PROVISION OF AUDITORIUM CUM LECTURE HALL WITH SEATING CAPACITY OF 275 PERSONNEL AT COAST GUARD DHQ1 PORBANDAR SPL WORK

Amount

SCHEDULE "A" Part - I (BUILDING WORKS) Details of prepriced schedule is given in tender documents.

SCHEDULE "A" PART-II ( SITE CLEARANCE, EXCAVATION, & EARTHWORK) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-III (INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IV (INTERNAL ELECTRIC SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-V (ROAD/PATH/HARDSTANDING) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VI (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VII (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-VIII (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-IX (EXTERNAL ELECTRIC SUPPLY/STREET LIGHT/ WATER COOLER) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-X (FIRE FIGHTING) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART-XI (LIGHTNING PROTECTION) Details of prepriced Schedule is given in tender documents.

SCHEDULE "A" PART -XII (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col.' E ' signifies this fact only.

INTERNAL WATER SUPPLY S & F 15 mm Two way bib tap complete all as specified & directed.

INTERNAL ELECTRIC SUPPLY S & F of recessed mounted LED accent light with aluminum die cast housing having 36° beam spread, CCT 4000 K, CRI > 80, initial power input 42 W, PF ≥ 0.9, system efficacy 95 lm/W, IP 20 & IK 02 protection, 2.5 kV surge protection, median useful life L70B50 ≥ 30000 hrs and a replacable flicker free driver having ripple factor < 5% including electrical connection with 3 core 1.0 mm² PVC insulated copper conductor wire from ceiling rose to the fixture complete all as specified and directed. Make: Phillips Cat Part No:- RS271B LED40/840 PSU-E MB WH or techno-commercial equivalent of Bajaj, Wipro

S & F 10 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed by the engineer-in-charge. Make: BAJAJ Cat-Part No. 112408 BCLSB 10 NW or equivalent model of Havells, Philips or Wipro

S & F 20 W surface/wall mounted LED batten having high efficiency long life LED chips with luminous efficacy of > 100 lumen/W, independent isolated SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, polycarbonate diffuser, housed in powder coated white extruded aluminium channel housing and white coloured ABS end caps having input voltage 220- 240 V, input frequency 50- 60 Hz, PF > 0.95, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fixture complete all as specified and directed. Make: BAJAJ Cat-Part No. 112785 BCLAB 20W or equivalent model of Havells, Philips or Wipro

S & F 12 W surface mounted round shape LED down light with minimum efficiency 85 lumen/W, high quality polycarbonate opal concave diffuser, high reflective polycarbonate conicle shape reflector, input voltage 240 V, input frequency 50 Hz including electric connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to fixture complate all as specified and directed by engineer-in-charge. Make: Philips Cat-Part No. SM250C LED12S- 6500 PSU WH or equivalent model of Havells or Wipro

S & F recessed mounted LED downlight with CRCA housing & optical cover having , power rating 6.5 W, luminous efficacy ≥ 100 lm/W, CCT 6500 K, CRI ≥ 80, PF > 0.9, 50000 hrs lifetime @L70B50 at 45 °C, IP 20 & IK 03 protection,median useful life L70B50 ≥ 30000 hrs and a replacable flicker free driver having ripple factor < 5% including electrical connection with 3 core 1.0 mm² PVC insulated copper conductor wire from ceiling rose to the fixture complete all as specified and directed. Make: Philips Cat part No:- DN 391B LED6S-6500 PSU WH or techno-commercial equivalent of Bajaj, Wipro

Supply & fixing of 2.7 W LED foot/ step lighting fixture complete with driver & in all respect including testing & commissioning on completion. Make: BWG150 LED50/NW PSU 220-240V IP67 7043 of Philips or techno-commercial equivalent of Bajaj, Wipro

S & F LED mirror light suitable for wall mounting & 220- 240 V, 50 Hz mains voltage with built-in LED & driver, power rating 7.5 W, including IP 20 protection as well as electrical connection with 3 core 1.0 mm² PVC insulated copper conductor wire to the fixture complete all as specified and directed. Make: Philips cat part No:- 340341486 jojoba or techno-commercial equivalent of Bajaj, Wipro

S & F 25 W LED Building security light having high efficiency long life LED module with SMD LED package mounted on MCPCB with high LED efficacy of ≥ 100 lumen/W, integral SMPS based constant current electronic LED driver with THD < 20%, surge voltage protection and other safety tests as per IS: 15885 (Part-2/Sec-13): 2012, IP 66 protection, high effiency polycarbonate cover with integrated lens housed in pressure die-cast aluminium alloy heat sink for effective thermal management, sturdiness, excellent corrosion resistance, separate optical and control gear compartment & top opening for easy maintenance, suitable for side entry, wall mounting with bracket 1.5 m long with including necessary electrical connection to the fixture with 3 core flexible Cu conductor cable of appropriate size and light grade GI pipe, including GI clamps, nuts, bolts & washers with two coats of synthetic enemal paint over a coat of red oxide primer complete all as specified and directed. Make: BAJAJ Cat-Part No. 169821 BCLST 25W LED I LED I or equivalent model of Havells, Philips or Wipro

S & F BEE five star rated BLDC energy efficient high-speed ceiling fan having 1200 mm blade sweep, air-flow not less than 210 CMM, operating voltage 220-240 V and frequency 50 Hz, including a downroad of suitable size and electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fan complete all as specified and directed. Make: Crompton Cat-Part No. ENTRUST50 or Havells Cat- Part No. ES-50 or equivalent model of Usha or BAJAJ

S & F energy efficient metalic wall mounting fan having blade sweep 450 mm, air delivery not less than 110 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the wall fan complete all as specified and directed. Make: Crompton Cat-Part No. AC450WALL-1 or Havells Cat- Part No. V3 or equivalent model of Usha or BAJAJ

S & F energy efficient non-metalic fresh air fan having blade sweep 250 mm, air delivery not less than 860 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed. Make: Crompton Cat-Part No. VENTILUS 10" or equivalent model of Usha, Havells or BAJAJ

S & F energy efficient metalic exhaust fan having blade sweep 300 mm, air delivery not less than 900 CMH, operating voltage 220-240 V and frequency 50 Hz, including electrical connection with 3 core flexible Cu conductor cable of appropriate size from ceiling rose to the fresh-air fan complete all as specified and directed by engineer-in-charge. Make: Crompton Cat-Part No. EXHD300- 4-1 or equivalent model of Havells or BAJAJ

S & F vertical triple pole & neutral, double door, 4-way metallic modular distribution board conforming to IEC 61439-3, suitable for flush / surface mounting with provision for MCCB up to 250 A as incomer and SP/TP MCBs as outgoing, reversible metal door, fully insulated 250 A copper busbar for each phase, two fully insulated & shrouded neutral bars, two earthbars, cable ties for cable management, prefitted masking sheet, etc. having IK 09 & IP 43 protection complete all as specified and directed by engineer-in-charge. Make: Legrand, Schneider, L & T

S & F MCB for AC applications conforming to IS/IEC 60898-1-2002, having breaking capacity Icn = 10 kA, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP 20 protected lower terminals and sliding shutters, etc. complete all as specified and directed by engineer-in-charge. (a) 6 A, SP MCB, C- curve

(b) 16 A, SP MCB, C- curve

(c) 20 A, SP MCB, C- curve

(d) 20 A, DP MCB, C- curve

(e) 40 A, TP MCB, C- curve

(f) 40 A, FP MCB, C- curve

S & F 100 A four pole moulded case circuit breaker (MCCB), conforming to IEC 60947-2, having Ics = 100% of Icu = 25 kA, adjustable thermal setting (0.7 - 1 X In) and fixed magnetic setting with compression lug connectors and thermal magnetic trip unit (TMD) all complete as specified and directed. Make: Schneider, Legrand, Havells

S & F 40 A four pole moulded case circuit breaker (MCCB), conforming to IEC 60947-2, having Ics = 100% of Icu = 25 kA, adjustable thermal setting (0.7 - 1 X In) and fixed magnetic setting with compression lug connectors and thermal magnetic trip unit (TMD) all complete as specified and directed. Make: Schneider, Legrand, Havells

M & L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6 mm size, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanised steel wire of diameter 4.0 mm as earth lead, by means of bolts, buts, check nuts and washers of galvanised iron or steel, galvanized iron pipe of 15 mm diameter, connected to earthing test point, all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion and including excavation, earthwork, PCC earth pit of dimensions 550 mm X 550 mm (outer) and 300 mm X 300 mm (inner) and 250 mm deep, with a 10 mm thick CI cover, hinged to CI frame on ground level, GI watering pipe, funnel, etc. as all specified and directed.

EXTERNAL WATER SUPPLY Supply and Laying in trenches DI Pipe S/S including joints of suitable size specials K-7 complete of size 100 mm bore.

Cutting road/ footpath in a depth not more than 0.60 m and width not less than 0.40 m for laying pipe line and getting out and returning filling, well ramming in layers and making good and matching with the existing surface after laying of pipes all as specified and directed.

M & L Construction of Valve chamber of size 900 x 600 x 1000 mm in PCC 1:3:6 Block masonry built in CM 1:4 including necessary excavation and earth work, foundation,/PCC bed with PCC 1:4:8 type D2, coping in cement concrete 1:2:4 type B1, plastering 15mm thick with CM 1:4 including MS cover made out of 3.15 mm thick MS Sheet and 40 x 40 x 6 mm size angle iron frame with cross beacings and locking arrangement dult painted with two coats of bituminous black paint over a coat of red oxide primer on all steel surafce as directed

EXTERNAL ELECTRIFICATION/ STREET LIGHT Supply and lay 50 mm Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 14930 (Part-ll) for protection of UG cables, laid in trenches/ road/ drain or fixed along wall, poles or laid under floor all as specified and as directed by Engr-in-Charge. Make-REX/POLY/Gemine

Supply and lay 63 mm Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 14930 (Part-ll) for protection of UG cables, laid in trenches/ road/ drain or fixed along wall, poles or laid under floor all as specified and as directed by Engr-in-Charge. Make-REX/POLY/Gemine

Supply and lay 110 mm Double Walled Corrugated (DWC) Pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 14930 (Part-ll) for protection of UG cables, laid in trenches/ road/ drain or fixed along wall, poles or laid under floor all as specified and as directed by Engr-in-Charge. Make-REX/POLY/Gemine

Supply , install, testing and commissioning LT Panel board cubical type compact, Factory Fabricated, 415 Volts AC 50 Hz, fabricated of Thermoplastic (Polycarbonate), insulated, shock proof, dust proof water proof, articorrosive and confirming to IP 55, indicating lamp LED type (RYB) including wiring with suitable rated PVC insulated copper conductor, complete including copper bus bar 400 Amps 4 strip mounted on porcelain insulated & enclosed in chamber & connection from incoming and out going with openable shutter both sides, mounted on angle iron pedestal made out Gl angle of 50 x 50 x 6 mm, 45cm above GL including PCC platform of suitable size and comprising of following: (a) Copper Bus bar RYB and N of 400 Amp capacity one set (b) 4 Pole MCCB 250 Amp, 50HZ, 415 V with rupturing capacity 35 KA -01 No (Incoming) (c) 4 Pole MCCB 125 to 160 Amp, 50 Hz, 415V with rupturing capacity 35 KA-02 No (Outgoing) (d) 4 Pole MCCB 63 to 100 Amp, 50 Hz, 415 V with rupturing capacity 25 KA-3 Nos (outgoing) (d) Digital multifunction meter for Amp, Volt, KWH, power factor and other parameter flush mounting-01 No MAKE of LT Panel : Hensel/ Universal / Neptune MAKE of MCCB : Legrand/ L&T/ Siemens/ Schneider

M & L for Bore Earthing complete with 250 micron copper bonded earth electrode as per UL-467 standards, 17 mm dia. min cross sectional area 227 sq mm, 3 meters length, Short circuit capacity 10 KA in 1 Sec RMS Value, buried directly and preferably vertically in ground connected with earthing lead of 16 sqmm dia PVC insulated single core copper conductor flexible cable including FRP Chamber and testing on completion all as specified and directed. Note: (i) Dimensions of FRP Chamber should be 300 x 300mm Top, 150 x 150mm Bottom, 200 mm Height and 2 mm Thickness. (ii) Cost of 16 sqmm copper cable and 20 mm dia HDPE pipe (6kg/sqcm) deemed to be included in unit rate up to 7.5 meter. (iii) Value of earth system resistance should be less than 2 ohms. (iv) Cost of Bore hole of 150mm OD upto 3 m deemed to be included in unit rate. (v) Cost of Earth Enhance material to achieve the required result, deemed to be included in unit.rate.

Supply and fix Octagonal Hot-Dip galvanized street light poles including Junction box, Height 6 mtrs, Top dia 70mm, Bottom dia 130 mm, sheet thickness 3 mm, base plate 220 x 220 x 12mm, foundation nut bolts as per manufacturer recommendation including reinforced cement concrete foundation and provision for hot dip galvanised bracket single arm for fixing of street light and one no of MCB 6 Amp including terminal block all as specified and directed. MAKE : Bajaj/ Surya/ Utkarsh

S & F LED street lights, 35/36W, lumen output not less than 3500 Im high pressure die cast aluminium housing, 140-270V, 50 Hz, PF>0.95, including 1.2 mtr long 40/50 mm bore light grade GI pipe mounting bracket made to shape with and including MS clamps of Fl 40mm x 6 mm with bolts, nuts, washers and conductor to fitting with 3 core 1 sqmm PVC insulated copper cable from control box to fitting complete all as specified. Note: The quoted unit rate deemed include for painting to clamps with one coat of red oxide paint before fixing complete all as specified and directed by Engineer - Charge. MAKE: Wipro/ Philips/ GE/ Osram

Supply & fix Automatic Street Light Control Switch using infrared sensor based NATURE SWITCH for automatic switching of Street Lights. Nature Switch operation should be based on Natural Light Lux* level Required illuminance Level for Switching ON is ≤ 30 Lux and for Switching OFF ≥ 10 Lux. The Sensor should also have part night operation facility of min 4 hours to max 12 hours. The Sensor along with sultable Power Contactor(s) and Incoming-Outgoing MCsE should be enclosed in a pole/wall mountable Rust Proof, electric shock proof termite proof and FR grade thermoplastic polycarbonate enclosure conforming to IP66 protection class 2.

WATER COOLER Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4.0 KVA

Supply and fix Pressure gauge 100 mm dia with ball valve of pressure 25 Kg/Sqcm

Supply and fix Automatic air release valve 50 mm dia suitable for domestic water with 50 mm gun metal stop valve complete.

Supplying, drawing, connecting, testing and commissioning of polyethylene insulated, PVC sheathed, overall shielded, multistrand, annealed tinned copper conductor, FRLS signal cable of size 2x1.5 sqmm complete on cable tray/ rake of fixing on wall/ceiling with iron clamp in side conduit pipe complete in all respect including end termination glands, lugs and clamps etc as per IS 1554 all as specified.

S &F Double sided RED LED Entry/Exit signage board with built in battery back – up for 2 hrs in powder coated in CRCA sheet with acrylic sheet all as specified and directed.Make: Bajaj cat part No: BESL 03 LED DSD WBB Red

S&F Fire Extinguisher Dry Chemical powder ABC type, stored pressure type extinguisher of 6 Kg capacity confirming to IS 15683 with ISI marked/ TAC approved including required accesories including wall suspension bracket and all as specified.(at each Entry/Exit)

S&F Fire Extinguisher Carbon Dioxide of 3 Kg capacity confirming to IS 15683 with ISI marked/ TAC approved including required accesories including wall suspension bracket and all as specified. .(at each Entry/Exit)

S&F Fire Extinguisher Dry Chemical powder ABC type, stored pressure type extinguisher of 9 Kg capacity confirming to IS 15683 with ISI marked/ TAC approved including required accesories including wall suspension bracket and all as specified.(at at Entrance lobby and AC plant room, DG set Area and Parking Area)

S&F Fire Extinguisher Carbon Dioxide of 4.5 Kg capacity confirming to IS 15683 with ISI marked/ TAC approved including required accesories including wall suspension bracket and all as specified. .(at Entrance lobby and AC plant room)

S&F Fire Extinguisher Mechanical Foam type, stored pressure type extinguisher of 9 Ltr capacity confirming to IS 15683 with ISI marked/ TAC approved including required accesories including wall suspension bracket and all as specified.(at at Entrance lobby and AC plant room, DG set Area and Parking Area)

Supply & Installation at approved location Fire Sand Bucket of 24 guage galvanized steel sheet, each set shall have 4 buckets with stand and showel etc complete.

FURNITURE Desk Stand Lecture (FD-125)

Receptacle PVC (FD/E6/MAP/13)

Stool 3 feet High Make:- Emerald of Durian or equivalent in Godrej/Featherlite

Table Office for executive officers in wood having walnut color. Make:- DWS-34752 of Durian or equivalent in Godrej/Featherlite

Providing and fixing Auditorium chairs with following specification. The seat assembly shall be made of polyurethane foam moulded with MS tubular frame insert which is uphoistered with fabric. The insert is tubular frame made of at 9 +0.02cm x 0.16 + 0.013cm thick MS ERW round tube with flexible support straps running across the length and width of the frame. The seat shall have Auto tip up feature which shall make it stay in upright position when not in use enabling clear row passage. The seat size shall be 45.5cm (W) x 46.5 (D). The back assembly shall be made of polyurethane foam moulded with MS tubular frame insert shall be uphoistered with fabric and shall have a plastic back cover. The Insert shall be tubular frame made of at.9 +0.02 cm x 0.16 + 0.013 cm thick MS ERW round tube with flexible support straps running across the length and width of the frame. The HR polyurethane foam for shall be moulded with density = 45 +/- 2 kgs/m3. The chair shall rest on the grounds on two side panel frames fabricated from 0.12 + 0.02 cm thick CR steel sheet, which shall be cladded with fabric uphoistery. The side panel frame shall be grouted to the floor, using two numbers of anchors for each panel through. 0.3 + 0.05 thick HR steel base plate. the synchric slide mechanism shall be designed using heavy-duty slides aiding in relaxed posture. The slider shall be connected to back using linkage to achieve synchronous motion between seat and back. The syncro slide shall have a stroke of 60 +/- 5mm and shall be mounted on these side panel. The armrests shall be made up solid. beech wood with clear lacquer coat. The armrest shall be filled with side panel through concealed zinc-plated hinge. The chair shall have a main -Add on concept and common armrest shall be used. Overall height shall be 107.3cm, Seat height 45.5cm depth of chair without seat and backseat slide shall be 50.5cm , depth and seat slide and without back side shall be 63cm. The auditorium chair shall be designed to get mounted /grounted on floors with flooring specifications. The chair shall be of knock down type and shall come in boxes, handles will be with the cup holder or without cup holder as required. MAKE : STELLAR - DURIAN or equivalent in Godrej and Featherlite

Providing and fixing Auditorium chairs with following specification. The seat assembly shall be made of polyurethane foam moulded with MS tubular frame insert which is uphoistered with fabric. The insert is tubular frame made of at 9 +0.02cm x 0.16 + 0.013cm thick MS ERW round tube with flexible support straps running across the length and width of the frame. The seat shall have Auto tip up feature which shall make it stay in upright position when not in use enabling clear row passage. The seat size shall be 45.5cm (W) x 46.5 (D). The back assembly shall be made of polyurethane foam moulded with MS tubular frame insert shall be uphoistered with fabric and shall have a plastic back cover. The Insert shall be tubular frame made of at.9 +0.02 cm x 0.16 + 0.013 cm thick MS ERW round tube with flexible support straps running across the length and width of the frame. The HR polyurethane foam for shall be moulded with density = 45 +/- 2 kgs/m3. The chair shall rest on the grounds on two side panel frames fabricated from 0.12 + 0.02 cm thick CR steel sheet, which shall be cladded with fabric uphoistery. The side panel frame shall be grouted to the floor, using two numbers of anchors for each panel through. 0.3 + 0.05 thick HR steel base plate. the synchric slide mechanism shall be designed using heavy-duty slides aiding in relaxed posture. The slider shall be connected to back using linkage to achieve synchronous motion between seat and back. The syncro slide shall have a stroke of 60 +/- 5mm and shall be mounted on these side panel. The armrests shall be made up solid. beech wood with clear lacquer coat. The armrest shall be filled with side panel through concealed zinc-plated hinge. The chair shall have a main -Add on concept and commom armrest shall be used. Overall height shall be 107.3cm, Seat height 45.5cm depth of chair without seat and backseat slide shall be 50.5cm , depth and seat slide and without back side shall be 63cm. The auditorium chair shall be designed to get mounted /grounted on floors with flooring specifications. The chair shall be of knock down type and shall come in boxes, handles will be with the cup holder or without cup holder as required. MAKE : ARENA - DURIAN or equivalent in Godrej and Featherlite

Supplying, installation, testing and commissioning of 14 HP capacity modular type outdoor units equipped with highly efficient scroll/rotary all inverter type compressors, equipted with special heat exchanger, Y branch, outdoor unit support, auto check function facility, auto addressing setting, COP not less than 3 at 100% Load and 4.0 at 50% Load at 35°C DBT ambient temperature & at 27°C DBT/19°C WBT inside temperature respectively,R 410A Refrigerant, lubricating oil and all other accessories. Outer casing of the Out Door Unit should be factory coated with rust prevention coating and suitable for working on 48°C ambient temperature. The ODU shall be complete with Micro-processor control panel, sub cooler, accumulator, isolating valves (service valves) etc. complete as required. Units should be Heat pump model.

Supplying, installation, testing and commissioning of 32 HP capacity modular type outdoor units equipped with highly efficient scroll/rotary all inverter type compressors, equipted with special heat exchanger, Y branch, outdoor unit support, auto check function facility, auto addressing setting, COP not less than 3 at 100% Load and 4.0 at 50% Load at 35°C DBT ambient temperature & at 27°C DBT/19°C WBT inside temperature respectively, 410A Refrigerant, lubricating oil and all other accessories. Outer casing of the Out Door Unit should be factory coated with rust prevention coating and suitable for working on 48°C ambient temperature. The ODU shall be complete with Micro-processor control panel, sub cooler, accumulator, isolating valves (service valves) etc. complete as required. Units should be Heat pump model.

Supply , installation ,testing and commisioning of factory built /site assembled EN1866 equivalent AHRI/IS Certified with equivalent leakage class Air handling units in Double skin type (Casing shall be of Non-Skeleton construction)with 40+/- 2 or 45+/- 2 thick panels with thermal break construction consisting of G.I casing of thickness 0.6 mm outside layer and 0.6 mm inside layer with 275 GSM or eqvivalnet zinc coating and polyurethene foam(PUF) insulation having density of 42 kg/m3,compIete with Backward curved aerofoil blade Plug type direct driven fan of Aerofoil design bladealongwith VFD suitable for static pressure as detailed below, chilled water cooling coil with aluminium finned copper tubes. Filter section having pre (EU4, more than 90% efficiency for 10 Microns), fine (Bag filter MREV 13 or higher), UV lamps, IE3 motor suitable for 415 +10% voIts,50 Hz, 3 phase AC suppIy,drain connections with stainless steel drain pan and necessary vibration isolation arrangement to avoid any vibration etc. complete as per specifications and drawings. The static pressure should be verified as per actual site conditions. Mist elimintaor should be part of AHU. The dimesion of AHU to be approved by customer. VFD should be capable to controll the speed of the fan and compatible with BMS integration for Fan speed control. Total static13000 CFM and 64 H P cooling capacity Note: Requirement of parameters like as inside temperature and relative humidity as included in particular specification on page No 218(P) of tender.

Supplying, installation, testing and commissioning of copper refrigerant piping suitable for VRV/VRF system for Refrigerant R 410A, complete with fittings, jointing, 19 mm thick insulation with XLPE class 0 tubular insulation/0 Class Nitrite Rubber as per specification complete etc. as required of 9.5 mm (OD)(Soft Drawn) with tube thickness 1.2 mm with 19 mm thick insulation.

Supplying, installation, testing and commissioning of copper refrigerant piping suitable for VRV/VRF system for Refrigerant R 410A, complete with fittings, jointing, 19 mm thick insulation with XLPE class 0 tubular insulation/0 Class Nitrite Rubber as per specification complete etc. as required of 12.7 mm (OD)(Soft Drawn) with tube thickness 1.2 mm with 19 mm thick insulation.

Supplying, installation, testing and commissioning of copper refrigerant piping suitable for VRV/VRF system for Refrigerant R 410A, complete with fittings, jointing, 19 mm thick insulation with XLPE class 0 tubular insulation/0 Class Nitrite Rubber as per specification complete etc. as required of 15.86 mm (OD)(Soft Drawn) with tube thickness 1.2 mm with 19 mm thick insulation.

Supplying, installation, testing and commissioning of copper refrigerant piping suitable for VRV/VRF system for Refrigerant R 410A, complete with fittings, jointing, 19 mm thick insulation with XLPE class 0 tubular insulation/0 Class Nitrite Rubber as per specification complete etc. as required of 19.1 mm (OD)(Hard Drawn) with tube thickness 1.2 mm with 19 mm thick insulation.

Supplying, installation, testing and commissioning of copper refrigerant piping suitable for VRV/VRF system for Refrigerant R 410A, complete with fittings, jointing, 19 mm thick insulation with XLPE class 0 tubular insulation/0 Class Nitrite Rubber as per specification complete etc. as required of 28.6 mm (OD)(Hard Drawn) with tube thickness 1.2 mm with 19 mm thick insulation.

Supplying, installation, testing and commissioning of copper refrigerant piping suitable for VRV/VRF system for Refrigerant R 410A, complete with fittings, jointing, 19 mm thick insulation with XLPE class 0 tubular insulation/0 Class Nitrite Rubber as per specification complete etc. as required of 34.9 mm (OD)(Hard Drawn) with tube thickness 1.62 mm with 19 mm thick insulation.

Supplying, installation, testing and commissioning of refrigerant piping Y joints set i/c brazing complete as required to connect the indoor units.

Supplying, installation, testing and commissioning of 25 mm dia PVC drain water piping complete with fittings (eIbows,tees, reducers,sockets,u trap etc.) supports, jointing duct insulated with XLPE class 0 tubular of 9 mm thick insulation/0 Class Nitrile rubber etc. complete as required.

Supplying, installation, testing and commissioning of 32 mm dia PVC drain water piping complete with fittings (eIbows,tees, reducers,sockets,u trap etc.) supports, jointing duct insulated with XLPE class 0 tubular of 9 mm thick insulation/0 Class Nitrile rubber etc. complete as required.

Supplying, installation, testing and commissioning of 40 mm dia PVC drain water piping complete with fittings (eIbows,tees, reducers,sockets,u trap etc.) supports, jointing duct insulated with XLPE class 0 tubular of 9 mm thick insulation/0 Class Nitrile rubber etc. complete as required.

Supplying, installation, testing and commissioning of condensate pump suitable for lifting water up to 5m head at 550 L/Hr. discharge, rated current capacity 0.8 amp at 230 V, 50 Hz AC supply, incorporate 3.0 amp safety switch, complete with 2 metre length power cable etc. complete as required.. (Make :- ASPEN Hi- Flow/ Siccom)

Supplying and installing following size of perforated painted with powder coating MS cable trays /Hot dipped galvanised iron cable tray with perforation not more than 17.5%, in convenient section, joined with connectors, suspended from the ceiling with GI/MS suspenders including bolts & nuts, painting suspenders etc as required.a) 150 mm width x 50 mm depth x 1.6 mm thickness

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular / round ducting as per IS 655 2006 complete with neoprene rubber gaskets , elbows , splitter dampers,vanes,, hangers ,supports etc. as per apporved drawings and specifications of 0.63 mm sheet thickness complete all as required

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular / round ducting as per IS 655 2006 complete with neoprene rubber gaskets , elbows , splitter dampers,vanes,, hangers ,supports etc. as per apporved drawings and specifications of 0.80 mm sheet thickness complete all as required

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular / round ducting as per IS 655 2006 complete with neoprene rubber gaskets , elbows , splitter dampers,vanes,, hangers ,supports etc. as per apporved drawings and specifications of 1 mm sheet thickness complete all as required

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air grill of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Supplying, fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.

Supplying and fixing of 25 mm thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “0”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Supply and fixing of acoustic insulation for supply air duct and plenum with 25 mm thick nitrite rubber open cell foam with density 140-180 Kg/m3 passing class 1 fire performance test as per BS476 part 7, air erosion test for 10000fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection i/c rubber based adhesive complete as per specification and as required.

Supplying, installation, testing and commissioning of indoor type floor mounted compartmentalized cubical type metre panel board made out of 2 mm thick CRCA sheet, dust and vermin proof, well ventilation (IP 42), front opening hinged type doors with pad lock, separate compartmentlized arrangement for energy metre with looking glass/wiremass for taking metre reading, neophrine gasket & locking arrangements, 600 mm deep with suitable size 4 strip aluminium busbar of 300 amp capacity of suitable length with heat shrinkable sleeves, 3 Nos. LED indicator lamps, earthing all the metallic parts, cable alleys for cable terminal, suitable for accomodation of the following switchgears and accessories.i/c connection, interconnections with adequate size of FRLS PVC insulated single core copper cable of suitable size door earthing with 4 Sq.mm FRLS grade PVC insulated copper conductor single core cable and 1 No. M.V danger notice plate of 200 mm X 150 mm made of mild steel, at least 2.00 mm thick and vitreous enamelled white on both sides and inscription in signal red colour on front side, powder coated painting of siemens grey colour, after cleaning & finishing in 7 or more tanks process, 75 mmX 50 mmX 4.4 mm M.S base channel with anticorrosive paint, earthing etc.as required. (Size of panel 1150 mm X 1350 mm Approx.) i) 100 A, Microprocessor release based 4 pole, 50 KA, MCCB, Ics = 100% Icu as per IEC 60947-2 for adjustable short circuit and overload settings, inbuilt ground fault protection i/c extended rotary handle, spreader terminals, phase barriers etc. = 2 Nos. iii) 63 A, Thermal magnetic release based 4 pole, 25 KA, MCCB, Ics - i00% lcu as per IEC 60947-2 for adjustable short circuit and overload settings i/c extended rotary handle, spreader terminals, phase barriers etc. = 1 No. iv) 40 amp. TPN MCB, "C" curve, 10 KA = 1 No. v) 10 amp. SPN MCB, "C" curve, 10 KA — 7 Nos. vi) Fire Damper Integration as required for Fire Safety Norms

Supply & Installation of interconnecting control & transmission Copper wiring 2C x 1.5sqmm as communication cable required in PVC conduit.

Supplying and laying of following XLPE insluated PVC sheathed copper conductor armoured cable 1100 volts complete with cable tray clamps, saddles, thimble cable gland etc including effective proper connection to the equipment as required. (Make :- Polycab / KEI / Havells / RR Kabel of ISI marked) a) 4 X 10 sq.mm (For 14 HP)

Supplying and laying of following XLPE insluated PVC sheathed copper conductor armoured cable 1100 volts complete with cable tray clamps, saddles, thimble cable gland etc including effective proper connection to the equipment as required. (Make :- Polycab / KEI / Havells / RR Kabel of ISI marked) a) 4 X 25 sq.mm (For 32 HP)

Supplying and laying of following XLPE insluated PVC sheathed copper conductor armoured cable 1100 volts complete with cable tray clamps, saddles, thimble cable gland etc including effective proper connection to the equipment as required. (Make :- Polycab / KEI / Havells / RR Kabel of ISI marked) a) 2 X 10 sq.mm ( For earthing)

Supplying and laying of following XLPE insluated PVC sheathed copper conductor armoured cable 1100 volts complete with cable tray clamps, saddles, thimble cable gland etc including effective proper connection to the equipment as required. (Make :- Polycab / KEI / Havells / RR Kabel of ISI marked) a) 4 X 5 sq.mm (For 1.5, 2 TR IDU)

Supplying and laying of following XLPE insluated PVC sheathed copper conductor armoured cable 1100 volts complete with cable tray clamps, saddles, thimble cable gland etc including effective proper connection to the equipment as required. (Make :- Polycab / KEI / Havells / RR Kabel of ISI marked) a) 2 X 5 sq.mm (For Earthing)

Earthing complete with galvanised steel earth plate electrode 600mmx600mm.x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less’than 1.5 metres below normal ground level, connected to galvanised earth lead wire but using galvanised iron strip 32x6mm as earthing lead all as specified and directed.

The plant supports shall consist of a galvanised steel frame supported by adjustable leg and feet assemblies The frame dimensions should be designed to take the weight with minimal deflection, and should be manufactured from hot dip galvanized carbon steel: BS EN 10219-1 to a welding standard: BS EN ISO 15614 The galvanizing standard to be BS EN ISO 1461 with salt mist testing to BS EN 60068-2-52. The feet shall be 150mm square made from Nylon 6 B601L 30% glass fibre filled.Bound usir›g a ratio of high-quality moisture curing polyurethane pre-polymer to BS 7188 and BS 5696-3.The leg assembly is fixed at minimum 300.mm Load bearing strength should be not less than 500/600 kg/stand. Third party certification should be provided for Load bearing strength. Minimum Dimension. (L * W) (930 mm x 765 mm)

The plant supports shall consist of a galvanised steel frame supported by adjustable leg and feet assemblies The frame dimensions should be designed to take the weight with minimal deflection, and should be manufactured from hot dip galvanized carbon steel: BS EN 10219-1 to a welding standard: BS EN ISO 15614 The galvanizing standard to be BS EN ISO 1461 with salt mist testing to BS EN 60068-2-52. The feet shall be 150mm square made from Nylon 6 B601L 30% glass fibre filled.Bound usir›g a ratio of high-quality moisture curing polyurethane pre-polymer to BS 7188 and BS 5696-3.The leg assembly is fixed at minimum 300.mm Load bearing strength should be not less than 500/600 kg/stand. Third party certification should be provided for Load bearing strength Minimum Dimension. (L “ W) (1240 mm x765 mm)

The plant supports shall consist of a galvanised steel frame supported by adjustable leg and feet assemblies The frame dimensions should be designed to take the weight with minimal deflection, and should be manufactured from hot dip galvanized carbon steel: BS EN 10219-1 to a welding standard: BS EN ISO 15614 The galvanizing standard to be BS EN ISO 1461 with salt mist testing to BS EN 60068-2-52. The feet shall be 150mm square made from Nylon 6 B601L 30% glass fibre filled.Bound usir›g a ratio of high-quality moisture curing polyurethane pre-polymer to BS 7188 and BS 5696-3.The leg assembly is fixed at minimum 300.mm Load bearing strength should be not less than 500/600 kg/stand. Third party certification should be provided for Load bearing strength Minimum Dimension. (L ” W) (4500 mm * 2600 mm)

S & F RDM Compatible DMX Splitter with 1 DMX in and optically isolated 8 DMX out port for DMX network• Splitter enclosure made up of MS 18/16 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Mattblack texture finish.• Control Protocol RDM and DMX 512• 2 DMX input 5 pin XLR Connectors• 8 optically isolated DMX output 5 pin XLR Connectors • IEC male plug to power supply the splitter • Splitter must be compact of Size : 145 x 483 x 45mm or less• Splitter bracket for mounting or 19” rack mountMake : Leksa Lighting/ ADB/ Selecon/ Modern Stage Light/ Canara Lighting/Daylight/Robe/Martin

S & F Digital Lighting Console with Ultimate portability, offering a powerful LED and moving light controller in a small 19” unit with direct access to each of the lights.• 1024 DMX Channel • LCD Display for user interface • RDM compatible • Control up to 120 LED, moving lights and conventionals• multi-function fadersMake : Leksa Lighting/ ADB/ Selecon/ Modern Stage Light/ Canara Lighting/Daylight/Robe/Martin

S & F PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm.Make: Walna / SBEE / Polycab / KEI

S & F FRLS PVC copper multistrand flexible cable 7 core x1.5 sq.mm.Make: Walna / SBEE / Polycab / KEI

S & F FRLS PVC Copper armoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 4cx4 sq mm.Make: Walna / SBEE / Polycab / KEI

S & F FRLS 5 Core DMX signal cable for DMX network.Make: Falcon / Beldon / Deepcab / Polycab.

S & F Die cast Aluminium C - Clamp with safety chain duly epoxy polyester powder coated in black matt texture finish and safe working load of 100kg with below specifications.• Lock - MS threaded Galvanized lock key,• Plastic Glass filled nylon moulded M6 key.• Receptacle - 28mm standard TV spigot.• Safety - MS Galvanized chain with pin.• Finish - Pretreated and black epoxy polyester powder coated.• Self-weight - 0.54Kg

S & F Safety bond with lock clip 1.5 Mtr Long made with twisted pair of GI wire rope 3mm thick with sleeve to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly. SWL 100Kgs.

S & F 79mm Round Identification name plate duly epoxy polyester powder coated in matt texture finish.

S & F MS Fabricated Lighting Junction box made up of 22SWG CRCA for LED lighting fixtures, black epoxy polyester powder coated, with 4 way 10A IEC sockets and pipe clamp arrangement with below specifications.• Fixing : Snap fit /15 (1.5mm),• Junction Box must be compact of Size : 140 x 112 x 50mm or less• Pipe clamp arrangement for fixing or Rawl plug arrangement for wall/floor fixing

S & F MS Fabricated 2 way IEC Junction box with rocker switch to power splitter and console made up of 22SWG CRCA, black epoxy polyester powder coated and pipe clamp arrangement.• DPST 4 Pins Toggle Button Rocker switch• Junction Box must be compact of Size : 140 x 112 x 50mm or less• Pipe clamp arrangement for fixing or Rawl plug arrangement for wall/floor fixing

S & F MS Fabricated 5 pin DMX Signal IN Junction box fitted with 5 pin DMX Male plug made up of 22SWG CRCA, black epoxy polyester powder coated and pipe clamp arrangement with below specifications.• 5 pin XLR DMX IN (Male plug) of reputed make connector,• Extra high temperature resistant insulator material,• All metal housing offers best overall RF protection & electromagnetic shielding,• New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination,• Optional connection to easily join pin 1 to chassis ground.• Junction Box must be compact of 125 x 112 x 50mm or less• Pipe clamp arrangement for fixing or Rawl plug arrangement for wall/floor fixing

S & F MS Fabricated 5 pin DMX Signal OUT Junction box fitted with 5 pin DMX Female plug made up of 22SWG CRCA, black epoxy polyester powder coated and pipe clamp arrangement with below specifications.• 5 pin XLR DMX OUT (Female plug) of reputed make connector,• Extra high temperature resistant insulator material,• All metal housing offers best overall RF protection & electromagnetic shielding,• New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination,• Optional connection to easily join pin 1 to chassis ground.• Junction Box must be compact of 125 x 112 x 50mm or less• Pipe clamp arrangement for fixing or Rawl plug arrangement for wall/floor fixing

S & F MS Fabricated 5 pin DMX Signal Loop Junction box fitted with 5 pin DMX male & female plug with 0.3 Mtrs FR DMX Cable with cable mount plug made up of 22SWG CRCA, black epoxy polyester powder coated and pipe clamp arrangement with below specifications.• 1 Nos each of 5 pin XLR DMX IN (Male plug) & 5 pin XLR DMX OUT (Female plug) of reputed make connector,• 0.3 Mtr Length Dmx Cable with Cable mouth 5 Pin XLR Male & Female loop Cable.• Extra high temperature resistant insulator material,• All metal housing offers best overall RF protection & electromagnetic shielding,• New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination,• Optional connection to easily join pin 1 to chassis ground.• Junction Box must be compact of 140 x 112 x 50mm or less• Pipe clamp arrangement for fixing or Rawl plug arrangement for wall/floor fixing

S & F MS Fabricated Auxilliary marshalling box made up of 22SWG or lesser SWG CRCA sheet, black epoxy polyester powder coated with hinged door and screw lock with below specifications.• MS fabricated Auxiliary marshalling boxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish.• CE certified FC/PG 7 & 11 cable entry gland required Nos as per cable entry.• MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap.• Grey terminal connector with each line having P, N, E Indication for each line incoming and outgoing cable connectors.• Box door must be made with Hingeable door with screw lock.• Pipe clamp arrangement for fixing

S & F MS Fabricated Motor Cable Termintion box made up of 22SWG or lesser SWG CRCA sheet, black epoxy polyester powder coated with hinged door and screw lock• MS channel arranging to fix grey terminal connector, required nos with separation plate and each end is completed with adding end plate with end cap.• Grey terminal connector with each line having L1, L2, L3, E, 6 , 2 , 4 Indication for each line incoming and outgoing cable connectors (L1, L2, L3, E for Power supply & 6 , 2 , 4 for Limit Switch connection) polyster powder coated in black matt texture finish.

S & F 5 pin XLR male / female connectors of made up of Extra high temperature resistant insulator material, Larger solder contacts for easier termination of reputed make.

S & F5 Pin XLR Termination plug made up of extra high temperature resistant insulator material, Larger solder contacts for easier termination with 120 Ohm resister with 0.25Watt for signal termination of reputed make.

S & F MS perforated trays Size 40 x 75 x 40mm & 1.6 mm Thickness undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt black texture finish along with clamping arrangement.

S & F MS Fabricated 50A Direct Lighting distribution Board with MCB Panel made up of 14SWG / 16SWG S & F 18 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt Siemens grey texture finish with following specifications• Main Incomer 50A TPN. 1 Nos • Out Going 10A SP MCB’s for Lighting Junction Box 24 Nos. Out Going 6A SP MCB’s for Splitter & Console 4 Nos. R, Y, B Indicator lamp, • CE certified Nylon FC/PG11 7 & 21 glands for outgoing cables as per requirements • 1 1/8" or Higher size Brass gland for incoming cable • MS MCB channel required length for fixing of MCB’s • All the MCB's identified by a Name plate with suitable code/Number,• All the cables inside the panel routed through gray color cable through all the cables used inside the panel should be FRLS PVC Insulated copper multistrand flexible and must have ISI Marking.• All the outgoing cables terminated through Grey terminal connector with each line having P, N, E Indication. • Panel Including wiring and bus bar connection with proper earthing.• Panel with Hingeable door with key door lock complete. Wall Mount Arrangement.

S & F MS Fabricated Combined 3 Way Motor Control Center panel cum Remote Control panel for Lightbar system made up of 14SWG / 16SWG / 18 SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly epoxy polyester powder coated with Matt siemen’s grey texture finish with following specifications.• 16A TP or TPN Incomer 1 Nos • All the FRLS PVC ISI Marking cables inside the panel routed through PVC gray color cable through. • Red Color Mushroom head push button for emergency stop • All the cables inside the panel routed through PVC gray color cable trough. • Panel Including wiring with proper earthing.

S & F Internal earthing copper bare conductor of size 10 SWG for power network related to work coming under the scope, as directed by Engineer in charge

S & F Installation hardware’s such as clamps, connectors, glands, lugs, ferrules, welding rods and miscellaneous items required during installation work.as directed by Engineer in charge

S & F Valcro Tape (White if available)

S & F of MAIN CURTAIN made out of velvet curtain cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP motor 2nos. air breaker contactors 2nos. micro switches for auto stop, 3 nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900mm and should be stitched in double gathering, with Main Valance.Size:- 14.6 m X 5.9 m Make : Canara Lighting/Modern Stage Service / Stage Technologies / Sholite

S & F REAR CURTAIN made out of glazed cotton cloth with horizontal sliding arrangement complete with fixing rails, brackets, sliding arrangement & motorised operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP single phase motor 2nos. air breaker contactors 2nos. micro switches for auto stop, Dual 3 nos push buttons for forward, reverse and stop positions. The curtain should be draped to half area when in closed position. Minimum overlap at centre should be 900 mm and should be stitched in 50% gathering.Size : 13.5 m X 5.9 mMake : Canara Lighting/Modern Stage Service / Stage Technologies / Sholite

S & F of FRILLS :-Providing and fixing average frills made out of 50% gathering glazed cotton cloth to be installed above the stage on 40NB MS pipe duly powder coated.Size:- 12.5 m X 1.4 mMake : Canara Lighting/Modern Stage Service / Stage Technologies / Sholite

S & F of CYCLORAMA CUM SCREEN :-Cyclorama Screen in Plastic Perforated Material. The screen to be fixed on frame made out of MS/Aluminium material with drum tight arragment. Size : 10.5 m X 5 mMake : Canara Lighting/ Galalite / Dalite / Rosco

S & F MS, Masking Legs (Wings) made out of 25X25mm MS square pipe with 2mm in thickness powder coated of size as per drawing/as under, provided with 1.5meter leg track with grid mount brackets made of 40X50X40mm C track, Pilotable 4- wheeled suspension trolley, Adjustable floor locking screw jacks with rubber grips, .Size:- 1.5 m X 5 mMake : Canara Lighting/Modern Stage Service / Stage Technologies / Sholite

S & F M.S. Pipe Ladders to be provided on sides of the Stage to be fixed on the GI pipe or top grid for fixing of side lights. Made of 40NB MS pipe with suitable suspenders.Size: - 0.6 m X 1.8 mMake : Canara Lighting/Modern Stage Service / Stage Technologies / Sholite

S & F Fixed Stage & Front of House house Light Bar, length 12 Mtrs made using MS 40NB Class ‘B’ Pipe dual barrel construction arrangement undergone through various chemical treatment to keep them rust free and duly epoxy polyester powder coated in black matt texture finish with Below Specifications:• Dual barrel Light bar equipped with 40x75x40 Cable trenching arrangement with lid for better aesthetic look and cable safety. • Dual barrel pipe construction welded with 75x6mm MS Flat in every 1 Mtr for better strength• With Suitable Suspenders to fix the light bar with every 2mtr pitch.Make : Canara Lighting/Modern Stage Service / Stage Technologies / Sholite

DG SET Supplying, installing, testing and commissioning diesel engine driven generating set 415 V, 3 phase, 4 wire as per BS 5514/ IS 10002 complete including automatic on main failure (AMF) panel complete with relay for automatic operation on failure, of capacity 160 KVA at NTP conditions with acoustic enclosure as per latest CPCB emission norms and including PCC foundation of required size as recommended by the manufacturer & comprising of the following: a) Engine: Inline Engine 6 cylinder, heavy duty, turbocharged and after cooled diesel engine, water cooled with standard integral set mounted radiator system suitable for operation at 50 degree Celsius ambient temperature, G2 class Mechanical governing mechanism all aS per BS-5514 IS-3046,1500 RPM, complete with all safety accessories and suitable for generating set application and capable to produce an output of 160 KVA /128 KW And 194 BHP. (i) Starting System - 12 Volts DC electric starter with required 12 V 130AH batteries and charging alternator, engine wiring harness and sensors as required. (ii) Fuel System - Combined unit Injectors, Mechanical governor & as per Is 1460 replaceable fuel filter elements with primary filter and fuel piping.complete with integral fuel tank of minimun capacity suitable for 8 hrs running of DG set at full load, provided with drain plug, air vent, inlet & outlet connection, level indicator and provn for cleaning. (iii) Lube Oil System - Lube oil circulation pump with safety valve, Lube oil filter, Lube oil cooler, Oil filler neck and oil dipstick for measurement, Open crankcase venting system etc. (iv) Combustion Air System.- Exhaust turbocharger, Charge Air Cooler mounted an engine, exhaust flexible bellows, residential type exhaust silencers and extended silencer pipe of same size up to 1.0 Mtr duly insulated and aluminium cladded as directed. (v) Cooling System - Gear driven coolant pump required for both Jacket and intercooler along with necessary pipings on the engine. Water Pump should have suitable capacity to circulate cooling water to radiator mounted on the DG Acoustic Enclosure. (vi) Engine Mounting - Engine mounting bracket with AVM pads mounted below base frame housing engine and alternator.

(b) Alternator - Self regulated self exited brushless alternator, 415 V, 3 phase, 4 wire, 50 Hz, S1 Duty, 160 KVA 128 KW at 0.8 P.F,1500 RPM, with voltage variation plus or minus 10% of rated voltage from no-load to full-load, foot mounted, screen protected drip proof type with class H' insulation with IP-23 ingress protection, ball/ roller bearings at both ends of the alternator shaft with necessary controls as recommended by the manufacturers. (i) Engine Control Panel: Electronic controller for indicating Engine parameters, emergency stop push button, genset monitoring and display of engine alternator operating parameters and alarms, genset protection against critical operating parameters, automatic start sequence control, acquisition and display of plant related measuring data. Features: Auto and mannual Start/Stop, Easy accessible. Display Engine Parameters - RPM, Oil Pressure Coolant, Temperature, Hour Meter, Battery Volts, Battery Charging Voltage, Running Status, Event Recording, Fault Code display Electrical Parameters: Voltage, Current, Hz, KW, KVA, Pf, kWh and KVAr, Breaker Status Engine Protection: High /low coolent Temperature, Low Lube oil Pressure, Engine over speed shutdown Electrical Protection: Overcurrent, short circuit, under/over frequency, under over voltage. (ii) AMF Panel: Floor mounted, vertical, totally enclosed cubical with canopy, out door type dust and vermin proof, standard industrial pattern, factory fabricated out of 2.0 mm thick CRCA steel sheet painted with one coat of red oxide primer and two coats of powder coating of approved colour, complete with all mounting structures, insulators, bolts, nuts, washers etc with necessary control wiring/ internal connections with proper size of copper conductor cables / strips, suitable for 3 phase, 4 wire, 50Hz 415 volts AC system, comprising of microprocessor based AMF relay unit with sensing on mains and DG with necessary protection, Suitable Rating HRC Fuses and 2 Nos 4 pole power contactor of 250 Amps for Mains and DG supply, frequency meter, HRC fuses, push buttons for start / stop / reset, LED type indicating lamps as required, SMPS based battery charger with automatic float & boost changeover facility, control circuit fuses, reverse power relay, alarm for high water lube oil temp and low lub oil pressure,

- any control devices /measuring instruments recommended required as per latest engineering practices complete with cable glands with gland plate for cable entry, control cabling with copper conductor armoured multi-core cables of required cross sectional area from DG set to control panel all prewired and suitable for 160 KVA DG set all as specified. (iii) Acoustic Enclosure - The engine and alternator will be coupled aligned and mounted on a specially designed common base frame fabricated from MS sheets/ channels of suitable cross sectional area and length with bottom drilled holes suitable for and including supplying and fixing anti vibration pads. Outdoor Acoustic enclosure to be provided as per CPCB norms. Acoustic base frame shall be Fabricated using sheet / ISMC Channels with adequate stiffeners for strength. Should be Fabricated with Specially Formed CRCA Sheet metal of 1.5 mm thick shells with adequate stiffners for strength. Door Construction should be prefabricated CRCA sheet with double stepped formation. Doors to be fixed to mainframe by hinges. Suitable sealing given at all the panel joints to avoid the sound & water leakage. the Acoustic Enclosure panels shall be powder coated using minimum of 9 tank process which should include intermediate rinsing modes between each step. (iv) First fill of Pre mix Corrosion inhibitor coolant (v) First fill of lube oil should be supplied along with DG set (vi) First set of fuel filter airfilter lube oil filters etc, consumables should be part of DG set supply. (vii) Any other devices/accessories required as per latest engineering practices as recommended/supplied by the manufacturers as standard eqpt. (vil) Documents : Two sets of following documents -- Maintenance and operation manuals for engine and alternator, spare parts catalogue, warranty/test certificates, wiring schematic diagrams of control panels.

(ix) DG set shall be tested for a duration of 12 Hrs at site using resistive load Bank. Cost of load bank and diesel required for testing at site shall deemed to be inclusive in the quoted rate. (x) Control cables required for all auxiliaries shall be included in quoted rate The length between DG AMF panel and DG set can be taken as max of 30 Mtrs. Make of DG set: Original Equipment Manufacturers : Powerica/ Kirloskar/ Jackson / Greaves Cotton Engine Make:- Cummins/ Kirloskar/ Greaves Cotton Alternator make:- Stamford/ Kirloskar/ Greaves/ Meccalte

m/s.a.t.odedra

Vijay Construction Co

Parth Infrastructure Pvt. Ltd.

M/s PRABHU DAN DETHA AND COMPANY

M/s SK Traders

Hi Tech Transpower Pvt Ltd