CA NO.CWE BLY/GE (W)/142 OF 2025- 2026SPECIAL REPAIRS TO BLDG NO P-08 SINGLE JCOS LIVING ACCN OF JRC BAREILLY UNDER GE WEST BAREILLY

M&L for non-skid ceremic plain coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match of tiles incl dismantling of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

All as per serial item No 2 as above but as in vertical surfaces of tiles and rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified and directed.

M&L for non- skid ceremic plain coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for Glazed plain coloured ceramic tiles wall 600x300x7mm thick on vertical faces of walls including 10mm thick rendeing in CM 1:4 set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm each and not exc. 4.00 Sqm including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

S&F Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. complete as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F 125x60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1, necessary fixing lugs, SS hinges, lock strike plate, 02 x MS bar/flat at bottom of the frame etc, complete including wooden texture finished paint on the frame surface complete all as specified and directed.

S&F 105x60mmx1.25mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1 necessary fixing lugs, SS hinges,lock strike plate, 02 x MS bar/flat at bottom of the frameetc, including wooden texture finished paint on the frame surface complete all as specified and directed.

S&F 30 mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side complete all as specified and directed.

M&L for 35mm thick plain framed glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, with sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass including campsule mesh tightly fixed with the glazed and skelton door shutter etc, of 2nd class hard wood, members of shutters as specified in SSR Part - I Section 8 clause 8.24 (a) fitted to chowkats all as specified and directed.

S&F in repair factory made PVC Cupboard frame of the size 75mm x 40mm with a wall thickness of 5mm, made out of extruded 5mm thick plain/prelam PVC sheet of density 600 kg/cbm, having bottom width of 50mm and thickness of 10mm. All four frame lengths reinforced with 15 mm x 15mm M. S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners adjointed with 2 nos. of 15mm long brackets 0f 10mm x10mm M S square tubes. The door frame shall be fixed to the wall using 8/100 long M S screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member and minimum of 2nos. of screws to be provided horizontal member etc. complete as per direction of Engr-in-Charge, manufacturer's specification and drawing.

S&F factory made PVC cupboard flush type shutter of 30mm thick consisting of frame made out M S tubes of 19 gauge thickness and size 19mm x 19mm for stiles and rails. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement/ cynoacrylate adhesive with 5mm thick plain/prelam PVC sheet, on both side of inside panel incliding necessary items to fix the shuter to frame such as 100mm stailess steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutter.All four edges of the panel to be sealed with lipping of 10mm thick and 20mm wide PVC sheet baton (made by sticking 2nos. PVC foam sheet of 5mm thickness using PVC solvent cement adhesive). complete as per direction of Engr-in-Charge.

S&F 100mm long stainless steel butt hinges complete all as specified and directed.

S&F 150mm long aluminum anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm long aluminum handles, cast type complete all as specified and directed.

S&F 150mm long Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed mild steel complete all as specified and directed.

S&F galvanised Stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanesed wire stapels complete all as specifed and directed.

M&L for preparation of old wooden surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for painting to wood and wood based surfaces of any description exc 10cm with or girth with two coats of synthetic enamel paint over a coat of pink primer including preparation of newly or previously untreated surface complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for painting to steel surface exc 10 cm width or girth with two coats of synethic enamel paint over a coat of red oxide primer including preparation of newly or previously untreated surface complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1(using 20 mm graded aggregate) as in bed blocks for hold fast/concrete filling in chowkhats and similar work etc complete all as specified and directed.

M&L for 15mm thick cement plaster on brick surfaces or concrete surfaces (on external surface) in cm (1:4) using WPC @ 200 ml per 50 kg of cement including taking down plaster finishing the surface even and smooth without using extra cement and necessary scaffolding complete all as specified and directed. Note :- WPC shall not be paid separately for this item.

M&L for 15mm thick cement plaster on brick surfaces or concrete surfaces (on external surface) in cm (1:4) using WPC @ 200 ml per 50 kg of cement newly surface even and smooth without using extra cement and necessary scaffolding complete all as specified and directed. Note :- WPC shall not be paid separately for this item.

M&L for 12mm thick cement plaster on brick surfaces or concrete surfaces (on internal surface) in cm (1:6) including taking down plaster finishing the surface even and smooth without using extra cement and necessary scaffolding complete all as specified and directed.

M&L for 12mm thick cement plaster on brick surfaces or concrete surfaces (on internal surface) in cm (1:6) newly surface even and smooth without using extra cement and necessary scaffolding complete all as specified and directed.

M&L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) finished including taking down plaster the surface even and smooth without using extra cement and necessary scaffolding complete all as specified and directed.

M&L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) newly surface even and smooth without using extra cement and necessary scaffolding complete all as specified and directed.

M&L for three coats white washing ceiling surfaces including preparation of newly plastered untreated surfaces and necessary scaffolding complete all as specified and directed.

M&L for preparation of old decorated surfaces and applying three coat of white wash on ceilings surfaces and rubbing down with sand paper to have even and smooth surfaces complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment and applying two coats of oil bound distemper using Airless spray technology operating single spray gun paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper using Airless spray technology of operating single spray gun and paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment and applying two coats of exterior weather proof paint using Airless spray technology operating single spray gun paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying weather prrof paint should be able to spray in hard to reach areas and penetration of paint on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of exterior weather proof paint using airless spray technology of operating single spray gun and paint usage over a coat of 1 mm thick layer of wall care putty and certified by paint manufacturer and as mentioned in PS and accessories for applying weather proof paint should be able to spray in hard to reach areas and penetration of paint on the surface to achieve excellent application using limited manpower complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, aches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L brick work with fly ash old size bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

M&L brick work with fly ash old size bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

M&L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IIIrd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and directed.

M&L for form work to edges of concrete rough finished surface flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and directed.

M&L for Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick complete all as specified and directed.

M&L for formwork to sides and soffits of lintels,lintel bend, beams etc finished rough surfaces of concrete complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20 mm graded aggregate as in slab, shelves and stair case etc. incl demolition of existing RCC slabs, shelves etc other than groung floors at any postion , any description with matching to adjoining disturbed surfaces complete all as specified and directed.

M&L for RCC type B 1, 1:2:4 (20mm graded agg) as in beams, cantilevers, lintels, over 1.5 m span incl demolition of exising RCC beams at any position, any description with matching to adjoining disturbed surfaces complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20 mm graded aggregate as in chajjas and like incl demolition of exising RCC chajjas and like at any position, any description with matching to adjoining disturbed surfaces complete all as specified and directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposing the reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical, apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx 50 mm (10 mm gauge welded mesh ) & tack , securing with clips / linding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @ 200 ml every 50 kg of cement and applying two coat of ezee at interval of 8 hours cure for the surfaces complete all as specified and directed.

Demolition of cement concrete(un-reinforced), in any position and paving n.exc. 15 cm thickness (below or above ground level) including tile/ terrazzo floor complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in Sub base, floors, sub floors, paving, plinth protection 75 mm thickfinished even and fair including forming 10 mm wide joints at not exceeding 3 m distance between adjoining slabs shall not exceed 10 mm in thickness and shall be filled with bitumen mastic i.e. bitumen and sand in proportion 1:2 complete all as specified and directed.

M&L for providing water proofing treatment to RCC sunken slab as specified and directed as under:- (a) Cleaning the existing RCC sunken slab and vertical wall/RCC beam and hacking the surface. (b) 15mm thick plastering over the floor & vertical surface in CM 1:4, mixed with liquid water proofing compound @ 200ml per 50 kg of cement trowelled to even and smooth finish without using extra cement .(Water proofing compound shall be measured and paid separately). (c ) filling the sunken portion with water for 72 hrs and carring out the ponding test.(Any leakage /seapage noticed shall be repaired). (d) Applying two coats of elastomaric acrylic water proof coating in each coat with roller application.(Note: Each coat of elastomaric acrylic compound requires 6-8hrs to dry up itself second coat shall be applied on getting the first coat completely dried up.)

Supply only liquid waterproofing compound complete all as specified and directed.

M&L for cement concrete type E2 1:5:10 (40 mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate as in levelling course, haunching, coping and similar works of over RCC roof surface including rounded or chamferred on edges etc all as specified and directed.

M&L for 15 mm thick rendering on fair faces of concrete surfaces in CM 1:4 with water proofing compound concrete surface complete all as specified and directed.(NOTE:- WPC shall be measured and paid separatly)

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified and directed.

M&L 25mm thick cement concrete type B1 1:2:4 using 20mm graded stone aggregate in floor finishes even and fair to receive floor tiles.

Supply and providing water proofing treatment with polyster based water waterproofing membrane standard water proofing membrane 3 mm thick, wt not less than 3.5 kg/ sqm having 10 years guarantee for water tightness all as specified and directed and described as under : (a) Prepartion of RCC roof surface and applying one coat of polymer modified bitumen 85/25 @ 1.2 Kg/Sqm over a coat of polymer primer @ 0.30 Kg/Sqm including cleaning surface, all as per manufacture's specification complete complete all as specified and directed. (b) Supply & Providing APP based polyster based water waterproofing membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced/ torch application of membrane with 10 cm overlaps as required thereof, complete all as specified or as directed.

M&L for applying one coats of Bitumen based UV reflective and water proofing paint with aluminium finish over APP membrane and maximum coverage 8.00 Sqm per litre per coat on non assessible roof over APP membrance complete all as specified and directed.

M&L for 18-20 mm thick green marble (of any type) work (table rubbed and polished) in riser & steps, cills and like jointed in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed and making V-groove 5mm wide and 5mm deep in 3 nos on the tread in length wise 25mm centre to centre complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps , cooking platform, and other similar situations complete all as specified and directed

S&F in repairs Vitreous china wash down water closet pedestal pattern, duroplast slim seat cover, slow falling seat cover size 69x37x77CM / 66x35x71 complete, including connection to drain pipe etc complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed.

S&F in repair fancy type chromium plated Stop valve (angle stop valve) type suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair 15 mm dia bib tap fancy type chromium plated with flange quarter turn incl all necessary fittings complete all as specified and directed.

S&F in repairs 450mm long PVC connection 15mm bore with PTMT nuts complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Refixing 15mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Refixing 20mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

S&F 15mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

S&F in repairs 100mmx100mm stainless steel grating fixed complete all as specified and directed.

S&F in repair fancy type 20 mm dia stainless steel towel rack size 600mm long including a pair of brass bracket complete all as specified and directed.

S&F in repairs vitreous chinaware coloured wash hand basin with padestal of size 55X40X82cm complete including CP Waste coupling ,waste pipe ,complete fixing arrangement and cutting for and pinning in walls & making good complete all as specifed and directed.

S&F in repair fancy type 150mm size square brass CP shower rose with or without swivel joints complete all as specified and directed.

S&F in repairs Brass chromium plated wall mixer 2 in 1, 15mm for mixing hot & cold water incl provision of over head shower, screwed down three joints to steel pipes or unions and plugging and screwed to walls incl necessary fitting complete all as specified and directed.

S&F in repairs health faucet 1.25 mtr long flexacle tube with 15 mm dia SS Braided connection tube with wall hook complete for ETWC incl necessary fitting complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed.

S&F in repair fancy type 15 mm bore brass chromium plated WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB complete all as specified and directed.

S&F low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls complete all as specified and directed.

S&F in repairs mild steel chromium plated Curtain Rod 25 mm dia of approved quality with two number decorative design as approved brackets fixed in brick/concrete wall and same finished knobs on each end of curtain rod complete all as specified and directed.

S&F 500 ltrs capacity rotational moulded polythylene triple layered water storage tanks white in colour (cylindrical vertical with closed top) hoisted and fixed in position incl demolition of Old RCC ranks and removing debries / demolished material from the premises complete all as specified in SSR Part I complete all as specified and directed.

S&F 15mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified and directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down AC/PVC rain water pipe, soil/ waste/ vent pipe of any size with fittings etc. complete all as specified and directed.

S&F PVC (SWR) 110 mm dia soil waste or rainwater drainage pipes single socketed in any length with rubber ring joint laid in floor or fixed on wall complete all as specified and directed.

S&F PVC (SWR) 110 mm bore bends complete all as specified and directed.

S&F in repair PVC (SWR) floor trap/multi floor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain including jointing to waste pipe fixed in cement concrete (1:2:4), type B-1 complete all as specified and directed.

S&F PVC (SWR) 75 mm bore soil, waste or rainwater pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed.

S&F in repairs PVC 100mm bore Y-Junction piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and directed.

S&F PVC 100mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and directed.

S&F PVC 75 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or shocket type) or with parallel branches with oval access door complete all as specified and directed.

S&F 100mm bore PVC bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and directed.

S&F 75mm bore PVC bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and directed.

S&F in repairs 80 mm bore PVC cowl complete all as specified and directed.

S&F powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality) for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and including 5.50 mm thick figured glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clipsa, frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for three tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed in aluminium window or along with F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such as aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. Note : Rate for glass and wire shall not be paid separately.

S&F stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed.

S&F mild steel window grills box type framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding, FE-290 grade E-165 complete all as specfied and directed.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 75mm dia pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 100mm dia pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Taking down carefully aluminium point wiring any type including battens if any except for ceiling or where not feasible for light/ fan//bell/socket or power and including unscrewing from board, fitting and fixture such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down carefully unserviceable main switch DBs of any description of an size in any position complete all as specified and directed.

Taking down submain wiring including all accessories complete all as specified and directed.

M&L for point wiring with single core FRLS 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with all conduit accessories, screws (concealed conduit wiring in walls and casing capping on ceiling or roof) including metal box suitable for modular fittings and covered with modular plate and cover of suitable size with new brass screws for mounting switch sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for:- (a) One light / fan/ exhaust fan point controlled by one switch.

(b) One 5 pin 5 Amp switch socket out let point on an independent board.

(c) One 5 pin 5 Amp socket out let point controlled by one switch on same board.

(d) One buzzer/ bell point controlled by one push button on the same board with other switches or independent

All as per item 110 here in before but for one 15 Amp 6 Pin switch socket out let independent with 2.5 Sqmm FRLS (Nominal Area) PVC unsheathed copper conductor single core multistranded incl 2.5 sq mm FRLS PVC copper conductor single core used as earth continuity conduct complete all as specified and directed.

S&F Modular switch one way 6 A, 1 Module complete all as specified and directed.

S&F Modular switch one way 16 A, 1 Module complete all as specified and directed.

S&F Modular bell push 6 Amp, 1 Module complete all as specified and directed.

S&F Modular Socket 6 Amp, 2/3 Pin combined 2 Module complete all as specified and directed.

S&F Modular Socket 6/16 Amp, 2/3 Pin combined 2 Module complete all as specified and directed.

S&F Modular fan regulator Step up type, 120 Watt, 2 Module complete all as specified and directed.

S&F ceiling rose PVC / Poly carbonate, Isolated body, three terminal AC 230 volts complete all as specified and directed.

S&F replacement of lamp holder, PVC / Poly carbonate, insulated body modular type with back plate batten/angle type for batten fittings complete all as specified and directed.

S&F in replacement LED mirror light fitting of 1 x 10 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection complete all as specified and directed.

S&F in replacement LED mirror light fitting of 1 x 20 watt LED batten with aluminium housing with all accessories prewired suitable for wall /surface mounting complete with connection all as specified and directed.

S&F indoor decorative LED City-3 light fitting suitable for & including single 12 Watt LED lamp with polycarbonate body with upper globe complete all as specified and directed.

S&F LED lamp 12 Watt, 230 V , AC integrated circuit complete all as specified and directed.

S&F Buzzer, Ding Dong AC. 230 volts,single pole complete all as specified and directed.

S&F security light fitting, LED type, 25 Watt, 6000 K, pressure die cast housing with prismatic polycarbonate diffuser & indvl LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 1.20 m long fixed to wall with and including nut, bolts and GI clamps of size 50 x 6 mm as required including two coats of synthetic enameled paint over a coat of primer and making connection with three core 23/.0076 rubber insulated copper cable from ceiling rose to connector of street light complete all as specified and directed.

M&L for sub main wiring with two single core 6.0 Sqmm (FRLS) copper conductor PVC unsheathed cable medium grade including PVC conduit (appropriate size) concealed in wall for sub main connection including 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. (Note :- Two runs of 6.0 sqmm (FRLS) and one run of 6.0 sqmm (FRLS) copper conductor shall be measured as one unit length.)

Taking down carefully ceiling fan from existing site and doposited in MES yard for BER in coming BOO complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed.

S&F MCB SPN 40 Amp 240 volt complete all as specified and directed.

S&F MCB single pole 6 to 32 Amp 240 Volt 'B' curve 10 KA complete all as specified and directed.

S&F flush sheet metal enclosure SPN DB 6 way with double door IP-42 protection detachable gland plates, flush mounting for MCB fitted with bus bar , earth bar and neutral links complete including taking down old complete all as specified and directed.

S&F TPN DB -TPN DB 4 way with provn and including of MCCB 63 Amps , 415 Volt, 3 Phase, 4 wire AC 50 Hz having aluminium Bas Bar phase and the neutral insulated with PVC sleeves, connected with appropriate size copper thimbles complete all as specified and directed.

S&F 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN/FP 40 to 100 AMP current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed.

M&L for in replacement earthing complete with galvanised steel earth plate 600x600x 6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate using 4 mm dia GI wire as earth wire electrode moulded and rivetted to earth plate at one end and connected to main switch/ control switches of buildings at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto main switch board of building including 20 dia bore GI pipe 'light grade' as water pipe from earth chamber and including excavation and earth work, PCC 1:3:6 type C1 chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced complete all as specified and directed.

Please Enable Macros to View BoQ information