PROVN OF NON LOAD BEARING HARD STANDING AT 29 END, CONSTN OF PARKING SHED NEAR ALTERNATE ATC, PROVN OF FIRE EXIT FOR MAIN ATC, PROVN OF CCD PAINTING IN CERTAIN BUILDINGS AND PROVN OF CERTAIN B/R REVENUE AND MINOR WORKS IN AF STATATION BAREILLY.

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 1.50 Kilometre but not exc. 5.00 Kilometre and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for providing cement concrete 1:1.5:3 type A-1, using 20 mm graded stone aggregate as in pavements, hard standing and the like finished even and fair without using extra cement, in any thickness as directed by the Engineer-in-Charge with and including necessary form work for lateral support complete all as specified and directed.

M & L for cutting of PCC with diamond cutter and making groove of 5 to 12 mm wide in tarmac to a depth of 35 mm, cleaning the joints by means of compressed air and fill the joints by mechanical means as per following process: - (i) Provision of backup rod of suitable dia to be inserted in the joint tightly as specified. (ii) Provision of adequate masking tape on either sides of joint to avoid spillage on concrete surface before applying joint sealant and removing the same after sealing of joints. (iii) Supply and filling of sealing compound properly for a depth of not less than 10 mm for joints upto 32 mm wide after application of suitable primer as directed by Engineer-in-Charge. (The finished level of sealed joints shall be on an average 3 mm below the top surface of slabs.)

All as per item No. 5.00 hereinbefore but making groove of 12 to 18 mm wide in tarmac to a depth of 35 mm complete all as specified and directed. NOTE FOR ITEM NO. 5.00 AND 6.00: - Sealing compound shall be Bostik "Seal N flex -2k', 02 component (Base and Hardner) Bostik Polyurethane sealent of grey colour conforming to BS-5212 with minimum movement accommodation factor of + 30% when tested as per ASTM C-719 or equivalent product of M/S Choksey Chemicals Pvt. Ltd. or M/S STP Ltd. as approved. The sealent shall have shore A @ 25 degree centigrade =15 + 5 and as per manufacturer's instructions.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out in pavement quality concrete (PQC) and removing surplus demolished material to a distance not exc. 50 m and making good disturbed surface complete all as specified and directed.

M & L for providing plain cement concrete, type B-2, 1:2:4 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade St-240 complete all as specified and directed.

S & F of flat iron bands, straps, supports, clamps, hold fasts, wall ties, hooks for hanging fans and other similar small steel article confirming to Fe-290 Grade E-165 with and including necessary nut-bolts, washers, screws etc. as required complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S & F of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based metal profile steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe-290 Grade E-165 complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M & L for brick work with fly-ash old size bricks having designation 75 conforming to IS-12894 (2002), straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

S & F of collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed.

Cutting holes in RCC column / pillar for inserting hold fasts for a depth of exc. 56 mm but not exc. 112 mm from jamb and making good dismantled portion in cement concrete 1:2:4 type B-1 complete all as specified and directed.

M & L for cutting grooves in floor, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and fair complete all as specified and directed.

M & L for preparation of newly plastered previously untreated surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

M & L for preparation of old decorated surfaces of walls and applying one coat of distemper oil emulsion over a thin coat (average 1 mm thick) of wall care putty complete all as specified and directed.

M & L for providing 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm grade stone aggregate) as in sub floor, sub base of floor finished even and rough complete all as specified and directed.

M & L for heavy duty anti skid exterior floor tiles make Johnson Endura or Kajaria of size 300 X 300 X 10 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floors complete all as specified and directed.

M & L for rubber moulded glossy finish coloured pre-cast cement concrete chequered tiles with grey cement and pigment, size 300 mm X 300 mm X 25 mm thick as in floors, set, jointed in neat cement slurry and pointed in neat cement slurry mixed with pigment to match the shade of tile complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished even and rough complete all as specified and directed.

S & F of high intensity prismatic Retro reflective sheeting of make 3M or other ISI make as approved by GE, fixed in existing iron sheet of red colour complete all as specified and directed.

S & F of aluminum section powder coated of approved colour as in door frame and shutter partially glazed with 5.5 mm thick one side refelctive glass and partially panelled, panel made of 5 mm thick PVC composite board duly fixed with aluminium clips of suitable size comprising of the following complete as specified and directed: - (i) Frame made of section size 100 X 40 X 2 mm thick. (ii) Styles of shutter made of section size 85 X 44.45 X 1.70 mm thick. (iii) Top rail and bottom rail made of section size 114.30 X 44.45 X 1.7 mm thick. (iv) Middle rail made of section size 83.50 X 44.75 X 1.7 mm thick. (v) Glazing clip 0.7 mm thick of appropriate size. (vi) 2 Nos. stainless steel Handle 300 mm long as approved. (vii) Tower bolt having dia of bolt 9.90 mm dia and 200 mm long. (viii) Mortice lock 100 mm size, 7 Livers make Godrej. (ix) Hold fast aluminium 100 mm long. (x) Rubber gasket made of virgin white PVC and namda rope of appropriate size for proper air tightness.

M & L for providing reinforced cement concrete 1:2:4 (Nominal Mix) type B-1, using 20 mm graded stone aggregate, as in beams, cantilevers, bressummers, lintels over 1.50 m span and the like complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified and directed.

M & L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M & L for repairing of broken edges of chhajja, roof projection and the like at any height by providing cement concrete 1:2:4 type B-1 where ever required and finally plastering the complete repaired edges with 10 mm thick cement plaster in cement mortar 1:3 and finished the surface smooth and even without using extra cement to match the adjacent old surface complete all as specified and directed. NOTE: - The unit rate as quoted for this item shall deemed to included the cost of formwork and scaffolding as required.

M & L for re-writing or painting letters or figures (Block, Roman, Italic or Indian) not exc. 30 cm high with synthetic enamel paint complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and fair complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for providing 100 mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm grade stone aggregate) as in sub floor, sub base of floor finished even and rough complete all as specified and directed.

S & F of aluminium anodised powder coated of approved colour, sliding type 02 track (01 glazed and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick tinted glass and mosquito proofing net as detailed below complete all as specified and directed: - (i) Frame section 61.85 X 31.75 X 1.20 mm for top, bottom and sides rails weight not less than 0.659 Kg per Sqm. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.50 mm. (iii) Glass 4.80 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips with and including necessary handles, tower bolt etc. as directed. (iv) Aluminium grill powder coated not less than 1.00 Kg per Sqm duly fixed with aluminium section 20 X 10 X 1.5 mm size. (v) Stainless steel wire cloth. (vi) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vii) Locking arrangement and providing Namda rope to make the frames air tight.

M & L for vitrified ceramic dark shade polished coloured tiles 10 mm thick (Square or Rectangular) area of each tile not exc. 0.36 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

S & F Fine fissured board of size 595 X 595 X 15 mm thick mineral fibre accoustic false ceiling tiles with and including false ceiling grid system at any height with back of the ceiling duly sanded and finished with a coat of protective paint and front duly finished and fixed to true lock PVC DLE KL-24 suspension system (hot dipped galvanised steel section) of exposed T-section grid with exposed face powder coated white colour including making good electric service such as point wiring etc. complete all as specified and directed. NOTE: - For detailed description and specificatios of ceiling grid and ceiling board refer Particular Specifications hereinafter. (CAT Part No. 1833 M of ARMSTRONG or as approved by GE in writing.)

M & L for mild steel deformed or twisted bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacer and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed.

M & L for vitrified ceramic dark shade double charged coloured tiles 10 mm thick (Square or Rectangular) area of each tile exc. 0.42 Sqm but not exc. 1.00 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

M & L for 19 / 20 mm thick block board grade 1 quality, exterior grade, commercial type fixed with screws to timber framework as in wall or kitchen cabinet complete all as specified and directed.

S & F of 0.90 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S & F of 30 mm wide flap when open, mild steel bright finish or electro galvanised continuous (Piano) hinge complete all as specified and directed.

S & F of drawer handle, brass, projected drop (50 mm to 65 mm) on screwed plate complete all as specified and directed.

S & F of 450 to 600 mm long heavy duty stainless steel telescopic channel with sliding over steel ball rollars auto lock type suitable for drawer of weight upto 5 Kg complete all as specified and directed.

M & L for point wiring for one light point / fan point / bell point / 5 Ampere socket outlet point (Independent point), controlled by one, one way switch with 1.50 sqmm size, PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable (FRLS) in colour coding as directed, drawn into and including PVC conduit medium grade (not less than 20 mm dia) with and including its all necessary fittings and accessories fixed on surface and making good as per existing and sunk cast iron or 1.2 mm thick pressed steel terminal boxes for mounting fittings like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size stranded copper conductor cable (FRLS) as in earth wire and connecting all metal parts to common earth dolly complete all as specified and directed.

All as per item No. 58.00 hereinbefore but wiring for one 3 / 6 pin 15 Ampere socket outlet point on independent board and wiring using with 2.50 sqmm size cables as on existing conduits complete all as specified and directed.

S & F of wall / surface mounted type LED light fitting batten type complete with and including LED lamp 1 X 20 watt (4 feet long), extruded aluminium heat sink provide for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including making electric connection with flexible twin core 1.00 sqmm size stranded copper conductor cable from light fitting to ceiling rose complete all as specified and directed. Make- Philips Cat. Part No. BN021C LED20S PSU CW GRS2 (Smart Bright) of Philips or ENDURALINEARNEOBS20WLED865SPCWH (ENDURA LINEAR NEO) of Havells.

Supply and fixing of LED security light fitting as per Cat. Part No. BRP022 LED 20 CW MR S1 PSU GR (GREENLINE SMART) of Philips or Cat. Part No. ENDURAPEARLSL25W LED757SASYTOPCMP (ENDURA PEARL 25 W MP) of Havells or Cat. Part No. LR06-311-XXX-57-XX 25 Watt of Wipro with and including security light bracket made of suitable dia GI pipe light grade not less than 0.65 metre length alongwith fixing arrangement complete all as specified and directed.

S & F of switch piano flush button single pole 230 volts, one-way 5 Ampere complete all as specified and directed.

S & F of switch piano flush button single pole 230 volts, one-way 15 Ampere complete all as specified and directed.

S & F of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC complete all as specified and directed.

S & F of flush mounting factory made Ekinoxe SPN DB's 8 way as per Cat. Part No. 607711 of Legrand or Cat. Part No. A9HSND08 of SCHNEIDER or Cat. Part No. CSDBSPNDD08 of C&S, Double door, IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed.

S & F of MCB single pole and neutral, 240 volts, 40 Ampere breaking capacity 10 KA, ‘C’ Series complete all as specified and directed.

S & F of MCB single pole 240 volts, 6 to 32 Ampere 50 Hz, 10 KA, ‘C’ series complete all as specified and directed.

Supply and laying in trenches / ducts, passing through pipe / fixing on poles 1100 volts grade, ISI marked, 10 Sqmm 2 core, LT cable (heavy duty), XLPE insulated served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and over all PVC sheathed with stranded aluminium conductor cable including commissioning and testing complete all as specified and directed.

S & F of 25 mm bore light grade galvanised iron tubing with all necessary GI fittings as in protection pipe of cable laid in trenches or fixed to pole or other vertical surface or for insertion in horizontal boring complete all as specified and directed.

M & L for laying of course sand free from sharp materials as in filling in trenches for cable protection, laid to a uniform thickness of 23 cm (15 cm under the cable and 8 cm over the cable) and gently punned down to 18 cm thickness as required complete all as specified and directed.

M & L for laying brick as in protection covers over cables using well brunt sub class 'B' old size bricks in trenches over sand cushioning complete all as specified and directed.

Supply and fixing of 1100 volts grade three single core 2.50 Sqmm size each, flexible multi-stranded copper conductor cable, PVC insulated and overall PVC sheathed round flexible connection wire as in electric connections complete all as specified and directed.

Supply and fixing of LED street light fitting as per Cat. Part No. BRP410 LED 091 CW HE MR PC S2 PSU GR (GREENLINE V2) of Philips or Cat. Part No. ENDURAPEARLMAGSL120WLED757PASYTOTGASTHO (PEARL MAGNUM) of Havells or Cat. Part No. LR02-132-XXX-57-G2 (SKYLINE LR02) of Wipro with and including street light bracket made of suitable dia GI pipe light grade not less than 0.65 metre length alongwith fixing arrangement complete all as specified and directed.

S & F of shock proof, rust proof, fire retardant non transparent Kiosk pole box of size 310 X 210 X 120 mm made of Engeineering plastic one piece moulding, for out door duty, with four Nos. of insulated aluminium bus bar of 60 Ampere capacity mounted on unbreakable insulators, 10 Ampere MCB SP with aluminium lugs of suitable size upto 50 Sqmm including 02 Nos. 40X3 mm flat iron clamps duly painted both side with two coats of synthetic enemel paint over a coat of red oxide primer, necessary suitable size nut-bolts, washers etc. complete all as specified and as directed.

MOHINDER SINGH AND SONS

S.M. KAZIM

M/S Quality Constructions

M/s M Aali construction co

VINYAK TRADERS

M/S KAYS ENTERPRISES