Balance work for Construction of PWD Sub-Division office combined with Treasury office building at Balichowki in Tehsil Balichowki Distt. Mandi SH C/o building portion with WS SI in ground floor and 1st floor

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of classfication of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering and other incidentials lifts upto any height, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying cement concrete work 1:2:4 (one cement : two sand : four graded crushed stone aggregate 20mm (twenty millimetre) nominal size mechanical mixed and curing complete excluding cost of form work and reinforcement for reinforced concrete work in. suspended floor roofs .landings and shelves and their support balconies beams ,girders,bressumers and cantilver upto all floor level including carriage of materials with in all leads, lifts and other incidentals .

column,pillars posts and struts upto all floor level including carriage of materials with in all leads, lifts and other incidentals .

Stair cases (except spiral stair cases) excluding landing but including preparing of the top surface and finishing of nosing upto all floor level including carriage of materials with in all leads, lifts and other incidentals .

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting and removal of same for insitu reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. flat surfaces such as soffits of suspended floors,roofs, landings and the like floors etc. upto any thickness.

Columns, pillars, posts and struts in square, rectangular or polygonal in plan.

Edges of slabs and breaks in floors and walls of in any width.

vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 Graded stone aggregate 25mm (twenty five millimetre) nominal size and curing complete excluding cost of form work in foundation and plinth in breast and retaining walls etc. including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire complete in all floors including carriage of materials with in all leads, lifts and other incidentals.as per the directions entire satisfaction of Engineer-in-Charge

Stone filling tightly dry hand packed under floors, including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Stone filling behind retaining walls including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge

Providing and laying cement concrete 1:2:4 (1 cement:2 sand :4 graded stone aggregate 40mm (fourty millimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge. Providing and laying cement concrete 1:2:4 (1 cement:2 sand :4 graded stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of fram work and reinforcement for reinforced concrete work in.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc. from top of foundation upto floor any level.

Providing and laying precast concrete block masonry ( including quion blocks jamb blocks closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 ( 1 cement : 3 sand : 6 graded stone aggregate 40 mm (forty millimetre) and down gauge ) foundation and plinth upto floor all level in cement mortar 1:6 ( 1 cement : 6 sand ) including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and laying precast concrete block masonry in partition walls 10cm (ten centimetre) thick with solid blocks of approved size ) inlcuding quion blocks jamb blocks, closer etc. made of cement concrete 1:3:6 ( 1 cement : 3 sand : 6 graded stone aggregate 40mm (forty millimetre) and down gaugein super structure upto floor all level in in cement mortar 1:6 ( 1 cement : 6 sand) including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing 2nd class deodar wood work in frames of false ceiling partitions etc. sawn and put-up in postion including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Providing and fixing 1st class Deodar wood 12mm (twelve millimetre) thick 150mm (one hundred fifty millimetre) wide pelmet with 25 mm (twenty five millimetre) diametre wooden curtain rods and brackets including fixing 25x3mm (twenty five into three millimetre) M.S. flat at 10 cm (ten centimetre) Long and plugs etc. complete including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Providing and fixing brass curtain rail with rollers stop ends and brackets in pelmets instead of wooden curtain rod 25 mm (twenty five millimetre) dia and brackets of first class deodar wood (actuallenght) of rails of be measured including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Providing and laying Brick work using common burnt clay building bricks in foundation and plinth in including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in Cement Mortar 1:5 (1 cement:5 sand) including curing complete and carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Providing and fixing 300x16mm (three hundred sixteen millimetre) anodized aluminium sliding door bolts with nuts and screws etc. complete including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge.

Providing and fixing aluminium tower bolts (berrel type) anodized transporent trans parent or dyed to required shade and colour with screws etc. complete including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer- in -charge. 250x10mm (two hundred fifty into ten millimetre)

200x10 mm (two hundred into ten millimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge. 100 mm (one hundred millimetre)

125 mm (one hundred twenty five millimetre)

Providing and fixing 2nd class deodar wood work in frames of doors, windows ,clerestory ,windows and other frames wrought,framed and fixed in position. including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing 40mm (fourty millimetre) thick 2nd class deodar wood panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing 40x3 mm (fourty into three millimetre) flat iron hold fast 40 cm (fourty centimetre) long including fixing to frame with 10mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 mix ( 1 cement :3 sand : 6 graded stone aggregate 20 mm (twenty millimetre) nominal size including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying Kota stone slab flooring 30 mm (thirty millimetre) (average) thick laid over 12 mm (tweleve mm) base of cement mortor 1:4 (One cement : Four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab rubbing and polishing complete including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and laying Kota stone slab flooring 25 mm (twenty five millimetre) thick riser or steps, skirting dedo and pillar laid over 12 mm base of cement mortor 1:3 (One cement : Three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab rubbing and polishing complete including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick in flooring 300 x300mm (three hundred into three hundred millimetre) size treads of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3(1cement: 3 sand) finished with flush pointing in white cement including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying White glazed tiles 6 mm (six millimetre) thick in skirting risers of steps and dado 12 mm (twelve millimetre) thick cement mortar 1:3 (One cement : Three sand) and jointed with cement slurry including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and laying Precast terrazzo tiles hydraulic compressed 20 mm (twenty millimetre) thick with marble chips of specified sizes laid in floors, treads of steps and landing on a bed of 25mm (twenty five millimetre) average thickness of cement mortar 1:6 ( 1 cement : 6 sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of white shades including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and laying Precast terrazzo tiles hydraulic compressed 20 mm (twenty millimetre) thick (with marble chips of specified sizes) in skirting and risers of steps in 30cm (thirty millimetre) in height on 10mm (ten millimetre) thick cement plaster 1:3 (1 cement: 3 sand)jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of white shaded including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing 2nd class indian teak wood 75 mm x 60mm (seventy five millimetre into sixty millimetre) rounded hand rails in straight length complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing 2nd class indian teak wood 25mm + 25mm (twenty five millimetre + twenty five millimetre) balusters 25mmx25mm (twenty five millimetre into twenty five millimetre) square wrought fixed with ends housed (square or splay) to hand rails and treads or strings complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Cement concrete flooring 1:2:4 (One cement : Two sand : Four graded stone aggregate 40 mm (forty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement mm thick including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing and fixing 40 mm (fourty millimetre) thick plain framed panelling with necessary screws priming coat on unexposed surface etc. complete with 2nd class Indian teak wood including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Providing and fixing 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing and chajjas with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet and rubber washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six millimetre) dia & prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing valley 60cm (sixty centimetre) overall 0.60mm (zero point sixty millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia with prepainted G.I. limpet and bitumen washers complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing on wall face 150mm (One hundred fifty millimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm (Four point five kilogram per square metre) including filling the joint with approved adhersive complete including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete including curing of materials within all leads, lifts and other incidentals and as per direction Engineer in charge. PVC Plain Bend 150mm(One hundred fifty milimetre) dia.

PVC Shoe 150mm (One hundred fifty milimetre) dia.

Providing and fixing 15 cm (fifteen centimetre) wide 45 cm (fourty five centimetre) overall semicircular plain G.I. sheetgutter with iron brackets 40x3mm (fourty into three millimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design 0.63 mm (zero point sixty three millimetre) thick sheet including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in position and applying a priming coat of red lead paint in including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters,purlins connected to common rafters and the like.

In trusses and trussed purlins in building.

In rolled steel joists with or without stiffeners in grillage (the weight of stiffeners shall be added to the weight of joists.

Providing and fixing Garsa stone 12mm (twelve millimetre) cladding on R.C.C. surface side as on faces of Arch masonry walls etc. on 12mm (twelve millimetre) thick cement plaster 1:3 (1 cement : 3 sand) and jointed with cement slurry including scaffolding etc. complete including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

15mm (fifteen millimetre) Cement plaster in single coat on the rough side of brick/ concrete/ stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth Cement Mortar 1:5 (1Cement:5 Sand) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

20mm (twenty millimetre) Cement plaster in two coats, backing coat 15 mm (fifteen millimetre) and finishing coat 5mm (five millimetre) thick on rough side of brick/stone masonry for interior plastering including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in Cement mortar 1:6 (1 Cement : 6 Sand) upto floor all level including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with Readymixed paint brushing wood primer pink including carriage of material with in all leads and lifts and other incidentals and as per direction of Engineer-In-Charge.

Painting two coats (excluding priming coat)on new wood and wood based surfaces,with readymixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping with white paint including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Distempering with dry distemper of approved brand and manufacture(Two coats)and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

White washing with lime on undecorated wall surfaces two coats to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface including carriage of material with in all leads and lifts and other incidentals and as per direction Engineer-In-Charge.

Providing plinth protection 50mm (Fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three sand : six Graded stone aggregated 20mm (Twenty millimetre) nominal size) mechanically mixd and finishing surface of concrete smooth including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two centimetre) in cement mortor 1:6 (one cement: six sand) and in side blastering with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4 (one cement :two sand :four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge.

Providing and laying in trenches, galvanized mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) including carriage of materials with in all leads, lifts and other incidentals as per the directions of Engineer-in-Charge. 20mm (Twenty Millimetre) nominal bore

15mm (fifteen Millimetre) nominal bore

Providing and fixing sand cast / cast iron spun spigot and socket soil, waste and ventilating pipes (Lead caulked joints to be measured and paid for separately including carriage of material and other incidentials in all leads and lifts and as per the direction of Engineer-in-Charge. 100 mm (hundred millimetre) nominal size

75 mm (seventy five millimetre) nominal size

Providing and fixing cast iron holder bats including steel bolt to sand cast iron pipes embeded in and including cement concrete block 100x100x100mm (hundred into hundred into hundred millimetre) of 1:2:4 ( one cement: 2sand:4 concrete) including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 100 mm (hundred millimetre) nominal size

75mm (seventy five millimetre) nominal size

Providing and fixing sand cast iron/cast iron spun fittings and accessories Bends of required degree (any radius) With oval access door insertion rubber washer 2mm (two millimetre) thick, bolts and nuts complete including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 100mm (one hundred millimetre) nominal size

75mm (seventy five millimetre) nominal size

(plain bends) 100mm (one hundred millimetre) nominal size

75mm (seventy five millimetre) nominal size

Off sets 100mm (one hundred millimetre) Projection

75mm (seventy five millimetre) Projection

Single equal branch of required degree with oval access door insertion rubber washer 3mm (three milimetre) thick bolts and nuts complete. 75mm (seventy five millimetre) nominal size

100mm (one hundred millimetre) nominal size

Double equal branch of required degree with oval access door insertion rubber washer 3mm (three milimetre) thick bolts and nuts complete. Collar 75 mm (seventy five millimetre) nominal size

100mm (one hundred millimetre) nominal size

Providing lead caulked joints to sand cast/cast iron (spun) iron pipes fittings including testing of joints complete including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 100mm (one hundred millimetre) nominal size

75mm (seventy five millimetre) nominal size

Providing and fixing M.S. stay and clamps for sand cast iron / cast (spun) iron pipes including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 100mm (one hundred millimetre) nominal size

75mm (seventy five millimetre) nominal size

Providing and fixing cast iron floor trap of self cleaning desion with sand cast iron screwed down or hinged grating with out vent arn complete including cost of cutting and making goods the walls and floors including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 75mm (seventy five millimetre) nominal size

100mm (hundred millimetre) nominal size

Providing and fixing Orrissa Pattern vitreous China wash down,water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing Sand Cast iron 100mm (hundred millimetre) size 'P' or 'S' trap for water closet ( squatting pan)including jointing the trap with the pan and soil pipe in cement mortar 1:1(1 cement : 1 sand) including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing 10.0/12.50/15.00 litres vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15mm (fifteen millimetre) nominal size brass ball valve with polygthene float, C.P. Brass handle, unions and couplings for connections with inlet, outlet and overflow pipes, 40mm (fourty millimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush beng with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of marterial with in all leads, lifts other incidentals as per directions of Engineer-in-Charge.

Providing and fixing in position brass mosquito proof coupling for over flow pipe of 25mm (twenty five millimetre) nominal dia (over flow pipe to be measured and paid for separatey) including carriage of marterial and incidentials with in all leads, lifts as per directions of the Engineer-in-Charge.

Providing and fixing G.I. Inlet connection for flush pipe with W.C.Pan including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing Flat back type of size 430mm x 260mm x 350mm (four hundred thirty millimetre into two hundred sixty millimetre into three hundred fifty millimetre) vitreous China bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with choppe hemp (weste pipe to be measured and paid for separately) including carriage of marterial and incidentials in all leads, lifts as per directions of Engineer-in-Charge.

Providing and fixing Vitreous China 5 (five) litres capacity automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) including carriage of marterial and incidentials in all leads, lifts and as per directions of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) nominal bore C.P. brass flush pipe/spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing Flat back 550mmx400mm (five hundred fifty millimetre into four hundred millimetre) vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of marterial and incidentials in all leads and lifts as per directions of Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) dia C.P. Brass chain 50cm (fifty centimetre) long and rubber plug for sink or wash basin including carriage of marterial and incidentials in all leads and lifts as per directions of Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) dia rubber plug for sink / wash basin including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) dia C.P. Brass waste for wash basin or sink including carriage of marterial and incidentials in all leads and lifts as per directions of Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) dia M.I. Union for wash basin or sink including carriage of marterial and incidentials in all leads and lifts as per directions of Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) dia C.P. Brass S. Trap for wash basin and sink including carriage of marterial and incidentials in all leads and lifts as per directions of Engineer-in-Charge.

Providing and fixing 32 mm (thirty two millimetre) dia waste pipe for wash basin and sink including carriage of marterial and incidentials in all leads, lifts and as per directions of Engineer-in-Charge.

Providing and fixing 600mm x 450mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge miror of superior glass mounted on 6mm (six millimetre) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P brass 600 mm x 20 mm (six hundred millimetre into twenty millimetre) complete including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing 600 mm x 120 mm (six hundred millimetre into one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws complete including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing 600mm x 450 x 150 mm (six hundred millimetre into four hundred fifty into one hundred fifty millimetre) kitchen sink with C.I. Or M.S brackets, painted white including cutting holes in walls and making good the same but excluding fittings complete including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia c.p brass bib tap with capstan head including carriage of marterial and incidentials in all leads and lifts as per directions of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) dia c.p brass pillar tap with capstan head including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) brass stop cock including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) nominal bore C.P. connection pipe with brass unions 30 cms (thirty centimetre) length including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing brass full way valve with wheel including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge. 20mm (twenty millimetre) nominal bore

15 mm (fifteen millimetre) nominal bore

Providing and fixing G.I/M.I. Union following size ( where not including in the items ) including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge. 15mm (fifteen millimetre) dia

20mm (twenty millimetre) dia

Providing and fixing G.I sockets including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge. 15mm (fifteen millimetre) dia

20mm (twenty millimetre) dia

Providing and fixing G.I Tees (equal) including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge. 15mm (fifteen millimetre) dia

20mm (twenty millimetre) dia

Providing and fixing (Vitreous China) Recessed soap tray 150mm x 150 mm (one hundred fifty millimetre into one hundred fifty millimetre) size including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing Tooth brush and Tumbler holder (Vitreous China) including carriage of marterial and incidentials in all leads, lifts and as per directions of the Engineer-in-Charge.

Providing and fixing 100mm (hundred millimetre) sand cast iron grating for gully, floor or Nahni trap including carriage of marterial and incidentials in all leads, lifts and as per directions of Engineer-in-Charge.

Providing and fixing 2000 ltr. PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Constructing manhole with RCC top slab in 1:2:4 mix in (1 cement : 2 sand : 4 graded stone aggregate 20mm (twenty millimetre) nominal size foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm (fourty millimetre) nominal size inside plastering 15mm (fifteen millimetre) thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm (twenty millimetre) nominal size) finished smooth complete including curing and testing Inside size 800mm x 800mm (eight hundred millimetre into eight hundred millimetre) and 500mm (five hundred millimetre) deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38kg (thirty eight kilogram)(Weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram)with 300mm (three hundred millimetre) thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (1cement 3 sand) complete including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Supplying cast iron cover without frame for manholes For frame of internal dimension 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) rectangular C.I. Cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg (twenty three kilogram) including carriage of marterial and incidentials in all leads, lifts and as per directions of Engineer-in-Charge.

Filling with brick 50 mm (fifty millimetre) nominal size aggregate in soak pit complete including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing Cast iron cowl 100mm (hundred millimetre) nominal diameter including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying in trenches 10 kg / cm2 (ten kilogram per centimetre) working pressure unplasterized PVC pipes (conforming to I.S complete with fitting) earth work in trenches to be measured and paid separately with outside diametre) including carriage of marterial and incidentials in all leads and lifts as per directions of the Engineer-in-Charge.

LEKH RAJ