UPKEEP AND MAINTENANCE OF WATER SUPPLY INSTALLATION UNDER GE UTILITY AMBALA CANTT

Amount

Taking out the pumpset and transportation for repairing motor pump set to workshop, taking out burnt winding wire from submersible motor of capacity 50 HP/40HP 3 phase, rewinding with suitable size of PVC coated copper winding wire including replacement of burnts bushes complete including all insulation material and transportation back to site and fixing the same, testing and commissiong complete all as specified and directed by Engineer in charge. Note: (i) Any fault such as short circuit, earth fault, burning of submersible cable due to unbalance load or any other reason occur in the motor after repair during the currency of contract shall be bear by the contractor and rates are deemed to be included in the item for rectification of the fault. (ii) Spares for replacement shall be measured and paid separately under respective items as supply only.

Supply only in replacement of bearing bush for submersible motor of capacity 40 HP to 50 HP complete all as specified and directed by Engineer in charge.

All as per srl item No. 02 here in before but rotor sleeve for submersible motor.

All as per srl item No.02 here-in before but thrust bearing for submersible motor.

All as per srl item No.02 here-in before but thrust plate for submersible motor.

All as per srl item No. 02 here-in before but motor coupling with key for submersible motor.

All as per srl item No.2 here-in before but water drain plug for submersible motor.

All as per srl item No.2 here-in before but upper bearing housing assembly for submersible motor.

Material and labour in replacement of rotor for submersible motor of capacity 40 HP to 50 HP complete all as specified and directed by Engineer in charge.

Material and labour in replacement of stator for submersible motor of capacity 40 HP to 50 HP complete set with all connected items all as specified and directed by Engineer in charge.

Material and labour in replacement fully automatic star-delta starter for submersible pump set of capacity 50 HP , 415 V , with relay range 45-75 amps with single phase preventer 50 Hz 3 Phase complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in cement mortar incl all quoins, arches, pillars, in any situation etc complete all as specified and directed by Engr-in-Charge.

Material and labour brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for attending any type LT panels/Internal lights/Starters complaint at various water supply installations and rectify the same, rates are also included for replcement of thimbles any type and any size with nut-bolts and cable jointing with tap, gland packing, greasing in pumps/valves with all connected items all as specified by the Engr-in-Charge. Note: Complaint should be rectified within 06 Hrs otherwise a penalty of Rs 250/- per day will be imposed.

Dismantling and taking down rusted old UNSV LT Panel inner/outer outer covers and M&L for Outer covers of LT panel board of existing size , outer shell made out of 3.1 mm thick for uouter panel and MS sheet with front openable and back bolt openable lockable, followed mm for inner panels by powder coated painting having thickness not less than 100 microns complete all as specified and directed by Engr-in-charge

Supplying, laying, jointing and testing in replacement of existing size with pre-insulated multi standard copper conductor flat of size 25 sqmm, 3 core submersible cable and connected with suitable and required thimbles and nut bolts to panels. Make: Finolex/Havells/Polycab/Grandlay/RR Kabel

S & F in replacement for preparation of chart of water supply distribution system of various installation (drawing line plan/layout information will be provided by the dept for preparation of drawing) complete all as specified and directed.

Material & Labour for brick masonry valve pit of internal size 120cm x 120cm x 120cm with one brick thick wall using sub class ‘B’ brick in cement mortar 1:6 over 20cm thick PCC plate form with 15cm off sets on every side of 1:3:6 type C-1 including plastering of internal surfaces and exposed surfaces with 15mm thick plastering in cement mortar 1:4 and 50mm thick RCC cover in two equal parts 1:2:4 type B-1 with 10mm dia deformed bars at 10cm center to center on both side including necessary form work with 150mm dia hole in the center complete including demollition and removing of old material from the site for credit or disposal all as specified and directed by Engineer-in-Charge.

Taking down wooden chowkats or frames area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed.

Taking down wooden chowkats or frames area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and as directed.

S&F factory made Box type steel window, single shutter, glazed and with side hung shutters including box type hinges, steel handles (size 150mm) fabricated type for each leaf duly welded, mild steel barrel tower bolts 200mm size (02 Nos for each leaf) duly welded, complete with glazing bars dovetailed or welded including MS fillets, including provision of mild steel guard bars complete all as specified and directed. Note- provided with sliding MS door bolts of size 250mm, handles 02 Nos size 150mm if required shall be provided by contractor on no cost basis.

Material and Labour for plain cement concrete 1:2:4 type B-1 (using 20 mm graded mechanically crushed stone aggregate) as in fixing of hold fasts, copings, bed plates,kerbs or mud stops, lintels upto 1.50m span, plinth courses , seismic and other bands and the like, finished the surface fair and even, including necessary form work complete all as specified and directed. Note- If reinforced concrete, reinforcement shall be measured and paid for separately.

Supply and fixed ,Plain framed, panelled shutter size 35mm(two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr in charge. Note :- provided with sliding MS door bolts of size 250mm , handles 02 Nos size 150mm , tower bolt two nos size 200mm if required shall be provided by contractor as no cost basis.

Supply and fixing mild steel works in bands, straps, supports, stays, bolts, hooks, hold fasts etc, similar articles conforming to Fe-290.Gde-E-165, complete all as specified and directed.

Hacking out old broken glasses area n. exc 1.5 sqm, any thickness and in any position from wooden or metal frames fixed with oil putty or beads etc and removing from site, complete all as specified.

Supply and fixed for sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified.

M&L for preparation of old decorated surfaces of walls chajjas balcony facia etc and applying two coat of exterior emulsion paint complete all as specified.

M & L for preparing old painted steel surfaces/pipes of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of existing colour as per site required complete all as speciied and directed.

M & L for preparing new painted steel surfaces/pipes of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of existing colour with red oxide primer as per site existing complete all as speciied and directed.

M & L for preparing old painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of existing colour with pink primer as per site existing complete all as speciied and directed.

M & L for preparing new painted wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of existing colour with pink primer as per site existing complete all as speciied and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level complete all as specified and directed by Engr-IN-Charge,

Material and labour for vibratory compacted, precast cement concrete rubber moulded, interlocking designer paver blocks , confirming to IS-15658-2006 of 60mm thickness, M-35 grade, as in path, hard standing, etc. laid over and including 25mm compacted sand cushioning ,including 75mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate , complete all as specified and directed by Engr-IN-Charge,

Dismantling of floor or wall tiling/ kota stone/ dholpur stone/chequered tile /ceramic tile including cement mortar bedding and removing the rubbish outside the defence land complete all as specified and directed .

Supply & fixing in replacement heavy duty rubber moulded coloured chequered tiles with laquer polish for extra shine of 50 Sqm size 300 mm x 300 mm x 22-25 mm thick, ISI marked, set, jointed and pointed in neat cement slurry over and including 20 mm thick (average thickness) cement screed (1:4) base complete all as specified and as directed.

supply and fix in repair/ replacement for premium quality, joint free non skid coloured ceramic tiles, 300 x 300 x 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) base, complete all as specified.

supply and fix in repair/ replacement for Premium quality, glazed coloured ceramic tiles 600 x 300 x 7mm thick on vertical faces including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified.

Supply and fixing in repair 5 Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including 10mm thick backing coat of plaster in cement motar 1:3 (one number SS clamps ) (grade -202) of flat 30mm X 2mm,150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment.

Supply and fixing in repair for machine cut kota stone slab 20-25 mm thick (of size not less than (55 cm x 55 cm) laid in floor, jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 15mm thick in cement mortar (1:4) base , complete all as specified.

Cutting/removing of bushes/small trees/vegetation growth upto a distance of appx 50 mtr around the UG sump,OHT,Pump house not exc 30cms deep incl drains all around the plant incl rough surface leveling/cutting,filling upto 12" height/ depth all around the plant and burning at a distance of 50mtr (minimum) in the presence of Engr-in-charge including sprinkling the round up chemicals for drying/killing the bushes,shrubs etc.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion & making good disturbed ground embedded in Concrete, brick work, masonry, etc.for fixing of new fencing post complete all as specified and directed by Engr-In-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 Cum in any type of soil, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering, & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil all as specified.

Material and Labour mild steel angle iron 60 x60x 6mm, cut to length, bent to shape required including cranking, bending spirally for hooping columns, hooking ends and binding with welding for securing chain link fencing etc conforming to Fe-290.Gde-E-165, complete all as specified and directed.

Material and Labour PCC in foundations, filling and mass-concrete type B2 (1:2:4) using 40 mm graded crushed stone aggregate complete all as specified.

Material and Labour MS FLAT 50 X 5mm for securing of chain link fencing and similar small articles etc confirming to IS-15911 all as specified and directed.

Supply and Fixing MS screw bolts 5 to 10mm dia (machine made) with hexagonal or square head at one end, screwed end to be fitted with washer and one hexagonal/square nuts and 5 to 10 cm long all as specified and directed.

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provission of binding wire all as directed.

Supply only chain link MS galvanisd fencing, any size or type all as specified and directed. (Wt of chain link fencing shall be calculated by BOO at site)

Cutting V groove 10 mm wide and 30mm deep in concrete floor and filled polyurethane joint sealant complete all as directed.

M&L in repair for Mild steel framed works such as grills, gratings etc with ends of bars, shouldered and/or rivetted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame works of water tank and similar work confirming to Fe.290.Gde-E-165 including nuts, bolts, washers, welding, binding, cold or hot, drilling holes for bolts, in any shape or size inclusive of one primer coat, one under coat and one finishing coat of paint as specified and directed by Engr-in-charge.

Material and labour dewatering as well as cleaning of under ground sump/ reservoir internally from base to top including scraping the mud, silt from the base and walls, washing the complete internal surfaces with clean water removing the silt/mud outside the surrounding area and desilting / removal of mud from the connecting pipes cleaning the mouths of the internal pipes and depositing the same n. exc 100m away from site of capacity 10 lakhs gallon complete all as specified and directed by Eng-in-Charge.

All as per srl item No 46 here in before but of capacity 1.0 Lakh gallon.

M&L for Mild steel, plain, black sheet of thickness upto 3 mm in wall cladding, steel gates/tank and sump covers and similar work, cut to size, holes punched; incl round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints whith rivetted or welded seams, incl bending or turning up, mitred angles etc and one coat of primer and one coat of paint after fixing as required all as specified and directed by EIC.

M&L for making the UG sumps/ any other kind of surface, crack proof by providing & applying damp-proof waterproofing coating system with two component water base Epoxy chemical Dr Fixit Dampguard Classic. 1. SURFACE PREPARATION: Thoroughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc. All large voids or hollow portions must be removed and re-plastered. Non-moving cracks having width upto 5 mm must be filled with Polymer based crack filler. 2. APPLICATION: Apply the first coat of Dr Fixit Dampguard Classic with a paintbrush directly on the prepared surfaces by mixing (1 part base:1 part hardner: 1 part of water) . Allow to dry for a minimum 2-3 hrs. Apply one part of DAMPGUARD mixed chemical and 2 parts of OPC white cement and make the Putty, apply Putty on the entire surface area. Allow it to dry for at least 3-4 hours. Apply the Final coat of Dr Fixit Dampguard Classic on the entire surface.

M&L scraping the existing paint by using wire brushes and sand paper etc and preparing the external surface and applying two coats of cement base paint on UG sump complete all as directed by Engineer-in-Charge.

Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on surface of any description of brick or concrete and finished the surface even and smooth without using extra cement complete all as specified.

Material and labour for 15mm thick rough cast plaster over and including 10mm thick base rendering in cement mortar (1:4) on brick or concrete surface of any description with WPC @2% by weight of cement or as per manufacturer’s instructions, finished even and fair, complete all as specified. (Note : WPC shall be measured and paid separately)

Supply only integral water proofing compound, complete all as specified.

Dismanteling the UNSV sign board in installations . Supply and fixing retro reflector board of size 4'x3' with high quality retro reflector tape blue base high intensity prismatic sheeting (HIP) grade white retro tape cutting good quality with 3mm thick ACP sheet base including 40mm x 40mm square size MS pipe legs and all around the board appx 18 feet incl welding the MS flat plate of size 25mm x 3mm across the board appx 10 feet including grouting the sign board in PCC 1:2:4 complete all as specified and directed by engr-in-charge. Note: Details/description of printing words will be provided by department.

Supply and fixing in replacement high quality ACP sheet board at installations of size 5 feet x 3 feet minimum with router cutting letter blue base of sheets and white colour acrylic letter with complete fitting of minimim 3 Nos LED lights of 20W of 4 feet complete all as specified and directed by engr-in-charge. Note: Details/description of printing words will be provided by department.

S&F Electric Resistance Insulated Rubber Floor mat sheet of size 1mx2mx25mm thick ISI marked and equivalent colour as per direction with fixing mtrls complete all as specified and as directed.

Supply and fixing in replacement of concerteena coil with barbed wires and barbs having 1000mm dia of streched coils complete all as specified and directed by Engr-IN-Charge,

Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof covering, complete all as specified.

Supply and fixing pre-painted galvatume aluminium zinc coating GI based corrugated mild steel sheeting 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding and fixed with self tapping screws, complete all as specified.

Material & Labour for PVC water storage tank 500 Litre capacity HDPE triple layer ISI marked fixed & hoisted in position on staging or roof complete with locking arrangement, over flow pipe, air lock pipe, Ball valves, high pressure of PTMT with, ISI marked complete all as specified. including dismantling of old tanks of of any description complete all as specified.

Disconnecting all electrical connections from electric motor 60 HP installed at sec 'C' and decoupling from pump assembly and dismantling from foundation and transporting to local workshop approved by Accepting Officer for opening the motor taking out of burnt winding and thorough cleaning of the slotes, rewinding the complete motor with supper enamaled copper wire of same size and provn of supper quality insulating materials, warnishing, replacing the bearing sets and cooling fans if required and drying and taking back from wksp including laths and other any type of machine work such as rotor work, welding, metalling, machining and grinding for bearing sheet etc and mounting, connecting all electrical connections alongwith reassembling pump set and testing complete all as directed by Engr-in-Charge. NOTE: Rewinding amount of motor will be paid to the contractor once only irrespective of how many number of times motor rewinded .

All as per item no. 61 here in before but 50 HP motor and ditto-

All as per item no. 61 here in before but 40 HP motor and ditto-

All as per item no. 61 here in before but 30 HP motor and ditto-

All as per item no. 61 here in before but 25 HP motor and ditto-

All as per item no. 61 here in before but 12.5 /10/ 7.5/5HP motor and ditto-

Decoupling of centrifugal pump from electric motor, dismantling from the foundation and shifting to local workshop approved by Accpeting Officer for opening the pumps for checking and rectification of defects by welding/threading/cutting/replacing defective parts which shall be measured and paid separately as supply only herein after including transporting back and refixing and testing complete for Model No : DSM 125/40 Make: Kirloskar all as specified and directed.

All as per item No. 62 here in before but for Model No : DB 125/26 Make: Kirloskar

All as per item No.62 here in before but for Model No : UP 80/38 Make: Kirloskar or Raw water turbine pump

All as per item No. 62 here in before but for Model No : SCT 80/38 Make: Kirloskar

All as per item No. 62 here in before but for Model No : SP4LA Make: Kirloskar

All as per item No. 62 here in before but for Model No : 4/5 2STGMEDIMKI Make: Mather Platt/Vacuum Centrifugal Pump

Supply & fixing in replacement electronic motor protection relay fully protection from over current, under current, Phase loss, Phase reverse, Auto/manual reset input 1A to 5A through CT adjustable Trip complete suitable for upto 120 HP motor starter all as specified and directed.

Supply & fixing of rubber coupling TC-13, TC-14, TC-19, TC-22 and as per existing required for centrifugal pump sets complete as specified and directed by Engr-in-Charge.

Supply and fixing of metal coupling for centrifugal pump sets complete suitable for existing pump sets as specified and directed by Engr-in-Charge.

Repairing the LT control starter panel/AMF panel of the centrifugal pump and motor by disconnecting the cable, removing u/s parts of the panel, wiring and replacement of u/s wiring and parts under respective items including cleaning by vacuum cleaner, thimble, testing the panels on load complete as specified and as directed by Engr-in-Charge.

Supply, fixing and replacement of Power contactor 3 pole MNX 25 or MC10DN, series A1, AC3,40A, for 25HP/30HP AC rating 40 Amp, 220 V complete suitable for existing starter all as specified .

Supply, fixing and replacement Power contactor 3 pole, MNX A1-A2, 30 KW and 40 KW AC rating upto 80 Amp, 220 V complete suitable for existing starter all as specified

Supply, fixing and replacement Power contactor 3 pole, MNX 70, 45 KW AC rating upto 80 Amp, 220 V complete suitable for existing starter all as specified

Supply, fixing and replacement Power contactor 3 pole, BCH MCE15M, series A1, 75 HP AC rating upto 100 Amp, 220 V complete suitable for existing starter all as specified.

Supply, fixing and replacement Power contactor 3 pole, BCH MCE15M series A1, AC3,110A 120 HP AC rating upto 150 Amp, 220 V complete suitable for existing starter all as specified.

Replacement of the unserviceable timer switch type ST 100 suitable for 240 Volts with mounting kit of capacity 3-30Sec, 50 Hz complete as as specified.

Supply, fixing and replacement of Single phase preventor/Phase sequence corrector for upto 120 HP motor or AC rating upto 160 Amp, 415 VAC, 50 Hz (VSP2) complete suitable for existing starters all as specified. Make : BCH, Indo-Asian, Siemens, Minilec

Supply and fixing MCCB TPN 36KA breaking capacity 500Amp, 415 V adjustable type complete all as specified and directed.

All as per Sl item No 74 here in before but 320 Amp and ditto----

All as per Sl item No 74 here in before but 250 Amp and ditto----

All as per Sl item No 74 here in before but 200 Amp and ditto----

All as per Sl item No 74 here in before but 160 Amp and ditto----

All as per Sl item No 74 here in before but 125 Amp and ditto----

All as per Sl item No 74 here in before but 100 Amp and ditto----

Supply and fix in replacement ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 630 Amps complete all as specified and directed. Make havells or equivalent as per existing.

All as per item No 75 here in before but of 320 Amps.

All as per item No 75 here in before but of 200 Amps.

All as per item No 75 here in before but of 160 Amps.

Supply and fix in replacment defective aluminium bus bar(set of four) of rating upto 400 Amps including nut , bolts, washers, etc complete all as specified and directed.

Supply and fix in replacement defective phase indicators (set of three red, green & yellow) of ratings 240 volts, single phase complete all as specified and directed.

Supply and fix in replacement of DOL starter for motor pump set upto 5HP all as specified and directed by Engr- In- charge

Note:- Amount of credit of Rs 277465.00 for retrieved materials is mentioned in Schedule of Credit attached in tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s badrinath Traders