REPAIR TO CHARPOY GI AND IP HARD TOP AND MISC WORKS AT FCM OFFRS MESS, CGP AND GUEST HOUSES AT AFA HYDERABAD

Amount

Sofa sets FD 18/234 :

Labour for removing the existing worn-out/ unserviceable tapestry cloth and S & F new tapestry cloth (Tapestry cloth not less than Rs. 250/- per mtr) of approved quality and shade including refitting of shaky legs and bottom stiffeners for even level and provn of white coarse cloth at bottom of sofa chairs all as per drawing and as specified and directed for the following:-

Sofa Set chairs without arms FD - 18/234

Sofa set chairs with arms FD-18/234

S & F new cushion of 75mm thick 40D for seat all as directed . 18/234

(ii) S & F new cushion of 75mm thick 32D for back all as directed . FD-18/234

M & L for removing the existing broken or unserviceable legs of sofa set and S &F new legs of Ist class HW (Teak Wood) similar to removed one with PVC shoes including two coats of french polish to replaced leg and to old existing leg to match the original all as specified and directed. FD - 18/234

(i) Supply of new cushions of 100 mm thick of size 560x530x40 Density for seat of approved quality complete covered with white coarse cloth over that new tapestry cloth (tapestry cloth not less than Rs. 250/- per RM) of approved quality and shade duly stitched/with zip facility all as specified and directed FD-281/373

(ii) All as per item above but for back

M&L for removing the existing broken or unserviceable components of Sofas (FD-281/373), S&F New I st class hard wood (Teak Wood) including two coats of french polish to all replaced and old existing components complete and to match the original all as specified in drawings and as directed by Engineer-in-Charge :FD-281/373 (i) Arms made of 1st class hard wood (Teak wood)

(ii) Wooden battern of seat frame made of 1st class hard wood (Teak wood)

(iii) Wooden battern of back frame made of 1st class hard wood (Teak wood)

(iv) Front rail of seat of 3 Seater Sofa made of 1st class hard wood (Teak wood)

(v) Front rail of seat of single Seater Sofa made of 1st class hard wood (Teak wood)

Supply of new tapestry cloth cover for 100 mm thick cushions of size 560x530x40 Density for seat/back of approved quality with zip facility (tapestry cloth not less than Rs. 250/- per RM) of approved quality and shade duly stitched as specified and directed FD-281/373

Sofa chairs (SDF) Labour for removing the torned/deshaped foam & Cloth tapestry and cushion for seat and back of Sofa chair and S & F new cushion and rexine/cloth tapestry cover of approved quality to match the original complete all as specified and directed (tapestry cloth not less than Rs. 250/- per RM) FD-281/373

Bed plywood top FD - 213/246/247

(i) Labour for removing the existing broken or U/S long rails of bed plywood top and S&F new long rail of Ist class hard wood (Teak Wood) of size as shown in drgs including two coats of french polish to all replaced and old existing components complete to match the original all as specified and directed.

(ii) Labour for removing the existing broken or U/S Short rails of bed plywood top and S&F new Short Rail of Ist class hard wood (Teak Wood) of size as shown in drgs including two coats of french polish to all replaced and old existing components complete to match the original all as specified and directed.

(iii) Labour for removing the existing Unserviceable or wornout plywood top of bed and S&F new plywood top of suitable size 12 mm thick BWR grade and all as specified and directed.

(iv) Labour for removing the existing Unserviceable or wornout stiffner and S&F new II class hard wood stiffners of size 50x45x860 mm all as specified and directed.

(v) M & L for removing existing unserviceable Corner brackets and S&F new corner bracket made of MS Flat 50x 6mmx 150mm in L shape with three holes on each side all as directed

Removing the existing broken or U/s teak ply cover of head board/foot board of bed newar/Bed hard (Drg No.FD 213/212/245/246) and supply and fix new ply of 4 mm thick teak veneer face on one side all as shown in drawing and apply two coats of french polish to all replaced and old existing components and providing 6mm thick teak wood beading around head board/foot board complete to match the original all as specified and directed: (i) Head board inside

(ii) Head board outside

(iii) Foot board inside

(iv) Foot board outside

Bed Hard steel w/o MNF Set FD/E6/MAP/08 R

(i) M&L for welding with 20 x 45 x 3 mm MS Angle Iron cleat with holes to fix screws to support 18mm thick Particle Board including screws complete for Bed hard steel all as specified and as directed

(ii) M&L for removing unserviceable 18 mm thick prelaminated particle board with PVC edging from Head Board of Bed Hard Steel and S&F new 18 mm thick prelaminated particle board with PVC edging with suitable nut & bolt as specified

(iii) M&L for removing unserviceable 18 mm thick prelaminated particle board with PVC edging from Foot Board of Bed Hard Steel and S&F new 18 mm thick prelaminated particle board with PVC edging with suitable nut & bolt as specified

(iv) Labour for removing the existing Unserviceable or wornout plywood top of Bed Hard Steel and S&F new plywood top of suitable size 12 mm thick BWR Grade all as specified and directed.

(v) S&F 3mm thick PVC shoes to the legs of Bed Hard Steel

(vi) M & L for providing MS flat strip of size 70mm x 40mm x3mm with a bore of 10mm for nut and bolt (to be fixed in such a way that 20mm will be welded to headrest/footrest and 50mm will be welded to long rail of bed hard steel) to bind long rail and foot board/head board of bed hard steel duly welded and supported with suitable nut, bolt & washer and all as directed.

(vii) Scraping down old paint and applying putty to obtain even surfaces and applying two coats of synthetic enamel paint Black shade to Bed Hard all as specified and as directed.

Chair dining long back;- FD-357 Removing the old unserviceable components/parts from the Chairs and S&F new componets/part as to match with the existing for the following parts :-

(i) Front Legs (TW)

(ii) Rear Legs (TW)

(iii) Side rails (TW)

(iv) Corner brackets of size 65x65x25 mm (TW)

(v) S&F 50 mm cushion for seat of size 450x465 mm (24 D) covered with foam leather/Rexine of approved quality including 12 mm plywood and colour all as specified and directed

(vi) S&F 50 mm cushion for back of size 650x300 mm (24 D) covered with foam leather/Rexine of approved quality including 12 mm plywood and colour all as specified and directed

(vii) Back cover 4 mm ply including rexine cover as approved.

Hat stand with mirror ;- FD-206/233 Removing the old unserviceable components/parts from Hat Stand and S&F new componets/part as to match with the existing for the following parts :-

(i) Mirror of size 300x440mm with teakwood beading

(ii) 4mm thick Plywood of size 1000mm x 710 mm for front/back

(iii) Brass Peg Hooks

Book Case Steel :- FD-1028, 90 M

(i) Removing of existing dents and spot welding wherever required in Book Case steel and preparation of surfaces smooth for painting complete all as specified and as directed

(ii) Removing deshaped/unserviceable glass shutter and S&F new glass shutter made out of 20 guage MS Sheets as to match with the existing duly painted with two coats of paint over a coat of primer duly fixed with glass 3mm and lock complete all as specified and as directed.

(iii) Removing the u/s locks and S&F new lock of approved make and quality complete all as specified.

(iv) Labour for scrapping down the old painted steel surface for carrying out repairs and filling with putty to obtain even surfaces, applying primer to surfaces and applying two coats of synthetic enamel paint of approved make and shade complete all as specified and directed

Chair Easy cushioned;-FD-358 M&L for removing the existing broken or unserviceable components of Chair Easy Cushioned, S&F new components as to match with the original all as specified in drawings and as directed.

(i) Front Leg

(ii) Rear Leg

(iii) Side Rail of Seat

(iv) Front/Back Rail for Seat

(v) Arms

(vi) Labour for removing the existing worn-out/ unserviceable tapestry cloth/rexin, foam, etc from seat and back including cushioning on arms of chair easy cushioned and S & F new tapestry cloth (Tapestry cloth not less than Rs.250/- per mtr) of approved quality and shade) and synthetic foam of appropriate size all as specified and directed

Table bed side : - FD-248 M&L for removing the existing broken or unserviceable components of table bed side, S&F new components as to match with the original all as specified in drawings and as directed

(ii) Side

(iii) Bottom

(iv) Shelf

(v) Back

Book case Wooden :-FD-45, FD-237, FD-355 M&L for removing the existing broken or unserviceable components of Book case wooden, S&F new components as to match with the original all as specified in drawings and as directed.

(i) Top made of 18mm thick prelaminated particle board

(ii) Side made of 18mm thick prelaminated particle board

(iii) Bottom made of 18mm thick prelaminated particle board

(iv) Shelf made of 18mm thick prelaminated particle board

(v) Door shutter made of 18 mm Prelaminated particle board edges covered with 6mm thick TW beading fixed with CP knob and piano hinges.

(vi) Back made of 6mm thick Plywood commercial

(vii) CP Knobs

Chair Dining Officers:- FD/MAP-II/04 M&L for removing the existing broken or unserviceable components of Chair Dining Officers, S&F new components as to match with the original all as specified in drawings and as directed.

(i) Front Leg

(ii) Rear Leg

(iii) Side Rail of Seat

(iv) Front/Back Rail for Seat

(v) Back vertical Stiffners

(vi) Labour for removing the existing worn-out/ unserviceable fabric cloth, foam from seat and S & F new fabric cloth/cloth tapestry (Cloth not less than Rs.250/- per mtr and of approved quality and shade) and synthetic foam of appropriate size all as specified and directed

Rack shoe steel : - FD/MAP-II/02 R

(i) M&L for scraping down old painted surface and two coats of synthetic enamel paint Black shade to the frame complete all as specified and as directed.

(ii) M&L for Spot welding to bind the broken component of rack shoe steel complete all as specified and as directed.

Table dining 1200x900mm : - FD/ MAP-II/03 M&L for removing the existing broken or unserviceable components of Table dining 1200x900mm, S&F new components as to match with the original all as specified in drawings and as directed.

(i) Legs

(ii) Long Rails

(iii) Short Rails

(iv) Top made of 18mm prelaminated particle board

(v) S&F new corner bracket made of MS Flat 50x 6mmx 200mm in L shape with three holes on each side all as directed

Charpoy IP hard top ;- FD/MAP-II/01

(i) Removing existing unserviceable plywood top from Charpoy and S & F new 12 mm thick plywood BWR garde complete all as specified and shown on drawing

(ii) Removing existing unserviceable/broken MS Cleat to support Ply wood and S&F new MS cleat of size 25 x 60 x 6mm all as shown in drg and as directed.

(iii) M & L for providing MS flat strip of size 70mm x 40mm x3mm with a bore of 10mm for nut and bolt (to be fixed in such a way that 20mm will be welded to headrest/footrest and 50mm will be welded to long rail of bed hard steel) to bind long rail and foot board/head board of bed hard steel duly welded and supported with suitable nut, bolt & washer and all as directed.

(iv) Scraping down old paint and applying putty to obtain even surfaces and applying two coats of synthetic enamel paint Black shade to Charpoy IP Hard top complete all as specified and as directed.

(v) S&F 3mm thick PVC shoes to the legs of Charpoy IP Hard top

Charpoy GI Pipe FD - 220

(i) M&L for dismantling of GI pipe charpoy to carry out repairs like threading at ends of existing pipe removing the broken U/S legs, long rails, short rails, elbows and check nuts and fixing new elbows and check nuts and reassembeling the charpoy complete all as specified in the drgs. and as directed by Engineer-in-Charge. (Threading,Elbows and checknuts will be measuered & paid separately)

(ii) Threading of GI pipe 32 mm dia upto 25mm long

(iii) Supply 3 way elbow GI Pipe 32mm dia ISI Marked.

(iv) Supply GI check nut for GI Pipe 32mm dia ISI Marked.

(v) Supply 55mm dia 3mm thick rounds to be welded to legs of GI charpoy all as directed.

(vi) Supply 32 mm dia GI Pipe long rail both ends screwed including S&F new MS iron strips 02 Each of size 50mm x 6mm thick, 75mm long duly holed/drilled for tightening plywood and strip with countersunk screws/suitable nuts, bolts and washers and welded including two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed

(vii) S&F new MS Iron strips 02 Each of size 50mm x 6mm thick, 75mm long duly holed/drilled for tightening plywood and strip with countersunk screws/suitable nuts, bolts and washers and welded to 01 Each short rails retrieved from item (vi) above including two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed (Note : Threading of GI pipe 32 mm dia upto 25mm long will measured separately)

(viii) Cutting and threading at one end of 55mm dia 3mm thick round welded at another end of 01 Each leg retrieved from item (vii) above all as specified and directed. (Note : Threading of GI pipe 32 mm dia upto 25mm long and S&F of rounds will be measured separately)

(ix) Removing old unserviceable plywood top from charpoy GI and S & F 1950 x 900 mm x 12 mm thick BWR new ply wood confirming to IS 303 and fixed with suitable nut & bolt complete as specified and directed.

Mirror Wall 4'6" x 2'

(i) Removing existing broken/unserviceable mirror and S&F new mirror of size 1350 x 600mm to the frame all as specified and as directed

(ii) Removing existing unserviceable plywood back and S&F new 6mm plywood commercial back of size 1350 x 600mm all as specified and as directed

(iii) Removing existing unserviceable teak wood frame and S&F teak wood frame of even size and pattern where ever required all as specified

(iv) S&F new eye hook with 2 Nos 10mm screw for hanging the mirror to wall

S & F new top of 18 mm thick commercial ply board fixed with 1 mm thick plastic laminated sheet on top and 05 mm thick TW beading alround all as specified and as directed for the following

(i) Table 750 x 600mm

(ii) Table Dining 2400 x 1200mm

(iii) Table Dining 1600 x 1600mm

(iv) Table Class Room 900 x 600mm

(v) Table 900 x 900mm

M&L for removing the existing broken or unserviceable components of Chair Dining Officers, S&F new components as to match with the original all as specified in drawings and as directed.

Chair Dining FD/MAP-II/05 (JCO/ORs)

(i) Rear Legs Made of 1st Class hard wood (Teak Wood)

(ii) Front legs Made of 1st Class hard wood (Teak Wood)

(iii) Stiffners Made of 1st Class hard wood (Teak Wood)

(iv) Bend Stiffners for back rest Made of 1st Class hard wood (Teak Wood)

(v) Side rails Made of 1st Class hard wood (Teak Wood)

(vi) Wooden Corner brackets of size 65x65x25 mm

(vii) Removing old u/s PVC seat and S&F new PVC seat of approved quality as specifed and directed.

Chair Revolving /Executive/ Computer/Visitor with or w/o Arms PCH- 9101 R, FD/ E6/ MAP/01,FD/E6/MAP/01 (FD-TP)

(i)Labour for removing the unserviceable castor wheel and S & F new castor wheel to chair revolving/executive/computer to match with the original complete all as directed.

(ii)Labour for removing old height adjustment mechanism of chair revolving/executive/computer and S&F new height adjustment mechanism including greasing complete all as specified and directed by Engineer-in-Charge.

(iii)Labour for removing the torned/deshaped leather/ cloth tapestry for seat and back of chair revolving high back /executive/computer/visitor and S & F new rexine/cloth tapestry cover of approved quality to match the original complete all as specified and directed.

(iv)Labour for removing the torned/deshaped leather/ cloth tapestry and foam cushion for seat and back of chair revolving high back /executive /computer/visitor and S & F new cushion and rexine/cloth tapestry cover of approved quality to match the original complete all as specified and directed.

(v)Labour for removing unserviceable hydraulic gas lib and S & F new hydraulic gas lib to chair revolving /executive/computer to match the original complete all as specified and as directed.

(vi)Labour for removing unserviceable wheel base and S & F new wheel base steel 5 arms to chair revolving /executive/computer to match the original complete all as specified and as directed.

(vii)Labour for removing unserviceable wheel base and S & F new PVC wheel base with 5 arms to chair revolving /executive/computer to match the original complete all as specified anbd as directed.

(viii)Labour for removing old/broken handles and S & F new handles complete in pairs for chair revolving /executive/computer/visitor to match the original complete all as specified and as directed.

(ix)Dry cleaning of Sofa sets/Chair revolving/Computer/Executive/Visitor with chemical wash after necessary dry vaccum cleaning complete all as specified and as directed.

Auditorium Chair with Push Back Mechanism. Make : Innovative (TP) (i)Labour for removing broken/unserviceable armrest of chair and S&F new armrest as to match with the existing all as specified and directed

(ii)Labour for removing the torned/worned out upholstery for seat of chair and S & F new cover made of cloth tapestry cushioned and rexin of approved quality as to match the original complete all as specified and directed.

(iii)Labour for removing the torned/worned out upholstery for back of chair and S & F new cover made of cloth tapestry cushioned and rexin of approved quality as to match the original complete all as specified and directed.

(iv)Removing the existing unserviceable PVC Cap and S&F new PVC cap as to match with the existing all as specified.

(v)M & L and labour for tightening of Push Back Mechanism of chair auditorium all as specified and directed by Engineer-in-Charge

(vi)Labour for removing unserviceable Push Back Mechanism and S&F new push back mechanism of superior quality as to match with the existing all as specified and directed

(vii)Labour for removing unserviceable PVC Back cover and S&F new PVC back cover of superior quality as to match with the existing all as specified and directed

(viii)Labour for removing unserviceable PVC Seat cover and S&F new PVC seat cover of superior quality as to match with the existing all as specified and directed

Labour for removing the U/S worn out broken cane of chair verandah and recanning with new plastic cane of 3mm wide of approved make complete all as specified and directed.

Labour for scrapping down the old painted steel surface for carrying out repairs and filling with putty to obtain even surfaces duly applying surfaces and applying two coats of synthetic enamel paint of approved shade by spray machine all as specified and directed for the following : (i)Chair verandah

(ii)Book case large steel

Labour for cleaning and preparation of old treated wooden surfaces of any description and applying two coats of french polish for the following wooden furniture all as shown in drgs and as directed. (Including polishing at site.)

(i) Bed plywood top FD - 213/246/247

(ii) Chair dining long back FD - 357

(iii) Table writing FD - 33/275

(iv)) Hat stand FD-206/233/362

(v) Chair Easy Cushioned FD-358

(vi) Chair Dining Officers FD/MAP-II/04

(vii) Table dining 1200x900 FD/MAP-II/03

(viii) Table Class Room 900 x 600mm

(ix) Wall Mirror 4'6" x 2"

(x) Sofa set 4 seater FD-281/373

(xi) Sofa set 5 seater FD - 281/373/FD/MAP-II/02

(xii) Book case

(xiii) Chair Dining JCO/ORs FD/MAP-II/05

Mahesh Traders (BID ID -3363093)

A.K. MARKETING ASSOCIATES (BID ID -3371857)

Global Enterprises (BID ID -3361500)