REPAIRS AND DAY TO DAY MAINT WORKS TO FLOOR WALL ROOF SANITARY FITTINGS JOINERIES AND CERTAIN OTHER ITEMS IN E AND J AREA AT NAVAL BASE UNDER GE NW KOCHI

Amount

Notes:- 1. Contractor should deploy data entry operator to print the complaint slip from complaint cell daily at 8.30 AM to 5:30 PM with necessary stationary take printout of job cards. 2. All complaints to be rectified in time. The Delay in rectification of complaint more than specified and the following condition not met, the penalty will be levied @ Rs.500.00 Per complaint. (a) Item No 1 to 7, 88 to 100 complaint should be complete in 24 hours (b) all other complaint should be complete in 07 days except major complaints (c) all Major complaint should be completed in 28 days “No complaint should pending more than 28 days” . (d) In case of any urgent / Emergency nature of work plumber/carpenter/mason should available 24 hours all 7 days should available for work and nothing extra shall be admissible on this account. 3. The complaints shall be communicated to the contractor/rep of contractor/ site engineer / site supervisor through Online compliant management portal/website, SMS, Telephonic calls, Letter / Register or other suitable mean of communication at any time. 4. All complaints related to Sanitary fittings / plumbing fittings/ Builders hardware, materials to be purchased as per approved make and kept in store in case of complaint immediately to be attended. 5. The quoted rates includes the scaffolding/staging upto 10 floor height and shaft portion etc. 6. The quoted rates include all the safety equipment's to be used like glouses, safety belts, helmets, mask, safety goggles etc 7. The type of complaint will be decided by Engr-in-Charge. if contractor is not agreeing to the decision of Engr-in-charge the same shall be referred to the Accepting officer whose decision shall be final, binding and conclusive.

M&L for repair to Pillar taps, of any description or size for stopping leakage of water by changing washers, spindle/nut bolt etc complete all as specified and directed by Engineer-in-Charge.

Repairs to low level flushing cistern including changing of syphon, washers, handles, float valves, stopping leakage of Down pipe by applying m-seal, providing flush tank cover if missing and other related works of to make the flushing cistern functional complete all as specified and directed by Engineer-in-Charge.

Repairs to joinerys works, such as removal of door/window shutter with easing/adjusting of door, and refixing with different opening including repairs of wire mesh, cub board shutters, iron mongerys, any type of carpentery works etc properly closing/opening , tightening of hinges or changing the position of hinges, adjustement of tower bolts sliding bolt etc complete all as specified and directed by Engineer-in-Charge.

M&L for repairs to plaster, floor, plinth etc and like using PCC 1:2:4 Type B0 not exc 75mm thick and plaster in CM 1:4 incl roughening and cleaning the surface, applying neat cement slurry as required making good, finished even and smooth without using extra cement in patches of area n.exc 0.50 Sqm in plan and removal of rubbish off the premises complete all as specified and directed.

M&L petty repairs/ refixing of wall tiles, floor tiles, skirting, dado, kota stone , granite stone, RCC Jali, window cill, door jambs, ceiling plaster, fixing of EWC and IWC and neat cement slurry as required making good, finishing even and smooth without using extra cement in patches area n exc 1.00 Sqm each patch plaster, floor, plinth etc and like by PCC 1:2:4 Type B0 n exc 75mm thick and plaster in CM 1:4 incl preparing roungening and cleaning the surface, and removal of rubbish off the premises complete all as specified and as directed.

Petty repair of false ceiling by removing of gypsum board and snap grid and fixing 6mm dia hanger and refixing with repair all damaged wires and snap grid complete all as specified and as directed

Petty repair of steel windows by welding and fixing of hinges, openable/closable condition with oil/greasing etc complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm and removing from site complete all as specified and directed.

All as item above but exc 1.50 Sqm and n.exc 4.00 Sqm each.

Taking down shutters of any descriptionexc 1.00 Sqm and n.exc 2.00 Sqm each and removing from site complete all as specified and directed.

S&F IInd class hardwood plain solid straight chowkhat and frame wrought framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F MS work as in hold fast and similar small articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (Using 20mm graded stone aggregate) as in cills, copings, bed blocks for hold fasts and the like complete all as specified and directed.

S&F, 30mm thick Flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides Make : Century/Action Tesa

M&L 30mm thick IInd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc, edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of members of shutter as specified in SSR (Part-I)- 2009 complete all as specified and directed.

S & F 30mm thick IInd Class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm ivory colour PVC sheet reinforced with M.S. square tube, S&F in opening as per specification and drawing complete all as specified and directed. Make : Rajshree / Sintex

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded ivory colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of ivory colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, and 5mm thick x 15mm wide PVC sheet beadings used inside stiles and rails and decorative PVC beading of 10mm x 10mm used instead of exposed portion of PVC sheet beading and suppling & fixing in the frame at site as per specification & drawing.

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/springs clips complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm each pane complete all as specified and directed.

S&F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 Sqm each pane complete all as specified and directed.

S&F mild steel framed work as in door,chowkat,grills, gratings etc with ends of bars shouldered and riveted or forged into spikes, framed guard bars, barred iron doors etc, conforming to Fe-290, Gde-E-165 all as specified and directed.

S/F 100 mm long mild steel butt hinges medium weight

S/F 75 mm long mild steel butt hinges medium weight

S&F aluminum anodized barrel tower bolt 200mm long of extruded section complete all as specified and directed.

S&F aluminum anodized barrel tower bolt 100mm long of extruded section complete all as specified and directed.

S&F aluminum anodized sliding door bolt 300mm long with hasp and staples (bolt type) and fixing clips of sheet cast of extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F aluminum bow handle "D" type anodized 150mm long complete all as specified and directed.

S&F aluminum bow handle "D" type anodized 100mm long complete all as specified and directed.

S & F in repair stainless steel 4 lever Mortice lock,vertical type, size 100 mm

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Ditto all as per item No. 31 but fixed in repair.

S & F two legged aluminium floor door stopper with rubber shoe 140mm long complerte all as specified and directed by Engineer-in-Charge.

S&F in repair MS helical door spring 300mm long including roller and roller plate complete all as specified and directed.

Repair to rolling shutter of any size and including greasing, oiling complete all as specified and directed.

Repairs to Aluminum door shutter / windows of any size including taking down and cleaning / repairing / replacement of all fittings and fixtures (If required) and re-fixing in the same opening complete all as specified and directed at site by Engineer-in-Charge.

S&F in repair drapery rod 30mm dia Aluminum fancy type powder coated wood finish including rings, knobs and brackets complete all as specified and directed.

S&F in repair Aluminium extreded section Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixedcomplete all as specified and directed.

S/F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainlesss , steel ocver, governing picot made of brass other parts made of mild steel heavy duty in repairs.

S&F in repairs, 16-18mm MDF DWR Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including beading /matching laminates to exposed edges f of board complete all as specified and directed.

S&F in repair 30mm width of flaps Continous (Piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F in repair for 40mm dia cupboard knobs fixed with nut, screws and washer of wooden finish brass polished complete all as specified and directed.

S&F in repair magnet catcher to wooden frame work complete all as specified and directed.

S &F in repair stainless steel selfclosing type hinges for kitchen cabinet of approved quality all as specified and directed.

S & F ball bearing for rolling shutters

S&F Aluminum powder coated fixed type windows including suitable nylon beading channel gasket etc complete with following specification :- Frame :- 60mmx40mmx1.80mm Panel :- 4mm thick ACP sheet / 5mm thick tinted/frosted glass of approved colour and design

S&F aluminum powder coated door shutter with frames of size - 40x45x1.8 mm incl. screwing of frame glass necessary joints cleats, glazing clips rubber packing, snap beading, suitable handle, tower bolt, SS butt hinges,mortice lock 4 lever with 65 mm latch size including aluminium anodized door frame of size 60x 40 x1.8 mm thick fixed to wall with necessary screws and plug complete all as specified & directed. (rates for one no hydraulic door closer per shutter & 5 mm thick tinted glass /4mm thick ACP sheet reqd to be fitted in shutters is included in the item )

S&F aluminum powder coated parttion fixed/sliding type with frames of size -side , top rail and intermidiate sections size 85x44.45x1.5 mm , incl. screwing of frame glass necessary joints cleats, glazing clips rubber packing, snap beading, fixed to wall with necessary screws and plug complete all as specified & directed. (rates for4.80 mm thick tinted glass / 4mm thick coloured aluminium composite panels reqd to be fitted in shutters is included in the item )

S & F 4mm thick coloured/wooden grain aluminium composite panel (approved by Engr-in-Charge) cladding to PVC rainwater pipe/RCC column etc and including aluminium framing complete all as specified and directed

M&L for preparation of new surfaces of wood and wood based materials of any descriptions not otherwise described over 10Cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any descriptions not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed.

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

M&L for precast cement concrete block masonry in type B1, 1:3:6 (20 mm graded aggregate) with solid blocks exc 10 cm in width and setting in cement mortar 1:6 in foundation load bearing wall and wall complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded crushed stone aggregate) as in plinth protection /hardstanding , laid in panels, finished the top surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L RCC (1:2:4) type B-1 (Using 20mm graded crushed stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja/facia projection and the like complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any light Shade (square/rectangular) area of each tiles exc 0.42 Sqm but not exc1Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:4 laying floor finishes, complete all as specified and directed by Engr-in-Charge. Note :Quoted rate shall be inclusive of Screed bed

M&L Vitrified coloured tiles 8-10mm thick Light shade (square/rectangular) area of each tiles exc 0.36 Sqm but not exc 0.90 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 to recieve tiles complete all as specified and directed by Engr-in-Charge. Note :Quoted rate shall be inclusive of backing coat

M&L for joint free Non-skid ceramic coloured tiles 7-8mm thick (square/rectangular), area of each tile not exc 0.11 Sqm, over and including 15mm thick screed bed in CM (1:4) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge. Note :Quoted rate shall be inclusive of Screed bed

M&L for Glazed ceramic coloured joint free tiles 450x300X7mm in vertical surfaces over and including 10mm thick rendering in Cement mortar (1:3), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge Note :Quoted rate shall be inclusive of backing coat

M&L Vitrified coloured tiles 10mm thick light shade (Square/Rectangular) area of each tiles n.exc 0.36 sqm, over and including 15mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge Note :Quoted rate shall be inclusive of Screed bed

M&L Vitrified coloured tiles 10mm thick light shade (Square/Rectangular) area of each tiles n.exc 0.36 sqm, as in skirting/dado, over and including 10mm thick rendering in Cement mortar (1:3) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge Note :Quoted rate shall be inclusive of backing coat

M&L for Machine cut pre polished Kota stone slab 18-20mm thick as in floor/ treads of steps (single piece) laid over and including 15mm thick screed in CM 1:4, set & jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of the slab including cutting, rubbing complete all as specified and directed by Engr-in-Charge. Note :Quoted rate shall be inclusive of Screed bed

M&L for machine cut pre polished Kota stone slab 18-20 mm thick (single piece) as in risers to steps, skiting/dado, pillars, window cills and the like, laid over and including 10mm thick rendering in cement mortar 1:3, set & jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed by Engr-in-Charge. Note :Quoted rate shall be inclusive of backing coat

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) stone slab as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 15mm thick in CM (1:4) complete all as specified and directed by Engr-in-Charge. Note :Quoted rate shall be inclusive of Screed bed

M& L for grinding of existing terrazo or kota stone flooring by carborundum stone of 320 to 400 grit size. After grinding the surface shall be washed clean and grouted with neat cement grout of cream like consistency using the same coloured cement as in the original mix. After grinding the surface shall again be washed clean and rubbed hard with felt and slightly moistened oxalic acid powder, at the rate of 5 gm of oxalic acid powder for one sq m of floor surface. After completion of grinding work the wax-polish shall be sparingly applied with soft linen on the clean and dry surface. Then the polishing machine fitted with bobs shall be run over it. Clean saw-dust shall then be spread over the floor and polishing machine again applied, mopping up surplus wax and leaving glossy surface. Care shall be taken that the floor is not let slippery.

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed

M&L 15mm thick rendering cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge. (WPC shall be paid seperately)

M&L 5mm thick rendering in ceiling of cement mortar (1:3) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

Supply only liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

M&L for three coats of white wash to newly plastered surfaces of ceiling including preparation of surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for two coats of oil bound distemper over a coat of 1.5mm thick wall putty to newly plastered surface including preparation of surfaces complete all as specified and directed

M&L two coats of cement based paint over a coat of primer to newly plastered surfaces of wall including preparation surfaces complete all as specified and directed

S&F in repair 110mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed

S&F in repair 75mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed

S&F in repair PVC (SWR) bend any radius 110mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore complete all as specified and directed by Engr-in-Charge.

S & F 200mm dia of half round or 180 mm width rectangular PVC SWR ready made eaves gutter of pressure rating 6 Kg/cm2 of approved make including necessary fitting like bend WC/MS Clips etc complete all as specified.

S&F in repair vitreous china squatting pan ‘Orissa pattern’ size 580x440mm white with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe, etc and including lime concrete bedding complete all as specified and directed.

S&F in repair PVC flushing cistern low level 8 to 10 Ltr capacity of approved make including fixing of brackets connection to WC with CI brackets and making good disturbed area complete all as specified and directed.

S&F in repair vitreous china WHB white with flat back of size 550x400mm with bracket including waste coupling and PVC waste pipe complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern white including fixing with trap including PVC matching seat cover complete all as specified and directed.

S&F in repair 100mm dia SS grating with or without hole for waste pipe complete all as specified and directed.

S&F in repair brass CP towel Rail 600mm long "D" type complete all as specified and directed.

S&F in repair vitreous china soap dish fixed to wall with screw complete all as specified and directed.

S&F in repair 15mm bore Pillar taps, in repair cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S & F in repair Vitreous China urinals, half stall type complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with PTMT Urinal spreader, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S & F in repair vitreous china table top WHB,, size 640 x 400 x 120mm excluding taps, waste, chain and plug and procelin stopper complete all as specified and directed

S & F in repair vitreous china wash down water closet pan single piece (pedestal pattern) size 365 x 655 x 760mm UF soft close seat cover fixing accessaries set and accessaries set cistern fittings and S trap 220mm complete all as specified and directed

S & F plastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complerte all as specified and directed

Dismantling wrought iron or mild steel work of any description complete all as specified

M & L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

M & L Welded steel wire fabric weight n exc 4 kg/sqm fixed to steel members complete all as specified

Dismantling single layer Mangalore pattern or similar tiles in roofing.

Dismantling plain or corrugated steel sheeting any gauge, thickness complete in roofing.

Dismantling battens for tiles, shingles, etc of any size exceeding 15cm spacing including tilting fillets.

Dismantling timber boarding any description fixed in any position with nails.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/blankets, any thickness including cover fillets.

Dismantling timber scantiling 40 Sqcm and over in section unframed work in any position.

M&L for IInd class hard wood boarding clean sawn with butt joints, 20mm thick as in soffits of gutter, eves board fixed with nails, etc.

S&F 0.63mm thick glavanised corrugated mild steel sheeting with two corrugation side lap fixed with 'L' type or 'J' type hook bolts and washers in roofs with grade of zinc coating 275

S&F Plain Aluminium sheeting 0.71mm thick, Alloy 31000H4 in ridge, hips, valley gutter, drip and straight flashings.

S&F for pre-painted galvalume zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F for pre-painted galvalume zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

M&L for Mangalore pattern roof tiles interlocking at side joints laid dry.

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles bedded and jointed in CM 1:6.

M&L for 2nd class hard wood in scantling clean sawn fixed as in purlins, rafters, etc in roof.

M&L for 2nd class hard wood clean sawn battern for tile at 30cm centres of sectional area exc 15Sqcm and n.exc 25Sqcm.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240.

M&L for preparing and treating tiles battens any size and spacing with one coat of creosote complete all as specified. (Measured overall in one side only spacers not deducted)

S/F Aluminum snap grid false ceiling with grid 605x605mm size including hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40 x 3 mm size 60 mm long & expansion hold fastners 12.5 mm dia 40 mm long complete all as specified

S/F 4mm thick Non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium framework with stainless steel screws complete all as specified

M&L for repairing of conceald flushing cistern by replacing existing float valve and discharge valve including minor adjustments and servicing of Make - Cera/perryware/Jaquar etc

LAKSHMI BUILDERS (BID ID -3069371)

M/s T.P SHAJI (BID ID -3071875)

S&C ENTERPRISES (BID ID -3072011)

M/s ANTONY THOMAS AND CO (BID ID -3071537)

ANIE JOHN CONTRACTORS (BID ID -3068635)