PROVN OF PARKING SHED FOR HQ TASA COMPLEX NEAR BLDG NO.A2, REPAIRS TO SEPTIC TANK,SEWAGE LINE NEAR TRAINING AREA AT HQ TASA AND PROVN OF 3 TOILET AND WASH ROOM AT BLDG NO.PL 55 ADM BLOCK UNDER AGE BR (N) NO. I AND AGE BR (N) NO.II OF GE (NORTH) SECUN

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep getting out in hard/dense soil complete all as specified and directed.

Cleaning away all grass, vegetation, saplings, shrubs, bush-wood, under growth and roots for making approach to the working area and removing the rubbish to a distance of 50 metres outside the periphery of area complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundations,laying of drain pipes,manholes, laying cables,etc and getting out in hard/dense soil complete all as specified and directed.

All as per item No.4 above but exc 1.5 m deep and n. exc 3 m deep and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm in any type of soil complete all as specified and directed.

Removing excavated material to a distance not exc. 50 m and depositing where directed at a level n. exc. 1.50m above the starting point complete all as specified and directed.

Excavating in post holes as in soft/loose soil (or similr holes) not exc0.5 Cum getting out returning filling in and reamming earth or broken rubble mixed with earth around, in lyers not exceeding 25 Cum watering and removing surplus soil to a distance no exc 50m and making good surfaces complete all as specified and directed.

M&L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with back fill to be measured) complete all as specified and directed.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per sqm of surface complete all as specified and directed.

M&L Treating the soil under plinth protection at the rate of 5 litres of emulsion per sqm of surface area complete all as specified and directed.

M&L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

Demolition of RCC in ground floors and pavings not exceeding 15 cm thick (below or above ground level) including removing debris beyond the premises complete all as specified and as directed.

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided including roof padding concrete and removing debris beyond the premises complete all as specified and as directed.

M&L PCC (1:4:8), type D-2, (using 40mm graded stone aggregates) as in foundations, filling, mass concrete etc complete all as specified and directed.

M&L PCC (1:3:6), type C-2, (using 40mm graded stone aggregates) as in foundations, filling, mass concrete etc complete all as specified and directed.

M&L PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in coping including necessary formwork, weathering, slighty rounded or chamfered angles and throating etc complete all as specified and as directed.

M & L PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in coping, benching of manholes, drains and surface channels etc., including necessary formwork, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L Pre cast RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in cover slabs for manholes, and set in CM (1:4) including necessary formwork complete all as specified and directed.

M&L Providing RCC (1:2:4) type B1 (using 20mm nominal size graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns,etc; basement slabs, comlpete all as specified and directed..

M&L Providing RCC (1:2:4) type B1 (using 20mm nominal size graded stone aggregate) as in columns, pillars, piers, posts and struts etc. complete all as specified and directed.

M&L Providing RCC (1:2:4) type B1 (using 20mm nominal size graded stone aggregate) as in beams, cantilevers bressummers lintels over 1.5 m span,etc complete all as specified and directed.

M&L Providing RCC (1:2:4) type B1 (using 20mm nominal size graded stone aggregate) as in chajjas complete all as specified and directed.

M&L Providing RCC (1:2:4) type B1 (using 20mm nominal size graded crushed stone aggregate) as in slabs supported on walls, beams and columns complete all as specified and directed.

M & L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified and directed.

Use and waste of formwork to sides of concrete foundation, footings, base of coloumns, raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, coloumns and stanchions for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams,lintels,beam haunching,etc for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of formwork with rough finished flat concrete faces as soffits of suspended slab such as roof slabs, floor slabs, landing & similar work complete all as specified and as directed.

Use and waste of formwork to edges of conrete flats,treads,breaks in floors,opening in concrete walls,floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in walls,horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide for rough finished flat surfaces of concrete complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar with all quoins, arches, pillars, etc but excluding ashlar facings, dressed stone work and precast concrete articles including disposal of the rubbish out off the premises complete all as specified and as directed.

M & L Precast cement concrete block masonry with solid blocks exceeding 10cm in width by using precast cement concrete (1:3:6) type C1 (using 20 mm graded stone aggregate) and set in CM (1:6) complete all as specified and directed.

M&L Brickwork with fly ash bricks (using old size bricks) straight or curved on plan exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

M&L Brickwork with fly ash bricks (using modular bricks) straight or curved on plan exc 6 m mean radius built in CM (1:6) complete all as specified and directed.

M&L Brickwork with fly ash bricks (using modular bricks) straight or curved on plan exc 6 m mean radius built in CM (1:4) complete all as specified and directed.

M&L Brick work with fly ash bricks modular bricks, straight or curved on plan exceeding 6.0 metre mean radius in half brick thick walls built in CM (1:6) complete all as specified and as directed.

M&L Brick work with fly ash bricks old size, straight or curved on plan exceeding 6.0 metre mean radius in half brick thick walls built in CM (1:4) complete all as specified and as directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and directed.

All as per Item No.39 above, but 6 to 8 mm dia complete all as specified and directed

All as per Item No.39 above, but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, complete all as specified and directed

S&F Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240 complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk forming holes, without any attachment etc.Roof strusses (framed) and connecting plates, etc., including necessary precautionary measures as in supports etc., complete all as specified and as directed.

S&F Wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 etc complete all as specified and directed.

S&F for Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating galvanised based corrugated steel sheet of 0.50 mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping (SD) screws complete all as specified and as directed

S&F Pre-painted galvalume aluminium zinc coating galvanised based profiled/plain steel sheet 0.50mm thick, AZ-150 of approved colour having tensile strength of 550 Mpa as in ridge, gutters fixed with self tapping (SD) screws complete all as specified and as directed.

S & F Fixed Louvered Ventilators made of pre - painted steel (base steel as per IS 513 of -0.58 mm thick 'D" quality, galvanized as per IS 277 with zinc of 120 GSM) primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer, The section for louvered ventilators should be of 33 x 56 mm Box section panelled with 4 mm pinhead glass with Ethyl propylene Diamine monomer Gasket (EPDM) and the sections cut to length mitre joined with corner bracket . Corner brackets made of CRCA with Zinc Phosphate. The frames to be fixed to the concrete/masonry wall by means of self expanding screws including 10 mm square guard bars with 6" pitch complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners are included in this item ) Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately).

S&F 100 mm long Stainless Steel butt hinges fixed to PVC door shutter complete all as specified and as directed.

S&F 150mm long Stainless Steel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 150 mm long Stainless Steel handles fabricated type complete all as specified and as directed.

M & L Water proofing treatment to roof slab by applying one coat of bituminous / polymrised primer confirming to IS 3384 @ 0.30 ltr /sqm and laying grit finish Actetic Polypropylene (APP) modified membrane pre-fabricated , reinforced with non woven polyester , of 3.50 kg/sqm (minimum) , 3mm thick minimum with minimum 75mm side overlaps and minimum 100 mm end overlaps over and including 10mm thick rendering in CM(1:3 ) mixed with WPC as per manufacturers instructions complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings not exceeding 15 centimetre thickness (below or above ground level) complete all as specified and as directed.

M&L Hardcore of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface in broken stone or boulders complete all as specified and as directed.

M&L 25 mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sub base flooring complete all as specified and as directed.

M&L 75 mm thick PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in sub base to floor complete all as specified and as directed.

M&L 75 mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) in plinth protection laid in alternative bays finished even and smooth without using extra cement including making 10 mm wide grooves to full depth at 3 m interval and at every change of direction and filling the grooves with mixture of bitumen and sand mixed in the ratio of 1:3 by weight and top 10 mm depth sealed with sealing compound grade ‘A’ complete all as specified and as directed

M & L 100 mm thick PCC (1:2:4) type D-2 (using 40 mm graded crushed stone aggregate ) as in sub base flooring complete all as specified and as directed.

S&F Non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

S&F Glazed ceramic coloured tiles of size 300x200x7mm thick as in vertical surfaces skirting,dado,etc set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L Sand filling 50 mm thick under floor/ below interlocking paver blocks or in foundations including well ramming complete all as specified and directed.

M&L 60 mm thickness, Machine pressed precast concrete interlocking paver blocks, M-35 grade with grey cement and pigment (glossy finish) any shape and size conforming to IS 15658-2006 complete all as specified and as directed.

M&L Designer rubber moulded chequerred cement concrete tiles with mixture of grey and white cement in equal porportions with pigments of size 300 x 300 x 22mm or 250 x 250 x 22mm thick as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and directed.

Taking down cement plaster of any description and in any position of brick or stone wall/concrete surfaces on walls ,ceiling etc including raking out joints ,hacking for key scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed.

M&L Rendering 15 mm thick CM (1:6) on surfaces other than fair faces of brick/concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 10 mm thick CM (1:6) on surfaces other than fair faces of brick/concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 10 mm thick CM (1:4) on surfaces other than fair faces of brick/concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5 mm thick in CM (1:3) on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 15 mm thick CM (1:4) on fair faces of brick/concrete surfaces using with water proofing compound as per manufacturers instructions finished even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured & paid separately.

M&L Rendering 10 mm thick CM (1:3) on fair faces of brick/concrete surfaces using with water proofing compound as per manufacturers instructions finished even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured & paid separately.

Supply only Integral waterproofing compound.

M & L Preparing newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

M & L Preparing newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and as directed.

M & L Preparing newly plasterd wall surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L Preparation of new surfaces of steel, of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F CPVC pipes 16 mm dia, SDR 13.5 & Plain CPVC SDR 11 fittings laying in trenches complete all as specified and directed.

S&F CPVC pipes 20 mm dia, SDR 13.5 & Plain CPVC SDR 11 fittings laying in trenches complete all as specified and directed.

S&F CPVC pipes 25 mm dia, SDR 13.5 & Plain CPVC SDR 11 fittings laying in trenches complete all as specified and directed.

S&F Vitreous China, wash down water closet pan "Pedestal pattern" white including connection to drain and to flush pipe and anti syphonic pipe 10 ltrs capacity flush tank,600mm long Pvc Connection,, Two way cock, 1m length Healthfaucet set, including allnecesaary accessories and making good the disturbed surfaces complete all as specified and as directed.

S&F Viterous china wash hand basin white/coloured flat back size 630x450mm including waste coupling and PVC waste pipe, 32mm dia, 15 mm dia bore pipe pillar tap cast copper alloy with capstan heads chromium plated fancy type, to be fixed with M S brackets complete all as specified and as directed.

S & F Vitreous China full stall urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 15mm dia push tap for urinal cast copper chromium plated alloy with capastan head chromium plated screwed to iron pipe 60mm long brass screws, pointing around urinal back in cement; stopcock, 600mm long PVC Connection flush pipe, grating and Union for discharge pipe incl polished granite Partition urinal partition of size 310x700 mm complete all as specified and directed.

S&F 15 mm bore fancy type concealed stop cock (regular body) cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S & F 15 mm bore stop valve/angular valve,fancy type cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions .

S&F 15mm dia bib tap,CP fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

S & F Tubular towel rail 20 mm dia ‘D’ type 60 cm long between flanges of brass chromium plated complete all as specified and directed.

S&F 125mm dia brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F100 mm size soap dish,chromium plated fixed to wall with CP brass screws complete all as specified and as directed by Engineer-in-charge.

S&F in repair for glass shelf 450mm X 150mm X 8 mm thick with chromium plated railing fixed with and including chromium plated brackets complete all as specified and as directed.

S&F in repair for corner glass shelf of size 200mm dia and 8mm thick with chromium plated railing, fixed with and including chromium plated bracket complete all as specified and as directed.

S & F Grating square 150mm size of PTMT (minimum weight 100 gms) complete all as specified and directed.

S&F in repairs of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including necessary fixing arrangements, as in soil/waste/vent pipes complete all as specified and as directed

S&F in repairs of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laying in trenches or floors complete all as specified and as directed

S&F in repairs of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls including necessary fixing arrangements, as in soil/waste/vent pipes complete all as specified and as directed

S&F in repairs of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laying in trenches or floors complete all as specified and as directed

S&F in repairs 100 mm bore PVC (SWR) floor trap/Nahni trap, plain with grating including jointing to waste pipe fixed in PCC (1:2:4) type B1(using 20 mm graded stone aggregate) complete all as specified and as directed.

S&F PVC (SWR) floor trap 75 mm bore, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bend with oval access door of any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends with oval access door of any radius complete all as specified and directed.

S & F for 110 mm PVC (SWR) branch piece (Single Y or T) equal or unequal with access door complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tank 3 layer white colour waterr tank , non- toxic effect, algea formation protection (made from Virgin grade of polyetjylene material which is duly stablized with anti-oxidentPlastic) of capacity 1000 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer, 20mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) and stop valves for 20mm bore pipe, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends etc complete including dismantling existing water tank all as specified and directed. Make: Cat No: HSWS-0100-01-Pure of M/s. Sintex or Equivalent model in Polycon / Rolex / Astral Limited.

Demolition and breaking up drain pipes of size 150 mm dia (salt glazed ware AC or reinforced concrete) set in cement mortar complete all as specified and as directed

Demolition and breaking up drain pipes of size 200 mm dia (salt glazed ware AC or reinforced concrete) set in cement mortar complete all as specified and as directed

M&L RCC pipes, 150 mm bore,class NP3 laid in trenches with one collar per length and jointed with cement joints complete all as specified and as directed

M&L RCC pipes, 200 mm bore,class NP3 laid in trenches with one collar per length and jointed with cement joints complete all as specified and as directed

M&L RCC pipes, 200 mm bore,class NP2 laid in trenches with one collar per length and jointed with cement joints complete all as specified and as directedd

M&L Concrete bed to drain pipes of size 150 mm dia with using PCC ( 1:3:6) type C2 (using 40 mm graded stone aggregate) with necessary form work including packing under and haunching against the sides of pipes with concrete, after they are laid including testing, complete all as specified and as directed

M&L Concrete bed to drain pipes of size 200 mm dia with using PCC ( 1:3:6) type C2 (using 40 mm graded stone aggregate) with necessary form work including packing under and haunching against the sides of pipes with concrete, after they are laid including testing, complete all as specified and as directed

Cutting into existing manholes for connecting new drains of size 100 mm dia of pipe making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required complete all as specified and as directed.

Cutting into existing manholes for connecting new drains of size 150 mm dia of pipe making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required complete all as specified and as directed.

Cutting into existing manholes for connecting new drains of size 200 mm dia of pipe making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required complete all as specified and as directed.

M & L Point wiring with 1.5 Sq mm copper conductor single core FRLS PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC conduit concealed as per site requirment and conduit accessories of suitable dia medium grade and pressed steel terminal boxes of 2 mm thick MS of suitable size duly painted with red oxide metal primer including fixing/grouting sunken/ surface as per site requirement covered suitable for fixing switches / sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLS PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly for one light/fan/Bell point controlled by one, one way switch 5A, SP complete all as specified and directed. Note: Rate of metal flush box and modular cover plate along with all accessories shall be inclusive of rate quoted by the contractor.

All as per Item No.116 above but one 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per Item No.116 above but one 3 Pin 5 Amps switch socket Independt board.

All as per Item No.116 above but using 2.5 Sq mm FRLS single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 5/15 Amps switch socket combination point including running of 2.5 Sq mm FRLS copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

S & F Modular switch 1 way 6/10 A, 1 Module capacity 230 volts complete all as specified and directed.

S & F Modular switch 1 way 16 A, 1 Module capacity 230 volts complete all as specified and directed.

S&F Socket outlet flush type 3 Pin, 5 amps, 230 volts combined 2 Module complete all as specified and directed.

S&F Socket outlet flush type multipurpose 2/3 Pin, 5/15 amps, 230 volts combined 2 Module complete all as specified and directed.

S & F Ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed.

S&F Sheet metal enclosure MCB DB SPN 8 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified and directed.

S&F MCB, Single Pole Neutral (SPN) 40 Amps, 415 Volts of rupturing capactiy 10 KA, 'C' Series complete all as specified and as directed.

S&F MCB, Single Pole (SP), 6-32 Amps, 240 volts of rupturing capacity 10 KA, 'C' series complete all as specified and as directed.

S & F in replacement of wall mounted batten type LED light of 12 watts with aluminium extruded batten and system lumens of 1200 lm minimum with IP & surge protection alongwith driver efficiency >85% and power factor >0.95 , colour rendering index CRI>80 along with integrated driver complete and connecting to the point wiring with necessary flexible copper conductor of multistrand three core of suitable length from fitting to the ceiling rose complete all as specified and directed. Make: Philips Model BN021 LED12S PSU GR or equivalent model in Havells/Wipro/GE.

S & F in replacement of wall mounted batten type LED light of 22 watts with aluminium extruded batten and system lumens of 2200 lm minimum with IP & surge protection alongwith driver efficiency >85% and power factor >0.95 , colour rendering index CRI>80 along with integrated driver complete and connecting to the point wiring with necessary flexible copper conductor of multistrand three core of suitable length from fitting to the ceiling rose all as directed. Make: Philips Model BN021C LED22S or equivalent model in Havells/Wipro/GE.

S & F in replacement of Security Lights of 25 watt LED light with high power LED and unique peanut lens to ensure uniform distribution with suitable pipe bracket 32 mm dia 0.60 Mtr length fixed on wall with suitable flat iron clamps and nut bolts including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed.

M & L Submain wiring with two runs of single core 6 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through and including rigid PVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of 6 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified. Note:-Three runs of 6 sqmm cable and one run of conduit shall be measured and paid as one unit length.

M&L Earthing complete with galvanised steel earth plate electrode 60cm x60cm x6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth earth lead 4 mm dia, by means of nuts, bolts, check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe light grade 15mm bore from earth elelctrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agagregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25x6mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI pipe light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point made out of Bronze/Gun metal with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, all as per electrical plate No 5 of SSR Part-I and connection to earth test point incl testing on completion complete all as specified and directed. Note :- Item of Earthing includes cost of 7.5m long galvanised iron earth lead 4 mm size and protection pipe of 15 mm bore GI light grade.

S&F Exhaust fan made of sturdy Engineering plastic,250 mm sweep,copper winding,1200 RPM, 230 V, 50 Hz complete with louvers shutter voltage ,complete all as specified and directed.

S&F Exhaust fan made of sturdy Engineering plastic,300 mm sweep,copper winding,1200 RPM, 230 V, 50 Hz complete with louvers shutter voltage ,complete all as specified and directed.

Supplying, laying, jointing, testing and commissioning of LT XLPE insulated, PVC sheathed cable 1100 volts grade of size 4 core,10 sqmm galvanized steel strip or wire armoured, heavy duty, electric cables, with multistranded aluminium conductor laid in trenches/ passing through pipe/duct/road crossing or fixed on poles, walls with suitable size clamps made out of mild steel flat iron including jointing material such as crimping type lugs, brass cable glands, heavy duty double compression type etc. complete all as specified and directed.

Supply and spread sand in trenches for cable cushioning including watering and consolidation all as specified Note : For the purpose of payment punned thickness only will be measured.

Supplying and laying commom burnt clay building bricks sub class B designation 75 of size 230mmx115mmx75 mm complete all as specified and directed.

Supply and lay, galvanized tubing 20 mm bore, medium grade ISI marked, ISI marked including all fittings such as bends elbows , tees, short pieces , connectors,, backnuts, diminishing pieces , caps, plugs, and unions, etc laid in trenches complete all as specified and directed.

Supply and lay, galvanized tubing 25 mm bore, medium grade ISI marked, ISI marked including all fittings such as bends elbows , tees, short pieces , connectors,, backnuts, diminishing pieces , caps, plugs, and unions, etc laid in trenches complete all as specified and directed.

S&F 20 mm dia gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed

S&F 25 mm dia gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed

KR PADMAVATHI CONSTRUCTIONS (BID ID -3353785)

K.S. CONSTRUCTION (BID ID -3349672)

BEEGEE DESIGN SYSTEMS (BID ID -3361858)

J.V.V.K.PRABHAKARARAO (BID ID -3353840)

M/s GM Constructions (BID ID -3362064)

harshraj and co (BID ID -3352304)