SPECIAL REPAIR TO SINGLE JCOs LIVING ACCN EST SECTION (JCOs/OR) AT IMA DEHRADUN

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each including cutting holes for taking out of holdfast & making good in CM (1:4) after fixing new chowkats/ frames complete all as specified.

All as per item No 1 above but not exc 1.5 Sqm each

S & F factory made coloured WPC door frame 100% Solid, size 125mm x 65 mm double rebated ,made from wpc material comprising of virgin PVC polymer of K value 58-60, calcium carbonate and natural fibres minimum compressive strength of 58 N/mm2, and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in position with SS dash fasteners of required dia and length, colour of door frame to match that of shutter all as per specifications drawings complete all as specified and directed. (colour to be approved by Engineer-in charge )

All as per item No 3 above but of size 100 mm x 50 mm, single rebated.

All as per item No 3 above but of size 70 mm x 45 mm, single rebated for cupboards.

S & F factory made 35mm thick 100% Solid WPC solid decorative type flush Door Shutter of required size comprising of virgin PVC resin of K Value 58-60, Calcium Carbonate and natural Fibers and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cum having good screw holding capacity, Minimum Compressive Strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. Material test certificate and authentication should be compulsory and shall be provided by the manufacturing company complete all as directed and specified.

All as per item No 6 above but 20 mm thick WPC shutter for cupboards complete all as specified and directed.

M&L for 30 mm thick factory made solid WPC gauged door shutter with wire mesh in three number of division with brown wood grain texture, including SS wire mesh fixed with (15 x 15 ) mm square tubes in side rails with screwing 8x28 heat metal zinc coated screws that can be removed or fixed again after changing of wire mesh when needed covered with moulded beading complete all as specified and directed. Note:- Gauged door shutter shall be fabricated from single piece of WPC board.

S&F stainless steel butt hinges of size 100 mm Class 'B' fixed full body threaded star headed counter ss sunk screws.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised with of flap (when open) 30 mm etc complete all as directed and specified.

S&F 150 mm long stainless steel handles, cast type complete all as specified

S&F stainless steel tower bolt 200 mm long complete all as specified and directed.

S&F stainless steel sliding door bolt 250 mm long with hasp, staple (bolt type) and fixing clips of sheet, and fixing bolts and sliding bolts of SS complete all as directed and specified.

S&F 150 mm size hasp and staple, safety type, stainless steel with mild steel hinge pin including bolt to hinge plate and fixed with screws

S&F double legged floor door stopper 150 mm long of Stainless Steel with rubber etc complete all as specified and as directed

S&F ball catches with 8 mm dia steel ball magnet catches for cupboard shutter including striking plate as approved etc complete all as directed and specified.

Supply and fixing mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate ISI marked complete all as specified.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples.

S & F in repairs 25 mm dia Stainless Steel 1 mm thick curtain rod including fancy type brackets, and decorative end caps etc. fixed to wall complete all as specified.

M&L for preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing of old steel or iron surfaces over 10 cm width or girth and applying one coat of Synthetic enamel paint.

M&L for aluminum alloy powder coated standard hollow section as mentioned below window frame (Bombay sliding) with two glazed shutter and one number wire gauged shutter sliding type, with aluminum sections as per Series-B (18mm) 3 track of Jindal section for sliding windows, with and including glass to shutters tinted/ coloured glass 5mm thick, fixed with glazing clips, rubber beading / gasket anodised beading, screw and lock type 2 Nos aluminium handle of size 75mm and locking system including aluminium grill of 5 mm thick, average width of aperture 50mm including S&F stainless steel wire cloth to shutter with 0.36 mm dia of wire and 1.40 aperture complete all as specified and directed.

M & L 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) including necessary form work as in sub base for flooring etc., complete all as specified.

M & L for 25 mm thick PCC 1:2:4 type B-0, (using 12.5 mm graded crushed stone aggregate) as in floors, to receive surface of tile including demolition of old PCC/ flooring complete all as specified and directed.

M & L for 8-10 mm thick vitrified tiles of light shade of size 600 x 600 mm Group B i (a) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed.

All as per item No 25 above but on vertical surfaces as in skirting, dados over and including 10 mm thick rendering in CM 1:4 including dismantling of old skirting complete.

M&L for Non skid vitrified (heavy duty) ceramic coloured tiles 8 to 9mm thick (Square or rectangular) Group B i (a) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in epoxy coating grout to match the shade of tiles with and including laying of 15 mm thick screed bed or bedding layer in CM 1:6 complete including dismantling of existing floor tiling including cement mortar bedding and removing rubbish off the premises complete all as directed.

All as per item No 27 above but on vertical surfaces as in skirting, dados over and including 10 mm thick rendering in CM 1:4 including dismantling of old skirting complete.

M & L 16 mm thick granite (colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 15 mm thick cement screed bed 1:6 CM as in door & window cill and small pieces for soap dish etc including cutting,chases and inserting in wall in horizontal or vertical surfaces including grinding the edges half round where required) and polishing complete all as specified and directed.

M&L for Cutting holes superfacial area exc 150 but n exc 400 Sqcm into or through brick walls built in cement mortar and making good in CM 1:3 or cement concrete 1:2:4 type B-l as required

S&F in repairs, 75 mm bore outlet cast iron floor trap incl cockroach trap with gratings including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete all as specified.

S&F in repairs, 50 mm bore Cast iron (vertically cast spun pipe) soil, waste and vent pipes, in any length without ears, laid in trenches or in floors or fixed to wall complete all as specified and as directed

S&F in repairs, for 75 mm bore Cast iron (vertically cast spun pipe) soil, waste and vent pipes, in any length with, laid in trenches or in floors or fixed to wall complete all as specified.

S&F in repairs, 100 mm bore Cast iron (vertically cast spun pipe) soil, waste and vent pipes, in any length without ears, laid in trenches or in floors or fixed to wall, complete all as specified.

S&F in repairs, 75mm bore cast iron Tee of (any radius) equal or unequal, spun pipe diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified.

S&F in repairs, 100 mm bore cast iron Tee of (any radius) equal or unequal, spun pipe diminishing pieces or tapers with oval access door complete all as specified.

S&F in repairs, 50 mm bore cast iron cowls complete all as specified and as directed

M & L Bands, straps, including bolts, if required, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde-E-165.

M&L for 15mm thick (Average thickness) rendering on fair faces of concrete in sunken portion in CM 1:3, mixed with water proofing compound on vertical and horizontal surfaces and providing slope towards outer wall and finished even and smooth without using extra cement.

M&L for 15mm thick rendering in CM 1:3 on damaged portion of concrete in small patches (in repairs) to facia/ ceiling of roof projection in double storied building including removing loose material on vertical and horizontal surfaces finished even and smooth without using extra cement.

M&L for water proofing treatment to sunken roof slab with APP based modified polymeric membrane as per manufaturer's instructions with following course of description (a) Applying a priming coat of bituminous primer @ 0.30 kg/sqm, till the surface is properly impregnated. (b) Apply a coat of bitumen 85/25 grade @1.20 kg/sqm over primer. (c) Over the coat of bitumen as above APP modified polymeric membrane (weight not less than 3.5 Kg/Sqm with over lap of 100mm). The overlaps are then sealed/fused by flame or bitumen Note: Rate of this item inclusive ponding test demolition and removal of old sunken WPT. The ponding test (for 48 hours) shall be crried out by the contractor, if any defect noticed the same portion shall be rectified by redoing by contractor without any extra cost to Govt.

M&L Cement concrete1:7:12 in sunken portion filling and mass concrete as directed.

M&L for Non skid glazed ceramic coloured tiles 7 to 8mm thick Group B i (a) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including of 15 mm thick screed bed in CM 1:6 complete.

M&L Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick Group B i (a) on vertical surface of wall such as skirting/ dados, set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10 mm thick rendering in CM 1:4, including dismantling existing wall tiles/ dados, complete all as specified and as directed.

M&L PCC/ RCC 1:2:4 type B-1 using 20 mm graded stone aggregate in benching and copings and small counters etc incl demolition of existing concrete as directed.

M&L for brick work with sub class 'B' bricks, in half brick thick wall built in CM 1:4 straight or curved on plan to any radius with old size bricks incl demolition of old brick work complete all as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (20 mm graded stone aggregate) as in surface channels and drains. (Saucer Drain)including demolition of old PCC complete all as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/ stopped ends etc. complete.

M&L for 15mm thick rendering on other than fair faces of brick/ concrete surfaces in CM 1:6 finished even and fair including taking down old cement plaster raking out joints hacking for keys, scrubbing down with waters etc, complete.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair including taking down old cement plaster raking out joints hacking for keys, scrubbing down with waters etc, complete all as specified and directed.

M&L for Complete removal of existing treatment from walls.

M & L for preparation of new or old wall surface and applying 0.75 to 1 mm thick Birla white/ JK wall care putty over internal and external plaster to make the surface smooth as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted, over one coat of alkali resistant primer complete all as specified & directed.

M&L for preparation of old decorated plastered surfaces of ceiling and applying one coat of whitewash complete all as specified & directed.

M & L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

S&F in repairs, medium grade galvanized steel tubing with all fittings &fixed complete to walls & ceiling or laid in floors 15 mm dia bore pipe (including in short length) complete all as specified and as directed

S&F in repairs, tubes medium grade galvanized with all fittings and laid in trenches, 20 mm bore dia pipe (including in short length) complete all as specified and as directed

S&F in repairs 500 litre rotational moulded triple layer polyethylene water storage tanks ISI marked of approved make white colour (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part-I, including one no PTMT ball valve high pressure and two nos of 20 mm dia gun metal gate valve to each tank, complete all as specified and directed.

M & L for cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed.

Supplying and laying in repairs, of 16 mm outer dia CPVC pipes pressure rating 6kg/cm2 SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laid in floors complete all as specified.

Supply only Male Brass Threaded Adaptor (MBTA) 16 mm outer dia for CPVC pipes ISI marked.

Supply only Brass elbow 16 mm outer dia for CPVC pipes ISI marked

S&F Vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests including replacement of 'P' or 'S' CI, concrete bedding and making good existing floor fixed in repair complete all as specified and directed.

S&F Vitreous china wash down water closet pan (pedestal pattern) white including seat cover with necessary PVC pipe fittings fixed in repair complete all as specified and directed.

S&F PVC low level flushing cistern 10 Ltr capacity conforming to relevant IS or ISI marked of approved make syphonic action type white including ball valve, float valve and handle including bracket and PVC flush pipe fixed in repair complete all as specified and directed.

S&F in repairs, vitreous china counter top wash hand basin white of size approx 450x300mm, fixed over RCC counter, CP waste coupling & waste pipe complete all as specified and directed

S&F in repairs cast copper alloy stop valves/ angle valve 15mm bore fancy type chromium plated, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher

S&F in repairs, 15 mm bore chromium plated, fancy type. long body bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher

S&F 15mm size PVC connection with PTMT nuts length 450mm long ISI marked of approved make.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long of approved make.

S&F in repair Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed

S&F CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher

S&F CP brass hot & cold 15mm dia wall mixture for mixing hot & cold water with shower (3 way)provn with connecting legs & flanges in complete all as specified. Make : Jaquar Opal Prime Series/ Cera Ruby series/ Kolher

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repair CP brass chromium plated shower rose 125mm size with extension CP Arm pipes of approved make

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges of approved make

S & F for stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed.

S&F fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with fancy type screws complete all as specified and directed. Model: ACN - 1173 of Jaquar , Parryware Model No T6010A1, Cera Model No F505101

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc.

Taking down old U/S main switches, Sheatmetal enclosures DB including MCCBs, MCBs etc including making good to the disturbed surface of wall all as directed.

Taking down old unsv T/L, Lamp,Security light of any size and capacity all as directed.

Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed.

Taking down existing ceiling fan of any capacity and make serviceable by replacing unsv parts and preparation of old painted surface body and blades of ceiling fan of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody and refixing at site after compltion of bldg work.

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

All as per item No 86 above but with stranded copper conductor 4 Sq mm (nominal area), two single core, PVC insulated cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated stranded copper conductor 4 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

Supply and fix modular switch 1 way 10A, 1 Module

Supply and fix modular switch 1 way 20A, 1 Module with indicator lamp

Supply and fix modular socket 10A, 2/3 pin combined 2 Module

Supply and fix modular socket 10A/20A, 2/3 pin combined 2 Module

Supply and fix modular fan regulators step type 2 module 120W .

Material and labour for ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as directed.

S&F LED tubelight batten fitting 20/22 Watt made of aluminium housing suitable for fixing on walls/ceiling, warm/natural/cool white as per requirement at site complete all as specified and directed by Engr-In-Charge. Make: BRIGHT LINEA of Crompton/LUMILINE PLUS NEO of Havells/ Essential SmartBright Batten of Philips

S&F LED tubelight batten fitting 10/12 Watt made of aluminium housing suitable for fixing on walls/ceoling including connections, warm/ natural/ cool white as per requirement at site complete all as specified and directed by Engr-In-Charge. Make:Trim Linea Neu of Crompton/ SmartBright of Philips/ ENDURA LINEAR NEO of Havells.

Supply and fitting LED street light fitting 35 Watt 230 V AC outdor type with high presure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with iinpact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Supply and fix exhaust Fan ,made of sturdy Engineering plastic complete with louvers shutter of approved make voltage 230volts ,50HZ,RPM 1200,copper winding of sweep 250mm including cutting holes on wall and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface.

Supply and fix in repir Sheet metal enclosure for DB`s SPN, with 200amps rated bus br, 8 way, 240 volts double door Make Standard/HPL/Legrand, complete all as specified & as directed by Engineer- in -Charge.

Supply and fix in repair MCB SP 6 to 32 Amps 240 volts 10 KA 'C' series Make : Complete all as specified & as directed by Enginer -in - Charge.

Supply and fix n repair MCB SPN 40 to 63 Amps 240 volts 10 KA C series Make : Complete all as specified & as directed by Enginer -in - Charge.

S & F in repair Distribution boards epoxy powder coated TP & N (VTPN MCCB DB) fabricated from minimum 1.6 mm thick CRCA sheet and fixed/ flush to wall and suitable for universal mounting with 250 Amps fully insulated copper Bus Bar for each phase and 02 neutral shrouded bar ,2 earth bar and cable tie for cable management with reversible door for IP-43 DB,S protection,415 volt ,suitable for fixing FP MCCB 100/125 Amps as incomer and 24 SP MCBs or 4/8/ 12 TP MCBs (or any combination of SP/TP MCBs) outgoings of following capacity and making good the distrubed surface complete all as directed. Note: Suitable MCCB and outgoing MCBs will be measured separately under relavant items of this schedule)

4 Way VTPN DB (FP MCCB +12 MCB,C). Make :legrand / L&T/ ABB, Schneider

S & F MCCB ,4 pole ICS=100% ICU at 415 volts with rupturing capacity 16 KA with thermal-magnetic release and adjustable overload setting . The MCCB shall have a Mechanical life = 40000 operations & Electrical life = 8000 operations of following capacity complete all as directed. Make: Legrand, L&T, ABB, Schneider

S & F sub main wiring with 2 run PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes complete all as specified and directed. Make of Conduit : Polycab/ Finolex/ Plaza Note:Two run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit.

2 x 6 Sqmm + 1 x 6 sqmm

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm thick GI wire by means of nuts,bolts,check nuts & washers of galvanized iron or steel,protected by 15mm bore light grade galvanised iron pipe and connected to main switch board,including all necessary excavation & earth work in hard dense soil including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle and necessary testing complete all as shown in electrical plate No 3 of SSR part-I all as specified and directed.(one earthing for each main Panel )

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. Marking MES No. with paint and kept in safe custody at site after compltion of bldg work.

Please Enable Macros to View BoQ information