SPECIAL REPAIR TO CERTAINSINGLE LIVING OFFICERS ACCOMMODATION, PROVISION OF CERTAIN WORKS SERVICES AT LGS SECTION AND ADDN/ALTN TO STORAGE SHED AT AIR FORCE STATION BAREILLY

Amount

Removal to existing treatment from roof including brick tiles laid dry etc any thickness or description complete and remove from site to low laying area in camp except brick bats complete all as specified and directed.

Demolition of Mud in roof any thick including plastering & leeping (whether full thickness removed or only a part thereof) complete and remove from site to low laying area complete all as specified and directed.

M&Lfor roughening existing roof surface and provide PCC type B-1 1:2:4 mix (using 20 mm graded stone agg) as in levelling coarse complete all as specified and directed.

M&L for Providing 90-100 micron thick polymeric water proofing membrane over levelling coarse on non -approachable roof with following Specifications : (i) Average 10mm thick plaster in CM 1:3 mixed with polymer based water proofing compound when levelling coarse is still green. (ii). After the surface is fully dried, it shall be cleared with free form dust and shall be painted a coat of bituminous primer @ 0.30 liters/Sqm. (iii). After primer, the entire roof surface shall be applied with hot, blown bitumen grade 85/25 confirming to IS-702 @ 1.2 Kg/Sqm (iv). Over hot bitumen, polymeric water proofing membrane consisting of 90 to 100 micron thick central core of HMHDPE film and standard weight 3 Kg/Sqm shall be laid with 100mm side lap/end lap on prepared surfaces as per manufacture’s instruction and strict supervision of manufacture’s technical representation. (v).Laying 40mm thick brick tiles laid over a bedding layer of 20mm screed in cement mortar 1:4. The cement mortar screed shall be mixed with polymer based liquid water proofing compound @ 5% by weight of cement or as per manufacturer’s specification /instructions and tiles joints shall be filled with polymer based cement proof joint filler manufactured by approved specification / instructions and tiles joints shall be filled with 1:3 CM mixed with crude oil as per SSR-2009 (Part-1) complete all as specified and directed.

M&L cutting out crack in V section in existing roof ,chajjas or similar work up to 40 mm deep and cleaning the same with water jets to get rid of any loose material and wetting ,grouting with cement & sand morter 1:3 mixed with liquid WPC all as directed .

M&L plain cement concrete type B-1 1:2:4 mix (using 20 mm graded stone agg) as in coping, parapets , bed plates, kerb and the like rounded or chamfered on edges complete all as specified and directed.

Demolition of cement concrete (un-reinforced) any description and in any position not otherwise specifically provided for complete all as specified and directed.

Disconnecting existing tank not exc. 1000 Litre capacity, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position (cleaning, repairing etc. to be measured separately) complete all as specified and directed.

Dismantling of water tank n exc 1000 ltrs complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, (measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 ltrs capacity hoisted and fixed in position all as specified and directed in SSR Pt I complete .

S & F in repair 20 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gram) complete all as specified and directed.

Taking up or down 15/20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed

S&F 15 mm bore of galvanised steel tubing medium grade with all fittings complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm bore of galvanised steel tubing medium grade with all fittings complete to walls and ceilings or laid in floors complete all as specified and directed.

Refixing old 15 mm GI tubing and connection in new or old location after taking down ,cleaning etc complete 20 mm bore complete all as specified and directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, including removal to stores and accessories complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) pipes (IS 13592-1992 type A) single socketed , in any length with rubber ring joints conforming to IS-5382 fixed to walls with SS clamps complete all as specified and directed.

S&F for PVC (SWR) bends with access door any radius of bore 110 mm complete all as specified and directed.

S&F PVC (SWR) bends any radius of bore 110 mm complete all as specified and directed.

S&F in repairs cast iron floor trap long neck type 75 mm dia without grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

S&F in repairs 75 mm dia bore cast iron sand cast soil waste and vent pipe in any length with or without ears, with lead joint laid in tranches or in floor complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan (padestal pattern) white excluding flushing cistern but incl PVC flush pipe & sheet cover closed pattern and fixing kit complete all as specified and directed. Make: Parryware, Cat Part No : C0297 or equivalent make as approved by GE

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded crushed stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M&L for 15 mm thick rendering in cm (1:4) on brick or concrete surfaces, up to 3.0 M height including steel scaffolding , finished fair and even including mixed with liquid WPC as per manufacturer instruction complete all as specified and directed. Note :- WPC will be measured and paid separately.

M&L for 15 mm thick rendering in cm (1:4) on brick or concrete surfaces, fom 3.0 M to 7.0 M height including steel scaffolding, finished fair and even including mixed with liquid WPC as per manufacturer instruction complete all as specified and directed. Note :- WPC will be measured and paid separately.

M & L for 15 mm thick rendering on fair faces /unfair surface of brick work or concrete surfaces with cement mortar 1:6 finished even and fair complete all as specified and directed.

M & L for 15 mm thick rendering on fair faces /unfair surface of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6, in patchs, on fair face of brick work or concrete surfaces with surface finish even and smooth complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:3, on concrete surfaces on ceiling complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and diredcted.

M&L for prepration of new plastered surface of wall and applying two coat of exterior emulsion paint (Blue colour) on wall strip over one coat of primer complete all as specified and directed.

M & L for preparing newly plastered or previously untreated wall surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M & L for preparation of new plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over one coat of primer complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M&L for prepration of surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efforescent salts and applying one coat of white wash on old decorated surfaces on ceiling compele all as specified and directed.

M & L for preparation of old surfaces including brooming down to remove all dust, dirt and loose scales of item and other foreign matter or steel wire brushing scrapping down smoke soot, grease spots moulds moss and efforescent salts and trading oil and applying one coat of exterior emulsion paint (Blue) on wall strip complete all as specified and directed

M & L for preparation of old surfaces including brooming down to remove all dust, dirt and loose scales of item and other foreign matter or steel wire brushing scrapping down smoke soot, grease spots moulds moss and efforescent salts and trading oil and applying two coat of cement base paint on wall all as specified and directed

M & L for preparation of old surfaces including brooming down to remove all dust, dirt and loose scales of item and other foreign matter or steel wire brushing scrapping down smoke soot,grease spots moulds moss and efforescent salts and trading oil and applying one coat of oil bound distemper on wall all as specified and directed

M & L for preparation of old surfaces including brooming down to remove all dust,dirt and loose scales of item and other foreign matter or steel wire brushing scrapping down smoke soot,grease spots moulds moss and efforescent salts and trading oil and applying one coat of white wash on wall all as specified and directed

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S & F factory made PVC door frame of size 50 x 47mm with a wall thickness of 5mm grid PVC sheet mitered at corner and pinned with two members 150mm long brackets of 15 x 15mm MS Square tube 19 gauge EPDM rubber gasket weathered sheet to be provided through the frame, door frame to be fixed to the wall suing MS screw of 65/100mm size complete as per manufacturer specification. Make :-Rajshree / Kumar Arch

S & F 30mm thick factory made solid panel PVC door shutter conforming as per IS-4020 made from MS tube of 19 Gauge thickness of size 19 x 19mm style and 15 x 15mm for rail covered with heat moulded PVC channel of 5mm thick and 75mm, 125mm, 125mm wide for top rail, lock rail and bottom rail on either side at 5mm thick 20mm wide cross PVC sheet of gap inserted for top rail and bottom rail, paneling of 5mm PVC sheet fitted in MS frame welded/sealed to the style at rail with 30mm wide, 5mm thick PVC sheet beading sides and jointed together with solvent cement adhesive etc including aluminimum mongry complete all as specified and directed by Engineer-in-Charge. Make :- Rajshree / Kumar Arch or equivalent make as approved by GE

S & F for factory made solid panel wood grain printed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of PVC sheet to be fitted in the MS tube frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing complete all as specified and directed. Make :- Rajshree/Kumar Arch or equivalent make as approved by GE

M & L for 2nd class hard wood (SAL) plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for IInd class hard wood (SAL) plain framed, panelled factory made shutter 35mm thick (two panel 12 mm thick BWP) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial venneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M & L for glazed and skeleton 35mm factory made shutters 2nd class hard wood (SAL) , open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted withcut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified ad directed.

S&F Aluminium alloy, anodised, 300 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed complete all as secified and directed.

S & F 100mm long Stainless steel butt hinges, cold rolled MS, medium type,and fixed with stainless screw complete all as secified and directed.

S & F 75 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S & F for 125 mm extruded aluminum alloy classic handles, fabricated type., anodised fixed with stainless 04 nos screw complete all as secified and directed.

S&F for 150 mm aluminium, anodised, barrel tower bolts of extruded section and fixed with bright stainless steel bolt and fixed complete all as secified and directed.

S & F in repairs for 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F mild steel 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete all as secified and directed.

M&L for painting to new wooden surfaces of any description not otherwise described over 10cm wirdh or girth, with two coats of synthetic enamel paint (1st quality), over one coat of pink primer including preparation of surface complete all as secified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for providing 25 mm thick cement concrete (1:2:4) type B-O using 12.5 mm graded crushed stone aggregate as in floor etc surface finished even and fair complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes finished even and rough complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm (400 mm X 400 mm), as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. Make : Kazaria

M & L for vitrified ceramic light shade tiles 10 mm thick (Square or Rectangular) polished, area of each tile exc. 0.18 Sqm but not exc. 0.36 sqm (600 mm X 600mm) , as in floor etc. set and jointed of Make Kazaria or equivalent make as approved by GE and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for 10 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and fair complete all as specified and directed.

M & L for glazed ceramic coloured/printed tiles 600 mm X 300 mm X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. Make Kazaria or equivalent make as approved by GE

Taking down shutters from chowkhats, easing adjusting & refixing in same opening exc 1 Sqm and n exc 2 sqm each complete all as specified and directed.

S & F in-repair Oval type Vitreous china wash basin, snow white, flat back under counter type to be mounted on granite slab of size 560mm x 470mm x190 mm including cutting for and pinning in ends of the brackets complete all as specified and directed. Make :- Cera Cat Part No S2030104 or equivalent make and Cat Part of Parryware / Hindawre

S & F in-repair PVC low level flushing cistern first class white colour 10 Litres capacity, valve less, with inlet, ball valve, float and handle including brackets, PVC flush bend pipe complete all as specified and directed. Make(Brand): Parryware E8110 or equivalent make as approved by GE

S & F in repairs; Angle valves 15mm dia of pipe in cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed but fancy type chromium plated with long shank and cup complete all as specified and directed. Make : Jaquar , Cat no QQT-CHR-7053 or equivalent make as approved by GE

S & F in repairs; 15 mm dia PVC connection 45 cm long with two nuts and washers complete all as specified and directed. Make: Prayag /R S Industries

S & F in repairs; bib taps, chromium plated with fancy head with or without littered “Hot” or “Cold” screwed down, screwed for iron pipe of 15mm bore dia fancy type complete. Make Jaquar Cat No: QQT-CHR-7037 or equivalent make as approved by GE

S & F in repair 15 mm size bib tap standard of PTMT, any colour high pressure screwed for iron pipes (minimum weight 90 gram) complete all as specified and directed.

S & F for stainless steel AISI 304, Grating doom 100mm dia complete all as specified and directed

S & F in repair brass chromium plated shower rose 125mm size with swivel joint including a shower arm 15mm size, 195mm long with bend of 45 degree with flange of stainless steel . (Minimum weight 40 gms) complete all as specified and directed. Make :- Jaquar Cat Part No: OHS-CHR-1989, Arm Cat Part No SHA-CHR-475L100 or equivalent make as approved by GE

S & F for tubular towel rail 20mm dia D type 60cm long between flanges brass chromium plated complete fixed to walls complete all asspecified and directed. Make Jaquar, Cat Part No : AQN-CHR-7711 or equivalent make as approved by GE

S & F for towel ring of CP fixed with and including Chromium plated brass screws and wooden /plastic cleats (Minimum weight 190 gms) complete all as specified and directed Make : Jaquar Cat Part No.: ACN-CHR-1121BN or equivalent make as approved by GE

Demolition of Stone Laid, bedded and pointed in any mortar sett paving of any description of thickness complete all as specified and directed.

M&L for providing 18-20mm thick Z- black granite stone slab including sandwich type (IInd layer of 20mm at front) (table rubbed and polished) bull nosed as on shelves / cooking / steps / plateform / pillars over screed bed 20mm thick in CM 1:4 set jointed in neat cement slurry and pointed in white / coloured cement to match the shade complete all as specified and directed.

M&L for providing 18 mm thick single peace black granite stone slab (table rubbed and polished) bull nosed as in steps, jambs, pillars, window cills, cooking plateforms and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade of granite including rounding exposed edges and making hole for gas pipe complete all as specified and directed.

M & L for providing 18-20mm thick Z- Black black granite stone slab incl (table rubbed and polished) machine cut in skirting/dado laid 10mm plaster and jointed witht grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of type complete all as specified and directed.

M & L for providing 20mm thick marble white makrana machine cut, bedded jointed and pointed with grey cemeent slurry including cutting and polishing typesbull nosed as on shelves/window cill/pillars over screed bed 20mm thick in cm (1:4) set jointed in neat cement slurry and pointed in white/coloured cement to match the shade complete all as specified and directed.

S&F for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1016mm x 508mmx203mmincl bowl complete all as specified and directed . Make: Parryware, Cat Part No : C853099 or equivalent make as approved by GE

S & F stainless steel plate rack made out of 1mm thick steel sheet of size 75cm x 90cm x 25cm (minimum weight 3.5 Kg) with fixing arrangement complete as per sample kept in GE`s Office suitable for officers quarters complete all as specified and as directed. Make : Blue Star / Nirali or equivalent make as approved by GE

S&F in repair for 12 mm thick pre-laminated particle board, interior grade, pre-laminated one side with decorative choice lamination and other side balancing white lamination and fixed with screws to timber framework complete all as specified and directed.

S&F in repair for 18/19 mm thick pre-laminated particle board, interior grade, pre-laminated one side with decorative choice lamination and other side balancing white lamination and fixed with screws to timber framework complete all as specified and directed.

S& F in repair for 12 mm thick block boards, ex t e r i o r grade with decorative choice lamination on both side for cup boards, lockers, cabinets etc with necessary anchoring complete all as specified and directed.

M & L for 2nd class hard wood (SAL) moulding as in cornices, picture rails and the like, sectional area not exc. 6 sqcm complete all as specified and directed.

M&L 0.90 mm thick sunmica decorative laminate type 1 of surface finish colour and pattern as approved fixed with adhesive as per manufacturer instruction complete all as specified and directed.

S&F in repair 18/19mm Particle board, medium density, flat pre-ssed, single layer type or three layer type with BWR typee adhesive,fixed with screws to timber frame work complete all as specified and directed.

S & F 100 mm size aluminium anodised hasp and staple safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 150mm long Aluminium handles, cast type, anodised complete all as specified and directed

M&L 140mm length of Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor, complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F 30 mm wide flap when open, mild steel bright finish or electro galvanised continuous (Piano) hinge complete all as specified and directed.

S & F in repairs; stop valves fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed but fancy type chromium plated with long shank and cup (concealed type) (Bore dia of pipe in 15mm) complete all as specifed and directed. Make : Jaquar or equivalent make as approved by GE

S&F 100mm long (Width of recess between flanges (when open)) Parliament hinges, aluminium alloy anodised complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F 3mm thick Sheet frosted glass, ordinary quality and glazing withoil putty in square in n exc 0.5 sq.m in each pane complete all as specified and directed.

Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Drilling holes for cooking plateform in granite stone slab for gas pipe etc n. exc 25mm dia complete all as specified and directed

S&F in repairs for CP mixer for mixing for kitchen sink (Sink Mixer with Regular Swinging Spout (Wall Mounted Model) with Connecting Legs & wall Flanges), hot & cold water, screwed down for iron pipe and fixed complete all as specified and directed. Make : Jaguar Cat Part No. QQT-7309 of Queen's series or or equivalent make as approved by GE

S&F in repairs for CP mixer 2 in1 for mixing for WHB (Central Hole Basin Mixer with regular Spout without Popup waste System with 450 mm Long Braided Hoses), hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. Make : Jaguar Cat Part No. QQT-7167B of Queen's series or equivalent make as approved by GE

S&F CP brass wall mixure three in one with hand shower with accessories with mark Hot and Cold complete all as specified and directed Make : Jaquar, Cat Part No. QQT-CHR-7273UPR or equivalent make as approved by GE

S&F for Toilet paper holder chromimun plated as approved quality complete all as specified and directed Make : Jaquar, Cat Part No. AHS-CHR-1551 or equivalent make as approved by GE

S&F for corner glass self, fancy type with 5.50mm thick glass mounted on CP brass frame fixed with brass screw & plug as suitable for bath room as per manufacturer instruction complete all as specified and directed. Make : Jaquar Cat Part No. ACN-WHM-1173 or equivalent make as approved by GE

S & F in repairs Chromium plated health faucet with hand shower & flexible cord suitable for EWC including fixing to steel pipe or union complete all as specified and directed. Make : Jaquar, Cat Part No. ALD-CHR-563 or equivalent make as approved by GE

Supply and fixing fancy type soap dish, chromium plated complete all as specified and directed. Make : Jaquar Cat Parft No. ACN-CHR-1131N or equivalent make as approved by GE

S&F in repair 5.50 mm thick swivel type looking mirror 630x445 mm size of approved quality fixed to walls with suitable stain less steel brackets and screws complete all as specified and directed. Make : Jaquar Cat Part No. AKP-CHR-35795 or equivalent make as approved by GE

M&L stainless steel mirror polished exterior grade 304, SS, vertical / horizontal square / round pipe and top cap for stair case railing all as specified and directed.

S&F in repair 25 mm dia Stainless steel curtain rod with fixing brackets , stops , side fancy rollers set as slected by GE complete all as specified and directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

S&F SS sliding double channel for drawer up to 300 mm long all as approved by GE complete all as specified and directed. Make : Hettich / Ozone / Sleek

Demolition of brick work or stone / boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed.

Excavation over areas not exc. 1.50 m deep and getting out in Soft / loose soil complete all as specified and directed.

Excavation over areas exc. 1.50 m but n exc 3.0 m deep and getting out in Soft / loose soil complete all as specified and directed.

M & L for providing plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for brick work with fly ash bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with fly ash bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M & L for brick work with fly ash bricks, straight or curved on plan and any radius in honey combing wall built in cement mortar 1:4 complete all as specified and directed.

M & L for providing plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M & L for providing plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

S & F 20 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

Taking down and Re-fixing of 20 mm bore old steel water tubing and connection in new or old position (wall, ceiling, floors etc) including cleaning of old pipes and provision of new GI fittings as required complete all as specified and directed.

S & F in repairs vitreous china wash basin white, flat back, size 550 X 400 mm excluding taps, waste, chain and plug and porcelain washer but including CP waste coupling,PVC waste pipe & brackets, cutting for and pinning in as required complete all as specified and directed.

S & F in repairs PVC low level flushing cistern, white, 10 litre capacity, valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, flush pipe, brass screws, handle etc complete having with and including brackets, 32 mm bore PVC flush pipe of suitable length complete all as specified and directed. Make (Brand) : Commander (Champion) / Cera (Ceina) / Parryware (Sleek)

S & F in repairs 15 mm bore, long body, chromium plated, fancy type bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15 mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shank and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F tubular towel ring 30cm dia flanges brass chromium plated complete fixed to walls complete all as specified and directed.

S&Fin rep 5.50 mm thick looking mirror 600x450 mm size of approved quality fixed to walls with suitable stain less steel brackets and screws complete all as specified and directed.

M & for Sub base, 100mm thick with broken boulders or quarried stone, interstices filled, surface formed and rolled and consolidated to required gradient and camber complete all asspecified and directed.

M & L for providing 75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M & L for providing 100 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacer and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded crushed stone aggregate, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like complete all as specified and directed.

M & L for providing reinforced cement concrete 1:1.5:3 type A-1, using 20 mm graded crushed stone aggregate, as in chajjas complete all as specified and directed.

M & L for form work to chullah hoods, chajjas, troughs and similar items including edges in fair finished surface of concrete complete all as specified and directed.

M & L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200 mm thick horizontal or slopping in fair finished surface of concrete complete all as specified and directed.

S & F water closet vitreous china squatting pan ‘Orissa’ pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern) including CI 'P' or 'S' trap and PVC flush pipe, connection to trap and flushing pipe, anti-syphonic pipe etc. including lean concrete as required complete all as specified and directed.

S & F in repair Vitreous china urinal (back or corner wall type), including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed. Make :- Hindware /Parryware or equivalent make as approved by GE

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

M & L for 50 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in sub floor of floor finishes, finished even and rough complete all as specified and directed.

Forming construction joints 30 mm deep x 10mm wide filled with ceiling compound Gd 'A' complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M & L for cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M & L for 150 mm bore salt glazed stoneware drain pipes grade 'A' laid in trenches and jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs for manholes, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded crushed stone aggregate and setting in cement mortar 1:6 including necessary form work complete all as specified and directed.

M & L for broken bricks aggregate for loose filling, of gauge 40 mm to 80 mm graded in soakage pits, soakage wells complete all as specified and directed.

S&F for powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. with powder Coating (minimum thickness of powder coating 50 micron) complete all as specified and directed.

Providing & Fixing of Armstrong Mineral Fibre Acoustical Suspended Ceiling System with ANF Angled Tegular edge tiles with Armstrong Prelude 24mm exposed grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.5, Light Reflectance ≥85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 15mm, suitable for Green Building application, with Recycled content of 30%. The tile shall be laid on Armstrong Prelude 32 with 24 mm wide T-section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 32mm and a load carrying capacity of 8.5 Kgs/Sqm (as per standard installation layout mentioned below) & pull out strength of minimum 100 Kgs. The T-Sections have a Galvanizing of 90 grams per Sqm and need to be installed with Suspension system of Armstrong make. INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using Armstrong suspension system (specifications below) at 1200mm maximum. The First/Last Armstrong suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be Armstrong wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum.

ARMSTRONG SUSPENSION SYSTEM accessories manufactured and supplied by Armstrong World Industries consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum pull strength of 110 kgs. (Adjustable hook clips of 0.7mm thick, galvanized spring steel can also be used for installation purpose as an additional accessory. The adjustable clip also consists of a 4 mm aquiline wire to be used with the main runner). Note :- Installation to be carried out by Armstrong Trained Installation team & Installation should be carried out as per Armstrong recommended procedure.

S & F for powder coated anodised aluminium window and ventilator shutters with powder Coating (minimum thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S & F for powder coated anodised aluminium door shutters (minimum thickness of powder coating not less than 50 micron), aluminium section weighing 0.55 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, hydraulic door closer /floor door spring, anodised aluminum snap beading screws etc. including all fittings complete all as specified and directed.

S & F 2nd class hard wood (SAL) plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails sectional area not exc. 3 Sqcm complete all as specified and directed.

S & F in repairs mild steel PVC design coated Harrison rails, with fixing brackets, stops, rollers side fancy balls etc. complete all as specified and directed.

Taking down carefully Aluminium/ Copper point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling roses, pendants, lamp holder, regulator, switch socket outlet, light fittings, shade conical etc and separating serviceable fittings & fixtures for re-use in the work as directed including removing of unserviceable fittings & fixtures with wiring cable, existing conduits etc from site and making good disturbed surfaces of walls, floors, ceiling etc complete all as specified and as directed.

Drawing out old sub main copper / aluminium cable off various sizes from existing conduit/ batten complete all as specified and directed.

Taking down old MCB DB all type including MCBs complete all as specified and directed.

M&L for point wiring complete with FRLS multi- stranded copper conductor 2 x 1.5 Sqmm size PVC insulated unsheathed cable 1100 Volt grade, conforming to IS-694 and in conduit system of wiring, drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings/ fixing accessories on wall and on existing conduit of ceiling and including modular, metal flush box of required module including cover frame and plate for mounting / fixing of modular switch/socket/ fan regulator as required and including single core stranded conductor copper 1.5 Sqmm size PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same conduit and making good disturbed surface complete all as specified and as directed for the following :- Make of cable : Finolex, L&T, RR Kable

(a) One light point controlled by one way switch, modular type.

(b) One Fan point controlled by one way switch, modular type.

(c) One 3 pin socket outlet, 5/6 amps, on independent board, modular type.

(d) One 3 pin socket outlet, 5/6 amps, on same board, modular type.

(e) One light point, controlled by 2-way switch, modular type.

M&L for point wiring complete with FRLS multi- stranded copper conductor 2 x 2.5 Sqmm size, for 16 Amps socket outlet on independent board, PVC insulated unsheathed cable 1100 Volt grade, conforming to IS-694 & colour code in conduit system of wiring, drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25mm dia ISI marked ivory colour with all conduit fittings/ fixing accessories on wall and on existing conduit of ceiling and including Modular, metal flush box of required module including cover frame and plate for mounting / fixing of modular switch/socket as required and including single core stranded conductor copper 2.5 Sqmm size PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same conduit and making good disturbed surface complete all as specified and as directed. Make of cable : Finolex, L&T, RR Kable. Note for BOQ Item No 164 & 165 Cost of cutting/ chasing for conduits and making good disturbed surface deemed to be included in unit rate.

S & F Wall/surface mounted type LED light fitting batten type complete with LED lamp 1x 20/22 watt, PF > 0.9, lumen output 2000 lumen , extruded aluminium complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable complete all as specified and directed. Make Philips Cat No BN 021C LED 20S PSU CW GR S2 or Wipro Cat Part No LL20-221-XXX-65NE3 or equivalent make of Osram.

S&F wall/ surface mounted 10 Watt LED Batten, Mirror light, extruded aluminium housing provided due efficient heat dissipation with polycarbonate diffuser and integrated driver complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable complete all as specified and directed. Make :- Philips Cat Part No BN 021C LED 10S 6500 PSU GR S1, Havells Cat Part No ENDURA LINEAR NEO BS 10W LED 830PCWH/ or equivalent Cat Part No of Crompton as approved by GE

S&F LED Bldg light fitting 20 Watt, status High lumen output cast aluminium alloy toughned glass, IP65 and wired with all accessories complete with GI bracket made out of 25mm bore GI tubing med grade 1.2 Mtr length and bend to shape for fixing bldg security light and making connection by using three core flexible twisted copper wire of 23/0.0076 etc. complete all as specified and directed. Make Philips Cat Part No BRP 022 LED 20 CW MR S1 PSU GR or Wipro Cat Part No LR02-331-XXX-57-XX or equivalent make of Osram.

S&F LED retrofit Lamp 12 Watt complete all as specified and directed. Make :- Philips/Wipro/Osram.

Taking down Ceiling fans, cleaning, oiling and greasing, including painting with one coat of synthetic enamel paint approved colour after cleaning & preparing the surface and re-fixing at the existing site/rooms and connected with 23/0.0076 three core PVC flexible cable from ceiling rose to C/Fan etc complete all as specified and directed.

Taking down and dismantling Geyser of any make and Capacity for descaling, welding / brazing of detecting the leakage, replacing and refixing the same after making it funcional including replacement of worn out nuts, bolts, washers etc complete all as specified and directed. Note :- The T&P and material cost required etc are to be included in the quoted rates.

Supply and fixing in replacement of the old unserviceable worn out / plastic Exhaust Fan with new exhaust fan of 300 mm sweep metalic body (Heavy duty) single phase 230/240 volts, AC, 900 RPM complete and making holes with lovoured shutters including mounting frame and connecting the fan to ceiling rose including provision of three core flexible copper conductor cable of size 1.5 sqmm copper including to inside out surface & white wash etc with not less than 0.5mtr long to connection complete incl taking down old U/S Exhaust fan complete all as specified and directed. Make :- Orient Model No - Orient 300mm or 12" H.D EX Fan/ Equivalent of Usha, Almonard. Note :- Unserviceable Exhaust Fan will be deposited in MES Store yard.

S&F Modular Fan Step Regulator 120W, 2 Module 230 volts complete all as specified and directed. Make- Legrand (Arteor), Schneider (Zencelo), Hager (Berker)

S&F Single pole and neutral enclosure with a two pin and earth plug and socket, complete with a single pole MCB 20 Amps modular type complete in sheet metal enclosure complete all as specified and directed. Make :- Legrand, Schneider, Hager

S&F Modular switch 6 amps, one way, one module complete all as specified and directed. Make- Legrand (Arteor), Schneider (Zencelo), Hager (Berker)

S&F Modular socket outlet 6 amps, 2/3 pin, combined 2 module complete all as specified and directed. Make- Legrand (Arteor), Schneider (Zencelo), Hager (Berker)

S&F Modular angle holder insulated body with back plate for batten fittings all as specified and directed. Make :- Legrand, Schneider, Hager

S&F ceiling rose, surface bakelite,65 x 50mm, three terminals all as specified and directed. Make :- Legrand, Schneider, Hager

S&F Modular socket outlet 6 and 16 Amps, 2/3 pin combined 2 module complete all as specified and directed. Make- Legrand (Arteor), Schneider (Zencelo), Hager (Berker)

S&F Modular switch one way,16 Amps, complete all as specified and directed. Make- Legrand (Arteor), Schneider (Zencelo), Hager (Berker)

S&F Modular type switch two way, 6 Amps, one module complete all as specified and directed. Make- Legrand (Arteor), Schneider (Zencelo), Hager (Berker)

M&L for submain wiring with two run of single core PVC insulated unsheathed multi stranded copper conductor FRLS cable of size 4 Sqmm 1100 Volts grade and one run of PVC insulated unsheathed stranded copper conductor FRLS cable of size 4.0 Sqmm 1100 Volts grade as earth continuity conductor drawn through in and including rigid non metallic PVC conduit of size 25mm dia concealed including making good the disturbed surfaces of wall etc including complete all as pecified and directed. Note :- Cutting/ chasing for conduits shall be measured and paid separately.

M&L for submain wiring with two run of single core PVC insulated unsheathed multi stranded copper conductor FRLS cable of size 6 Sqmm 1100 Volts grade and one run of PVC insulated unsheathed stranded copper conductor FRLS cable of size 6 Sqmm 1100 Volts grade as earth continuity conductor drawn through in and including rigid non metallec PVC conduit of size 25mm dia concealed including making good the disturbed surfaces of wall etc including complete all as directed. Note :- Cutting/ chasing for conduits shall be measured and paid separately.

Supply and Fix flush mounting factory made SPN DBs Double door , IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar and cables ties for cable management fully insulated bus bar 8 way with 200 Amps rated bus bar complete all as specified and directed. Make :- Legrand, Schneider, Siemens

S&F MCB SPN (single pole and neutral), 240 volts, 40 Amps breaking capacity 10 KA, ‘C’ Series. etc , complete all as specified and directed. Make :- Legrand, Schneider, Siemens

S&F MCB SP (single pole) 240 volts, 6 - 32 Amps, 50HZ, 10 KA. , ‘C’ series complete all as specified and directed. Make :- Legrand, Schneider, Siemens

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but not exc 20 cm girth complete all as specified and as directed.

Zaigham Enterprises

M/s M Aali construction co

MAYA CONSTRUCTION

MOHINDER SINGH AND SONS

Builders Harpal