ADDN/ALTN TO CERTAIN BLDG AT BAKNAUR UNDER GE (AF) AMBALA

M&L for Mild steel plates/sheet, Fe-290 (Gde E165) plain or chequered, 5mm thick or over in thickness cut to size, fixed to open floor duct complete all as specified and directed.

S&L PVC flame retardant flooring exceeding 4mm not exceeding 6mm thick complete all as specified and as directed.

Excavation in post holes (or similar holes) each not exceeding 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and mixed with earth around, inlayers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface in soft/loose soil complete all as specified and as directed.

M&L for PCC type D-2 (1:4:8), using 40 mm graded mechanically crushed stone aggregates as in filling & mass concrete, complete all as specified and directed by Engr in Charge.

M&L for PCC type B1 (1:2:4), using 20 mm graded mechanically crushed stone aggregates as in filling fdn/footings & mass concrete, complete all as specified and directed by Engr in Charge.

M&L for form work to sides of concrete foundation, footing , plinth beams, and similar works, for rough finished surfaces complete all as specified and directed

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not ness than 0.9mm dia or securing with clips all as directed by Engineer-in-charge

All as per BOQ srl item No 7.00 here-in-before but 6mm to 8mm dia, complete all as specified and directed.

S&F steel work in tubular truss including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979 of grade St-240 complete all as specified and as directed.

M&L for mild steel joist, channel, angle, tee section fixed independently with out connecting plate etc. (cut to ordinary lengths) conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S&F prepainted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws / L type or J type hook complete all as specified and directed.

S&F mild steel flat iron for wind tie etc including necessary drilling holes and fixing with necessary self drilling and self tapping screws/bolts and nuts, neoprene and limpet washers with 150mm end laps wherever required complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar all as directed by Engr-In-Charge.

S&F mild steel framed work as in door of angle or other sections with gusset plates, rails, braces etc, using ornamental design as approved complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and purpose made hinges or steel hanging door fittings including running rails and guides and hanging, fastening, fixing and Cutting holes in brick/Stone/RCC walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete conforming to Fe 410E, Gde E-250 including taking down and making good finish complete all as specified and as directed.

M&L for Mild steel plain, black 1.25mm thick sheet in steel gates and similar work , cut to size, fixed to steel framing gates with plain 40mm lap joint with welded or riveted complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed.

S&F GI metal powder coated suspended ceiling of approved materials of size 595x595mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120grams/Sqm, both side inclusive) consisting of main "T" runner with suitably spaced joinets to get required length and of size 24x38 mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm centre to centre and cross 'T' of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main 'T' at 600mm center to centre from a grid of 1200x600mm and secondary cross 'T' of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to forms grids of 600x600mm and wall angle of size 24x24x0.3mm and laying false ceiling tiles of approved texture in the grid including , required cutting/making, opening for services like diffusers, grills light fittings fixtures smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvansied butterfly level clips of size, 85x30x0.8mm spaced at 1200 center to center along Main 'T' , bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications including fully perforated 12mm thick micro tegular edge or 10mm thick square edged GRG false ceiling tiles decorateive finish fixed to frame work with hold down clips in false ceiling including taking down complete all as specified and as directed. Note: Unit rate quoted against this item shall also includes taking down and refixing the same of any electrical board, switch, sockets, light and fittings, fance etc carrying out necessary relevant work and making good to match witch existing surfaces effected for this area etc.

Dismantling brick tiles or terracing tiles single layer on roof, cleaning and stacking the serviceable tiles for reuse, offering credit for unserviceable tiles and removing rubbish to a distance not exceeding 250 Mtr complete all as specified and directed..

Demolition of mud in roof any thickness including plastering and leeping (Whether full thickness removed or only part thereof) complete all as specified and directed.

M&L for roughening surfaces of roof after removal of mud phuska completely and applying cement slurry with 3.00 Kg /Sqm complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5mm mechanically crushed stone graded aggregate laid over roof slab as in padding to make good the depressions all as specified & directed by Engineer-in-Charge.

Material and labour for 15mm thick plastering in cement mortar 1:4 on Concrete/RCC roof slab surfaces, (using water proofing compound by 3% weight of cement) finished even and fair without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured & paid separately

Supply only integral water proofing compound and mixed with cm as per manufacturer instructions, complete all as specified and directed.

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm & adjoining vertical surfaces including applying bituminous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces complete all as specified and directed.

M&L for 40mm thick brick tiles laid and bedded in cement mortar 1:6, 15mm thick and joints grouted flush in cement mortar 1:3 mixed with 5% or crude oil by weight of cement complete all as specified and as directed.

All as per BOQ srl item No.27.00 above but except tiles, complete all as specified and directed.

Taking down cement plaster of any description on brick walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 15mm thick on fair face of brick walls or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair face of brick walls or concrete surfaces in CM 1:4 mixed with WPC @ of 2% by wt of cement finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick cement plaster in CM 1:3 in the ceiling/ soffits of slabs/chajjas/sunshade etc and finishing the surface even and smooth without using extra cement complete all as specified and directed.

Supply only Dr fixit integral WPC /liquid complete all as specified and directed.

M&L for preparing newly plastered surface of wall and applying two coats of Oil bound distemper over a coat of wall care putty complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on walls as backing etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M & L for screed bed or bedding layer of mortar 15mm thick for laying floor finished in CM 1: 6 complete all as specified and directed.

M&L for rendering 10mm thick on fair face of brick walls or concrete surfaces in CM 1:4 as backing complete all as specified and directed.

M&L for vitrified ceramic tiles dark shade/double chagred 10mm thick (Square) polished area of each tiles not exceeding 0.36Sqm(600x600), in floors etc set and jointed in neat cement slurry and pointed in white or coloured complete all as specified and directed.

M&L for joint free, non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm in floors, etc set and jointed in neat cement slurry and pointed in white/coloured cement to match, complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surfaces size 600x300x7mm/450x300x7mm thick set and jointed in cement neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M& L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed

M & L for 25 mm thick sand cushioning to receive interlocking tiles in flooring complete all as specified and directed.

M & L for providing cement concrete type B1 , 1:2:4 (20mm graded mechanically crushed stone aggregate) , mud storps, rounded or chamfered on edges of chequred tiles complete all as specified and directed.

M&L for brick work with subclass 'B" bricks, straight or curved on plan exceeding 6m mean radius built in CM 1:4 all as specified and directed.

M&L for machine cut kota stone slab as in flooring of size 580 x 580 mm each & 18-20 mm thick, set and jointed in cement slurry including border of 100mm wide baroda green mable as per pattern approved over & including screed of 20-22 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing, in floors/steps etc, complete all as specified. Note : 1. All the edges of slabs shall be grinded/cutted at the right angle before laying, so that paper thin, smooth jointing to be obtained. 2. The colour of the slabs shall be uniform.

M&L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as directed by engr-in-charge.

Taking down Chowkats With shutters(without taking of shutters from the frames) or frames complete all as specified and directed.

S&F powder coated aluminium frames for doors, windows, ventilators with one or more rebates including joining joining cleats for fixing etc complete all as specified and as directed.

S&F anodised aluminium door shutter, aluminium section weighing 0.55 kg/m including necessary joining cleat, glazing clips, rubber neoprene packing, handle 2 Nos in doors, hinges, anodised aluminium snap beading etc complete all as specified and as directed.

S&F anodised aluminium window and ventilator shutter, side hung type type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleat, glazing clips, rubber neoprene packing, anodised aluminium snap beading, scews anodised aluminium fittings such as peg stay 150mm long (01 No), hinges type B-21 100mm long (02 No) suitable handle (01 No) complete all as specified and as directed.

S&F aluminium anodised "Deco" grill, DG 102, 100 x 10 mm x 7 mm thick, approved design for windows/ventilators with F/U channel complete all as specified and directed Note :- F/U channel will be measured and paid seperately

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of operature 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

S&F sheet glass 5.50mm thick ordinary quality and glazing with oil and putty in square exceeding 0.5 sqm in each pane complete all as specified and as directed.

S&F solar control flim 50 micron reflective type sticked to glass panes as per instructions of manufacturer's complete all as specified and as directed

M&L for prelaminated particle board 12mm thick interior grade, prlaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws in aluminium works complete all as specified and as directed

S&F MS Mortice lock 4 levers vertical type size 100mm fixed in floor complete all as specified and as directed.

S&F for Mild steel work in window guard bars, plain, let in and fixed/welded independently in wooden/steel frames and similar work confirming to Fe 410 - O or Fe 310 - O, complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed in repair with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F Butt hinges 100 mm size, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 300mm long, Aluminium alloy, anodised sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150 mm size complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M&L for Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, ISI marked overall length of cover plate 140 mm fixed in floor with standard aluminium screws complete all as specified and directed.

S&F steel ventilators with top hung shutters including hinges, steel peg stay, complete with glazing bars etc complete all as specified and directed.

M&L for preparing surfaces of new or previously untreated surfaces of steel or metal works and applying two coats of synthetic enamel paint over one coat of red oxide over 10cm in width or girth complete as specified.

S&F in repair Door closer aluminium (dia cast) body hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

M&L for preparing of old/New steel / metal surfaces of any description viz. fencing, angle iron posts on security walls, roof trusses, purlins, rafters, etc. over 10cm in width or girth and applying one coat of synthetic enamel paint including all necessary staging, scaffolding, safety precautions, etc. as required to work at heights, etc. complete all as specified and directed by Engr-in-Charge

M&L for preparation of old or New surfaces of RCC / Stone / Concrete / brick walls/ Asbestos Cement Sheet or plastered surfaces and applying two coat of exterior acrylic emulsion paint in camouflaging pattern by auto roller of any shape and any size complete all as specified and directed by Engineer-in-charge, Note: (i) Sample of camouflaging pattern to be approved by GE/user as per user requirement. Pattern to be followed, will be given by the user.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed

M&L for point wiring complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC conduit ISI marked with accessories concealed in wall/ceiling/truss including cutting chases, pinning in etc with PVC non metallic ISI marked terminal boxes/ modular boxes concealed wall including one FRLS PVC insulated & sheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for :-

One light point controlled by one switch SP one way

One ceiling fan point controlled with one 5A switch

One 3 pin socket outlet 5 Amps on independent board

One 3 pin socket outlet 5 Amps on same board with other switches

M&L for point wiring for AC/ Geyser and one 3 pin socket outler 15 Amps independent with cable 4 sqmm single core multistranded FRLS PVC insulated unsheathed copper conduclors 1100 volts grade drawn through & including PVC conduit including PVC bend, tee joints etc as per site requirernent. ISI marked with accessories concealed in wall/ceiling/russ etc with PVC non metallic ISI marked terminal boxes concealed in wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 4 sqmm as earth continuity conductor connected to common earth as earth dolly complete all as specified and directed.

M&L for point wiring for 15 Amps socket complete with 2.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and incuding PVC coduit including PVC bend, tee joints etc as per site requirement, ISI marked with accessories concealed fixed in wall/celing/truss etc with PVC non metallic ISl marked terminal boxes / modular boxes sufacing on wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 2.5 sqmm as earth continuity conductor connected to common earth as earth dolly.

S&F in replacement Modular Switch, 6Amp, One way, 1 module, ISI marked complete all as specified and directed.

S&F in replacement Modular Switch, 16Amp, One way, 1 module, ISI marked complete all as specified and directed.

S&F in replacement Modular Socket, 6 Anps, 2/3 pin combined 2 module, ISI marked complete all as specified and directed.

S&F in replacement Modular Socket, 16Amps, 6 pin combined 2 module, ISI marked complete all as specified and directed.

S&F in replacement Modular type, electronic fan regulator ( 5 step ), 120 Watts, 230 volts, 2 Each module, ISl marked complete all as specified and directed.

S&F in replacement ceiling rose surface bakelite with ISI mark, complete all as specified and directed.

S&F Modular white cover plate with Frame 3 Module, ISI marked complete all as specified and directed.

S&F Modular white cover plate with Frame 4 Module, ISI marked complete all as specified and directed.

S&F Modular white cover piate with Frame 6 Module, ISI marked complete all as specified and directed.

S&F Modular white cover plate with Frame 8 Module, ISI marked complete all as specified and directed.

S&F Modular metal flush box 3 module, ISI marked and including cutting hole in wall/ceiling/pillar etc and making good surface, complete all as specified and directed

S&F Modular metal flush box 4 module,ISI marked and incluing cutting hole in wall /ceiling/piller etc and making good surface. cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed

S&F Modular metal flush box 6 module,ISI marked and incluing cutting hole in wall /ceiling/piller etc and making good surface. cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed

S&F Modular metal flush box 8 module,ISI marked and incluing cutting hole in wall /ceiling/piller etc and making good surface. cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed.

S&F in replacement LED tube lights fitting 1x 18W, 220V,AC decorative batten type with driver, holder including LED tube light connection up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

S&F in replacement LED tube light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F in replacement Ceiling light 36 WATT 2 ft X 2 ft Recess mounting led ultra slimceiling light with extruded aluminium housing and milky diffuser.LED ultra slim panel: complete all as specified and directed

S&F in replacement double door VTPN 4 way and incliding 4 pole MCCB 100 Amps as incoming, 200 Amps rated busbar, IP 54 inter connection link. cable ties, eath bar etc complete all as specified and directed.

S&F in replacement 08 way Double door SPN type having protection lP 54, with 200 Amps rated bus bar connecting with existing wiring circuits by providing copper pin terminals of suitable size complete all as specified and directed

S&F in replacement MCB SPN 63 Amps, 10 KA rating complete all as specified and directed.

S&F in replacement MCB SP 6-32 Amps, 10 KA rating complete all as specified and directed.

S&F in replacement submain wiring with proper colour coding. 4 single core FRLS 1100 volts grade cable with stranded copper conductor of size 4 Sqmm in and including PVC conduit of suitable size not less than 25 mm, ISl marked including 1 single core cable with stranded copper conductor of size 4 Sqmm (green colour) for earthing complete all as specified and directed Note: 5 runs of 4sqmm cable alongwith 01 run of PVC conduit of appropriate size will be measured as one length.

S&F in replacement Plug and Socket enciosure, in sheet metal enclosure with MCB, SP 20 Amps 240 Volts complete with metal clad socket for window type air conditioners complete all as specified and directed

Supply, installation, testing & commissioning of split AC inverter type units indoor/outdoor complete with cordless remote control unit and with inbuilt air ioniser & plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacityy 2TR, indoor fixed on hi wall and outdoor unit on wall mounted bracket, connecting of refrigerant and insulating copper tubing, detection of leakage, connection with copper cable 3 core of suitable size for indoor unit to outdoor unit complete all as specified & directed.

Supply & laying PVC pipe 20 mm dia heavy duty for drain out condensing water of split AC including cuttng outdoor opening of hole in wall and making good after laying of pipe etc match the existing surface complete all as specified and directed

S&F in replacement HDPE pressure rating 6kg/cm sq pipe of 63 mm dia including necessary bends, elbows, Tees etc on cable protection complete al as specified and directed by Engineer-in -charge. Make: Rex/ Suprime IPrince or equivalent approved by GE

Supply & laying in replacement cable XLPE insulated screened PyC bedded, galvanzeo steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor o size 50 sq mm 3.5 core. laid in duct I along polelwal tc including making connection complete all as specified and directed by Engineer-in-Charge.

S&F in replacement off load change over switch 415 V, 4 pole, 250 A as per existing make and model suitable equivalent make as per list of make at PS complete all as specified and directed.

Please Enable Macros to View BoQ information