Conversion of 11KV HTover head line into underground 2 run 11KV HT cable from substation No.1(near store office)to substation No.2(near tower No.3)and from substation No.3(near tower no17) to substation No4(near tower no. 12)inside EDK atOFK

Excavating in trenches not exceeding 0.50 m wide and 1.0m depth for HT cables and getting it out in hard/dense soil for laying of U/G cable. Complete all as specified & directed. Note: Digging by JCBs are not allowed.

Sand cushioning in cable trenches 20 cm thick for HT cable including material & labour.

Supplying & laying un-reinforced precast concrete cable cover class HV type 1 peak size 300mmx180mmx40mm with identification of cable cover with material & labour.

Returning filling in, including spreading,levelling,watering and well ramming in layers not exceeding 25 cm.

GI pipe medium grade 80mm dia with all fittings and fixed completely to poles & laid in trenches with material & labour.

Demolition & dismantling Cement concrete in ground floors & pavings not exceeding 15 cm thick below or above ground level.

M&L PCC Type B2, mixed by volume 1:2:4 with 40 mm normal size graded coarse aggregate.

M&L Reinforced cement concrete (Design mix) of type M- 20, 1:1½:3 (20mm graded aggregate) in foundations, footings, under reamed piles etc. conforming to quantitative analysis report of the materials to be submitted by the contractor before execution of concretting work.

M&L Reinforced cement concrete columns, pillars, plers (Design mix) of type M- 20, 1:1½:3 (20mm graded aggregate) conforming to quantitative analysis report of the materials to be submitted by the contractor before execution of concretting work.

Mild steel TMT bars 10 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not lass than 0.9 mm dia or securing with clips. Complete all as specified & directed.

Mild steel TMT bars 6mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not lass than 0.9 mm dia or securing with clips. Complete all as specified & directed.

M&L Reinforced cement concrete (Design mix) of type M- 20, 1:1½:3 (20mm graded aggregate) in beams, lintels over 1.5m span. conforming to quantitative analysis report of the materials to be submitted by the contractor before execution of concretting work.

S&F Prestressed concrete pole, 11.0 metres long. 152mm x 152mm at top and 152mm x 260mm at bottom, class 9, with material and labour.

Danger Notice plate of 1.6 mm thick mild steel sheet vitreous enamelled white with letters,figures and conventional skull and bones in signal red colour and fixed with M.S.clamps, bolts and nuts of approved size for HT 25x20 cm size as per IS 2551 with material & labour.

Supply & fixing cross arm of MS channel bracings,supports,clamps and back plates fabricated from structural steel section including nuts & bolts, washers,welding,bending, cold or hot, drilling holes for bolts in any shape or size as indicated or directed & inclusive of one primer coat, one under coat & one finishing coat of paint with material & labour. Note:- Required for fixing of AB switch, L.A., clamping of GI pipe on pole etc.

Dismatling cross arm of MS channels or angle section etc complete and setting aside for reuse.

Dismantling insulator any type any size.

Dismantling of ACSR or AAC conductors

S & L of XLPE insulated screened PVC bedded galvanized steel strip or wire armoured, electric power cable (Heavy duty) with aluminium conductor 11000 Volt grade size 95 Sq.mm 3 core including termination of both the ends with proper lugs with labour. Make of cable: Unistar/Finolax/Havells/Sterlite/KEI/V-guard/Polycab or equivalent. Note:- cable should be joint free.

Dismantled/scrap Aluminium conductor. (CREDIT ITEM).

Structural steel scrap (ms Cross arms, ms channels, ms angles etc.) (CREDIT ITEM).