WELCOME MAINTENANCE AND REPAIR TO JOINERY, PLUMBING, SANITARY FITTING, SUNKEN TREATMENT ETC AT SECTOR-31 A AND D UNDER GE (AF) CHANDIGARH

Amount

Material & labour for Preparation of old surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white wash, complete all as specified and directed by Engineer-in-Charge.

Material & labour for Preparation of old surfaces of ceiling including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white wash, complete all as specified and directed by Engineer –in-Charge.

Material & labour for Preparation of old surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc.; rubbing down and stopping of surfaces using sand paper and applying one coat of oil bound distemper, complete all as specified and directed by the Engineer-in-Charge.

Material & labour for Prepartation of old painted wooden surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed by the Engineer-in-Charge.

Material & labour for Prepartation of old painted steel or iron surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed by the Engineer-in-Charge.

Demolition of lime concrete/ lean concrete/ brick bats from sunken portion exc. 15 cm thickness (above ground level), including removal of rubbish outside MoD land,complete all as specified and directed by the Engineer-in-Charge.

Material & labour for Water proofing treatment to sunken portion of WCs, bathroom etc. by applying cement slurry mixed with Acrylic based polymer modified cementitious composite compound coating of make as approved by GE:- (a) 15 mm thick plaster (1:4) in cement sand mortar with integral water proofing compound 2 % by weight of cement on floor and wall, finishing the surfaces even and smooth without using extra cement. The surface shall then be cured and allowed to dry. (Note: Supply only water proofing compound shall be measured and paid separately). (b) First layer of slurry of cement @ 0.488 Kg/Sq.m mixed with Acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sq.m. This layer will be allowed to air cure for 4 hrs. (c) Second layer of slurry of cement @ 0.242 Kg/Sq.m mixed with Acrylic based polymer modified cementitious composite compound @ 0.126 Kg/Sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

Material & labour for PCC (1:2:4), type B-1, using 20 mm graded mechanically crushed stone aggregates, using integral water proofing compound @ 3% by weight of cement, as in padding concrete to sunken floor, covering to junction of floor and vertical walls including chamfering on edges, complete all as specified and directed by Engineer - in -Charge. Note: Supply only water proofing compound shall be measured and paid separately

Supply only integral water proofing compound, complete all as specified.

Supply & fixing Steel water tubes, 40 mm bore, medium grade, galvanized, as in spout for sunken floor, fixed in wall, inside end fixed with wire netting and external beveled edge at 45 degree, complete all as specified and directed by Engineer - in -Charge.

Material & labour for Lean concrete (1:5:10), type E-2, using 40 mm brick coarse aggregate, as in sunken portion, complete all as specified and directed by Engineer - in -Charge.

Taking up or down 15 mm bore steel tubing with connections or fittings from wall, ceiling, floor etc.,including cleaning for refixing or removing from site , complete all as specified and directed by Engineer - in -Charge.

Taking up or down 20 mm bore steel tubing with connections or fittings from wall, ceiling, floor etc.including cleaning for refixing or removing from site , complete all as specified and directed by Engineer - in -Charge.

Supply & fixing 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed by Engineer - in -Charge. Note : Cutting chases as required shall be measured and paid seperately.

All as per srl item No 14 here in before but except pipe or G I tubing (serviceable pipes/GI tubing as obtained from Srl item No 12 shall be used, the rate includes for cleaning of pipe also).

Supply & fixing 20 mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed by Engineer - in -Charge. Note : Cutting chases as required shall be measured and paid seperately.

All as per srl item No 16 here in before but except pipe or G I tubing (serviceable pipes/GI tubing as obtained from Srl item No 13 shall be used, the rate includes for cleaning of pipe also).

Material & labour for Cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth in brick walls , complete all as specified and directed by Engineer - in -Charge.

Material & labour for Cutting holes into or through brick walls built in cement or cement lime mortar and making good disturbed portion in cement mortar (1:3) or cement concrete (1:2:4), type B-l (using crushed stone aggregate) as required , Superficial area exceeding 150 sqcm but not exceeding 400sqcm , complete all as specified and directed by Engineer - in -Charge.

Demolition of cement concrete (unreinforced) of any description including cast-in-situ terrazzo (below or above ground level), not exc. 15 cm thickness, including removal of rubbish outside MoD land, complete all as specified and directed by Engineer - in -Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises,complete all as specified and directed by Engineer - in -Charge.

Material & labour for 25 mm thick, PCC (1:2:4), type B-0 (12.5mm graded crushed stone aggregate) as in flooring finished even & rough to receive the bedding mortar of tiles etc.,complete all as specified and directed by Engineer - in -Charge.

Material & labour for First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed by Engineer - in -Charge.

Material & labour for First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sq.m but not exceeding 0.11 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed by Engineer - in -Charge.

Material & labour for First quality, glazed ceramic coloured tiles, 6-7mm thick of size 450mmx350mm fixed in pattern of different colour tiles including border of dark shade tiles, in skirting, dado with set and jointed in neat cement slurry, over and including 10 mm thick rendering of cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified.

Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified and directed by Engineer - in -Charge.

Material & labour for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished even and fair, complete all as specified and directed by Engineer - in -Charge.(Note :- The work is rquired to be executed in G+2 storey building , the rates include for scaffolding etc )

Material & labour for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified and directed by Engineer - in -Charge.

Material & labour for Rendering10 mm thick in cement mortar 1:3 on concrete surfaces or ceiling surfaces and finishing the surfaces even and smooth without using extra cement ,complete all as specified and directed by Engineer - in -Charge.

Material & labour for Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed by Engineer - in -Charge. Note: The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required up to 3.50 Mtr height building.

Material & labour for Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified and directed by Engineer - in -Charge. Note: The rate quoted by contractor is deemed to be included necessary scaffolding and form work as required exceeding 3.5 Mtr but n.exc 10 Mtr height building.

Supply and fixing , in repair , water closet (squatt pattern) including foot rest , vitreous china (white) ,first quality water closet, Orissa pattern size 580x440mm with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet , complete including fixing of flush pipe with seat and making good the disturbed floor surfaces to match with existing and making connections serviceable complete all as specified and directed by Engineer -in-Charge.

Supply and fix in repair , PVC low level, white, flushing cistern, valve-less, symphonic action type, 10 litres capacity with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connection to water supply pipe line and WC, complete all as specified and directed by Engineer -in-Charge.

Supply and fix in repair bib taps, long body with flange ,cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule, complete all as specified and directed . Make : CAT No 8608 of Prayag or equivalent in ESS ESS, MARC, Hindware

Supply and fix in repair ,Pillar taps, long neck ,cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe , complete all as specified and directed . Make : CAT No 8604 of Prayag or equivalent in ESS ESS, MARC, Hindware

Supply and fix in repair Angle stop valves with flange , cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule , complete all as specified and directed . Make : CAT No 8610 of Prayag or equivalent in ESS ESS, MARC, Hindware

Supply and fix Concealed stop cock regular body with flange, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, screwed for 15mm bore iron pipe or for unions fixed in repairs, complete all as specified. Make : CAT No 8618 of Prayag or equivalent in ESS ESS, MARC, Hindware

Supply and fix Central hole basin mixer with regular spout without popup waste system with 450 mm long braided hoses, cast copper alloy, chromium plated, screwed down for iron pipe 15 mm bore, fixed in repair, complete all as specified and directed. Make : CAT No 8650 of Prayag or equivalent in ESS ESS, MARC, Hindware

Supply and fix PVC connections of PTMT, non corrosive, with nuts & washers on both ends, 450 mm longs suitable for 15 mm bore, ISI marked, fixed in repairs, complete all as specified and directed by Engineer - in -Charge.

Supply and fix in repairs grating doom 125mm dia with waste hole of CP, complete all as specified and directed.complete all as specified and directed by Engineer - in -Charge.

Supply and fix in repairs soap dish brass, chromium plated fancy type fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer - in -Charge.

Supply and fix in repairs Wash basins, vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets, complete all as specified and directed by Engineer - in -Charge.

Supply and fix PVC flexible pipe suitable for WHB/ Sink/ Urinal, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Dismantling PVC water storage tank of capacity exceeding 250 litre but not exceeding 500 litre and stacking for issuing under credit, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing/hoisting, rotational moulded polyethylene (HDPE) water storage tanks (cylindrical vertical with closed top), 500 litres capacity ‘triple layered’, white colour with screwable lid, hoisted and fixed in position including inlet, outlet and drain pipe with plug, complete all as specified and directed by Engineer-in-Charge.

Supply and fix Ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, ISI marked (Minimum weight 210 gms), screwed & suitable for iron pipe 20 mm bore, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply and fix Stop valve of PTMT, 15 mm bore, any colour high pressure screwed for iron pipe (Minimum weight 90 gms), fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply and fix Stop valve of PTMT, 20 mm bore, any colour high pressure screwed for iron pipe (Minimum weight 92 gms), fixed in repairs, complete all as specified.

Taking down cast iron, soil, waste and vent pipes in any position including fittings (75/100mm dia), including cleaning for re-fixing or removal to store or for credit, complete all as specified and directed.

Material and labour for 75mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, fixed to wall with and including mild steel clamps and bolts with washers, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

Material and labour for 75mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, laid in trenches or in floors including necessary excavation and earth work, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

Material and labour for 100mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, fixed to wall with and including mild steel clamps and bolts with washers, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

Material and labour for 100mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, laid in trenches or in floors including necessary excavation and earth work, complete all as specified and directed. Note : Extra over for lead joints shall be measured and paid separately.

S & F in repairs cast iron bends 75mm bore, diminishing pieces or tapers ISI marked complete all as specified and directed by Engineer-in-Charge.

S & F in repairs cast iron bends 100 mm bore, diminishing pieces or tapers ISI marked complete all as specified and directed by Engineer-in-Charge.

S & F in repairs cast iron 75mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed by Engineer-in-Charge.

S & F in repairs cast iron 75mm bore branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed by Engineer-in-Charge.

S & F in repairs cast iron 100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 100mm bore branch pieces, double(equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brances with oval access doors complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Cast iron floor trap 75 mm dia out let, ISI marked, with CP grating including jointing to waste pipe in run lead & fixed in PCC (1:2:4), type B-1, complete all as specified and directed by Engineer-in-Charge.

Materials and labour, extra over for lead joints provided in lieu of cement joints for 75mm dia cast iron pipes and fittings, complete all as specified and directed by Engineer-in-Charge.

Materials and labour, extra over for lead joints provided in lieu of cement joints for 100mm dia cast iron pipes and fittings,complete all as specified and directed by Engineer-in-Charge.

Supply & Fix Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass chromium plated, fixed to walls with screws and plastic cleats, fixed in repairs, complete all as specified and directed by Engineer-in-Charge. Make :ESS ESS / MARC /PRAYAG

S & F in repairs stainless steel sinks with drainage board , ISI marked ,made out of 1.00 mm thick sheet for kitchen with plugs, washers, waste pipes, including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm with bowl size 410mm x 330mm x 160mm, with and including PVC waste pipe and CP waste coupling 32 mm dia and making good to disturbed surfaces, complete all as specified and directed.

Disconnecting existing tanks of capacity not exceeding 500 ltrs, draining out water, setting a side(or lowering if required) for repairs / cleaning etc., cleaning and removing accumulated sludge/ dirt scales from tank bottom, side and from mouths of circulating pipes of service tank of capacity not exceeding 500 litre, located on roof of building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enamel paint on black ground “Cleaned on (date)”, height of words 100 mm, and hoisting if required , re-fixing and reconnecting in position after cleaning , complete all as specified and directed .

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, from chowkhat , complete all as specifieand directed.

Taking down chowkhats or frames not exc 1.5 sqm each with shutters without taking off shutters from the frame and removing from site, including cutting holes for taking out hold fasts and making good disturbed portion in cement mortar 1:3 or PCC 1:2:4 type B1(after inserting new hold fast if required), complete all as specified and directed.Note:(Hold fast shall be measured and paid seperately).

Taking down chowkhats or frames exc 1.5 sqm but not exc 4.0 sqm each with shutters without taking off shutters from the frame and removing from site, including cutting holes for taking out hold fasts and making good disturbed protion in cement mortar 1:3 or PCC 1:2:4 type B1 (after inserting new hold fast if required), compete all as specified and as directed. Note:(Hold fast shall be measured and paid seperately).

Material and labour for 105 mm x 60 mm pressed steel frame made of MS sheet 1.25mm thick, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc., with and including back filling with PCC (1:3:6), type C-0(using 12.5mm graded stone aggregate) , complete all as specified and directed . Note: The sizes/dimensions and type (profile) of frames shall be as shown in IS

Material and labour for 125 mm x 60 mm pressed steel frame made of MS sheet 1.25mm thick , for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc., with and including back filling with PCC (1:3:6), type C-0(using 12.5mm graded stone aggregate), complete all as specified and directed . Note: The sizes/dimensions and type (profile) of frames shall be as shown in IS.

Material and labour for Factory made polyvinyl chloride door frame of size 50 mm x 47 mm with a wall thickness as 5 mm, made out of extruded 5mm PVC foam sheet, mitre cut at two corners and joined by inserting 2 Nos of 150mm long brackets of 15 mm x 15 mm MS square tube. The two vertical door profile are to be reinforced with 19 mm x 19 mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided throughout the frame. The door frame shall be fixed to wall using 65/100 mm long MS screws through the frame by using PVC fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete all as per shown on SSR 2010 Part-II and as directed by Engineer-in-Charge. Make: Rajshreer/ Sintex or equivalent.

Material and labour for Factory made moulded door shutter with particle board core, 28 to 30 mm thick (stiles), with 2 Nos raised panel design with 2 mm thick moulded prelam PVC sheet on the front face & 2 mm prelam PVC sheet on back face, complete all as per manufacturer instructions complete all as specified and directed by Engineer-in-Charge.

Material and labour for Factory Made 35mm thick IInd class hard wood(Hallock) plain, framed, panelled shutters ( two Nos of panels)with lock rail and panel of 9 mm thick BWP commercial ply medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

Material and labour for Factory Made 35 mm thick IInd class hardwood (Hollock) skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a), complete all as specified and directed .

Material and labour for factory made flush shutters 35 mm thick, ISI marked, solid core construction, with block board core and plywood face panels, commercial type on both faces , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing, in Repairs drapery rod of mild steel 25mm dia, ribbed/fancy type, PVC powder coated, any shade, including set of fixing brackets, for span not exceeding 2m, fixed to wall in repairs, with PVC finols/finnels, connected accessaries, rubber packing, required screws and PVC rawal plugs as required complete all as specified and directed by Engineer-in-Charge.

Supply and fixing, mild steel Chromium plated 20 mm dia curtain rod, bright finish, including set of fixing brackets, fixed to wall in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, 100 mm, ISI marked , complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section , complete all as specified and directed.

S&F 200 mm aluminium anodized, barrel tower bolts of extruded section , complete all as specified and directed..

Supply and fix 150mm size aluminum handle, 'D' type anodized , complete all as specified and directed.

Supply and fix, Aluminium alloy, anodised, sliding door bolts 250 mm long, ISI marked, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy 12mm dia,complete all as specified and directed by Engineer-in-Charge.

Material and labour for Welding in repairs not exceeding 2.5cm in length (thickness of metal to be welded not exceeding 6mm) including cleaning preparing the surface and holding the members in true position for maintenance of steel items such as gates, grills, doors, windows etc., complete all as specified and directed by Engineer-in-Charge.

Supply and fixing, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to steel frames with tinned tacks, or galvanized wire staples, or fixed to wooden frames with first class hard wood bead, complete all as specified and directed by Engineer-in-Charge.

Material and labour for 18 mm/ 19 mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination for wooden and fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Supply & fix, block board 18mm / 19mm thick, grade 2 quality, interior grade, commercial type fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around, fixed in repairs, complete all as specified and directed.

S & F in repairs plain fillets square, rectangular or triangular in section, 2nd class hardwood of sectional area exc 13 & n exc 25 sqcm, clean sawn, wrought finished secured with screws complete all as directed.

Supply & fix Continuous (piano) hinges, mild steel, bright finish or electro galvanised, 30 mm wide flap (when open), fixed in repairs, complete all as specified.

Supply & fix 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, fixed in repairs, complete all as specified.

Taking down wooden shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm from steel frame/wooden frame and refixing after easing and adjusting and refixing builders harware in the same opening complete all as directed by Engineer-in-Charge.

Dismantling of brickwork / brick masonry, built in cement or cement lime mortar , including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Material and labour for Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre mean radius in cement mortar (1:4), using old size bricks, complete all as specified.

All as per item No. 93 here in before but except bricks. Note:- Serviceable bricks retrieved from Serial item No 92 here-in-before shall be reused(rates include for cleaning and handling of bricks also)

Material and labour for Raking out joints of old brick tiles/ cement concrete tiles , laid on roof , average 10 mm deep and cleaning with wire brush and re-grouting and flush pointing the joints in cement mortar (1:3) mixed with 5% of crude oil by weight of cement to make it leak proof, complete all as specified including removing all grass, bushes, dirt and dust etc.

Material and labour for Uprooting completely tree/ plants (upto 30 cm girth) from wall or any part of building upto double story buildings, making good disturbed portion and filling holes in cement mortar (1:3) PCC (1:2:4) to match with the existing surfaces, complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 75 mm bore PVC (SWR) bends any radius complete all as specified.

Material and labour for Preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Material and labour for Preparation of new or previously untreated steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces and apply two coat of oil bound distmper over a coat of primer & chalk whitening & smoothening of surface, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Preparation of newly plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M &L for preparation of newly plastered surface of ceiling and applying three coats of white wash , complete all as specified

Note:- Amount of credit of Rs. 36210.00 for retrieved materials is mentioned in Schedule of Credit Page No 112 & 113 of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/S V K Construction Co

sscontractor engineers

Dhillon Construction Company

Baba Engineers and Contractors

MOHAMMAD RASHID