej Type ) and provision for manual locking arrangement also.

Provision for Fixing WBSEDCL Meter : i) Hylam/Bakelite Sheet; size: 600mm x 600mm x 12mm (H x W x Thickness) ---- 1set. ii) 415v; 63A porcelain Kit Kat Fuse unit --- 3nos. iii) 415V; 63A nuutral link --- 1 no. inter connection should be done by suitable Cu wire (mini. size 4 core, 16 sq. mm.).

Incomer : i) 415V, 63A, FP MCCB of Breaking capacity 25kA/35kA with adjustable thermal and fixed magnetic setting (Make – LK (L&T) / Havells / SIEMENS / ABB) -- 01 No. ii) Bus-Bar : Cu 4 bars 415V, 63A. iii) LED indicator Lamp (R/Y/B) - 03 nos. iv) Danger Board

Out Going: i) 415V, 16A FP Power Contactor (Make: LK (L&T) / Havells / Legrand / SIEMENS /ABB) -- 02 nos. ii) 415V, 16A FP MCB (Make: LK (L&T) / Havells / Legrand / SIEMENS / ABB) -- 02 nos. iii) Digital Astronomical Time Switch (Make –LK (L&T) / Havells / ABB / Siemens) -- 02 nos. iv) Auto Manual Selector Switch -- 02 nos. v) ON/OFF Push Button -- 04 nos. vi) ON/OFF LED Indication Lamp -- 04 nos.

Interconnection :- All interconnection between incoming main to Busbar are to be made with suitable size flexible pvc insulated multistranded single core Cu cable and the same between busbar to each outgoing MCBs with proper socketing of the end of each wire leads.

Earthing Arrangement :- A separate continuous aluminum earth busbar of appropriate size is to be painted at the inside bottom of the panel and run across the full load of the Feeder Pillar Box. All electrical equipment are to be properly earthed with suitable size G.I. strip.

The complete Feeder Pillar Box is to be spray painted after required surface treatment by 7 tanks process / sand blasting with 2 coat of red oxide primer & 2 coat of finished paint over dried or powder coating.

Installation :- The complete feeder pillar box board is to be installed on suitable brick padestal as directed by the E.I.C.

Dismentling charge of damaged 9mtr. Swan neck type MS tubular pole & installation the same after minor repair with co's own tools and tackles

Erection of Single Steel tubular pole of length as given below with/without sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly