Provn of 01x Kitchen for offr mess 15 ft x 12 ft room with shelves water supply fitment exhaust fan and complete wiring for 204 SATA Bty at Nimu Under AGE(I) Nimu

Amount

Excavation in trenches not exceeding 1.5m wide and n exc 1.5m in depth for foundations, laying of pipes etc and not exceeding 10 Sqm on plan for manhole etc and not exceeding 1.5 meter in depth and getting out in hard/dense soil, complete.

M&L Cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete.

M&L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate) block masonry with solid block exc 10cm in width and set as in wall etc in CM 1:6.

M & L 75mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded aggregate) as in sub base.

Cement Concrete, 1:2:4, type B1 using 20mm graded agg as in lintel upto 1.50 m span, cills, steps, seismic and other silmilar bands, plinth courses, sring courses,lacing courses, parapets and railings upt 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troghs and the like including weathering, slightly rounded or camphered angles and throating, as directed.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips.

All as per item No 06 here-in-before but of 6 and incl 10mm dia in stirrups, spacers and binders.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

Formwork to sides and soffits of girders, bressummers, lintels, cantilevers, shelves including supports, flat rough finished surface of concrete.

Formwork to sides of column, posts for Square and rectangular rough finished surface.

M & L RCC Nominal Mix Type B-I 1:2:4 (20mm graded crushed stone agg) as in foundations, indl rafts, footing foundation beams, plinth beams bases for columns, etc: basement slabs, under reamed piles and mass concrete.

M & L RCC Nominal Mix Type B-I 1:2:4 (20mm graded crushed stone agg) as in Beams, cantilevers, bressummers, lintels over 1.5m span.

M & L RCC Nominal Mix Type B-I 1:2:4 (20mm graded crushed stone agg) as in columns, pillars, posts.

S&F Roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beams, tee, angle, channel or flat sections) including distance piece, cleats etc. conforming to Fe 410 W (Gde- E- 250) quality A.

M&L applying two coats of synthetic enamel painting to new surfaces steel based over a coat of red oxide primer exc. 10 cm width/girth including preparation of surfaces including filling with filler where reqd all as specified and directed.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

All as per item No 16 here-in-before but plain steel sheet.

M&L for Vitrified ceramic (Light Shade) tiles 10mm thick (square/rectangular) polished, area of each tiles n.exc 0.36 Sqm in floors etc over and incl 25 mm pcc B-0. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed with CM(1:4).

M&L for Rendering 10mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:6) and finished even and smooth without using extra cement.

M & L preparation of new plastered surfaces and applying three coats of white wash on walls.

M&L for Rendering 12mm thick on fair faces of brickwork or concrete surfaces in cement mortar (1:4) with WPC and finished even and smooth without using extra cement (Note : WPC will be measured and paid separately).

M&L preparing new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer all as specified.

M&L for anodised aluminium frame (Powder coating minimum thinckness 50 microns) for door, window, ventilators with one or more rebates incl joining cleats for fixing etc.

S & F Anodised aluminium door shutter including powder coating of any colour (Thickness of powder coating not less than 50 micron), aluminium section weighing 0.55 Kg/M including necessary opening cleats, galzing clips, rubber neoprene packing, handles 2 Nos in each doors, hinges, anodised aluminium snap beading screws etc. complete all as specified.

S&F Anodised aluminium window and ventilator shutters including powder coating of any colour (Thickness or powder coating not less than 50 micron),side hung type without sash bars aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No) hinges ltype B-21 100 mm long (2 no) suitable handle (1 no) complete all as specified.

S & F 5.5 mm thk sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane.

M & L 2nd cl soft wood Plain fillets.sec area exc. 13 & n.exc 25 Sq cm as in square, rectangular or triangular in section, clean sawn, secured with nails or brads.

All as per item No. 27 above but sec area n.exc 3 sq cm bullnosed, splayed, chamfered or rounded on one edge or face.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in Ceilling.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in walls.

M & L hard core of broken stone and boulders gauge n exc 60mm deposited spread and level in layers n exc 15cm thick watered and rammed to a true surface.

M&L for PCC type C-2 (1:3:6) (40mm graded stone agg) 75mm thick as in plinth protection.

S&F 25mm dia MS drapery rod, teak wook finish, good quality including wooden finish PVC brackets for holding of curtain rod and end knobs of mathing colour complete all as specified and directed by Engineer-in-Charge. Note: A set of 2 Nos knob shall be provided at every 1.5 to 2m length (an average basis) of drapery rod as directed by Engineer-in-Charge.

Returning, filling in excavated soil including spreading, leveling watering and well ramming in layers not exceeding 25cm thick complete.

Removing excavated material (soils) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete.

M&L for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed for One light point controlled by one switch.

One 3 pin 5 amps socket outlet independent with cables 1.5 sqmm size

One 3 pin 5 Amp socket outlet on same board.

All same as per item No 36 above but with conductor of size 2.5 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 2.5 sqmm PVC insulated stranded copper conductor Cable.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified and directed.

S&F socket 2 in 1, 5 pin 5 Amp flush type complete all as specified.

S&F switch piano flush type 5 Amp, single pole, one way complete all as specified and directed.

S & F Switch piano, flush type single pole, one way 15 Amp

M&L for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engr-in-Charge.

S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge.

S&F Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling of capacity 34 watt & size 2'x2' complete with driver and all as specified & directed by Engr-in-Charge. Note: The rate quoted include the cost of any frame reqd for LED light fitting in ceiling recess.

S&F LED bulkhead fittings designed for modern homes available with premium quality diffuser for glarefree light and easy to install snapfit installer of capacity 6.5 watt complete all as specified and directed as Engr-in-Charge.

S&F exhaust fan 300 mm sweep durable plastic body complete with lovour all as specified and directed.

S&F sheet metal powder coated versatile double door SPN distribution board, 12 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link, earth bar and din rail suitable for use on 240 Volt, 50Hz .

M&L for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminimum conductor of size 16 Sq mm twin core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, flat or circular all as specified and directed.

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earth lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified.

M&L for laying tubes medium grade galvanised with all fittings laid in trenches of size 20 mm bore.

Supply and fixing gun metal gate valve ISI marked cast copper alloy screwed down high pressure with clutch or butterfly handle screwed both ends for iron pipe or for union and fixed complete all as specified for the size 20 mm dia bore. Make : Kirloskar/Sant

Cutting of existing GI water main pipe line upto 25mm bore in position for making branch connection (insertion of GI Tee) including excavation and earth work complete all as directed. Note : GI fittings such as tee, elbows, collar, reducer etc joint and jointing material for fixing of cast iron fittings shall be measured and paid separately.

osho traders

SASPOL LARJAY CONSTRUCTION

M/S LIBE & CO

MS INFRATECH

M/S MA CONSTRUCTION Co

M/S STANZIN NOBROO

M/S ABDUL SAMAD MIR