Addn / Altn to VIP Block, VVIP Cottage and New(SIB) Building at DRDO Transit Facility Sagardeep, Chandipur

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5sq.m and under, including cutting the patch in proper shape, racking out joints and prepairing and plastering the surface of the walls complete,including disposal of rubbish to the dumping ground within 50mtrs lead :With cement mortar 1:1(1Cement : 4Coarse sand)

Brick Work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in cement Mortar 1:4 ( 1 cement : 4 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the...

... help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) .

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Finishing with Deluxe Multi surface paint system for interiors using Primer as per manufacturers specifications : Two or more coats applied on walls @1.25ltr/ 10Sqm over and including one coat of special primer applied @ 0.75ltr / 10Sqm)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg / 10Sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture . (On Steel Surface)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture . (On Wooden Surface)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50meters lead . For thickness of tiles 10mm to 25mm.

Demolishing cement concrete manually / by mechanical means including disposal of material within 50mtrs lead as per direction of Engineer-in-charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm dia metre holes with chlorpyriphos /Lindane E.C. 20% with 1% concentration.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size. Size of Tile 600 x 1200 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50mtrs lead : Of area beyond 3 sq mtrs

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing ISI marked Flush door shutters conforming to IS : 2202 (Part - I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws .

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters. With ISI marked stainless steel butt hinges of required size Second class teak wood .

Providing and fixing in wall lining flat pressed three layer (medium density) particle board including priming coat on unexposed surface, with necessary fixing arrangement and screws etc, complete. 12mm thick

Providing and Fixing decorative high pressure laminated sheet of plain / wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality including cost of adhesive of approved quality. 1.5mm thick

French Spirit polishing:Two or more coats on new works including a coat of wood filler.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : Rectangular shape 1500x450mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo embossed on the body door weight upto 35kg and door width upto 700mm), with necessary accessories and screws etc complete.

Providing and fixing bright finished brass tower bolts with necessary screws etc. complete. 250x10mm

Providing and fixing bright finished brass handles with screws etc. complete 125mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete 100mm

Providing and fixing bright finished brass tower bolts with necessary screws etc. complete. 150x10mm

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc.complete. Size 75mm

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top and bottom pivot and spring type fixing arrangement and making necessary holes etc. for fixing required door fittings all complete as per direction of Engineer-in-charge. (Door handle, lock and stopper etc to be paid separately).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge . With stainless steel cover plate minimum 1.25mm thickness.

Providing and fixing aluminium tubular handle bar 32mm outer dia, 3.0mm thick & 2100mm long with SS screws etc complete as per direction of Engineer-in-Charge. Polyster powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868,minimum anodic coating of grade AC 15).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, including welding, grinding, buffing, polishing and making fitting the same with necessary accessories & stainless steel nuts and bolts complete of required size as per direction of Engineer-in-charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge. (a) Internal Work- Exposed on wall

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipes with clamps 1.00m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Internal work - Exposed on wall, 25mm nominal outer dia pipes.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc, the tiles must be cut with the zero chipping diamond cutter only . Laying tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. ofcomplete. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid .

Providing and fixing white Rimless Single Piece WC with UF Soft Closet Seat Cover, Hinges, Dual flush Cistern Fitting, Fixing Accessories Set, Size : 360x675x750mm S Trap - 300mm complete as per the direction of Engineer-in-Charge. Make : Jaquar, Model No. OPS-WHT-15853S300UF.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.

Providing and fixing table top wash basin with all necessary fittings complete as per the direction of Engineer - in- Charge. Size : 495x395x150mm, Shape - Rectangular, Make ; Jaquar Model No. JDS-WHT-25909.

Providing and fixing CP Single Lever Basin Mixer with 450mm long Braided Hoses Make : Jaquar Model No. OPP-CHR-15011BPM as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality and make as approved by Engineer - in - Charge. 15mm nominal bore

Providing and fixing CP Hand Shower @ 95mm round shape single flow with rubbit cleaning system Make : Jaquar Model No. HSH-CHR-1653 as per the direction of Engineer-in-charge.

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make as per the direction of Engineer-in-charge

Providing and fixing CP Rain Overhead Shower @ 150mm round shape single flow with self cleaning function Make : Jaquar Model No. OHS-CHR-1801 as per the direction of Engineer-in-charge

Providing and fixing CP Shower Arm @ 20mm & 600mm Long round shape with 90° bend for wall mounted showers with flange Make : Jaquar Model No. SHA-CHR-479L600 as per the direction of Engineer-in-charge

Providing and fixing CP Two Way Bib Cock with Wall Flange Make : Jaquar Model No. ARI-CHR-39041 as per the direction of Engineer-in-charge

Providing and fixing CP Health Faucet with 8mm dia 1.2 Meter Long Flexible Tube and Wall Hook Make : Jaquar Model No. ALD-CHR-573 as per the direction of Engineer-in-charge.

Providing and fixing CP Towel Rack with Lower Hanger (SS) with Hook Make : Jaquar Model No. AHS-CHR-1581H as per the direction of Engineer-in-charge.

Providing and fixing CP Towel Ring Round with Round flange Make : Jaquar Model No. ACN-CHR-1121BN as per the direction of Engineer-in-charge.

Providing and fixing CP Coat Hook (SS) Make : Jaquar Model No. AKP-SSF-35761P as per the direction of Engineer-in-charge.

Providing and fixing Soap Disc Holder Make : Jaquar Model No. ACN-CHR-1131N as per the direction of Engineer-in-charge.

Providing and fixing Liquid Soap Dispencer wih glass bottle Make : Jaquar Model No. ACN-CHR-1135N as per the direction of Engineer-in-charge.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Earth work in excavation by mechanical means(Hydraulic Excavator / manual means over areas (exceeding 30cm in depth, 1.5in width as well as 10sqm on plan) including disposal of excavated earth lead upto 50mtr and lift upto 1.5mtr, disposed earth to be levelled and neatly dressed. Ordinary Rock

Supply and filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level : 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size

Centering and shuttering including strutting, propping etc,and removal of form for : Suspended floors, roofs and access platform

Steel Reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated Bars

Providing and laying position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level : 1:1.5:3 (1Cement : 1.5 Coarse sand : 3 Graded Stone aggregate 20mm nominal size)

Steel work in built up tubular (Round,Square or Rectangular hollow Tubes) Trusses etc. Including Cutting, hoisting, fixing in position and applying a Priming coat of approved Steel Primer, Including Welding and bolted with special shaped washers etc. Complete. Electric Resistance or Induction Butt welded Tubes.

Providing Corrugated GS sheet roofing including vertical / curved surfrace fixed with polymer coated J or L hooks, bolts and nuts and all necessary fittings complete.1.00 mm thick with zinc coating not less than 275 gm/m2

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete. Black Zebra.

Making Plinth Protection 50mm thick of cement concrete 1:3:6(1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Providing and fixing LED Round 205mm Panel CDL 18Watt Make : Crompton Model No. LSDRMN-18W-CDL/NW/WW

Providing and fixing LED Round 185mm Panel CDL 15Watt Make : Crompton Model No. LSDRMN-15W-CDL/NW/WW

Providing and fixing LED Round 62mm Down Light 3Watt Make : Crompton Model No. LDRDTC-3W-CDL/WW

Providing and fixing LED Round 36mm Spot Light 2 Watt Make : Crompton Model No. LDSPR2-WW

Providing and fixing LED Strip (5m Long) Light Warm White 20 Watt Make : Crompton Model No. LSTGL20-WW

Providing and fixing LED Batten Light CDL 4' 20 Watt Make : Crompton Model No. LDSLRP20-CDL

Providing and fixing LED Batten Light CDL 2' 10 Watt Make : Crompton Model No. LDLL10-CDL

Providing and fixing LED Surface mounted Round 140mm Down Light 12 Watt Make : Crompton Model No. LSDSSV-12W-CDL

Providing and fixing decoraive window blind as per the direction of Engineer-in-Charge

SCHEDULE OF CREDIT

Doors frame & shutter

Scrap Brass

Scrap iron

Old WC s Orissa / EWC

GI pipe 15 to 40mm

RANA ENTERPRISES

PTS ASSOCIATES

LIRA CONSTRUCTIONS PVT LTD

M/s New Weather

M/s B K SERVICES

M/s HARIOM ENTERPRISES

CHARAN ELECTRICALS

PMR CONSTRUCTIONS