PM JANMAN PROGRAM ADIMJUTH VASAHAT 2025-26, PROPOSED FURNITURE WORK IN MULTY PURPOSE COMMUNITY HALL AT KAPARADA TALUKA , DIST - VALSAD. (KPR/MPC-1, Total 3 nos Work) (1) Bhandarkatchcha (2) Vadset (3) Valveri

Item No. Quantity Unit Amount

Reference to Book of Specifications) Figures

1 Providing & fixing & making Table LxBxH (1.80 x 0.90 6.00 Nos 44894.50

x 0.75) using Ply Wood ISI Brand Using IS

Plywood ( 8mm, 10mm, 12mm, 19mm, & 25mm) Top

with All side square top for superior quality table with

thickness of 25 mm.All the outer & Inner surface cover

by I.S.I. brand Sunmica of Formica , silicone ,bloom

green or equivalent & inner 1.5mm thick Laminate

Sheet silicone or bloom or equivalent Brand.using

drawer channel of Hetich brand & handle s.s. matt &

drawer lock , including S.S Screws , necessary hardware

etc. complete including necessary polish, hardware and

labour etc. As per attached drawing & instructed by in

charge Consultant. key board tray, CPU stand Ebaco

Brand, drawer cabinat,horizontal - vertical cable cover,

LEG frame )

2 Providing and fixing of EXECUTIVE OFFICE CHAIRS 6.00 Nos 15756.00

of pvc base and armrest,80 density high mould foam in

seat and back,or mesh, pu upholstry,multi funtional

mechenism, bifma class IV gas lift and p.a

castors,REVOLVING chairs as per the specified

company of HOF, Feather light, Wipro, Godrej etc.as per

instruction of architect or Engineer-in charge

3 Providing and placing of Chair With Extra Support Of 300.00 Nos 2777.50

Pips Must Be required For Long Time Usage Chair

Overall Size (approx): H-83 x W-52 x D- 60 (cm)

Material Description: Seat & Back: Seat & back from

hot mould plywood of minimum 12 mm thickness of

ergonomic design to avoid back pain. Cushioning: PU

foam having density of 40 kg for back and 50kgs/m3 for

seat. Average thickness of foam not less than 50 mm +

10 mm Polly foam.

Tapestry: Minimum average weight required 400to490

gms per sq. mtr,with average weight of 450 grams per

square meter ● Frame structure: 4 legs type Frame and

handle for arm rest from ERW prime quality tube of

swg, reinforced at all bends for static and impact load

with cushioning effect

● Finishing: All steel parts will be epoxy polyester

powder coated to the thickness not less than 50 microns

finish after 10 tank anti-rust treatment and B grade

phosphating (in house) & same will be demonstrated to

the Engineer incharge during pre-dispatch Inspection.

● Product Shoud be Tested by approved BIFMA

standard laboratories confirming to ANSI/BIFMA X 5.1-

2002 Cl. No. 5,7,8,12,13,17 on functional requirement.

Certificets Should be submiting With Supply

,Without certificets Product Will Not Be Accepted.All

work must be done As per Architect Drawing &

Instructed By Site Engineer

SHEDULE B Page

Description of Item (With brif Specification And Rate in

Item No. Quantity Unit Amount

Reference to Book of Specifications) Figures

Rupees Eleven Lakh NinetySeven Thousand One Hundred FiftyThree Only

I we am / are willing to carry out the work at …................................ % above/ Below percent ( Should Be writen

in figures And words) of the estimated rate mentioned above. Amount of my / our tender works out as under.

Estimated Amount Put to tender. 11,97,153.00 Estimated Amount Put to tender.11,97,153.00

Deduct…........ % Below Deduct…........ % Below

In Words In Words

(1) The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge

for which no extra payment shall be made.

(2) The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

(3) GST and Income tax TDS will be deducted at a source while making payments of bills

(4) In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per

actual mix design the cost of difference of cement consumption have been deducted from the rate of original item at the rate

of input rate mentioned in all the tender.

Signature of Bidder

Deputy Executive Engineer Divisional Accountant

Panchayat ( R&B) Sub Division Panchayat ( R&B) Division

Dharampur Valsad

Executive Engineer

Panchayat ( R&B) Division

SHEDULE B Page