REP TO WATER PROOFING SUNKEN FLOOR, REPLACEMENT OF INT WATER SUPPLY PIPE LINE SANITARY FITTINGS IN MD AND OTM ACCN AT SRC, MH, MDC, ASC, SHO, STORE AREA REP REPLACEMENT OF FLOORING DADO PLINTH PROTECTION CERTAIN MISC BR WKS AT RAMGARH CANTT

Amount

Demoliton of cement concrete in ground floor paving not exceeding 15cm thickness (below or above ground level ) including removing of rubbish off the premises complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing of rubbish off the premises complete all as specified and directed.

Dismantling stone slabs of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, and removal of debries from site complete all as specified and directed.

M&L for Plain Cement Concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base of flooring etc complete all as specified and directed.

M&L for Plain Cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in levelling course, coping, window cill including necessary formwork complete all as specified and directed.

M & L for 40 mm thick PCC (1:2:4), type B - 1 (using 20 mm graded crushed stone aggregate) as in floor finishing,even & smooth using extra cement including fixing of glass strip complete all as specified and directed. Note: Glass Strip shall be measured and paid separately under respective item of BOQ.

Supply only 38mm wide glass dividing strips, 3mm thick complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6, type C-2( using 40mm graded crushed stone aggregate) including finished surface even & fair without using extra cement as in plinth protection including necessary formwork for edges complete all as specified and directed. Note: 10mm wide and 75mm deep joints shall be made at 3 mtr intervals and at each corner and the same shall be filled with mixed 85/25 grade bitumen and sand in the ratio 1:3 complete all as specified and directed.

M&L for non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm in floors etc, over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed

M&L for coloured ceramic glazed tiles 375mm x 250 mm x 7mm/ 450 mm x 300 mm x 7mm thick, laid in vertical surface as in dado/skirting etc, over & including 10 mm thick rendering in CM 1:4, set & jointed in neat cement slurry & pointed in white or coloured cement complete all as specified and directed.

M&L for coloured non digital paver vetrified exterior tiles 10 mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.18 sqm in floors etc, over & including 15mm thick screed bed in CM 1:6, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed

M&L for 10mm thick Light shade vitrified ceramic tiles polished area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm as in floors,set & jointed in neat cement slurry and pointed in coloured cement to match, over & including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 10mm thick Light shade vitrified ceramic tiles polished area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm, laid in vertical surface as in dado/skirting etc, over & including 10 mm thick rendering in CM 1:4,set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L for 10mm thick Light shade vitrified ceramic tiles polished area of each tiles not exceeding 0.36 sqm as in floors,set & jointed in neat cement slurry and pointed in coloured cement to match, over & including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 10mm thick Light shade vitrified ceramic tiles polished area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm laid in vertical surface as in dado/skirting etc over & including 10 mm thick rendering in CM 1:4,set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18mm -20 mm thick of size not less than 575 mm X 575 mm, over laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing & polishing with Bee wax polish, over & including 20 mm thick screed bed in CM (1:6) complete all as specifed & directed.

M&L for machine cut kota stone slab in skirtings,riser of steps ,dado & pillar 10 to 12 mm thick laid and jointed with grey cement slurry pointed with cloured cement to match the shade of the slab including grinding rubbing & polishing with Bee wax polish, over 10 mm thick backing coat in CM (1:4) etc complete all as specifed & directed.

Demolition of cement concrete reinforced as in chullah hoods , shelves and plate form etc complete all as specified and directed

M&L for RCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in kitchen platform,shelf etc including necessary form work complete all as specified and directed.

S&F mild steel TMT Fe 500 D bars 8 mm dia and over cut to length bend to shape required including cranking bending spirally for hooping for columns, hooking and binding with and including mils steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for marble work of any shade 16 to 18mm thick in cooking platform, steps, windowcills, etc over and including 15mm thick cement screed base in CM 1:4, laid and jointed with white cement slurry mixed with admixture of pigment to match the shade of the slab including rounding of existing slab including demolition of old slab complete all as specified and directed.

M&L for Granite (of any type) work (table rubbed and polished) of any shade 18 to 20mm thick in cooking platform, steps, window cills, etc over and including 15mm thick cement screed base in CM 1:4 laid and jointed with white cement slurry mixed with admixture of pigment to match the shade of the slab including rounding of slab including demolition of old existing slab complete all as specified and directed.

Grinding & Polishing with bees wax of existing kota stone/ Terrazo flooring, etc including treating the surface with beeswax polish complete all as directed by Engr-in-charge

Taking down cement plaster on wall of any description including racking out joints hacking for key and scrubbing down with water including removal of rubbish off from the premises complete all as specified and directed.

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off MOD land etc complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius build in cement mortar 1:6 complete all as specified and directed.

All as per item no 26 here in before but except bricks. Note: Bricks obtained from item No. 25 of BOQ here in before.

M&L for 15mm thick rendering on fair faces of brick /concrete surfaces in CM (1:6), finished even and fair (Without using extra cement ) complete all as specified and directed.

M&L for applying three coats of white wash on newly plastered surfaces on wall including preparation of surfaces complete all as specified and directed.

M&L for preparation of new plastered wall surface and applying two coats of oil bound distemper over a coat of alkali resistant primer and a layer of wall care putty (not less than 2 mm thick) complete all a s specified and directed.

Taking down existing complete roof /parapet treatment any thickness including mud phuska, plastering, leaping plaster of any thickness cuting & up rooting tree roots/Vegitable growth & removing the debris from the premises upto 500m from the MOD land including cleaning/washing down and keeping surfaces clean complete all as specified and as directed.

M & L for brushing neat cement slurry (@ 3 Kg of cement per Sqm) for bonding of old concrete surface to new concrete, complete all as specified and as directed.

M & L for plain cement concrete 1:2:4 ,type B-0 (using 12.5mm graded crushed stone aggregate) mixed with integral water proofing chemical compound, mixed in proportion 200 milli litre per 50 Kg of cement as in padding, benching, sunken portion etc., on roof surface for correcting/making proper slope on roof, etc.,complete all as specified and directed .(Note:Water proofing compound shall be measured and paid seprerately under respective item of "BoQ")

M & L for cutting 75 mm wide and 65 deep in brick wall/PCC block/RCC surface any location shaping horizontal face groove filled with PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) with and including chemical compound mixed in proportion 200 mili litre per 50 Kg of cement or as per manufacturer's instructions laid when concrete is still green, complete all as specified and as directed. Note:Water proofing compound will be measured and paid seprerately under respective item of "BoQ".

M & L for application of water proofing treatment using APP modified roof membrane over non accessible/ non approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface) to be executed through approved applicator of the membrane manufacturer/authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly with wire brush & applying 10 mm thick plaster /rendering in cement mortar (1:3)mixed with integral water proofing chemical compound, mixed in proportion 200 milli litre per 50 Kg of cement (b) Applying approved bituminous based primer( conforming to IS: 3384-1995) @ 0.50 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Applying two coat of bituminious based Aluminium Paint @ 0.3 Kg /sqm over APP Membrane.

Supply only liquid water proofing compound ISI marked. complete all as specified and directed.

M & L for application of water proofing treatment using APP modified roof membrane over accessible/ approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface) to be executed through approved applicator of the membrane manufacturer /authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning existing surface properly & apply 10 mm thick plaster /rendering in cement mortar (1:3) with WPC as per manufactures instructions (b) Applying approved bituminous based primer( conforming to IS: 3384-1995) @ 0.30 litre / Sqm manufactured by the same agency as that of APP membrane with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface er . (c) Laying not less than 3mm thick APP (Atactic polypropylene Polymer modified prefabricated membrane) modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gms/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.00 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gms/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 150 Kg / Sqcm and transverse not less than 450 Kg /Sq.cm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP modified polymeric membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Applying two coat of hot air blown grade bitumen of grade 85/25 @ 1.20 Kg /sqm over APP Membrane complete all as specified and directed

M & L for machine pressed cement concrete tiles 25cmX25cm X 22mm thick/ 30 cm x 30 cm x 22 mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment ,laid over and including 15mm thick cement screed bed in cement mortar (1:6) complete all as specified and directed.

M& L for applying evenly a tack coat of industrial bitumen 85/25 grade at the rate of 1.20 kg per sqm in sunken portion including cleaning of surfaces complete.after treatment the same shall be tested for leakage/seepage/dampness by ponding with water for 72 complete all as specified and as directed. hours

M & L for PCC (1:5:10), type E-2 (using 40 mm graded brick aggregate) as in sunken portion, sub-base, etc., complete all as specified and as directed.

S &F in repair 50mm bore tubes light grade galvanised with all fittings laid in floor as in spout pipe, etc complete all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frames) of any description not exceeding 1.5 Sqm each, complete all as specified and directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engineer-in-Charge.

S & F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube for top and bottom rails. mild steel framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as fixing in the frame at site as per specification and drawing complete all as specified and as directed.

S & F 100mm size butt hinges medium weight cold rolled stainless steel (SS) complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 150 mm long aluminium alloy handles of extruted section type, anodised complete all as specified & directed.

S & Fin repair health faucet(ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 m long flexible tube and ABS wall hook including making connection & fixed in position complete all as specified & directed.

M&L for demolition of cement concrete (un reinforced ) in ground floor, terrazo tiles floor & paving of exceeding 15cm thickness (above or below ground level ) by mechanical tools and removing excavated material outside of MoD land, complete all as directed by Engr-in-Charge.

Taking up or down steel tubing and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

Taking up or down steel tubing and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 15 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

S&F for GI water tubing medium grade, ISI marked, galvanised, 20 mm bore with all fittings, (such as tee, elbow, socket, union & short pieces) fixed to walls and ceiling or laid in floors including cutting chases for brick walls and making good the surface in cement mortar 1:3 complete all as specified & directed.

Refixing for 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)including all fitting as socket, elbow, nipple,union etc complete all as specified and directed .

Refixing for 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling,floors, etc.)including all fitting as socket, elbow, nipple,union etc complete all as specified and directed .

S & F in repair for PVC connection pipe of 15 mm dia and 45 cm long to WHB and flushing cistern complete all as specified and directed.

S & F in repair angle stop valve of 15mm bore, chromium plated fancy type and cup cast copper alloy, screwed down, high pressure, with crutch handle, screwed both ends for brass ferrule complete all as specified and directed.

S&F in repair for Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S&F in repair for Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S & F in repair, 15mm bore bib taps ( weight not less than 400 gm) cast copper alloy, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and directed.

S & F in repair, 15mm bore stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed) screwed down,high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

S & F in repairs brass chromium plated shower rose with swivel joints, 125 mm size in square with chromium plated long shank arm including fixing to steel pipe or union complete all as specifed & as directed.

S&F WC squatting pan " Orissa Pattern" of size 580 mm X 440 mm white with integral foot rest including cast iron "P" or "S" trap, front or back inlet and making connection to trap & to flushing cistern complete including taking down existing pan & making good disturbed surface complete all as specified & directed.

M&L vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device including plastic seat cover & taking down existing pan & making good disturbed surface complete all as specified & directed.

S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including all standard accessories such as inlet ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F in repair vitreous China wash basin, any colour, flat back size 550 mm X 400 mm including 32mm brass chromium plated waste coupling , 32 mm bore PVC waste pipe, chromium plated Grating including cutting for & pinning in ends of bracket or errecting bracket & PCC 1:2:4 ,type B-1(using 20 mm graded crushed stone aggregate) for embedding brackets & making good disturbed surface with CM 1:3 complete all as specified and directed.

S & F in repair pillar taps long body chromium plated, cast copper alloy with capstan head, chromium plated, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed

S & F in repair shelf 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 300 gms), complete all as specified and as directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf, 12cm wide with chromium plated bracket guard and railing 60cm long complete set complete all as specified and directed.

S&F in repair towel rail brass chromium plated towel rail , 20 mm dia ,D-type 600 mm long between flanges fixed with and including chromium plated brass screw & wooden /plastic cleats complete set all as specified and directed.

S & F in repair for 110mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

S&F in repair for 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

S&F in repair for PVC (SWR) bends 110 mm bore of any radius complete all as specified & directed.

S&F in repair PVC (SWR) bends 75 mm bore of any radius complete all as specified & directed.

S&F in repair PVC (SWR) junction single (single-T) equal or unequal 110mm bore provided with access door complete all as specified & directed.

S&F in repair PVC (SWR) junction single (single-T) equal or unequal 75mm bore provided with access door complete all as specified & directed.

S&F in repair 110 mm bore PVC (SWR) vent cowl complete all as specified & directed..

M&L for 75mm outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement with chromium plated grating with or without hole including taking down existing trap complete all as specified and directed.

S & F in repair 110 mm dia PVC(SWR) WC connector with lip ring, complete all as directed and as specified.

S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) including taking down of existing tank complete all as specified and directed.

S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) including taking down of existing tank complete all as specified and directed.

Disconnecting existing tanks exceeding 250 ltr but not exceeding 500 Ltr capacity setting aside (or lowering if required) for repairs, cleaning etc. and hoisting ,if required reconnecting and re-fixing in position. complete all as specified. Note : Ccleaning ,repairing, etc measured & paid separately under respective items of BOQ .

Disconnecting existing tanks exceeding 500 ltr but not exceeding 1000 Ltr capacity setting aside (or lowering if required) for repairs, cleaning etc. and hoisting ,if required reconnecting and re-fixing in position. complete all as specified. Note : Ccleaning ,repairing, etc measured & paid separately under respective items of BOQ .

M&L for preparing the newly plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

simplex infra project (BID ID -3328665)

M/S KAMLESHWAR SINGH (BID ID -3330136)

M/S PARAS NATH SINGH (BID ID -3330412)

M/s friend enterprises (BID ID -3329999)