PROVN OF OTM ACCN FOR 36 X OFFRS INCL STUDENT

Amount

Note: (i) Please refer Schedule 'A' Notes given on serial page No. 23 to 27 of tender documents. (ii) Unless otherwise specified, earth work and excavation shall be measured and paid separately.

DISMANTLING AND DEMOLITION WORKS

Taking down chowkat or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc 4 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified.

Taking down shutter of any description exc 1.00 sqm and n exc 2.00 sqm each and removal from site complete all as specified and directed.

Refixing of shutters of any description in same openig n.exc 1 sqm each complete all as specified and directed.

Refixing of shutters of any description in same openig exc 1 sqm but n.exc 2 Sqm each complete all as specified and directed.

Hacking out old broken glass from wooden/metal frame of any thickness incl punching or drilling out old glazing pins/springs clips and providing and fixing new ones complete all as spcified.

Dismantling of timber scantiling 40 sq cm and over in section in any position as in unframed work complete all as specified.

Dismantling of plain or corrugated steel sheeting , any gauge and thickness in roof covering including Nainital or similar pattern roof covering complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) and boarding any thickness, including cover fillets complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

Demolition of brick/stone work built in cement mortar complete all as specified and directed.

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed.

Taking down or up 15mm bore GI tubing including cleaning for refixing or removal to store etc complete all as specified and directed.

Taking down or up 20mm bore GI tubing including cleaning for refixing or removal to store etc complete all as specified and directed.

Refixing old 15mm bore GI tubing and connections in new or old position (wall, ceiling, floor etc) complete all as specified and directed.

Refixing old 20mm bore GI tubing and connections in new or old position (wall, ceiling, floor etc) complete all as specified and directed.

Dismantling steel poles/struts, any size and removing the base concrete from pole, shifting,depositng the pole to MES store yard complete all as specified by Engr in charge

Dismantling of ACSR or AAC conductors, coiling it properly and shifting, depositing it to MES Storeyard complete all as specified and directed by Engr incharge.

Dismantling cross-arms of M.S. channel or angle sections etc. complete and shifting, depositng it to MES storeyard.

Dismantling insulators any type, any size and depositing it to MES store yard complete all as specified and directed by Engr incharge

BUILDING AND INTERNAL SERVICES WORKS

S&F Pressed steel frames for doors (size of frame 105 x 60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

Providing, cement concrete type C1 1:3:6 ( 20 mm garded agrregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

S&F 2nd Class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and as directed

S&F 2nd class hard wood 40 mm thick plain, framed, panelled shutters (any number) with panels of timber flat on both side (feather edge) or of veneered particle board medium density, wood particle board with commercial face veeners and fixed to chowkats complete all as specified.

S&F 2nd class hard wood 35 mm thick glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats complete all as specified and directed.

S&F 300 mm size mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 100 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed type B-11 complete all as specified.

S&F 300 mm long brass sliding bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified.

S&F 200 mm long extruded brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F 150mm long extruded brass handles fabricated type polished complete all specified and as directed.

S&F 2nd class 30 mm thick hardwood (Kail) glazed skeleton shutters open rebated and prepared to receive guage etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc and fitted to chowkats size of members of shutters as specified in SSR Part - I section 8 Clause 8.23 (b) for windows, ventilators etc are provided with stiles and rails, complete all as specified.

S&F 75 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed type B-12 complete all as specified.

S&F 125 mm long extruded brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F 125mm long extruded brass handles fabricated type polished complete all specified and as directed.

S & F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares exceeding not 0.5 Sq. M in each pane complete all as specified and directed.

M & L sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames complete all as specified and directed.

M & L pin head type figured glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and avarage width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple complete all as specified and directed.

75 mm Hasp and staple, safety type, aluminium anodized hinge pin inluding bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge.

S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings and as directed by Engineer-inCharge.

S&F Aluminium anodised 100 mm long Butt hinges with galvanised mild steel screws complete.

S&F Aliminium anodised barrel tower bolts, 150 mm long complete.

S&F Aluminium anodised handles, cast type anodised 125 mm long complete.

S&F of aluminium anodised frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified including powder coating (minimum thickness of powder coating 50 micron).

S&F Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joint cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium sanp beading screws etc, complete all as specified, including powder coating (minimum thickness of powder coating 50 micron).

S&F Anodised aluminium window and ventilator shutters, aluminium section weighing 0.55kg/m including necessary joint cleats, glazing clips, ruber neoprene packing, , hinges, anodised aluminium sanp beading screws etc, complete all as specified, including powder coating (minimum thickness of powder coating 50 micron).

4.80mm thick sheet glass, ordinary quality and fixed with rubber beading exc 0.5 Sqm in each pane

19mm thick prelaminated particle boards, solid core with decorative face veneers on both faces fixed with screws to timber frame work complete all as specified and directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanished, width of flaps (when open) 30mm.

S&F 2nd class hard wood planed one side with butt joints as facia boarding of 20nmm thick complete all as specified and directed.

S&F of Mild Steel Hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc complete all as specified and directed.

S&F of 1st class hard wood of 75 x 50mm wooden hand rails rounded or shaped with splayed faces in straight and fixed complete all as specified and directed.

S&F of 40mm dia brass conduit pipe fixed with brass bracket complete all as specified and directed.

S&F of standard brackets made to shape and welded to MS Plate, complete all as specified.

S&F of wooden konb fixed on cup board shutter of wooden complete all as specified and directed.

M & L 2nd Class soft wood (Kail) as in scantling, clean swan timber framed and fixed, complete all as specified.

2nd Class soft wood (Kail) as in scantling to be reused as obtained from dismantling, clean swan timber framed and fixed, complete all as specified and directed.

0.63 mm thick, galvanized, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs,walls etc with grade of zinc coating 275 grams per square metre complete all as specified and directed.

Except sheeting (obtained from dismantling) galvanized, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs,walls etc complete all as specified.

0.80 mm thick plain , galvanised , mild steel sheeting , in ridges, hips, valley gutters, drip and straight flashing ( length and girth as fixed ) with grade of zinc coating 275 grams per square metre complete all as specified.

S & F Mild steel work in framed work such as grills, gratings,framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 410 - O or Fe 310 - O complete all as specified and directed.

S & F Rolled Mild Steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy backet framing confirming to Fe 410 W (Gde E-250) quality B including distance pieces, cleats, etc., complete all as specified and directed.

S & F Mild steel work in framed brackets of angles or tees with web and flanges cut to shape, drilled and counter sunk for screw, including bending and welding angles as necessary and similar work including bending and welding angles as necessary confirming to Fe 290 Gde E-165 complete all as specified and directed.

S & F mild steel screw bolts (Machine made) with hexaagonal or square heads at one end and screwed the other, or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut n exc 5 cm long complete all as specified and directed.

S&F for 12 mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice laminated & other side balancing white lamination, fixed with screws to timber frame work complete as in ceiling flat or sloped complete all as specified and approved by EIC.

S&F GI frame work for seamless ceiling of size of grid 605 x 605 mm with comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate chanel 0.9 mm thick having two equal flanges of 15 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasters with and including ceiling section (not exc 1.2m length) of 0.55 mm thick having kurled web of 50 mm and flange of 26 mm each with lips of 109.5 mm fixed to intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and fixed as specified and directed.

S&F for 6 mm thick 5 Ply wood, grade BWR type BB fixed with nails to timber frame work on wall etc complete all as specified and directed.

M&L providing and fixing Gypsum board 12mm thick in ceiling fixed with screws as per manufacture's instructions complete all as specified and directed.

S & F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 and not exceeding 13 Sq. cm complete all as specified and directed.

S & F second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with nails, cross sectional area not exceeding 3 Sq. cm complete all as specified and directed.

M&L for 50 mm thick PCC 1:2:4 type B-0 (using 12.5 graded aggregate) as in floors finished even and fair complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 graded aggregate) as in floors finished even and fair complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm in floors etc over 15mm cement screed in cm 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

S&F non skid ceramic coloured tiles of 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm in floors, over and including 15 mm thick screed in CM (1:4) set and jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M&L machine cut kota stone slab flooring 20 - 25mm thick over 15mm cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to the match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L 18 to 20 mm thick green marble any shade tiles 30cm x 20cm x 20mm thick machine cut, bedded jointed and pointed with grey cement slurry incl cutting and polishing typesmm thick laid over 20mm thick screed bed in CM 1:4 as steps, jambs, window cill, cooking platform and like incl pointing in white cement 1:2 using marble dust admisture of pigment to match with marble shade complete all as specified and directed.

M&L 20mm thick granite stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing complete laid top and sides of cooking plat form over 15mm thick sceed bed in CM 1:4, complete all as specified and directed.

S&F glazed ceramic coloured tiles 7mm thick 450 x 300mm size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 15mm thick cement plaster (1:4) complete all as specified and directed.

M & L machine cut kota stone slab flooring 20 - 25mm thick over 15mm cement screed base in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to the match the shade of the slab including rubbing and polishing on vertical surfaces such as skirtings, riser of steps, dado, and pillars etc complete all as specified and directed.

80mm thick machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006 M-40 grade pointed with grey cement and pigment over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for sand filling under interlocking tiles 50mm thick including watering and consolidating complete all as specified and directed.

M&L Cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling, sub base and mass concrete complete all as specified and directed.

Plain cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) as in benching, bed plates, coping and the like including necessary formwork and finishing all exposed surface of concrete as per clause 4.11.16.2(a) & (d) of SSR Part-I complete all as specified and directed.

75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified and directed.

Mild steel TMT 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality complete all as specified and directed.

RCC 1:2:4 type B-1, 20mm graded aggregate in slabs etc, complete all as specified, rough finished surfaces complete all as specified and directed.

Form work to soffits of slab such as roof beam,lintles cantilever ,landing and similar work complete all as specified and directed.

M&L for brick work built in cement and sand mortar 1:4with sub class 'B' old size bricks straight or curved on plan exceeding 6m means radius but except bricks only complete all as specified and directed.

M&L for Brick masonary using Sub Class 'B' bricks, straight or curved on plan built in cement mortar 1:6 complete all as specified and directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Rendering 15mm thick in patches in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick in patches in cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smoothe without using extra cement & with using integral water proofing compound complete all as specified and directed.

Rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in celing complete all as specified and directed.

S & F in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440 X 260 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor complete all as specified and directed.

S&F in repairs vitreous china wash down closet pan (Pedestal pattern) including seat cover and fixing to trap including connection to drain (or out going pipe), flusing pipe, anti syphonage pipe fixxing bolts but excluding flushing cistern complete all as specified and directed.

S & F in repair PVC low level cistern of 10 lit capacity inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make complete all as specified and directed.

S&F in repair wash hand basin (pedestal type) of size 550 x 400 mm vitrous China white flat back including brackets, waste coupling , UPVC low density polyethyne (LDPE) pipe of pressure rating 6 kgf/Sqcm & PVC waste pipe of 32 mm dia etc. complete all as specified and directed.

S&F Vitreous china urinals, flat back large type, of size 59 cms x 37.50 cms x 39 cms coloured,incl 05 ltrs capacity of automatic flushing cistern, 20mm bore medium grade galvanised iron flush pipe, 32mm bore of medium grade GI Waste pipe up to outlet drain, 15mm polythene over flow pipe to flushing cistern complete all as specified and directed.

S & F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality complete all as specified and directed.

S & F in repair 15 mm bore CP Angular stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F urinal spreader of PTMT any colour for fixing with 15mm dia pipe (minimum weight 60 gms) complete all as specified and directed.

S&F in repair 15 mm dia bore Chromium plated fancy type Pillar tap screwed down high pressure with or without lettred Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm dia bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed ccomplete all as specified and directed.

S&F in repair brass chromium plated shower rose 125 mm of size with arme and with or without swivel joints to steel pipe or union complete all as specified and directed.

S & F in repairs 15 mm dia bore concealed stop valves cast copper alloy chromium plated fancy type with long shank & cup (concealed type) complete all as specified and directed.

S&F in repair 15 mm dia bore bib taps cast copper alloy with crutch and butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and directed.

S&F 125mm dia grating doom with/without waste hole of PTMT (Minimum weight 40 gms) complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repair CP soap tray fixed to walls with rubber plugs complete all as specified and directed.

S&F of toilet paper holder 150mm x 150mm recessed roll type complete all as specified and directed.

S&F 2000mm x 600mm mirrors of 5.50mm thick of size including AC Boards & PVC frame complete all as specified and directed.

S&F 20mm Harrison rail anodised aluminium alloy with fixing brackets,stops ,roller etc.complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding of cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M&L Salt glazed stoneware gully traps, square or round mounted, type 'P' of size 125 x 100mm complete all as specified and directed.

Cement concrete 1:4:8 type D2 as in foundation of gulley trap complete all as specified and directed.

S&F C.I Perforated gratings 150mm x 150mm for gulley traps complete all as specified and directed.

M&L PCC 1:2:4 type B1 as in kerb of gully trap complete all as specified and directed.

M&L Cement concrete type C 2 1:3:6 (40mm graded aggregate) in foundation complete all as specified and directed.

M&L Expanded metal, for reinforecement of cover slabs weighing 4kgs/sqm for gully trap cover complete all as specified and directed.

M&L Cast iron floor trap with grating including jointing to waste pipe in run lead, 75mm complete all as specified and directed.

M&L Cast iron Nahani trap with grating including jointing to waste pipe in run lead, 75mm complete all as specified and directed.

S&F branch pieces single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100 mm bore of pipe with over excess door.

S&F branch pieces double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100 mm bore of pipe with over excess door.

S&F Bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F Bends (any radius) diminishing pieces or tapers with oval excess door, 100mm bore of pipe complete all as specified and directed.

S&F Bends (any radius) with duck's foot or heel rest 100mm bore of pipe complete all as specified and directed.

S&F Cast iron 'P' or 'S' trap 100mm bore of pipe complete all as specified and directed.

S&F branch pieces single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 75 mm bore of pipe with oval excess door complete all as specified and directed.

S&F Bends (any radius) with duck's foot or heel rest 75 mm bore of pipe complete all as specified and directed.

S&F Bends (any radius) with oval excess door, 75mm bore of pipe complete all as specified and directed.

S&F Cast iron cowl, 75mm bore of pipes complete all as specified and directed.

S&F Cast iron soil waste and vent pipes in any length, 100mm bore of pipe, fixed to walls complete all as specified and directed.

S&F Cast iron soil waste and vent pipes in any length, 100mm bore of pipe, Laid in trenches complete all as specified and directed.

S&F Cast iron soil waste and vent pipes in any length, 75 mm bore of pipe, fixed to walls complete all as specified and directed.

M&L Run lead joints for 100mm bore of pipe complete all as specified and directed.

S&F in repairs 250 ltrs capacity Rotational moulded polyethylene in white oloured three layered ISI Marked water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F in repairs 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & hihdesity plastec ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms) etc complete all as specified and directed.

S&F in replacement of 15mm bore gun metal gate valves, with iron wheel head, screwed both ends suitable for iron pipe complete all as specified and directed.

S&F in replacement of 20mm bore gun metal gate valves, with iron wheel head, screwed both ends suitable for iron pipe complete all as specified and directed.

M&L for lagging on 15 mm internal dia pipe all round with 50 mm thick bonded mineral wool pre-formed 'SNAP ON' pipe section of density of 144 Kg/Sqcm confirm to IS 9842 including providing with chicken mesh wire netting 25 gauge 20 mm mesh and 0.01 mm aluminium foil etc complete all as specified and directed.

M&L for lagging on 20mm internal dia pipe all round with 50 mm thick bonded mineral wool pre-formed 'SNAP ON' pipe section of density of 144 Kg/Sqcm confirm to IS 9842 including providing with chicken mesh wire netting 25 gauge 20 mm mesh and 0.01 mm aluminium foil etc complete all as specified and directed.

S&F 20mm outer dia of 3- layer PPR Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) unstalised and antimicrobial fusion welded having thermal stability for hot or cold water supply including all PPR pain & brass threaded polypropylene random fittings fixed complete to wall, celings or in floors complete all as specified and directed.

S&F 25mm outer dia of 3- layer PPR Polypropylene random copolymer concealed pipes SDR 7.4 (PN-16) unstalised and antimicrobial fusion welded having thermal stability for hot or cold water supply including all PPR pain & brass threaded polypropylene random fittings fixed complete to wall, celings or in floors complete all as specified and directed.

M&L 20mm dia of deformed bars as in rungs, cut to length, bent to shape required including cranking, bending spirally for hooping for coloumns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for preparation of old plastered surfaces of ceiling and applying two coats of Oil bound distemper over a coat of chalk whitening on ceiling etc complete all as specified and directed.

M & L for preparation new plastered or unplasterded surfaces of walls and applying two coats of Oil bound distemper over a coat of chalk whitening on wall etc complete all as specified.

M & L for preparation of old undecorated surfaces of walls and applying two coats of Oil bound distemper over a coat of chalk whitening on wall etc complete all as specified and directed.

M&L for applying of 3mm thick wall care putty on ceiling surfaces etc complete all as specified.

M&L for applying of 3mm thick wall care putty on wall surfaces etc complete all as specified and directed.

M&L for 3 coats of white washing on ceiling incl preparation of new surfaces complete all as specified and directed.

M&L for 3 coats of white washing on walls incl preparation of new surfaces complete all as specified and directed.

M & L for preparation old undecorated surfaces of walls and applying two coats of Cement Base Paint of approved tint, complete all as specified and directed.

M&L prepariation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of coat of red oxide complete all as specified and directed.

M&L prepariation of new wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparing new zinc (or galvanized) surfaces to receive painting by coating with mordant solution including washing and cleaning etc. of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F 75mm Hasp and & staple, safety type, aluminium anodised hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S &F Terrazo tiles 20 cm x 20 cm x20 mm thick with grey cement and pigment with size of chipss upto 6 mm, set jointed and pointed in neat slurry in floor over 20mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L 75mm thick 1:4:8 type D2 (40mm graded stone aggregate) complete all as specified and directed.

S&F Steel rolling shutters, without ball bearing, 1.25 mm thick laths, including top cover, anchoring rod, hasp and staple, erected in position as indicated, gear operated type with bevel gear box and crank handle, complete all as specified and directed by the Engineer-in-Charge.

M&L 2nd class hard wood Plain fillets. Square, rectangular or triangular in section, clean sawn, of sectional area Exc 13 & not exc 25sqcm and secured with screws, complete all as specified and directed.

M&L Plugging to brick walls complete, for wood fillets, grounds, moulding, boarding, etc., at distances not exc 1mtr complete all as specified and directed.

S&F 2nd class soft wood of 15mm thick boarding,planed one side with butt joints and fixed with nails in any situation, complete all as specified and directed.

Preparation of new or previously un treated wooden surfaces of any description, over 10cm in width or girth and applying fillar coat with thin varnish or lacquer or shellac varnish, staining and two coats of varnishing paint complete all as specified and directed.

SEWAGE DISPOSAL WORKS

Septic tank exc inordinary soil foundation in PCC brick work in CM 1:4 RCC slab covers including RCC precast manhole cover (MD) having 6 mm plate embeded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chamber, etc complete for 10 users, all as per shown on drawing No CESZ/TD-1079/2011 sheet 1/1 complete all as specified and directed.

- Ditto - all as per above item no. 4.01but 25 users, all as per shown on drawing No CESZ/TD-1080/2011 sheet 1/2

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 3.6m dia and 3m depth. all as per shown on drawing No CESZ/TD-1078/2011 sheet 1/1 complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8m dia and 3m depth,all as per shown on drawing No CESZ/TD-1078/2011 sheet 1/1 complete all as specified and directed.

Cutting into existing manholes for connecting new drains pipe making good to pipes rendering cutting out existing benching for & forming branch channel (1/2 round of ¾ section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required internal dia of pipe 150 mm dia complete all as specified and directed.

M&L PCC 1:3:6 type C-2 using 40mm graded stone agg in foundation and mass concrete complete all as specified and directed.

M & L Brick work with sub class 'B' burnt bricks (old size bricks) straight on curved on plan exc 6 M mean radius built in CM 1:4 complete all as specified and directed.

M & L 1:2:4 types B-1 (using 20 mm graded stone agg as in coping etc complete all as specified and directed.

M&L for 100 mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed.

M&L for 150 mm dia Reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed.

M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate including packing under haunching against the sides of pipe after they are laid and tested for 150mm dia complete all as specified and directed.

M&L for concrete bed to drain pipes in PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate including packing under haunching against the sides of pipe after they are laid and tested for 150mm dia complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces with WPC, finished even and smooth complete. (WPC shall be measured and paid separately) complete all as specified and directed.

M&L for for rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels, drains etc complete all as specified and directed.

Extra for forming fair faces (finished) drain of channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitered stopped end etc complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia and over, cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Mild steel TMT bars 10 mm dia over, cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L precast RCC man holes cover in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate set in cement mortar 1:4 complete all as specified and directed.

S&F Rolled mild steel in joist channel, angle(size 50x50 x 6 mm th), or tee sections fixed independly, without connecting plates, etc (cut to ordinary length) of Fe 410w (Gde E250) gde A supplied and fixed complete all as specified and directed.

EXTERNAL ELECTRIC SUPPLY WORKS

Supplying, laying, jointing and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 11000 volts, grade cross sectional area 95 sqmm 3 core with earthed system confirming to IS: 7098-1985 laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and directed.

Supplying, laying, jointing and testing XLPE insulated,armoured under ground heavy duty electric cable with stranded aluminium conductor, 1100 volts, grade nominal cross sectional area 25 sqmm 4 core laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and directed.

Supply, laying, testing and commissioning of XLPE insulated, PVC sheathed, multistranded aluminium conductor armoured cable of 1100 volts size 120 Sqmm 3.5 core grade in trench/ surface of wall/ in GI pipe including fixing hardware, clamps, making good the damaged surfaces etc, complete all as specified and directed

Supplying, laying, jointing and testing of PVC insulated, aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed, 1100 Volts grade heavy duty cable, 2 core, 6 Sqmm (nominal cross section), stranded conductor, in service connections laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and directed.

Supplying, laying, jointing and testing of XLPE insulated, aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed, 1100 Volts grade heavy duty cable, 4 core, 10 Sqmm (nominal cross section), stranded conductor, in service connections laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and directed.

Supplying, laying, jointing and testing of XLPE insulated, aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed, 1100 Volts grade heavy duty cable, 4 core, 16 Sqmm (nominal cross section), stranded conductor, in service connections laid in trenches, in floor, in duct, through pipes or along the pole complete all as specified and directed.

Supply, laying, testing and commissioning of XLPE insulated, PVC sheathed, multistranded aluminium conductor armoured cable of 1100 volts size 95 Sqmm 3.5 core grade in trench/ surface of wall/ in GI pipe including fixing hardware, clamps, making good the damaged surfaces etc, complete all as specified and directed

Supply, laying, testing and commissioning of XLPE insulated, PVC sheathed, multistranded aluminium conductor armoured cable of 1100 volts size 70 Sqmm 3.5 core grade in trench/ surface of wall/ in GI pipe including fixing hardware, clamps, making good the damaged surfaces etc, complete all as specified and directed

'Supply, laying MS tubes, light grade, galvanised, 50mm bore, laid in trenches or under floor or road or fixed with pole for protection of electric cable.

'Supply, laying MS tubes, light grade, galvanised, 80mm bore, laid in trenches or under floor or road or fixed with pole for protection of electric cable.

'Supply, laying MS tubes, light grade, galvanised, 150mm bore, laid in trenches or under floor or road or fixed with pole for protection of electric cable.

Sand cushioning to underground electric cable all as per clause 19.75 of SSR Part-I

Sub class 'B' common kiln burnt clay building bricks, old size 230mmx115mmx75mm, laid at right angle along the cable over sand cushioning, as cable protection, complete, all as specified.

S&F LED street light fitting suitable for pole dia 54mm(max) for 90 watt LED with ported driver 10KV surg protection as per IS 15885 Part-II (lamp type 5700K) lumen out put should be (9560 lux) energy saving & environmental friendly verstile pressure die-cast aluminium housing IP66 protection road way ,optics Asymetric, with high power COB LEDs icl all accessories cat part No ENDURACITYLINERNEOSL90WLED757SASYBOTG of havells or its equivalents complete all as specified and directed by engineer -in-charge. Note : The contractor shall be produced the two yrs warranty card during supply.

S&F medium Grade GI tubing of dia 50mm as in bracket for fixing of street light fitting complete all as specified and directed by Engr-in-charge.

Supply, jointing and testing cable end terminal joints, outdoor type (Cold shrinkable) complete suitable for aluminium conductor cable 3 core,6.6//11KV UG XLPE/pilca cable of size 50 to 95 Sqmm.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x6 mm thick burried directly in gound (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 32x6mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (Weight not less than 4kg/Sqm) and frame of angle iron 25x 25x3mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of Bronze/Gun metal with fixing arrangement, funnel, wire mesh and excavation/earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 metre, complete all as specified and directed. Note :- The quoted rate of earthing shall be deemed to include galvanised iron strip 32x6mm, medium grade GI light grade 20 mm bore watering pipe. Any variation in length shall be adjusted through deviation order based on SSR rates adjusted with quoted rates.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x6 mm thick burried directly in gound (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to galvanised iron earth lead 4mm dia by means of bolt, nuts check nuts and washers of galvanised iron and 4 mm dia GI earth wire protected by provn of GI medium grade pipe 15mm bore upto 7.5mtr including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (Weight not less than 4kg/Sqm) and frame of angle iron 25x 25x3mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of Bronze/Gun metal with fixing arrangement, funnel, wire mesh and excavation/earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No 3 of SSR -2010 Part -I and connecting to earth test point all as specified or indicated including testing on completion, complete all as specified and directed. Note :- The quoted rate of earthing shall be deemed to include cost of 7.5 m long galvanised wire 4 mm dia and protection pipe 15 mm bore medium grade GI light grade 20 mm bore watering pipe. Any variation in length shall be adjusted through deviation order based on SSR rates adjusted with quoted rates.

Supply & fixing cubical type Cable junction box of size 260 x 210 x 116 mm fabricated out of 1.6 mm thick CRCA sheet juction box for street light pole mounted junction box/terminal box suitable for mounting on round pole and suitable arrangement for fixing bracket complete with one MCB 6 amps capacity single pole and suitable to terminate loop in/out cables upto 35 sqmm .

Supply and lay cable PVC insulated unsheathed of size 1.5 Sqmm 3 core copper conductor for service connections from junction box to light fitting.

Supply and replace GI pipe bracket ,made out of GI pipe 40 mm dia light grade 1.2mtr long bend to the shape 120 degrees angle including clamps-02 set made out of MS flat (50x6mm) duly bend to shape for PCC/steel tubular pole , nuts,bolts and washers etc, complete all as directed at site.

EXCAVATION AND EARTH WORK

Excavating in trenches in soft/ loose soil not exceeding 1.50 m wide and not exceeding 1.50 m in depth for foundation for pipes, walls, cesspits, manholes, pier holes, cables etc not exceeding 10 Sqm on plan and getting out complete all as specified.

Returning, filling in, spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each complete all as specified.

Removal of excavated soil to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

INTERNAL ELECTRIFICATION WORKS

Material & labour for point wiring with two single core 1.5 Sqmm (nominal cross sectional area) FRLS PVC insulated multi-stranded copper conductor cable in and including PVC casing & caping including fittings & accessories with pressed steel terminal boxes made of 1.6 mm thick MS sheet with 3mm thick plastic laminated bakelite (Hylum) sheet top cover for mounting switch socket etc including 1.5 Sqmm FRLS PVC copper conductor cable multi-stranded in green colour code as earth wire connected to the common earth dolly for one light or fan or one 2/3 pin socket outlet 5 amps (independent) or one bell/buzzer point controlled by one switch/push button, complete, all as specified.

All as per the description of Serial item No 7.01 above, but for one light point controlled by two 2 way switches.

Material & labour for point wiring with two single core 4 Sqmm (nominal cross sectional area) FRLS PVC insulated multi-stranded copper conductor cable in and including PVC casing & caping including fittings & accessories with pressed steel terminal boxes made of 1.6 mm thick MS sheet with 3mm thick plastic laminated bakelite (Hylum) sheet top cover for mounting switch socket etc including 4 Sqmm FRLS PVC copper conductor cable multi-stranded in green colour code as earth wire connected to the common earth dolly for one 3 pin socket outlet 15 amps on independent complete, all as specified.

Supply & fixing for Bell ding dong, AC, 230 volts single pole complete, all as specified.

Supply & fixing ceiling rose surface bakelite 3 terminals 65 x 50mm complete all as specified and directed.

Supply & fixing Switch Bell push, flush type, 5 amp complete all as specified and directed.

Supply & fixing switch piano, flush type, single pole, 1 way, 5 Amp, 240 volts complete all as specified and directed.

Supply & fixing switch tumbler water - tight, 5 Amps, single pole, one way mounted in cast iron or steel box for security lights complete all as specified and directed.

Supply & fixing switch socket combination 2-in-1, multipurpose, 5 pin, 5 & 15 Amp flush type universal complete all as specified and directed.

Supply & fixing switch socket combination 2-in-1, multipurpose, 5 pin, 5 Amp flush type complete all as specified and directed.

Supply and fixing sub main wiring with two run of 6 sqmm single core PVC insulated, unsheathed multistranded copper conductor cable 1100 volt grade, drawn through and including PVC casing caping including accessories fixed with cadmium plated steel screws to the surfaces/recesses of the wall/ ceiling including one run of 6 sqmm single core PVC insulated unsheathed copper earth continuity conductor complete all as specified and as directed. Notes : 1. Two runs of single core cable with one run of earth continuity conductor including PVC casing caping and accessories shall be measured and paid as one unit.

Supply and fixing sub main wiring with two run of 10 sqmm single core PVC insulated, unsheathed multistranded copper conductor cable 1100 volt grade, drawn through and including PVC casing caping including accessories fixed with cadmium plated steel screws to the surfaces/recesses of the wall/ ceiling including one run of 10 sqmm single core PVC insulated unsheathed copper earth continuity conductor complete all as specified and as directed. Notes : 1. Two runs of single core cable with one run of earth continuity conductor including PVC casing caping and accessories shall be measured and paid as one unit.

Supply and fixing sub main wiring with two run of 16 sqmm single core PVC insulated, unsheathed multistranded copper conductor cable 1100 volt grade, drawn through and including PVC casing caping including accessories fixed with cadmium plated steel screws to the surfaces/recesses of the wall/ ceiling including one run of 16 sqmm single core PVC insulated unsheathed copper earth continuity conductor complete all as specified and as directed. Notes : 1. Two runs of single core cable with one run of earth continuity conductor including PVC casing caping and accessories shall be measured and paid as one unit.

Supply and fixing 25 mm dia rigid, non-metallic PVC conduits for sub main cables, TV cables, Telephone cables, etc. exclusive of junction boxes but inclusive of all fittings such as tees, bends, elboes, reducers, bell mouth, tube ends and all fixing accessories such as couplers, lock nuts, saddles, pipe hook etc. Note :- 1. All conduit shall be concealed in alignment as directed by the Engineer in Charge. 2. The cable for telephone/TV shall be provided by users. 3. The electric sub main cables shall be measured and paid for separately.

Supply and fixing sheet metal enclosures single phase double door flush to wall fitted with 200 A rated bus bar and neutral link for MCB (without MCBs) 4 ways SPN complete all as specified and directed.

Supply and fixing sheet metal enclosures single phase double door flush to wall fitted with 200A rated bus bar and neutral link for MCB (without MCBs) 8 ways SPN complete all as specified and directed.

Supply and fixing sheet metal enclosures single phase double door flush to wall fitted with 200A rated bus bar and neutral link for MCB (without MCBs)12 ways triple pole and neutral (TPN) complete all as specified and directed.

Supply and fixing sheet metal enclosures single phase double door flush to wall fitted with 200A rated bus bar and neutral link for MCB (without MCBs)8 ways triple pole and neutral (TPN) complete all as specified and directed. Notes for Item No 7.15 to 7.18 : (a) DB should be suitable for IP-43 protection including provision for REVERSIBLE DOOR. (b) MCB shall be measured and paid for separately

Supply and fixing MCB, single pole & neutral 240 volts, capacity 6-32 Amps complete all as specified.

Supply and fixing MCB, single pole 240 volts, capacity 6-32 Amps complete all as specified.

Supply and fixing MCB, triple pole & neutral 415 volts, capacity 6-32 Amps, C series 50 Hz, 10 KA complete all as specified.

Supply and fixing MCB, Tripal pole & neutral 415 volts, capacity 63 Amps, C series 50 Hz, 10 KA complete all as specified.

Supply and fixing Single pole & neutral sheet metal enclosure (factory made) with a two pin and earth plug and socket complete with one single pole MCB, 240 volts 20 Amps complete all as specified.

Supply and fixing 1 X 22 W LUMILINE ENDURA LINEAR NEO Surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete all as specified. Make of Havells code no.ENDURALINEARNEOBS22WLED840SPCWH/Philips / Bajaj/Crompton

Supply and fixing 1 X 18 W LUMILINE Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver complete all as specified. Make of Havells code no.LUMILINEBS18WLED830SPCWH/Philips / Bajaj/Crompton

Supply and fixing LED Lamp 10 W complete all as specified. Make : Havells cat No. LHLDEREEMK8X015/ Philips / Bajaj/Crompton

Supply and fixing ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs 10W LED complete all as specified and as directed. Make : Havells Cat part. No RUGBYNEONFT10WLED760SSYMBOPC or equivalent in BAJAJ/PHILIPS/CG

Making arrangement for fixing of special light fitting (e.g chandeliers etc) on the ceiling by placing a MS hook on the ceiling all as directed by the Engr- in Charge.

Supply and fixing exhaust fan heavy duty steel body with louvers shutters complete of 200mm size with bolts,nuts and washers ,size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan for giving connection complete all as specified. Note: Cost of opening in wall and grouting of mild steel work shall be deemed included in the lump sum cost of the building.

Supply and fixing ELCB (RCCB), Double pole, 240 V, 300 mili Amps sensitvity, 25 Amps capacity with weather proof, factory made, sheet metal enclosure complete all as specified and as directed.

Supply and fixing batten holder PVC backellite body complete all as specified and as directed.

Supply and fixing switch piano, flush type single pole two ways 15 Amps complete all as specified and as directed.

Material and Labour for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to the galvanised iron or steel earth wire 4.00 mm dia, by means of bolts nuts check nuts and washers of galvanised iron and earth wire protected by provision of GI Medium grade pipe 15 mm bore including provisions of concrete pit in PCC 1:2:4 reinforced with XPM (weight not less than 4 kg/Sqm ) and frame of angle iron 25 x25 x6 mm with lugs 2 Nos and handle of 5 mm dia mS Bar made to shape, GI medium grade 20 mm bore pipe of watering perforated at bottom 1.75 metre long placed on top edge of earth plate, charcoal, common salt, test point made out of 40x 8 mm FI with fixing arrangements, funnel, wire mesh and earth works in hard/ dense soil, returning, fitting in and removal of surplus soil to a distance not exc 50 metre , all as per electric plate No 5 of SSR -1991 part-I connected to earth test point all as specified or indicated incl testing on completion complete all as specified and as directed.

EXTERNAL WATER SUPPLY WORKS

Supply, laying, jointing and testing steel water tubing galvanized, 20mm bore, medium grade, ISI marked with necessary fittings such as tees, elbows, bends, reducers, unions etc. laid in trenches, or laid under floors, fixed on walls with and providing clamps etc complete all, as specified and directed.

Supply, laying, jointing and testing steel water tubing galvanized, 25mm bore, medium grade, ISI marked with necessary fittings such as tees, elbows, bends, reducers, unions etc. laid in trenches, or laid under floors, fixed on walls with and providing clamps etc complete all, as specified and directed.

Supply, laying, jointing and testing steel water tubing galvanized, 40mm bore, medium grade, ISI marked with necessary fittings such as tees, elbows, bends, reducers, unions etc. laid in trenches, or laid under floors, fixed on walls with and providing clamps etc complete all, as specified and directed.

Supply, laying, jointing and testing steel water tubing galvanized, 50mm bore, medium grade, ISI marked with necessary fittings such as tees, elbows, bends, reducers, unions etc. laid in trenches, or laid under floors, fixed on walls with and providing clamps etc complete all, as specified and directed.

Supply and fixing for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 50mm dia complete all as specified and directed.

Supply and fixing for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20mm dia complete all as specified and directed.

Supply and fixing for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 25mm dia complete all as specified and directed.

Supply and fixing for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 40mm dia complete all as specified and directed.

Material and labour for construction of brick masonry valve pit of size 900 x 900 x 1500mm (internal size) with mild steel sheet cover 3.15mm thick and frame of angle iron of size 50x50x 6mm duly painted with two coats of synthetic enamel paint over a coat of red oxide primer including excavation and earth work in hard/dense soil,150mm thick PCC (1:4:8) type D-2 as in foundation,brick work in cement mortar (1:6),locking arrangement, and all inner size of pit shall be plastered 15mm thick in cement mortar (1:4) and coping in PCC (1:2:4) type B-1 over brick wall complete all as shown on the drawings as specified.

Material & labour for insulation of GI Pipe with PUF slab 30 mm thick of density 48 Kg/cum conforming to relevant IS, including insulationa around bends, elbows/tees with and including applying bituminuous compound and GI cladding with 26 gauge GI sheet complete size 25 mm bore etc complete all as specified and directed.

Material & labour for insulation of GI Pipe with PUF slab 30 mm thick of density 48 Kg/cum conforming to relevant IS, including insulationa around bends, elbows/tees with and including applying bituminuous compound and GI cladding with 26 gauge GI sheet complete size 20 mm bore etc complete all as specified and directed.

HOT WATER SUPPLY WORKS

Supply, fixing connecting and testing energy efficient (BEE 5 Star rated) electric water heater vertical storage type of 25 Ltrs capacity with stainless Steel inner tank, brass assembly, pressure release valve, heating element 1500 W including all other accessories with high quality external finishes, PVC connection of size 15 mm dia & 450 mm long with both ends,single phase with working voltage 240 volts, 50 Hz, ISI marked complete all as specified and directed. Notes : (a) The cost of fixing of geysers including stud/ nuts/fastners, bolts, washers and making good the disturbed surfaces to match with the existing surface is deemed to be included in the unit rate quoted. (b) The contractor shall provide two years maintenance spares.

Material & labour for lagging to pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 on pipe of internal dia 25 mm complete all as specified and directed.

Material & labour for lagging to pipes used in internal water supply or plumbing all round with, 25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 on pipe of internal dia 20 mm complete all as specified and directed.

M/S KASHCON CONSTRUCTION CO

CONSTRUCTION ENGINEERS