Construction of New Kumar Chhatralaya (S.T.) at Netramali, Taluka-Idar, Dist. Sabarkantha

Name of work :- Construction of New Kumar Chhatralaya

(S.T.) at Netramali, Taluka-Idar, Dist.

Bill of Quantities

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

1 Excavation for foundation upto 1.5 m depth including sorting 1355.0 Cum 157.08

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

2 Excavation for foundation for depth from 1.5 m to 3.0 m 584.00 Cum 287.47

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(C) Hard

3 Filling available excavated earth (excluding rock) in trenches. 2099.00 Cum 136.92

plinth, sides of foundations etc. in layers not exceeding

cm. in depth consolidating each disposited layer by ramming

4 Filling in plinth with sand under floors including watering 98.00 Cum 481.81

ramming, consolidating and dressing complete

5 Filling in foundation and plinth with murrum or selected soil 492.00 Cum 294.39

in layers of 20cm. thickness including watering, ramming and

consolidating etc. complete.

6 Providing and laying controlled cement concrete M.150 for 282.00 Cum 4201.60

curing complete including cost of formwork but excluding the

cost of reinforcement for reinforced concrete work in (A)

Foundations, footings,Base of columns and Mass concrete

7 Providing and laying controlled cement concrete M.250 and 319.00 Cum 4519.75

curing complete including cost of formwork but excluding the

cost of reinforcement for reinforced concrete work in (A)

Foundations, footings, Base of columns and Mass concrete.

8 Providing and laying controlled cement concrete M250 and 28.00 Cum 6952.84

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Columns, pillars posts and struts Column Up to

9 Providing and laying cement concrete 1:4:8 (1- Cement : 4- 24.00 Cum 3374.11

coarse sand : 8- Machine Crushed stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

10 Providing and laying controlled cement concrete M.250 and 73.00 Cum 6002.43

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work for Ground and Plinth Beams

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

11 Brick work using common burnt clay building bricks having 120.00 Cum 4214.33

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

12 Providing and laying controlled cement concrete M.200 and 105.00 Cum 7864.32

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Columns, Pillars posts and struts, For All Floors.

13 Providing and laying controlled cement concrete M.200 and 24.00 Cum 8001.67

curing complete including the cost of formwork (Vertical

fins and vertical sun breakers.) and reinforcement for

reinforced concrete work in (B) Walls, for all floor level

14 Providing and laying controlled cement concrete M.200 and 216.00 Cum 6136.23

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Beams For All Floors.

15 Providing and laying controlled cement concrete M.200 and 390.60 Cum 6441.40

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Slab for All Floors.

16 Providing and laying controlled cement concrete M.200 and 36.00 Cum 6454.21

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Lintels For All Floors.

17 Providing and laying controlled cement concrete M.200 and 11.00 Cum 6989.40

curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in Chajja For All Floors.

18 Providing and laying controlled cement concrete M.200 and 22.00 Cum 6905.88

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (E) Staircases

19 Providing TMT Bar FE 500D reinforcement for R.C.C. work 159773.00 Kg. 77.29

including bending, binding and placing in position complete

20 Providing throating or plaster drip and moulding to R.C.C. 218.00 Rmt 43.08

Chhajja by making 5mm to 15mm wide grove as per design

21 Brick work using Common Burnt Clay building bricks having 613.00 Cum 4529.55

crushing strength not less than 35 kg./Sq.Cm. in Super

structure Above plinth level up to All Floor levels in Cement

Mortar 1:6 (1- Cement : 6 -fine sand) (Conventional)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

22 Half brick masonry in common burnt clay building bricks 612.00 Sqmt 691.76

having crushing strength not less than 35 Kg/Sq.Cm. in

Superstructure above plinth level upto All Floor level in

Cement mortar 1:4 (1- Cement : 4 -coarse sand )

(Conventional).

23 Providing & Fixing Chicken mesh for joint between brick 346.00 Sqmt 173.72

work & RCC work fixing with nail & GI washer as per

director in charge

24 Providing 15mm thick cement mala plaster in single coat on 4724.00 Sqmt 269.68

Rough (Similar)side of single or half brick walls for interior

plastering and finished even and smooth fininshing with a

floating coat of neat cement slurry in (i) Cement mortar 1:3 (1-

cement:3-sand), 10x10 mm groves etc. Complete for All

25 Providing 10mm thick cement mala plaster in single coat on 3666.00 Sqmt 241.32

brick/concrete walls for interior plastering and finished even

and smooth fininshing with a floating coat of neat cement

slurry in (i)Cement mortar 1:3 (1-cement:3-sand). Complete

for All Floors.

26 20mm thick sand faced cement plaster with Gutka Finish on 1908.00 Sqmt 321.10

walls upto height 15 metres above ground level consisting of

12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and

8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand)

with 5mm grooves, etc. complete.

27 Providing Water Proofing Treatment on Sunk Slab including 183.00 Sqmt 370.67

cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-

graded stone aggregate 20mm nominal size) laid in one layer

and finished with a floating coat of neat cement average

50mm thick to prepare slope including water proofing

chemical etc. Complete for Sunk Slab for All Floor.

28 Applying two coats of putty & two coats of primer of 7872.00 Sqmt 40.59

approved brand and manufacture on new wall surface to give

an even shade including thoroughly brushing the surface free

from mortar dropping and other foreign matter and sand

papered smooth.

29 Wall painting (three coats) with plastic emulsion paint of 4260.00 Sqmt 125.52

approved brand and manufacture on undecorated wall surface

to give an even shade including throughly brushing the

surface free from mortar droppings and other foreign matter

and sand papered smooth.

30 Ceiling painting (three coats) with plastic emulsion paint of 3659.00 Sqmt 131.02

approved brand and manufacture on ceiling and soffits of slab

surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

31 Finishing wall with weather proof exterior emulsion paint 2316.00 Sqmt 93.93

(two coats) with Damp Proof Coating (one coat) on wall

surface to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose

powdered materials.etc complete

32 Providing and laying polished Kota stone slab flooring over 1587.00 Sqmt 1019.00

20mm (Average) thick base of cement mortar 1:6 (1-cement :

6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand)

laid over and jointed with grey cement slurry mixed with

pigment to match the shade of slab including rubbing and

polishing etc. complete. (A) 25mm thick

33 Providing and laying polished kota stone slab 25mm thick in 105.00 Sqmt 1166.93

risers of steps,skirting Dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed

with gray cement slury mixed with pigment to match the

shade of slab including rubbing and polishing etc. complete.

34 Providing and fixing pre-cast Rubber Dye / steel Dye inter 1180.00 Sqmt 706.93

locking concrete block 60mm thick with grade of concrete

M300 pnumatic compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the joint

with sand in proper line and level as per guidlines of IRC : SP

63-2018 etc. Complete.

35 Providing and fixing Machine cut & Polished kota stone in 50.00 Sqmt 1355.42

7.5 cm width Strip flooring for Ramp even grade over 20mm

(Average) thick base of cement mortar 1:6 (1-cement : 6-

coarse sand) laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25mm thick

36 P & L 24" x 24" Ceramic 10 mm thick tile flooring over 20 246.00 Sqmt 1266.54

mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing flooring by

adhesive material including dismentaling of existing flooring

and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete for

37 Providing and laying coloured glazed tiles of the size 300 mm 1196.00 Sqmt 1487.88

x 450 mm x 8 mm in skirting, risers of steps and dedo on

mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) &

jointed with white cement slurry.

38 Providing and laying Ceramic tiles 6mm thick in skrting 14.00 Sqmt 1090.32

risers of steps and dedo on 10mm thick cement plaster 1:3 (1-

cement : 3-coarse sand) and jointed with white cement slurry

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

39 Providing and fixing Machine cut, Free edges, Mirror 93.00 Sqmt 2464.40

Polished Granite stone slab flooring 18mm thick laid on

20mm (Average) thick base of cement mortar 1:6 (1-cement :

6-coarse sand) for Trade & Riser including Half Round

moulding front edge of trade jointed with grey cement slurry

mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete.

40 Providing and fixing Machine cut, Free edges, Polished 438.00 Sqmt 2510.86

Green Granite stone slab flooring 18mm thick for vertical

wall/Doors/Windows Sill, Jams for cladding as per design

including full moulded round inside edge and laid on10mm

thick base of cement mortar 1:3 (1-cement : 3-coarse sand)

jointed with grey cement slurry mixed with pigment to match

the shade of slab including rubbing and polishing etc.

41 Providing and laying water prooofing treatment with china 728.00 Sqmt 1132.21

mosaic tiles flooring over avg 50 mm C.C. 1:2:4 bedding

maintaining slope for plain and curve surface & 12 mm to

mm broken pieces not more than 2.5 cm of ceramic/ of glazed

tiles to be laid over cement mortar 1:3 to plain or slope and to

be tempered to bring mortar creme out upto surface using

white cement including rounding off junctions and extending

them upto 15 cm along the wall,clearing with water and

oxalic acid etc. as directed.

42 Constructing Sandwich Platform of 18mm thick polished 50.00 Sqmt 2760.33

black or selected granite at top and 25 mm thick kota stone

with 75cm height with necessary support using 20mm thick

cement mortar 1:3 for sandwich and fitting at bottom & edges

with waterproof rigid adhesive including making necessary

grooves in walls with vertical support of double kota stonr

sandwich every 60cm centre to centre including all labour

material of approved quality including full moulded round

front edge fixed in wall for partition.

43 Providing and fixing flush door with Single shutters, solid 155.00 Sqmt 4129.89

core construction with frame of first class hardwood with

cross board and finished with 1 mm thick laminate on both

side of shutter, machine glued PVC beading on periphery

including 30cm long Stainless Steel Pipe handle on both side

SS ASIS 304 grade, SS Stopper 20cm, SS Aldrop 30cm both

side, anodised alluminium butt hinges with necessary screws.

(B) Non-decorative type and block board core anodised

alluminium butt hinges in flush door shutters (2) 35 mm

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

44 Providing and fixing flush door with Double shutters, solid 12.00 Sqmt 5279.27

core construction with frame of first class hardwood with

cross board and finished with 1 mm thick laminate on both

side of shutter, machine glued PVC beading on periphery,

including 30cm long Stainless Steel Pipe handle on both side

SS ASIS 304 grade, heavy duty Floor Spring each side, SS

Stopper 20cm, SS Aldrop 30cm both side, anodised

alluminium butt hinges with necessary screws. (B) Non-

decorative type and block board core anodised alluminium

butt hinges in flush door shutters (2) 35 mm thick.

45 Providing and fixing window having extruded aluminum 144.00 Sqmt 1738.21

Colour anodized section frame main outer size 95mm x

24mm x 1.17mm @ wt.of 0.738 Kg/mt , horizontal Three

track member size 92mm x 31.75mm x 1.30mm,@ Wt.1.07

Kg/mt , vertical member of size 92mm x 31.75mm x 1.50mm

@ Wt. 1.06 Kg/mt with sliding shutters of horizontal member

size 40 mmx18mm x1.29mm @ wt.of 0.456 Kg/mt, vertical

member of size 40mm x 18mm x 1.29 mm @ wt.of

0.456Kg/mt/ with 5 mm thick transparent bronze colour

tinted float glass with rubber gasket and airlock strip

anodiazed aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc. With

Mosquito net shutter in outer track.

46 Providing and fixing standared extruded of alluminium 16.00 Sqmt 2131.10

section of size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094Kg /

Rmt with colour anodized alluminium frame with 5 mm thick

transparent bronze colour tinted float glass as details etc

complete for Fix window with Mosquito net.

47 Providing and fixing Louvers in G.I Channel 40x32x5mm 101.00 Sqmt 2215.94

size And 114mm Wide G.I Sheet Having Thickness of

0.55mm & Weight Not Less Than 490 Gm/Mtr. Roll Formed

to create 84mm wide Louver snap fixed on special shaped G.I

Channel,Channel shall be Finished with Powder Coating of

55 micron For Fix Louvers As Directed By Engineer In

48 SIGNAGES ON DOOR :Providing and fixing 304 grade 42.00 Nos. 1262.50

stainless steel 1.5mm thick brushed steel finish plate fixed on

a door using S.S studs and with punched (laser cut) lettering

carried out on S.S plate of required size and text as directed

by engineer etc. complete. Size 30 cm x 15 cm

49 Providing erecting and fixing double coated ISI water tank of 20000.00 Litre 3.95

required capacity each with all necessary fittings and

connection etc. complete on terrace

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

50 Providing, laying and jointing in true line and level 110 472.00 Rmt 876.11

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring, &

fittings conforming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using

of PVC clamp of the size 110 mm diametre x 149 mm length

x 145 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings

such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all

51 Providing, laying and jointing in true line and level 160 408.00 Rmt 834.38

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring, &

fittings conforming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using

of PVC clamp of the size 160 mm diametre x 210 mm length

x 196 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings

such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all

52 Providing laying and jointing in true line and level 50mm dia. 86.00 Rmt 195.67

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

53 Providing laying and jointing in true line and level 25mm dia. 655.00 Rmt 91.84

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

54 Providing laying and jointing in true line and level 15mm dia. 350.00 Rmt 72.65

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

55 Providing and fixing concealed center point to wall ceiling & 105.00 Rmt 253.82

floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making good

the wall, ceiling and floor etc. complete. 25 mm.

56 Providing and fixing concealed center point to wall ceiling & 150.00 Rmt 170.36

floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making good

the wall, ceiling and floor etc. complete. 15 mm.

57 Providing and fixing Gun metal check or non-return fullway 17.00 Nos. 420.63

wheel valve.(C) 25mm dia.

58 Providing and fixing ball cock of approved. quality as 2.00 Nos. 189.84

directed.(A) Copper Metal (ii) 50mm dia.

59 Providing and fixing C.P. brass shower rose with 15mm or 40.00 Nos. 282.16

20mm inlet.(A) 100mm dia. Each

60 Providing and fixing wash down water closet (Wall Hung 23.00 Nos. 5172.51

type, W.C. Pan) with integral P or S trap, Health Fauset

Heavy Duty with hook and PVC dual flush tank with

complete fittings including jointing the trap with soil pipe in

Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover

to be measured and paid for separately)(A) vitreous China

Pattern :(i) in white colour

61 Providing and fixing washbasin (ii) Flat Back washbasin 550 15.00 Nos. 2180.72

mm x v 400mm size. (i) In white colour including with

approved sanitary grade material with CP waste coupling,

waste pipe, 15mm dia Pillar & Stop Cock of approved brand

with connection 15mm dia flexiable pvc pipe etc. complete

62 Providing and fixing Kitchen sink with C.I. or M.S. brackets, 2.00 Nos. 2987.87

painted white including cutting holes in walls (C) Vitreous

China Sink.(i) 600mm x 450mm x 150mm size including

approved sanitary grade material with CP waste coupling,

waste pipe, 15mm dia Pillar & Stop Cock of approved brand

with connection 15mm dia flexiable pvc pipe etc. complete

63 Providing and fixing screw down bib taps of following 85.00 Nos. 186.83

size.(A) Brass screw down bib tap polished bright. (i) 15mm

64 Providing and fixing PVC SWR Nahni trap IS 14735 for 51.00 Nos. 586.60

drain - 100 mm diameter with jali of the following nominal

diameter of self cleansing design with C.I scread down or

hinged grating including the cost of cutting and making good

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

65 Providing and fixing S.W. gully trap with C.I. grating brick 40.00 Nos. 1246.92

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps.(B) 150mm x 100mm size P or R type

66 Providing and fixing C.P. brass towel rail comlete with C.P. 29.00 Nos. 616.42

brass brackets fixed to wooden plugs with C.P. brass

scews.(B) 600mm x 20mm size.

67 Providing and fixing 600mm x 450mm bevelled edge mirror 12.00 Nos. 859.41

of superior glass mounted on 6mm thick A.C. sheet or

plywood sheet and fixing to wooden pluge with C.P. brass

screws and washers.

68 Providing and fixing in position PVC cowel went to pipes 12.00 Nos. 75.75

69 Constructing brick masonry chamber for underground C.I. 20.00 Nos. 3660.76

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe

with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete

etc. complete.(ii) Inside dimensions 500mm x 700 mm and

450mm deep for pipe line with one or two inlets.

70 Providing and laying (to level or slopes) and jointing with 6.00 Rmt 531.18

stiff mixture of Cement Mortar in proportion 1:1 Salt glazed

stoneware pipes including testing of pipes and joints complete

and Providing and laying Cement concrete 1:5:10 (1-Cement

: 5-Fine sand :10-Graded stone aggregate 40mm nominal

size) bedding for stoneware pipes of following internal

diameters with necessary formwork and curing complete.(B)

71 Providing and laying (to level or slopes) and jointing with 6.00 Rmt 352.73

stiff mixture of Cement Mortar in proportion 1:1 Salt glazed

stoneware pipes including testing of pipes and joints complete

and Providing and laying Cement concrete 1:5:10 (1-Cement

: 5-Fine sand :10-Graded stone aggregate 40mm nominal

size) bedding for stoneware pipes of following internal

diameters with necessary formwork and curing complete.(A)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

72 Applying general insecticide pest control treatment to floors, 819.00 Sqmt 80.62

cupboards etc including labour materials etc. complete. Using

Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075%

concentration by mass) is recommended 10.5ml chemical

diluted with 5 liters of water application 0.5 litre chemical

/Sqm of surface is recommended as per I.S.

73 Providing and fixing Safety Grills of required pattern for 4765.00 Kg 110.60

windows/door using MS polished bars, Rectangular CRS

Pipes of size 50mm x 30mm x 2mm or Required at required

spacing as per design and hold fast with coach bolts including

one coat of and two coats of matt finished oil painting etc.

74 Providing and fixing a set of wall mounted 38mm dia. U 1.00 Nos. 2323.00

shaped horizontal stainless steel collapsible grab bar, 38mm

vertical stainless steel fixed grab rail of grade SS 304 from

round pipe supported and 75mm dia 8mm thick SS 304 base

flange on wall including anchor fastners, nuts, accessories as

per detailed drawing etc. complete as directed by architect or

engineer in charge.

75 Providing and fixing of conspectus tape 50mm width on of 160.00 Rmt 1923.04

treads in staircase including cutting pasting etc. As per

harmonised guidelines complete in all respect to the entire

satisfaction of engineer in charge.

76 Providing and fixing 90 cm high Stainless Steel railing made 91.00 Rmt 3760.33

from anticorrosive 304 grade S.S. pipe of 50 mm dia. (16

gauge) as hand rail with S.S.304 grade baluster of 32 mm dia

(16 gauge) as a vertical support fixed in RCC Slab/ steps of

stair at 1.2 mt. c/c including three horizontal S.S. pipes of

mm dia (16 gauge) at equal distance fixed by 16 mm dia (16

gauge) S.S. pipe with baluster including accessories as per

detailed drawing as directwed etc. complete

77 Providing and Fixing 8mm thick poly- Carbonate fiber sheet 14.00 Sqmt 2940.82

using sealant water proofing rubberished adhesive oil painted

50x50mm hollow channel for framing of shade as require and

fixing frame with surrounding wall etc. completed as

78 Steel work, welded in built up sections framed work 114.00 Quintal 9108.48

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

79 Painting two coats (excluding priming coat) on external 131.00 Sqmt 22.75

surface of new rain water, soil, waste and vent pipes and

fittings with ready mixed bituminous brushing, black,

anticorrosive to give an even shade including cleaning of all

dirt, dust and other foreign matter. (B) 75mm dia.

80 Excavation for foundation upto 1.5 m depth including sorting 192.00 Cum 268.21

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(C) Hard Murrum

81 Providing, laying, spreading and compacting stone aggregates 94.00 Cum 1820.79

of specific sizes to water bound macadam (Grade-II) (B.T.

Metal of size 45 to 63 mm) specification including spreading

in uniform thickness, hand packing, rolling with 3 wheeled

steel/ vibratory roller in stages to proper grade and camber,

applying and brooming requisite type of screening/ binding

Materials to fill up the interstices of coarse aggregate,

watering and compacting to the required density.

82 Providing and Casting in situ controlled Cement Concrete M- 600.00 Cum 4553.38

200 for R.C.C. Raft and cutt-off walls including necessary

shuttering laying, vibrating, ramming and curing complete.

83 Clearing and grubbing road land including uprooting rank 1.00 Hectare 28455.10

vegetation grass bushes, shrubs, sapling and trees girth up to

300 mm removal of stumps of trees cut earlier and disposal of

unserviceable materials (C) By mechanical means in area of

84 Earthwork in cutting including preparing the slope and 18.00 Cum 500.05

camber and stacking or utilising the cutting stuff in bank as

directed upto 200 Meters from the end of cutting with all lead

and lift.(i) Hard murrum.

85 Providing and laying controlled cement concrete M.150 and 13.00 Cum 7426.53

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work for Coping

86 Providing & laying weep hole in Aburtments, and returns by 380.00 Each 86.73

using A.C. pipe of 100mm including laying in proper grede

and jointing the completed as per detailed specification.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

87 Providing and fixing concertina coil fencing with punched 190.00 Rmt. 565.60

tape concertina coil 600 mm dia 10 mt openable length

having 50 no rounds per 6 mt length, upto 3mt height of wall

with existing angle iron (50mm x50mm x5mm )requird

shaped As per Directed Engeenier in charge. placed 2.4mt or

3.00mt apart and with 4 horizontal R.B.T. reinforced barbed

wire(3 mm) , stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or G.I.barbed wire tied

to angle iron, all complete as per direction of Engineer-in-

charge, with reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at compound wall for

ESR M4/intakewell.

88 Steel work, welded in built up sections framed work 24.00 Quintal 9108.49

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

89 Drilling of pilot bore hole of size 250/300 mm diameter at 250.00 Rmt 1544.29

above site by mud finish direct rotary rig etc. complete

90 Reaming of 250/300 mm diameter pilot bore hole to size 450 200.00 Rmt 742.35

mm diameter including assembling, lowering housing, casing

strainer pipes with gravel packing and clay ball packing etc.

91 Providing 600 CFM / 150 PSI capacity air compressor upto 1.00 Job 25118.70

available of sand free discharge ( Minimum 6.0 Hours)

92 Supply of reducer made frim 6 mm thick plate (M.S.) for 1.00 Nos. 2009.90

ERW pipe of size (ii) 200 mm dia. x 250 mm dia. X 600 mm

93 Supply of 200 mm diameter V-wire screen pipe of slot size 65.00 Rmt 1401.88

1.0 mm nominal hole etc. complete.

94 Supply of M.S. Bore clamps with 3 holes on either side with 1.00 Pair 1753.36

nuts and bolts of standard make and suitable size (g) 750 mm

x 75 mm x 16 mm flat to 200 mm dia. Pipe.

95 Supply of Bore Plug having 100 mm height made from M.S. 1.00 Nos. 834.26

plate with 3 holes at equal distance on circumference for nuts-

bolts type, locking arrangement with nut-bolts & lock nuts of

standard make complete. (b) from 5 mm thick M.S. plate (for

top also) (ii) suitable for 200 mm dia. pipe.

96 Supply of M.S. Bail Plug having length of 0.45 mtr from 1.00 Nos. 907.99

medium class pipe as per I.S.S. suitable for (b) 200 mm

diameter pipe etc. complete.

97 Supply of Steel Bent plates suitable to ERW pipe for (b) 200 8.00 Nos. 71.71

mm diameter and 150 x 150 x 6 mm size etc. complete.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

98 Supply of Gravel of size selected size up to 4mm to 6 mm, 12.00 Cmt 2295.73

including stacking and filing etc. complete.

99 Charges for uptron make Electrologger (with carting ) of pilot 1.00 Job 12120.00

bore hole etc. complete.

100 Charges for Geo Hydrological ground water investigation 5.00 Job 16160.00

including water sample chemical analysis etc. complete.

101 S.I.T.C. submersible pump set suitable for bore of 150 mm 1.00 Each 49148.62

dia or more having 3 phase motor capacity not less than

HP with following capacity. Lifting and Lowering taken

extra. [C] 25 stage 160 to 100 LPM discharge at 185 to

mtr head for 50 mm dia delivery pipe

102 Providing and erecting PVC corrugated Flexible conduit with 1116.00 Rmt 26.26

required numbers of coupling, PVC bushes, Check-nuts etc.

complete of following sizes. (3) 32 mm diameter

103 Lowering of submersible motor pump set complete with 1.00 Job 2568.43

required. Nos. and size of casing pipes erected by means of

proper chain pulley block & pipe wrenches after checking of

threads of each pipe with coupling to take the load of the

pump set and pipe assembly filled up with water. (B) Above

60 mtr and up to 120 mtr

104 Supplying and erecting approved make motor control cubical 1.00 Each 8710.24

panel (Direct - on - line) made from 16 G. CRCA sheet duly

epoxy powder painted inside and outside with hinged doors

and locking, arrangement consisting of suitable size of ON-

OFF isolator (AC - 3/23 duty) main fuses, single phasing

preventer, indicating lamps for R-Y-B phases, overload relay,

automatic water level controller, Ammeter, Voltmeter each

with two way selector switch incoming, wires duly socket

crimped, main contactor & overload relay, start-stop push

buttons, to be erected on angle iron frame grouted on wall as

directed. The isolator, overload relay & contactors will be of

L&T, Seimens or BCH make only (a) DOL upto 7.50 H.P.

105 Supplying and erecting XLPE (IS:7098) (I)-88 ISI 200.00 Rmt 136.35

unarmoured copper cable 1.1 KV grade to be erected as

directed of following size. (E) 3 core 2.5 Sq. mm

106 Providing laying and jointing in true line and level 50mm dia. 150.00 Rmt 195.67

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

107 Providing and fixing butterfly valve of IS approved brand (D) 2.00 Nos. 1595.80

108 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 1.00 Nos 958.17

size having weight not less than 35Kg.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

109 Earthwork for embankment including breaking clods, 4287.00 Cum 131.93

dressing with all lead and lift (including watering and

consolidation)(A) From Borrow pits within land width

110 Rolling and consolidation of soling including filling in 3251.00 Sqmt. 22.75

depression which occur during the process, with power roler

8 tonne to 12 tonne..

111 Box cutting the road surface to proper slope and camber for 325.00 Cum 109.05

making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto 50Mt.lead.

112 Construction of B.I.T.C. granular sub base by providing 130.00 Cum 1380.96

granular material of Grading II, spreading in uniform layers

with motor grader on prepared surface , mixing by mix in

place method with front end loader at OMC , and compacting

with vibratory roller to achieve the desired density ,complete

113 Compaction and finishing of cement concrete road by trimix 563.00 Sqmt. 72.72

process providing extra labour charges for the trimix vaccum

dewatering service process on cement concrete road surface

by using vaccum dewatering pump floater surface vibrator

including making rough finish to surface as per in including

levelling the complete.

114 Supplying and fixing reinforced concrete heavy duty non- 40.00 Rmt. 660.00

pressure pipes with collars for culverts carrying heavy traffic

as per IS 458-1991 specifications including setting the pipes

in C.M. 1:2 watering and laying (to level or slopes) of class

NP3 of following internal daimeters.(i) 300mm dia.

115 Construction of Cattle trap made from ISMC 100 border and 8.00 Sqmt. 6146.86

G.I. pipe 50 mm dia. Heavy duty at 12cm spacing by welding

and for supports 2 nos. I.S.M.C. 100x75x6 section fixing in

prepared chamber as per drawing.

116 Constructing Brick masonry road gully chamber 500mm x 16.00 Nos. 2017.20

450mm x 600mm including 500mm x 450mm C.I. horizontal

grating wih frame complete.

117 Supplying of yellow or Goradu soil with all lead and lift 283.00 Cum 505.00

including spreading watering dressing and rolling with hand

roller etc complete selected soil

118 Supplying of well rotted FYM manure with all lead and lift 15.00 Cum 378.75

including spreading mixing dressing and rolling with hand

roller etc. complete

119 Supplying and planting Dibbling semi carpet lawn at distance 326.00 Sqmt. 90.90

of about 15 cm x 15 cm after proper anti termite treatment

and rolling the same by hand roller and watering etc complete

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

120 Bowling and developing flowering plants grown in nursery 30.00 Nos. 505.00

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Bottom Palm

121 Bowling and developing flowering plants grown in nursery 30.00 Nos. 656.50

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Triangle Palm

122 Bowling and developing flowering plants grown in nursery 35.00 Nos. 80.80

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Jasud

123 Bowling and developing flowering plants grown in nursery 30.00 Nos. 85.85

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Croton

124 Bowling and developing flowering plants grown in nursery 40.00 Nos. 85.85

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Croton

125 Bowling and developing flowering plants grown in nursery 50.00 Nos. 70.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Croton Petra

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

126 Bowling and developing flowering plants grown in nursery 30.00 Nos. 40.40

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Croton Petra Live Plant

127 Bowling and developing flowering plants grown in nursery 40.00 Nos. 101.00

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Golden Durenta Varigated

128 Bowling and developing flowering plants grown in nursery 35.00 Nos. 85.85

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Crotons Variety

129 Bowling and developing flowering plants grown in nursery 500.00 Nos. 35.35

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Green Mahindi

130 Bowling and developing flowering plants grown in nursery 25.00 Nos. 85.85

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Varigated Ficus

131 Bowling and developing flowering plants grown in nursery 30.00 Nos. 70.70

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted New Black Ficus

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

132 Bowling and developing flowering plants grown in nursery 500.00 Nos. 45.45

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted White Ribbon Plants

133 Bowling and developing flowering plants grown in nursery 500.00 Nos. 60.60

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Green Mahendi border

134 Bowling and developing flowering plants grown in nursery 30.00 Nos. 95.95

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Pendulla Asopalav

135 Bowling and developing flowering plants grown in nursery 30.00 Nos. 121.20

having approximate height 4 to 5 t or Height as per

Landscape Plan with natural growth and natural colour

planted in a lump of soil packed in polyethylene bag or

earthen pot including organic & chemical fertilizer pesticides,

fungicides, hormones & maintaining the plants up to three

months as Deserted Potted Plants

136 Labour charges for planting various plantsafler proper anti- 1935.00 Nos. 70.70

termite treatment in pits including placing properly and filling

the pits with required prepared mix soil and watering and

dispporting etc. complete

137 Maintance of the garden for 60 days after Complition of 3 1.00 Job 25250.00

month stipulated period is completed for plantation of lawn

and plants including applying second round of proper anti-

termite treatment

138 Rubber Hose Pipe 15 mm dia of approved brand and make 75.00 Rmt 90.90

139 Providing and fixing G.I. Nipple as directed 10.00 Nos. 50.50

140 Providing laying and jointing in true line and level 40mm dia. 120.00 Rmt 148.12

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

141 Providing and fixing brass screw down stop tap.(A) 15mm 3.00 Nos. 205.83

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

142 Providing & Laying Rain Water Junction Chamber of Clear 10.00 Nos. 6241.80

Internal Size 0.60 x 0.60 x 0.75m with excavation of size

1.36 x 1.36m & 0.15m thick M200 Bed Concrete Including

brick masonary 0.23 thick wall in C.M. 1:6 of 0.75m height

with 15mm thick Cement Plaster inside & outside (1:4),

x 1.06 RCC M200 top slab of thickness 0.15m with TMT

steel and 455mm x 610mm cast iron manhole cover with

frame weight not less than 35 kg as per directed by Engineer-

143 Providing & Laying Filter chamber of brickwork 0.23 thick in 10.00 Nos. 22067.49

C.M. 1:6 of clear internal size 2.04m x 1.20m x 1.20m and

excavation dimension of 2.80m x 1.96m x 1.35m including

C.C. M200 Bed Concrete 0.15m thick and RCC M200 Top

slab of thickness 0.15m with TMT steel, Including 15mm

(1:4) thick cement plaster inside & outside with Cement

slurry & top cover with frame of minimum weight of 35kg,

including filling filter material of 200mm thick each layer of

25-40mm, 10-20mm of BT metal and sand as per directed by

engineer-in-charge

144 Providing & Laying Water Harvesting Pit of clear size 2.00 1.00 Nos. 32558.36

mt x 2.00 mt x 4.00 mt. For water logging with excavation in

any strata upto four meter depth, Brick work 0.23 thick in

C.M. 1:6 of clear internal size 2.00m x 2.00m x 1.20m with

15mm thick C.M. 1:4 plaster, filling the pit with B.T. metal

40mm in 0.60 mt. depth with 25-40mm kaptchi, 0.30 mt.

depth and 2mt. depth with coarse sand in layers including

makng P.V.C. line for water inlet etc. as directed with 250mm

dia bore 15mt. depth amd 150mm dia PVC pipe of

Kg.f/cm2 casing wih gravel packing or as directed.

145 A Pump Room. Supply & fixing Diesel engine driven min. 1.00 Nos. 555500.00

pump of 55 mt. head and 137 M3/ Hr. capacity with

RPM diesel engine with battery charger. Base plate, AVM

pad etc. complete as directed including necessary concrete

platform as directed. (Make:-L)

146 Fire Pumps & Accessories, Yard Hydrant, Internal Hydrant, 1.00 Nos. 153924.00

Hose Reel & Sprinkler System Supply, Installation, Testing &

Commisioning of Main Fire Pump Of Capacity 20 H.P. with

55 mtr. Head, Pump

147 Supply, Installation, Testing & Commisioning of control 1.00 Nos. 90900.00

Panel suitable for automatic operation of fire fighting pumps

consisting (a) Necessary cabling, wiring, earthing from panel

to individual equipment shall be included in the quoted price.

(b) Facility for more selection i.e. auto or manual. (c)

Protection failure and control cabling. (d) Interlocking of

pressure switch with pumps.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

148 Supply, Installation, Testing & Commisioning of 150mm dia. 1.00 Nos. 3535.00

Pressure Gauge of range 0 - 15 kg/cm3 confirming to as per

specification complete as required.

149 Supply, Installation, Testing & Commisioning of Pressure 1.00 Nos. 4545.00

Switches for automation of fire pumps, Pressure switches

shall be double pole, single throw type suitable for 3 phase

supply with diaphragm. Alluminium Enclosure with IP

protection as required.

150 Supply, Installation, Testing & Commisioning of the 40.00 meter 2390.67

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.A)150 mm dia

151 Supply, Installation, Testing & Commisioning of the 45.00 meter 1711.95

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.b)100 mm dia

152 Supply, Installation, Testing & Commisioning of the 10.00 meter 1277.65

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.c)80 mm dia

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

153 Supply, Installation, Testing & Commisioning of the 50.00 meter 1100.90

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.d)65 mm dia

154 Supply, Installation, Testing & Commisioning of the 45.00 meter 989.80

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.e)50 mm dia

155 Supply, Installation, Testing & Commisioning of the 40.00 meter 858.50

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.f)32 mm dia

156 Supply, Installation, Testing & Commisioning of the 150.00 meter 555.50

following sizes of flanges jointed / screwed / welded, M.S.

Pipes of Class C ISI marked including accessories such as

MS bracket, U clamps with Anchor Fasteners, tees / elbows /

reducers / couplings / unions / bends / flanges etc. and laying

on the surface including painting with two coats of

anticorrosive primer and two coats of approved red enamel

paint after laying and testing after installation etc. as per

specifications complete as required.g)25 mm dia

157 Supply, Installation, Testing & Commisioning of C.I. 1.00 Nos. 9738.42

Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets

complete as required. A)150 mm dia

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

158 Supply, Installation, Testing & Commisioning of C.I. 2.00 Nos. 8932.44

Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets

complete as required. b)100 mm dia

159 Supply, Installation, Testing & Commisioning of C.I. 2.00 Nos. 5555.00

Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets

complete as required. c)50 mm dia

160 Supply, Installation, Testing & Commisioning of Cast iron 1.00 Nos. 9090.00

Dual plate Check valve (PN 1.6) a)150 mm dia

161 Supply, Installation, Testing & Commisioning of Cast iron 2.00 Nos. 7564.90

Dual plate Check valve (PN 1.6) a)100 mm dia

162 Supply, Installation, Testing & Commisioning S.S. Single 3.00 Nos. 5656.00

Headed Fire Hydrant Valve with 80mm N.B. Flanged inlet,

63 mm dia. Female instantaneous outlet type S.S. coupling,

blank cap, chain, twist release type lug & all accessories

Confirming to IS:5290. Including fixing with supports,

flanged tapping from wet riser, orifice plate.

163 Supply, Installation, Testing & Commisioning of Weather 2.00 Nos. 4595.50

proof standard M.S. Fire Hose Cabinet wall mounting type

(450mm x 450mm x 250mm deep) having single or double

opening with necessary locking arrangement by allan key

suitable for housing 1 nos. hose pipe, 1 nos. Branch pipe &

nozzle spanner.

164 Supply, Installation, Testing & Commisioning non 2.00 Nos. 5641.86

percolating rubber reinforced lined Fire Hose pipe (as per

IS:636) of 63mm dia and 15 mtr. Long. The hose shall be

rated for burst pressure pf 35.7kg/sqcm. Hose shall be

complete with ISI marked SS male & female coupling

(IS:903) bound & riveted to hose pipe with copper rivets &

1.5mm copper wire.

165 Supply, Installation, Testing & Commisioning of 63mm dia. 2.00 Nos. 5641.86

Instantaneous pattern SS 304, short branch pipe, 20mm dia

nozzle confirming to IS

166 Supply, Installation, Testing & Commisioning of First Aid 2.00 Nos. 6565.00

Hose Reel equipment conforming to 15:884 comprising of

hose reel drum, 8 mm shut off noz:z.le, Ru bber hose of

mm dia x 30 mtr. long, painting, swinging type fixing

bracket, anchor fastener, bolts & nuts etc.

167 Supply, Installation, Testing & Commisioning of SS Ball 2.00 Nos. 858.50

Valve. A) 25mm dia.

168 Supply, Installation, Testing & Commisioning of Cast Iron 2 1.00 Nos. 8585.00

Way Fire Brigade Inlet as per 1S: 904 having 63 mm dia in/et

with blank cap and chain with necessary fit ti ngs, flanges, nut

bolts etc. complete as required. (For Hydrant Network)

169 Supply, Installation, Testing & Commisioning of Gun Metal 1.00 Nos. 959.50

Air Release Valve with necessary fittings. Size: 25mm (For

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

170 Supply, Installation, Testing & Commisioning of Quartzoid 30.00 Nos. 454.50

Bulb type Sprinkler Heads. A) Pendent Sprinkler 57°C

171 Fire Alarm System Alarm panel Microprocessor based 8 zone 1.00 Nos. 16665.00

172 Manual Call Point 3.00 Nos. 454.50

173 2 core x 1.5 sqmm wire with pvc conduct and required 250.00 Rmt. 166.65

174 Smoke Detector 30.00 Nos. 1565.50

175 II) Fire Extinguisher and Exit Signages Supply, installlation, 10.00 Nos. 6447.84

testing and commissioning of Carbon Dioxide (CO2) type

Fire Extinguisher of 4.5 kg confirm to IS:15683, with ISI

marked / TAC approved fitted with required accessories

including wall suspension brakets.

176 Supply, Installation, Testing & Commisioning of ABC type 10.00 Nos. 2222.00

6kg confirm IS:15683, with ISI marked / TAC approved fitted

with required accessories including wall suspension brackets.

177 Signage Boards 25.00 Nos. 252.50

178 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm 7.00 Sqmt 1311.18

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing flooring by

adhesive material including dismentaling of existing flooring

and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete for light

179 Providing and fixing window having extruded aluminum 4.00 Sqmt 1713.70

Colour anodized section frame main outer size 63.50 x

x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track

member size 61.85 mm x 31.75 mm x 1.20mm @ wt.of

0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x

1.30 mm @ wt.of 0.659 Kg/mt with sliding shutters of

horizontal member size 40mm x 18mm x 1.29mm @ wt.of

0.456Kg/mt, vertical member of size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with

mm thick transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc

complete for window.

180 Excavation for foundation upto 1.5 m depth including 40.00 Cum 272.57

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

181 Excavation for foundation for depth from 1.5 m to 3.0 m 14.00 Cum 498.93

including sorting out and stacking of useful materials and

disposing of the excavated stuff upto 50 Meter

lead.(C) Hard Murrum

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

182 Providing and laying cement concrete 1:5:10 (1- Cement : 5- 3.00 Cum 2566.77

fine sand : 10- graded brick bat aggregates 40mm nominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

183 Half brick masonry in common brunt clay building bricks 15.00 Sqmt. 618.79

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:5 (1- Cement : 5 -coarse sand ) in

foundation and plinth (B) Conventional

184 Providing and laying cement concrete flooring 1:2:4 (1- 20.00 Sqmt. 352.01

cement : 2-coarse sand : 4-graded stone aggregate 20mm

nominal size) laid in one layer and finished with a floating

coat of neat cement. (B) 50mm thick.

185 Providing 15mm thick cement plaster in single coat on Rough 88.00 Sqmt. 184.78

(Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and smooth

in (i) Cement mortar 1:3 (1-cement:3-sand)

186 Providing and Laying ordinary cement concrete 1:2:4 (1- 4.00 Cum 6888.15

Cement 2- coarse sand : 4- graded stone aggregates 20 mm

nominal size) and finishing smooth with curing etc. complete

including the cost of formwork but excluding the cost of

reinforsement for R.C.C work in (iii) Slabs having more than

10 cm and upto 13 cm. thickness

187 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 4.00 Nos 958.17

size having weight not less than 35Kg.

188 Providing and laying (to level or slopes) and jointing with 10.00 Rmt 317.48

stiff mixture of Cement Mortar in proportion 1:1 Salt glazed

stoneware pipes including testing of pipes and joints

complete.(B) 150mm dia.

189 Providing, laying and jointing in true line and level 110 234.00 Rmt 876.12

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring, &

fittings conforming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using

of PVC clamp of the size 110 mm diametre x 149 mm length

x 145 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings

such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all

190 Providing and Constructing sock pit of 2.46 mt. dia outside 2.00 Nos 35192.44

and 4 mt depth with honey combed masonary 6.50 mt. from

bottom and 0.60 mt. brick masonary in C.M. 1:6 top with

RCC slab cover of M200 vent pipe 1.8mt. Long 75mm dia &

C.I. cover and cowel vent etc. comp

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

191 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire 399.00 Pts 485.81

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr

length , in below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with

textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.(f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete.Cat-III (Make:-

Honeywell, L&T, Havells, Indoasian, Legrand)

192 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 157.00 Pts 674.68

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following

type erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed..(f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete.Cat-III (Make:-

Honeywell, L&T, Havells, Indoasian, Legrand)

193 Point wiring for Individual Plug with & earth wire of 1.5 88.00 Pts 510.05

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC / Metallic/Wooden box

covered with appropriate front plate modules erected on / in

wall / ceiling as per pipe erected with following type of

accessories. [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm

Cu. Wire from nearby switchboard/mcb db board (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling completeCat-III (Make:-

Honeywell, L&T, Havells, Indoasian, Legrand)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

194 Point wiring for on board Looped Plug with 6A Modular type 158.00 Pts 257.55

switch & 5 pin socket erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall /

ceiling with following type accessories.Cat-III (Make:-

Honeywell, L&T, Havells, Indoasian, Legrand)

195 Providing following type of Modular Type Accessories 3.00 Nos. 160.59

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (3) Two Pin/RJ-11

Telephone Socket[A] For One Gang Cat.III (Make:-

Honeywell, L&T, Havells, Indoasian, Legrand)

196 Providing following type of Modular Type Accessories 3.00 Nos. 160.59

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (4) TV Co-axial

Socket outlet Cat-III (Make:- Honeywell, L&T, Havells,

Indoasian, Legrand)

197 Providing following type of Modular Type Accessories 158.00 Nos. 25.25

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (7) Blank Plate

Single Cat.III (Make:- Honeywell, L&T, Havells,

Indoasian, Legrand)

198 Providing following type of Modular Type Accessories 33.00 Nos. 160.59

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (8) Computer RJ-

45 socket Cat-III (Make:- Honeywell, L&T, Havells,

Indoasian, Legrand)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

199 Providing following type of Modular Type Accessories 61.00 Nos. 180.79

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (9) 16 Amp. SP one

way switch Cat-III (Make:- Honeywell, L&T, Havells,

Indoasian, Legrand)

200 Providing following type of Modular Type Accessories 61.00 Nos. 199.98

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (10) 6/16Amp.

Universal socket Cat-III (Make:- Honeywell, L&T,

Havells, Indoasian, Legrand)

201 Providing following type of Modular Type Accessories 16.00 Nos. 604.99

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site

situation directed by Engineer In charge. (21) Foot Light as

per colour requirement with concealed box, modular

accessories, acrylic glass cover with suitable LED watt with

all accessories as per following module (c) Six modules

Cat-III (Make:- Honeywell, L&T, Havells, Indoasian,

202 Providing and erecting ISI mark Medium class RIGID PVC 1260.00 Mtrs. 33.33

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed (b) 25 mm

203 Providing and erecting ISI mark Medium class RIGID PVC 160.00 Mtrs. 54.54

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed (c) 32 mm

204 Providing & erecting PVC Corrugated Flexible Conduit with 240.00 Mtrs. 21.21

required nos. of coupling, PVC bushes, Check-nuts etc.

complete of following sizes. (2) 25 mm

205 Providing & erecting PVC Corrugated Flexible Conduit with 120.00 Mtrs. 27.27

required nos. of coupling, PVC bushes, Check-nuts etc.

complete of following sizes. (3) 32 mm

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

206 Supplying and laying UPVC cable trunking system 25.00 Mtrs. 428.24

comprising unplasticised polyvinyl, chloride rigid material

with ignition free and flame proof confirming BS with

necessary end caps Internal and external bend, flat bends,

coupler, tee etc..All necessary accessories and measuring of

following sizes (2) 100 mm x 50 mm trunking

207 Providing and erecting Mains with 1.1 KV grade FRLS PVC 5166.00 Mtrs. 82.82

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on

wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of

following size (b) 2 wire 2.5 sq. mm (Make: -RR Kabel,

Havells, Avocab, KEI,Johnson)

208 Providing and erecting Mains with 1.1 KV grade FRLS PVC 2256.00 Mtrs. 112.11

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

2.5 sq. mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following size (A)

with medium class Rigid PVC pipe and accessories (a) 2 wire

4 sq. mm (Make: -RR Kabel, Havells, Avocab, KEI,Johnson)

209 Providing and erecting Mains with 1.1 KV grade FRLS PVC 630.00 Mtrs. 425.21

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

2.5 sq. mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following size (A)

with medium class Rigid PVC pipe and accessories(i) 4 wire

10 sq. mm (use earth wire of 4 sq.mm ) (Make: -RR Kabel,

Havells, Avocab, KEI,Johnson)

210 providing and erecting Mains with ISI marked, 1.5KV grade 150.00 Mtrs. 91.91

electrolyte multi stranded, annealed copper conductor with

heat resistant PVC insulated conforms to IS 694, IEC -

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (f) One wire 10.00 sq. mm

211 providing and erecting Mains with ISI marked, 1.5KV grade 30.00 Mtrs. 300.98

electrolyte multi stranded, annealed copper conductor with

heat resistant PVC insulated conforms to IS 694, IEC -

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (i) One wire 35.00 sq. mm

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

212 Supplying and erecting Flexible PVC insulated multi strand 278.00 Mtrs. 22.22

multi core 1.1 kv grade ISI marked copper wires of following

size to be erected as directed. (c) 1.00 Sq.mm 2 core round/

flat PVC sheathed

213 Supplying and erecting Flexible PVC insulated multi strand 180.00 Mtrs. 46.46

multi core 1.1 kv grade ISI marked copper wires of following

size to be erected as directed.e) 1.50 Sq.mm 3 core round

214 Providing & Erecting approved make following size of TV 135.00 Mtrs. 62.62

Co-axial flexible cable comprising inner conductor of solid

bare copper insulated with Foam PE & Secondary conductor

made of poly - Aluminium film bonded Al. Braids @ suitable

coverage overall sheathed with black PVC insulation. e).RG-

215 Supplying & erecting approved make Telephone Cable 75.00 Mtrs. 20.20

electrolytic copper conductor PE insulation twisted in two

pairs, & wrapped with FRLS PVC tape & sheathed with

FRLS PVC or HFFR outer Jacket suitable for telephone

wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & nos.of pairs. With necessary

connections.[A] Conductor Size 0.5 mm (a) Unarmoured 2)

216 Supplying & erecting approved make LAN cable of following 1056.00 Mtrs. 47.47

size in existing pipe as per direction [C] CAT -

217 Providing & erecting main Distribution (MDF) indoor type, 4.00 Nos. 994.85

back mounted frame as per DoT standard approved with

krone strips(a) Suitable for 10 pair

218 Supplying & erecting M.S. Box having 16 Gauge painted 14.00 Nos. 88.88

with red oxide or Heavy duty PVC box erected flushed on

wall or concealed in wall with necessary plastering &

finishing as directed of following size. (c) 200 mm x 250 mm

219 Providing & erecting Switch board for Computer or electric 33.00 Nos. 1133.22

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with

single mounting base frame covered with textured/metallic

/white front plate,modules erected with necessary connections

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories.Cat-III

(Make:- Honeywell, L&T, Havells, Indoasian, Legrand)

220 Decorative call bell Ting-tong box type 250 volts complete 1.00 Nos. 71.71

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

221 Supplying and erecting LED indoor fittings with LEDs of 313.00 Nos. 373.70

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with

integral/ non-integral driver .(iv) 22-24 Watts, Surge -

2KV,IP-20, conventional 4 feet Cat III (Make:- Wipro,

LT,Philiphs,Havells,Jaquar)

222 Supplying and erecting led lamps with following wattage 45.00 Nos. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp holders,

pf >= 0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder (i) 5 to 8 watts Cat-III (Make:-

Wipro, LT,Philiphs,Havells,Jaquar)

223 Supplying and erecting LED street light / Flood light fittings 20.00 Nos. 4997.48

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (A)

Street Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage

protection.(ii) above 48 to 60 Watts Cat-III (Make:- Wipro,

LT,Philiphs,Havells,Jaquar)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

224 Supplying and erecting LED street light / Flood light fittings 10.00 Nos. 8453.70

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (B)

Flood Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage

protection.(v) above 120 to 160 watts Cat-III (Make:- Wipro,

LT,Philiphs,Havells,Jaquar)

225 Supplying and erecting LED street light / Flood light fittings 2.00 Nos. 4819.72

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (C)

Post Top Lantern LED fitting comprises of finish cast

aluminum spigot and spun aluminum canopy fixed with opal

polycarbonate, pipe arrangement for vertical mounting driver

and accessories wired upto terminal block.IP 65 (ii)32-40W

Cat-III (Make:- Wipro, LT,Philiphs,Havells,Jaquar)

226 Providing and erecting Approved make Four pole moulded 25.00 Nos. 6173.12

case circuit breaker having breaking capacity ICU of 25 KA.

at 415 V,having normal current rating up to 25 A to 100A.

with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

(Make:- Indoasian, L&T (LK), ABB, Schneider)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

227 Providing and erecting Approved make Four pole moulded 5.00 Nos. 8055.76

case circuit breaker having breaking capacity ICU of 35 KA.

at 415 V. having normal current rating 125A. with Fixed

thermal & magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. ICS=100%

of ICU only Cat III (Make:- Indoasian, L&T (LK),

ABB, Schneider)

228 Providing and erecting Approved make Four pole moulded 2.00 Nos. 20946.39

case circuit breaker having breaking capacity ICU of 35 KA.

and above at 415 V . having normal current rating 250A.

with variable thermal & magnetic release suitable to work on

A.C.supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III (Make:-

Indoasian, L&T (LK), ABB, Schneider)

229 Providing and erecting Approved make Four pole moulded 1.00 Nos. 25228.79

case circuit breaker having breaking capacity ICU of 50 KA

and above at 415 V having Normal current rating 400A.

with variable Thermal & magnetic release suitable to work on

A.C.supply 50 c/s. With all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III (Make:-

Indoasian, L&T (LK), ABB, Schneider)

230 Supplying & erecting approved make Four Pole 415V change 1.00 Nos. 22255.35

over switch interior for panel mounting with operating

mechanism A.C.23 duty confirming to IS for (F)400A

(Make:- Indoasian, L&T (LK), ABB, Schneider)

231 Providing and erecting Approved make Earth fault Relay 1.00 Nos. 5415.62

suitable to mount with inter connection suitable to following

size of moulded case circuit breaker having CT ratio &

MCCB rating as following along with shunt trip 220V AC.

with all internal connections & complete erected in existing

M.S.housing. (3) 250 A -400 A , CT Ratio 1/400

232 Supplying and erecting triple pole & neutral 440V / 500V 12.00 Rn.Mtrs 1961.42

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than 1.6 Amp.

/ sq.mm (Rated current / cross section area) duly wrapped

with colour insulating tape for phase sequence of following

current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. (A)

Suitable for 100 Amp. Capacity

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

233 Supplying and erecting triple pole & neutral 440V / 500V 9.00 Rn.Mtrs 3202.71

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than 1.6 Amp.

/ sq.mm (Rated current / cross section area) duly wrapped

with colour insulating tape for phase sequence of following

current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. (B)

Suitable for 200 Amp. capacity

234 Supplying and erecting triple pole & neutral 440V / 500V 2.00 Rn.Mtrs 7319.47

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than 1.6 Amp.

/ sq.mm (Rated current / cross section area) duly wrapped

with colour insulating tape for phase sequence of following

current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. (D)

Suitable for 400 Amp. capacity

235 providing and erecting Miniature circuit breaker single pole 32.00 Nos. 270.68

0.5A to 2A system and having breaking capacity 10 KA to be

erected in existing box. confirming to IS 8828/1996 with ISI

Mark Cat.III (Make:- Indoasian, L&T (LK), ABB,

236 Providing and erecting Miniature circuit breaker single pole 168.00 Nos. 112.11

6A to 25A suitable to operate on 240 V A.C. system and

having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat-III

(Make:- Indoasian, L&T (LK), ABB, Schneider)

237 Providing & erecting 240 V MCB double pole switch for 6.00 Nos. 295.93

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

capacity (B) 40 Amp. Cat-III (Make:- Indoasian, L&T

(LK), ABB, Schneider)

238 Providing & erecting 415 V MCB Four Pole for Motor & 16.00 Nos. 737.30

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following

capacity (B.) for 63 Amp. Cat-III (Make:- Indoasian, L&T

(LK), ABB, Schneider)

239 Providing and erecting Sheet Steel powder coated MCB 14.00 Nos. 2913.85

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (B) three phase

incoming and single phase horizontal type outgoing Per

phase isolation type (PPI) (b) sheet steel double door (ii)6

way (Make:- Indoasian, L&T (LK), ABB, Schneider)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

240 Providing and erecting Approved make RCCBs conforming 42.00 Nos. 2235.13

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max.

rating erected as directed (iI) 40 Amps.DP Cat. III (Make:-

Indoasian, L&T (LK), ABB, Schneider)

241 Providing and erecting metallic vitrified danger notice board 5.00 Nos. 69.69

as per language suggested by engineer incharge for MEDIUM

VOLTAGE installation to be erected as per IS-2551.

242 Providing and erecting Annealed bare Copper wire 8 to 16 30.00 Kgs. 794.87

243 Providing and erecting Pipe type earthing having 150 20.00 Nos. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with coupling

and buch buried in specially prepared earth pit complete with

necessary 8 SWG earth wire.

244 For using salt and charcoal / coke as required for pipe type 20.00 Nos. 171.70

245 Supplying & erecting earth pit of minimum bore dia.150mm 5.00 Nos. 4591.46

size approved make Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free

hot dipped G.I.Pipes having Outer pipe dia of 50mm having

80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of

12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable

for following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation

duly stamped and signed by agency and officer Incharge has

to ensure the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B) Inner

chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be

submitted by Agency. (a) For Electrical Installation up to

440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

246 Providing & erecting weather proof, dust & vermin proof, 9.00 Sq.Mtrs. 14902.55

floor mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet

for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size

of inter connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket,heavy

duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates excludes the

cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams) The panel shall be

supplied with following approved manufacturers with

following size.(B) The standard companies switch gear shall

be used and only manufacturers at CPRI approved factory (i)

with 350mm depth

247 Providing , erecting , fabricating the M.S. structure as per 140.00 Kgs. 77.77

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections complete

with cutting, welding, grinding & finishing duly painted with

one coat of red oxide with erection on site as per direction of

engineer in charge with necessary grouting, cementing,

plastering & finishing complete.

248 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 190.00 Mtrs. 220.18

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (B) 3 1/2 core 35 Sq. mm (

16 Sq. mm 1/2 core) (Make: -RR Kabel, Havells, Avocab,

249 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 120.00 Mtrs. 490.86

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (E) 3 1/2 core 95 Sq. mm (

50 Sq. mm 1/2 core) (Make: -RR Kabel, Havells, Avocab,

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

250 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 360.00 Mtrs. 904.96

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (H) 3 1/2 core 185 Sq. mm (

95 Sq. mm 1/2 core) (Make: -RR Kabel, Havells, Avocab,

251 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured 230.00 Mtrs. 117.16

cable multistrand / Solid Aluminium conductor for 1.1 KV.

to be laid on wall with necessary clamps or in existing trench

/ pipe of following size of cables (A) 4 core 4 Sq. mm (Make:

-RR Kabel, Havells, Avocab, KEI,Johnson)

252 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured 550.00 Mtrs. 140.39

cable multistrand / Solid Aluminium conductor for 1.1 KV.

to be laid on wall with necessary clamps or in existing trench

/ pipe of following size of cables (C) 4 core 10 Sq. mm

(Make: -RR Kabel, Havells, Avocab, KEI,Johnson)

253 Making trench in soft soil of suitable width of 90 cm deep for 455.00 Mtrs. 55.55

laying cable or locating the fault all over the run and back

filling the same and making the surface as normal ground.

254 Making trench in Hard Murrum / Tar Road of suitable width 227.50 Mtrs. 74.74

of 90 cm or required depth for laying any size of cable or

locating the fault all over the run and back filling the same

and making the surface as normal ground.

255 Making trench in Hard Murrum / Tar Road of suitable width 91.00 Mtrs. 357.54

of 90 cm or required depth for laying any size of cable or

locating the fault all over the run and back filling the same

and making the surface as normal ground. (B) If additional

machinery like hammer driller or JCB use [Add]

256 Providing & laying. R.C.C. Hume pipe for cable to be laid 90 60.00 Mtrs. 263.61

cm. below ground across the road crossing or on floor with

necessary material in an approved manner and making the

ground as per original. (E)150 mm dia

257 Providing & laying approved make Double walled 824.50 Mtrs. 62.62

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable (A)

50 mm Outer Dia

258 Providing & laying approved make Double walled 306.00 Mtrs. 137.36

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable (D)

120 mm Outer Dia

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

259 Providing & laying approved make ISI marked Rigid PVC 50.00 Mtrs. 236.34

pipe having 6Kg / cm2 (Class-3) to be erected at road

crossing on or floor as directed for laying of cable. The pipes

as following size of dia & weight per 6 mtr.(F) 110 mm inner

Dia. (11.63 Kg/6 RMT)

260 Providing and, fixing heavy duty flange type brass cable 20.00 Nos. 33.33

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (A) 2 to 4 core 2.5 / 4 Sq. mm

261 Providing and, fixing heavy duty flange type brass cable 44.00 Nos. 38.38

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (C) 2 to 4 core 10 Sq. mm

262 Providing and, fixing heavy duty flange type brass double 8.00 Nos. 75.75

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (B) 3 & 1/2

core 35/50 Sq. mm

263 Providing and, fixing heavy duty flange type brass double 8.00 Nos. 131.30

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.(D) 3 & 1/2

264 Providing and, fixing heavy duty flange type brass double 2.00 Nos. 238.36

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (G) 3 & 1/2

core 185 Sq. mm

265 Solder less crimping type Aluminium lugs conforming to IS 80.00 Nos. 6.06

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (A)

266 Solder less crimping type Aluminium lugs conforming to IS 176.00 Nos. 13.13

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (B)

267 Solder less crimping type Aluminium lugs conforming to IS 32.00 Nos. 20.20

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (D)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

268 Solder less crimping type Aluminium lugs conforming to IS 32.00 Nos. 40.40

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. (F)

269 Solder less crimping type Aluminium lugs conforming to IS 8.00 Nos. 80.80

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. ( I )

270 Providing and erecting Approved make Ceiling fan with 157.00 Nos. 1596.81

double ball bearing ISI mark with condenser A.C. 23OV.50

c/s.1200 mm. sweep complete, canopy erected on existing

hook or clamp with earthing. [Make shall be approved by

Engineer in charge] (Make:- Crompton, Havells, Orient)

271 Supplying and erecting 19 / 20 mm. nominal bore Medium 157.00 Mtrs. 108.07

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leckage and earthing.

272 Supplying & erecting fan hook box of 10 mm M.S. round 157.00 Nos. 108.07

bar bounded to the RCC bars up to 50mm length each side

and pierced through a 16 Gauge M.S. box / Heavy Duty PVC

box complete erected concealed in Ceiling with necessary

273 Supplying & erecting single phase approved make industrial 40.00 Nos. 2054.34

exhaust fan suitable for medium duty ring mounted low noise

operation suitable for medium duty having following dia size

and maximum speed in RPM [A] 305 mm dia 900 RPM

Cat.II (Make:- Crompton, Havells, Orient)

274 Supplying and erecting approved make Octagonal pole made 20.00 Nos. 8192.11

from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for cable

termination to be erected With Suitable foundation

(Included) as per details given by manufacturer considering

site requirement.(D) 6 Mtr. Long 70 mm Top X 135 mm

bottom dia, 3 mm thickness with 200mmX200mmX12mm

base plate, 4-M20 Bolts and 600mm long with necessary G.I.

J Bolts .Approx Pole weight 59 kg

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

275 Supplying & erecting approved make SMC press moulded 12.00 Nos. 515.10

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip 5way(3P+N+E),DIN

rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.(b) 250mm x

200mm x 100mm [deep]

276 Providing street light pole bracket comprising main B Class 20.00 Nos. 561.56

MS pipe of 4.2 cm/require outside dia. complete with suitable

B Class M.S. sleeve tubing of approx. 45cms.length and

suitable for 76.5 mm / 80mm. / require size pole top having

sufficient fastners for fixing the brackets and having spread of

1 mtr. length with suitable rise as per site condition &

suitable welded stiffener reducer and nipple with check nut

complete painted with one coat of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint with

following nos of arms. [A] Single Arm bracket 1 Mtr

277 Supplying & erecting approved make Digital time switch 2.00 Nos. 3168.37

having lithium cell 6 years operative and operate battery

backup 1 channel day clock with 14 memory programme,

suitable to operate on 240V + 5%, 16A with, floating contacts

Minimum switching setup time 1 minimum & LCD display.

Also comprised permanent ON/OFF switching. Programming

switches & housed in fire proof thermoplastic enclosure &

transparent cover erected as required with necessary

connection erected as directed.

278 Supplying & erecting power contactor ,AC3 duty for time 2.00 Nos. 2782.55

switch complete erected as per direction Cat III (Make:-

Indoasian, L&T (LK), ABB, Schneider) [D] 4 pole 440V

279 Providing & Erecting full SS Body (SS 304) Split type water 5.00 Nos. 61115.10

cooler having storage capacity 160 to 175 Ltr.(Tank SS 304)

& Cooling capacity 150 ltr. Per hour @ an ambient temp of

350 C.The outlet temp. of the water should drop by 150C

within a hour,The water cooler should be comprising of

hermetically sealed Reciprocating compressor with R134A,

fan motor, Copper Condensing unit with company fabricated

Outdoor Unit water tank surrounded by evaporating coil,

thermostats, relay etc.complete with necessary copper tube &

Insulation, M.S Chanel Stand with Painting for water tank &

M.S. Powder Coated Stand for Outdoor unit with Installation.

With DPELCB and 4 Way DB Box with accessory Three core

Cord for connection.(Make:- Blue Star,Usha,Voltas)

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

280 Supplying and erecting water filter cum purifier with ultra 5.00 Nos. 5424.71

violate technology. (Aquaguard / waterdoc model or

equivalent symphony/ crystal/videocon model)

281 Supplying & erecting 5 stage single reverse osmosis water 5.00 Nos. 29187.99

purification system with M.S. powder coated frame, prefilter

housing with 'O' ring presediment filter GAC filter, carbon

filter suitable buster DC pump capacity 80 psi, mention with

40 psi inline type post carbon filter auto low & high pressure

switches with following size of storage tank & LPH capacity

& erected as directed[C] 50 Ltr / Hr with 150 psi 2 nos

282 Supplying and erecting horizontal / vertical mounting type 20.00 Nos. 11455.42

storage water heater with copper container housed in

M.S./S.S./ABS body insulated with glass wool/puff complete

with heating elements,adjustable thermostats 300C to 850C,

indicating lamp, safety valve, fusible plug, etc.complete

erected with coach bolts, nuts. washers & cementation (C)25

Ltr. with 2 KW. heating element Premium Category

283 Supplying and erecting chromium plated heavy duty brass 20.00 Nos. 181.80

valve for inlet pipe of water heater 15 mm dia.)

284 Supplying and erecting 15mm brass non-return valve for 20.00 Nos. 232.30

inlet pipe of storage water heater.

285 Supplying and erecting dead pressure releasing valve for 20.00 Nos. 385.82

storage type water heater with necessary materials.

286 Providing & erecting fibre reinforced PVC flexible pipe with 80.00 Rmts. 181.80

brass locking nuts & washers & clips at both ends complete

erected without leakage

287 Supplying, installing, testing & commissioning of SOLAR 5.00 Nos. 189956.76

WATER heating system as per prevailing IS code comprising

of Solar flat locket collector, stainless steel hot water storage

isolated tank with S.S. heat exchanger, absorber made of

copper sheet & copper tube of following capacity in liter / day

(LPD) with "B" size aluminium box collector with

appropriate capacity electrical backup arrangement

(Excluding inlet & outlet pipe lines) (E) Capacity of

288 Supplying & erecting resin bonded flap rock wool / glass 450.00 Mtrs. 767.60

wool with conductivity valve 1.67 sq.mm per watt & to with

stand the temp. to 100 degree centigrade C thickness 50mm

with G I pipe of following size dia "B" class as per IS:1239.

The plastic sheet to be used as covering of glass wool. Al.

cladding besides other materials like chicken mesh, 26 G Al.

Sheet shall be used for cladding the insulation pipe.(E) for

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

289 Supplying and erecting approved make panel mounting type 5.00 Nos. 1275.63

Digital Voltmeter having 3 digits LED display, 0 to 750 AC

Volts range erected on existing panel board with all

connection, wiring etc .with manufacturers calibration

290 Supplying and erecting approved make panel mounting type 5.00 Nos. 1558.43

Digital Ammeter having 3 digits LED display, external CT

operated, calibrated for 0 to 1000 Amps suitable to operate on

500 Volt AC , erected on existing panel board with all

connection, wiring etc .with manufacturers calibration

291 Providing & erecting L.T. Current Transformer with bar 15.00 Nos. 274.72

primary 50/5 to 1000/5 ratio 15 VA burden erected in existing

CRCA box duly secured with insulating materials connected

292 Supplying and erecting approved make suitable panel 15.00 Nos. 43.43

indicator LED type lamp, lens cover, complete erected with

necessary connections.

293 Providing & erecting open well horizontal mono block pump 2.00 Nos. 15707.52

set with cast iron body, complete for three phase submersible

motor having[C] For 3 HP 3 phase open well horizontal

mono block pump set suitable for 85 LPM to 270 LPM @

mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe

Cat.II (Make:- Crompton, Lubi )

294 Supplying & erecting approved make motor control cubical 2.00 Nos. 7722.46

panel (Direct - on - line) made from 16 G. CRCA sheet duly

epoxy powder painted inside and outside with hinged doors

and locking, arrangement consisting of suitable size of ON-

OFF isolator (AC - 3/23duty) main fuses, single phasing

preventer, indicating lamps for R- Y - B phases, overload

relay, Automatic water level controller, Ammeter, Voltmeter

each with two way selector switch incoming, wires duly

socket crimped, main contactor & overload relay, start - stop

push buttons, to be erected on angle iron frame grouted on

wall as directed. The isolator, overload relay & contactors

will be of L & T, Siemens or BCH make only.(A) DOL up to

295 Providing and erecting ISI marked PVC insulated PVC 90.00 Mtrs. 146.45

Sheathed Flat flexible Submersible copper cable approved

make of following Size. (C) 3 Core x 4 Sq. mm

296 Providing Water proof straight Joint in PVC insulated flat 2.00 Nos. 189.88

flexible copper cable by using insulating material, water

proofing material, & making the joint complete. (A) Up to

297 Supplying of following size of HEAVY UPVC column pipe 30.00 Rmts. 359.56

with coupler and wire lock [B] 50 mm dia

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

298 Supplying, & erecting C.I. swing, check type non-return 2.00 Nos. 1020.10

(Reflux) Valve -ISI marked suitable for following size (A)

299 Supply of following size of TOP & BOTTOM accessories i.e. 2.00 Per Set 1489.75

Adaptor set (CI) long, pump guard set, starter pipe Rubber

ring for submersible pump & UPVC column pipe as directed

by Engineer - in - charge with necessary plumbing as

desired.[D] 50 mm dia

300 Supplying, Erecting, Testing & Commissioning the passenger 1.00 Nos 1575617.17

/ stretcher lift having following main features:[1] GEAR

LESS LIFT DRIVE (MRL) comprising of High Starting

torque Lift 3 phase 440 V A. C. Permanent Magnet

Synchronous motor of proper rating with high efficiency shall

be used.[2] Micro processor based / PLC, ACVVVF, vector

control drive with encoder feedback closed loop system shall

be used for lift car and door operation which shall be full

collective selective operation hall call demand response,

UP/DOWN hall stops, Main, Up/ Down Contactor with

overload and phase reversal relay and safety controls. [3] Car

with M S platform with bracings of adequate size and to

sustain the impact load cabin + passenger with safety factor

of fire for steel and side panels of Stainless steel of sheet of

grade 304 duty. Car ceiling will be S.S. finishes with aesthetic

appearance with LED ceiling lights. Car flooring shall be of

s/s 304 chaker plate design sugeested of engineer in charge.

of engineer in charge. Car doors shall be of stainless steel

grade 304, hairline finish with centre opening / telescopic

automatic doors. Car panel will also be S.S. 304 finished with

emergency stop device, mechanical door safety device,

facility of auto/ attended mode. All car panel buttons and all

floor switches must be with brail language as per lift act.[4]

All landing doors must be fire rated for 2 hour shall be fully

automatic centre opening/ telescopic opening made of hairline

finish steel grade of 304 with key holes and infrared curtains

with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency

Light & Fan should start immediately without any Time

Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow

along with floor position indicator shall be provided inside

the car and at all floors.

[7] Full height infra red curtain with multiple cross / crossing

light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided

accordingly of passenger capacity with Manual Rescue

grade 304, hairline finish with centre opening / telescopic

automatic doors. Car panel will also be S.S. 304 finished with Estimated

Rates Total Amount

Rates Total Amount

Item emergency stop device, mechanical door safety device, according

Item of work Quantity Unit In figure

No. facility of auto/ attended mode. All car panel buttons and all to estimated

floor switches must be with brail language as per lift act.[4] Rs. Ps. quantities

All landing doors must be fire rated for 2 hour shall be fully

automatic centre opening/ telescopic opening made of hairline

finish steel grade of 304 with key holes and infrared curtains

with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency

Light & Fan should start immediately without any Time

Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow

along with floor position indicator shall be provided inside

the car and at all floors.

[7] Full height infra red curtain with multiple cross / crossing

light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided

accordingly of passenger capacity with Manual Rescue

Operation ( Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open till excess

load is removed. [10] Spring buffers/PU Buffers shall be

[11] Car fan as per passenger capacity with automatic sleep

timer shall be provided.

[12] Voice annunciator with suitable music shall be provided

[13] Self diagnostics system for operational and safety

parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and submission of

calibration certificate submission, door key holes in the floor

doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine

room and monkey ladder for lift pit should be provided by the

lift agency, along with the other steel structure works,

foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided without

any extra cost, where ever required as / if directed by engineer

in charge. [17] Permanent wiring with

necessary safety devices like RCCB in all circuit, Over

Voltage Under Voltage protection and THD eliminator in

circuit for lift machine room and lift well with proper

numbers of light points, with fixtures, exhaust fan and plug

points shall be provided by the agency. Only 3 phase Power

Supply shall be made available by department in lift machine

room. Necessary Earthing as per Lift Act/Rules shall be

arranged by Lift Agency.

[18] Any civil/ electrical works for additional and alteration

[11] Car fan as per passenger capacity with automatic sleep Estimated

Rates Total Amount

Rates Total Amount

timer shall be provided.

[12] Voice annunciator Item of workmusic shall be provided Quantity

with suitable Unit In figure to estimated

in lift car. Rs. Ps. quantities

[13] Self diagnostics system for operational and safety

parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and submission of

calibration certificate submission, door key holes in the floor

doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine

room and monkey ladder for lift pit should be provided by the

lift agency, along with the other steel structure works,

foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided without

any extra cost, where ever required as / if directed by engineer

in charge. [17] Permanent wiring with

necessary safety devices like RCCB in all circuit, Over

Voltage Under Voltage protection and THD eliminator in

circuit for lift machine room and lift well with proper

numbers of light points, with fixtures, exhaust fan and plug

points shall be provided by the agency. Only 3 phase Power

Supply shall be made available by department in lift machine

room. Necessary Earthing as per Lift Act/Rules shall be

arranged by Lift Agency.

[18] Any civil/ electrical works for additional and alteration

in lift shaft and machine room related to erection of lift shall

be made by lift agency without any extra cost. (granite/marble

fixing around all landing door openings are not in lift

agency’s scope.)

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all necessary

permission from lift inspector and other authorities. [20]

acrylic transparent licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of Gujarat lift &

escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift

erection and provide report by third party authorized by

concern licensing authority 5.agency has to provide third

party insurance upto completion of free maintenance period

and submit the document for the same.[21] Car Panel

Operating Buttons with floor position indicator/buttons must

be of Auto Glow type clearly visible when view from inside

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should be

provided at appropriate height on the Rear & Side Wall

room. Necessary Earthing as per Lift Act/Rules shall be

arranged by Lift Agency. Estimated

[18] Any civil/ electrical works for additional and alteration Rates Total Amount

[18] Any civil/ electrical works for additional and alteration Rates Total Amount

in lift shaft and machineItem

work to erection of lift shall Quantity Unit

No. In figure to estimated

be made by lift agency without any extra cost. (granite/marble Rs. Ps. quantities

fixing around all landing door openings are not in lift

1 agency’s scope.) 2 3 4 5

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all necessary

permission from lift inspector and other authorities. [20]

acrylic transparent licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of Gujarat lift &

escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift

erection and provide report by third party authorized by

concern licensing authority 5.agency has to provide third

party insurance upto completion of free maintenance period

and submit the document for the same.[21] Car Panel

Operating Buttons with floor position indicator/buttons must

be of Auto Glow type clearly visible when view from inside

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should be

provided at appropriate height on the Rear & Side Wall

Panels in Lift Car. [23] With Necessary KVA rating voltage

controlled Stabilizer suitable for your controller, drive and all

equipments of lift.

[24] Necessary rating of DP Elcb and FP Elcb required for lift

is in scope of work which rating is sugested by CEICED

Department (electrical Inspector)

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for

PREMIUM category 1. Advanced control system

dual 64 bit embedded microprocessor with CANBUS Serial

Communication mode including Regenerative power efficient

operation,on site programming facility, Anti nuisance, Pte-

opening, BMS/RMS with necessary online real time

monitoring system having necessary connectivity for remote

monitoring & other suitable supporting hardware & software

devices to fulfil the purpose. 2. Floor Indication LCD Display

with call registration & brail mark with arrival gong and hall

lantern & TFT Screen in the car with MP3 Voice Announcer.

3. CAR Panel should be Scratch resistive SS Moonrock

finish / Hair Line / Honeycomb for car and all Doors, All

landing doors must have fire rating up to 2 hours and car door

must have multi-level crisscross beam door protection.

To & fro communication system & wiring (i.e. car , control

room & guard room ) and Each elevator are equipped with

remote monitoring system.agency has to provide mobile app

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should be Estimated

provided at appropriate height on the Rear & Side Wall Rates Total Amount

provided at appropriate height on the Rear & Side Wall Rates Total Amount

Item Panels in Lift Car. [23] With Necessary KVA rating voltage according

Item of work Quantity Unit In figure

No. controlled Stabilizer suitable for your controller, drive and all to estimated

Rs. Ps. quantities

equipments of lift.

1 [24] Necessary rating of DP Elcb 2 and FP Elcb required for lift 3 4 5

is in scope of work which rating is sugested by CEICED

Department (electrical Inspector)

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for

PREMIUM category 1. Advanced control system

dual 64 bit embedded microprocessor with CANBUS Serial

Communication mode including Regenerative power efficient

operation,on site programming facility, Anti nuisance, Pte-

opening, BMS/RMS with necessary online real time

monitoring system having necessary connectivity for remote

monitoring & other suitable supporting hardware & software

devices to fulfil the purpose. 2. Floor Indication LCD Display

with call registration & brail mark with arrival gong and hall

lantern & TFT Screen in the car with MP3 Voice Announcer.

3. CAR Panel should be Scratch resistive SS Moonrock

finish / Hair Line / Honeycomb for car and all Doors, All

landing doors must have fire rating up to 2 hours and car door

must have multi-level crisscross beam door protection.

To & fro communication system & wiring (i.e. car , control

room & guard room ) and Each elevator are equipped with

remote monitoring system.agency has to provide mobile app

and user id and password for monitoring. 8 / 10 Passengers,

Ground plus 3 upper floor with Rated Speed of 1.0 m/sec.,

(C) With General PLUS ADDITIONAL SPECIAL

FEATURES attached herewith. Prem. Cat.

Total Cost of Construction Cost

Five Crore Seventy Eight Lakh Fifteen Thousand Seven Hundred Three Rupees and Ninety Two Paise Only

Deputy Executive Engineer Executive Engineer

R&B Sub Division R&B Division

Idar Himatnagar

I/We am/are willing to carry out the work at ………………………………………………..% above/below (percent

should be written in figures and words) of the estimated rates mentioned above. Amount of my/our tender works out

*Estimated amount *Estimated amount

Put to tender Rs…57815703.92 Put to tender Rs.57815703.92

Deduct ……. % below Rs……………………..…. Add ……. % Avove Rs…………..….

Net Rs. …………………….… Total Rs. ………….…

The Contractor shall exhibit a board with detailed specification and details of work as directed by

the Engineer-In-Charge for which no extra payment shall be made.

Rates Total Amount

Rates Total Amount

Item of work Quantity Unit In figure

No. to estimated

Rs. Ps. quantities

The labour cess will be deducted as per prevailing rules i.e. 1% of the work done

3 GST and Income tax TDS will be deducted at a source while making payments of bills.

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt.G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there

4 is a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

R&B Sub Division R&B Division

Idar Himatnagar