AIC/AED/NIeT-65(2nd Call)/26-27/Gr_1

Supply of octagonal shape 10/10.5 mtrs pole (BPP/Utkarsh/Galpol). Pole shaft shall be in two or single section, made from H.T. Steel of grade BSEN 10025,S355JO hot dip galvanised and suitable for wind Speed 18Okm/hr as per IS 875. It shall also included all panel mounting Suitable strctural encloser made by M.S angle arnd 40mmX40mmX3mm hallow square bar for arms of each panel prane including M.S double dram head frame one for installation Solar Panel and other for fixting Lighing fixture with G.I (16 SWG CRC Sheet) box for battery installation The Lighting Tower must have any of the following arrangement for future preventive maintenence of solar panel, light and batteries etc. i) Hand pully arrangement: If the system is arranged in the handpuly then winch with hand pully and the two continues steel wire Rope must be 4mm and Grade AISI 316, 7/19 . It have manual operating handle, , L-Staper.The mast shall have an intigral pwer tools installed inside the base compartment for its operation. ii) Metalic Ladder system: In this case the metalic ladder must be placed through the pole up to top from above 7/8 hight from the base of the pole. The pole alo have Lantern carrage arrangement suitable for 4 nos. luminaries symmetrically and its Battery box/light, Specification of the pole: Length-10/10.5m, Top dia. 150mm, Battom Dia. 340/310mm, 3.5mm thick. Specification of Foundation bolt-Dia. 24mm L-750mm, Number of bolt-4/6nos. Base plate 500mmX500mmX20mm

Installation, Commissioning with Erecion of High Mast Tower with all acc.( After fitting fixing panel frame, fitting all electrical equpments with the frame structure including making conn.)

Supplying and fixing 50W Luminaries comparise of : a) 50W, LED minimum colour temparature (CCT) 5500-6500 minimum typical luminous Lux 150Lm/W i.e minimum 3600 Lm (Philips/ Bajaj/Osram/ equivalent reputed make with BIS certificate) b) Charge controller with MPPT and effency>92% and it should have over charge protection, deep discharge protection, Batterys reversed polerty protection, Load short circuit protection, Open circut protection, panel revers polarity protection. Over temperature protection C) Automatic dusk to dawn controlling system to monitor the LED operation. a) With/ Withour Dimmer arrangement.Having warranty period 5 years. (IP 65 Protected Out door Flood light type fixture)

Supply, Transportation of ISI Marked as per IS 14286 and IEC61215, 61853 (1), 61730 (1&2), 617010 certified solar module of Mono PERC PV Module ( Panel to be supplied, Capacity 200Wp), The power output of the module under STC be maximum under load voltage l6.4 v +/- 0.2 V. The SPV module should not have power loss of not more than 20 % at the end ot 25 yrs.The module should be able to withstand temperature ranging from -10C to 80C, wind speed 180 km/hr, and humidity level up to 95%. (MAKE- HR SOLAR/ VIKRAM/ Waaree/or Any MNRE approved as per G.S). Strip must contain the following details a) Name of Manufacturer,b) Model or type number,c) Serial No,d) Year of make

Supply and commissioning of LiPo4 Battery. LITHIUM FERRO Batteries 12.8V, (95-100)AH. (The batteries having BIS Cerificate). The battary should have battery management system (BMS) with higher life expectancy, longer cycle life, low discharge rate and fast charging, Battery should provide 12 hr. backup. The battery must be provided with GI out door type battery box/Inbuilt in Luminaries. (MAKE- OKAYA/ Warree/ ARTECH ENERGY/ AMTEK EXIDE as per G.S) Battary must have 5 years warranty period.

Providing and makìng connection by 2 core 2.5sq PVC insulated and scheaded multistrand Cupper fexible cable(for making connection from solar pane to Battary and Lighting fixture(MAKE- MESCAB/POLYCAB/KEI)

Construcion of suitable shallow foundation with 1:2-4 or M20 grade concreate for the hight mast considaring the safe soil bearing capacity at site as 10T/sq. mtrs. At 1500mmX 1500mm X180Omm. including all materials, shuttering and lobour charge. (As per Given drawing) Foundation column should be 700mX 700mm.Foundation design may change according to site and soil condition

Sypplying, fixing & fixing display board or murblae Stone with suitable brick works as per G.S.

Comprehensive maintenance (At least three quarterly comprehensive maitenance should be done a year)

Sub Total