Establishment of CETP at Silk Tech Park Zakura

Earth work in bulk excavation by mech means (hydraulic excavator) over areas (Exceeding 30cm in depth 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth lead up to 50m and lift up to 1.5m. in all kinds of soil.

Providing and laying of boulder filling /stone layer under foundation concrete

Providing and laying cement concrete of specified grade including curing but excluding the cost of centring and shuttering, finishing and reinforcement all work up to plinth level – 1:3:6(1 cemnt:3 coarse sand: 6 graded stone aggregate 20mm nominal size) - M10

M-30 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve work ability without impairing strength and durability as per direction of Engineer-incharge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Cantering & shuttering including strutting and propping etc. And removal of forms for RCC work desired height in foundation, foundation beams, plinth beams, lintel beams, all types of suspended floors, soffits of beams ribs, stepped, spiral staircases etc up to desired heights and thickness complete.

Providing and fixing of precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer –in –Charge) 0.50mm+/-5% total coated thickness (TCT), Zinc coating 120gsm as per IS:277 in 240 Mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyester topcoat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self-drilling/self-tapping screws of size (5.5x 55mm) with EPDM seal ,complete up to any pitch in horizontal /vertical or curved surfaces ,excluding the cost of purlins ,rafters and trusses and including cutting of size and shape wherever required.

Providing and laying in position 100/150 mm G.I line Intake line to main sewage sump 15m (150mm bore) From intake sump to screen chambers including back flow line 100mm bore 20m From screen chamber to MBBR 100mm bore 11.0m From MBBR-11 to tube settler 100mm bore 6.0mx2 = 12m Tube settler to slice chamber 100mm bore 13m Sluice chamber to sludge holding tank 6.0m Share holding tank to centrifuge 15.0m From centrifuge to exit 6.0m a.150mm bore 15m@ Rs 750/m = Rs 11250

b. 100mm bore 83m @ Rs 820/m = Rs 68060

Providing and fixing the pipe specials a. 100mm bore N/R valves 2no @ Rs 27500

b. 100mm bore B.F.V valves 07 nos @ Rs15500

c.150mm sluice valves 1no @ Rs 27500

Providing and fixing in position with all required accessions Pressure sand fitter with 20 H/P motor/Pump 1.5 dia @ Rs55000

Providing and fixing 500lit cap triple layer pre tank hypo chlorine including all fittings Viz @ Rs 6700

20mm bore heavy gauge pipe feeding line from C.W.tank with 2HP. Pump motor assembly@ Rs 15000

One no agitator with all fittings and 1.5HP motor Rs 6500

Feeding lines in 20mm bore heavy gauge line for pre and post chlorination as per drawing (attached)

Providing and fixing in position one number 3mm dia H/s tank,3 deep painted with 3 coats of epoxy paint both internally and externally for use as A/C/C tank and filled with sandlayers of A?C upto 1.20mm depth including all materials like F.M/F.S/A/C and all pipe complete job tested and commissioned.@ Rs 35000

Providing and fixing in position one number 3mm dia H/s tank,3 deep painted with 3 coats of epoxy paint both internally and externally for use as A/C/C tank and filled with sandlayers of A?C upto 1.20mm depth including all materials like F.M/F.S/A/C and all pipe complete job tested and commissioned.@ Rs 35000

Air blowing system Providing and fixing complete air blowing system for 2 number MBBR Sludge holding tank Main sludge sump The item includes 2 number air blowers One operational One stand bye MGF/ACF OIL Skimmer Air release line Air blowing screens for all the above tanks The item also includes all the lines/fillings/valves as are necessary Complete texted and commissioned Primary pump(sludge pump) 2 Nos @

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Course bar screen ISMB-200

Providing and fixing of electric panel with 3 phase meter with all required accessorises

Providing and installation of 02HP motor with all necessary accessories complete job

Maintenance for two years

Supply and fixing of online monitoring system (complete job)

Provision for getting consent to establishment/operate from pollution control boards(JKPCB)