Construction of New Taluka Panchayat Office at Lunawada & Construction of New D Type TDO Quarters at Lunawada Ta. Lunawada Dist. Mahisagar

Name of Work :- (Package) Construction of New Taluka Panchayat Office at

Lunawada & Construction of New D Type TDO Quarters at Lunawada Ta.

Lunawada Dist. Mahisagar

BILL OF QUANTITIES

Memorandum showing item of works to be carried out.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

1 Excavation for foundation upto 1.50 mt depth including sorting out and stacking 1694.81 Cum 256.26

of useful materials and disposing the excavated stuff for all lead and lift for all

2 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 1167.83 Cum 273.59

and stacking of useful materials and disposing the excavated stuff with all lead

and lift for all sorts of soil.

3 Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 4 277.83 Cum 4352.09

graded stone aggregates 20 mm nominal size) and curing complete excluding

cost of formwork and reinforcement for reinforced concrete work in (A)

Foundations, footings, base or columns and mass concrete.

4 Providing and laying controlled cement concrete M-250 and curing complete 450.30 Cum 4916.96

including the cost of form work but excluding cost of reinforcement for reinforced

concrete work in Foundations, footings base of columns & mass concrete. (For

5 Providing and laying controlled cement concrete M-250 and curing complete 58.23 Cum 8438.74

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars, posts & struts upto floor two level.

Column upto plinth level.

6 Providing and laying controlled cement concrete M-250 and finishing smooth with 96.28 Cum 6053.94

curing etc. complete including the cost of formwork but excluding the cost of

reinforcement for R.C.C. work in Ground beams.

7 Filling available excavated earth (excluding rock) in trenches plinth side of 1652.76 Cum 136.92

foundation etc. in layer not exceeding 20 cm in depth consolidation each

deposited layer by ramming and watering etc. complete.

8 Filling in foundation and plinth with murrum or selected soil in layers of 20 cm 369.91 Cum 295.15

thickness including watering, ramming and consolidating etc. complete.

9 Filling in plinth with sand under floors including watering, ramming, consolidating 50.15 Cum 479.80

and dressing complete.

10 Anti-Termite System : Providing and laying of permanent piping technology anti- 804.77 Sq.m. 134.33

termite treatment before flooring work by installing LLDP (Low linear density

polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube, having working pressure of

Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-clips and nails. The LLDP pipe

shall be installed at the entire periphery of the building and at internal network of

building at a depth of 20 to 200 mm under floor at every 2 to 3 mtr. c/c distance

(adjusted as per building layout) & ends of loop pass through a PVC elbow of

minimum 32 mm ID at junction box of wall and floor level, entering into a steel

reinforced grooved flexible pipe of minimum 22 mm ID leading into junction box

and the loops shall terminate in junction boxes & test every junction during

injecting chemicals for termite control treatment.

The anti termite chemical Imidacloprid 30.5% SC mix as per IS-6313 (part III)

shall be injected by the pressure pump diluted with water @ 10.5 ml/5 ltr of water

at the rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit approved line

plan for piping system and junction boxes dully approved by Engineer-in-Charge

with bond of 5 year warranty. (i) Permanent pipe system with junction boxes

(Only pipe network)

11 Providing and laying damp proof course 25mm thick cement concrete 1:2:4 (1- 96.15 Sq.m. 321.97

Cement : 2 coarse sand : 4 stone aggregate 10 mm nominal size) and curing

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

12 Providing and laying brick work using common burnt clay building conventional 122.73 Cum 4214.33

type bricks having crushing strength not less than 35 Kg./Sq.cm. in foundation

and plinth in cement mortar 1:6 (1 cement : 6 fine sand) including the cost of all

materials and labour charges etc. complete. (For B/W Up to PL)

13 Providing and laying brick work using common burnt clay building conventional 278.13 Cum 4496.05

type bricks having crushing strength not less than 35 Kg/sq.cm. in super

structure above floor two level in cement mortar 1:6 (1 cement : 6 fine sand) for

Ground Floor & First floor including the cost of all materials and labour charges

14 Providing and laying brick work using common burnt clay building conventional 50.29 Cum 4538.16

type bricks having crushing strength not less than 35 Kg/sq.cm. in super

structure above floor two level in cement mortar 1:6 (1 cement : 6 fine sand) for

Second Floor including the cost of all materials and labour charges etc. complete.

15 Providing and laying half brick work using common burnt clay building 622.02 Sq.m. 684.26

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm in

cement mortar 1:4 (1 cement : 4 coarse sand) in super structure above floor two

level for Ground floor & First floor including the cost of all materials and labour

charges etc. complete.

16 Providing and laying half brick work using common burnt clay building 21.09 Sq.m. 690.57

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm in

cement mortar 1:4 (1 cement : 4 coarse sand) in super structure above floor two

level for Second floor including the cost of all materials and labour charges etc.

17 Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6 40.48 Cum 4147.33

crushed stone aggregates 20 mm nominal size) and curing complete including

cost of formwork in (A) Wall Caps / Coping

18 Providing and laying controlled cement concrete M-200 and curing etc. complete 33.80 Cum 7476.02

including the cost of form work but excluding the cost of reinforcement in Lintel

for Ground floor & First floor.

19 Providing and laying controlled cement concrete M-200 and curing etc. complete 2.29 Cum 7517.56

including the cost of form work but excluding the cost of reinforcement in Lintel

for Second floor.

20 Providing and laying controlled cement concrete work of M-200 and curing 5.01 Cum 8594.09

complete including cost of formwork and excluding reinforcement for reinforced

concrete work in (E) Staircases excluding landing upto floor two level for G.F. to

F.F. staircase.

21 Providing and laying controlled cement concrete work of M-200 and curing 3.90 Cum 8635.63

complete including cost of formwork and excluding reinforcement for reinforced

concrete work in (E) Staircases excluding landing upto floor two level for F.F. to

S.F. staircase.

22 Providing and laying controlled cement concrete M-200 and curing complete 77.29 Cum 7934.56

including the cost of formwork but excluding the cost of reinforcement for

reinforced concrete work in (D) Columns, pillars posts and struts, upto floor two

level. (Upto G.F. & F.F. Slab)

23 Providing and laying controlled cement concrete M-200 and curing complete 14.08 Cum 7976.10

including the cost of formwork but excluding the cost of reinforcement for

reinforced concrete work in (D) Columns, pillars posts and struts, upto floor two

level. (Upto S.F. slab)

24 Providing and laying controlled cement concrete M-200 & curing complete 108.04 Cum 6560.96

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Beam upto floor two level for G.F. & F.F. beam.

25 Providing and laying controlled cement concrete M-200 & curing complete 4.34 Cum 6602.50

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Beam upto floor two level for S.F. beam.

26 Providing and laying controlled cement concrete M-200 & curing complete 110.90 Cum 4877.29

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Slabs, landing, cantilevers upto floor two level for

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

27 Providing and laying controlled cement concrete M-200 & curing complete 187.87 Cum 7461.22

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Slabs, landing, cantilevers upto floor two level for

G.F. & F.F. slab.

28 Providing and laying controlled cement concrete M-200 & curing complete 5.36 Cum 7591.29

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Slabs, landing, cantilevers upto floor two level for

29 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work including 129178.47 Kg. 77.29

bending, binding and placing in position complete upto all floor level for Ground &

30 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work including 6599.00 Kg. 78.34

bending, binding and placing in position complete upto all floor level for Second

31 Providing and fixing M.S. Fan clamps type 1 to 16mm dia M.S. bar bent to shape 89.00 No. 136.75

with hooked ends to R.C.C. slabs curing, laying including painting the exposed

portion of loops, all as per standard design complete

32 Providing & fixing 40 mm thick Single shutter flush door solid core finished with 25.50 Sq.m. 7181.27

both side 1 mm thick lamination both side like 'NOVAPAN 'or equivalent of

natural wood grain shade as approved by this office having telephone black

granite 18 mm thick frame with double stone as per the instruction of Engineer in

charge with necessary SS hinges and fixtures etc. complete.

33 Providing & fixing 35 mm thick Single shutter flush door solid core finished with 94.64 Sq.m. 6741.16

both side 1 mm thick lamination both side like 'NOVAPAN 'or equivalent, of

natural wood grain shade as approved by this office having telephone black

granite 18 mm thick frame with double stone including fixed ventilation above

lintel level as per drawing and as per the instruction of Engineer in charge with

necessary SS hinges and fixtures etc. complete.

34 Providing and fixing FRP frame size 125 x 65 mm and 35mm thick FRP shutter 31.08 Sq.m. 2615.04

having extra reinforcement on sides & edges in polish finish. The core of the

shutter & frame is to be filed up with injected polyurethene foam done in situ

alongwith embedded wooden pieces for stiffening & also taking hinges & fixtures.

The whole FRP frame & shutter is to be water proof weather proof, termite proof

& resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & alluminium S.S. fixtures & fastenings & fastener sleeve.

35 Providing and fixing standard extruded colour anodized Alluminium section frame 86.40 Sq.m. 3490.56

(weight 1.094 Kg/Rmt.) with partly fixed and partly sliding shutter with of 5mm

thick transparent bronzed colour tinted float glass with transparent silicon gasket

with alluminium powder coated fittings and fixture (three track) and fixing to black

granite frame as per details and executed as per directed by Engineer in charge.

36 Providing and fixing standard extruded colour anodized Alluminium section frame 127.60 Sq.m. 3925.87

(weight 1.094 Kg/Rmt.) with partly fixed and partly sliding shutter with of 5mm

thick transparent bronzed colour tinted float glass with transparent silicon gasket

with alluminium powder coated fittings and fixture (two track) and fixing to black

granite frame as per details and executed as per directed by Engineer in charge.

37 Providing and fixing window having extruded aluminum colour anodized section 10.73 Sq.m. 3199.68

frame main outer size 95mm x 24mm x 1.17mm (@ Wt. 0.738 Kg/mt), horizontal

three track member size 92mm x 31.75mm x 1.30mm (@ Wt. 1.07 Kg/mt),

vertical member of size 92mm 31.75mm x 1.50mm (@ Wt. 1.06 Kg/mt) with

sliding shutters of horizontal member size 40mm x 18mm x 1.29mm (@ Wt. of

0.456 Kg/mt), vertical member of size 40mm x 18mm x 1.29 mm (@ Wt. of

kg / mt) with 5 mm thick transparent bronze colour tinted float glass with powder

coated aluminum fittings and fixtures and transparent silicon sealant glass fixing

including granite frame as per details etc. complete.

38 Providing and fixing M.S. grills of required pattern to wooden / Marble / Granite / 4543.14 Kg. 131.04

Stone frames of windows etc. with M.S. flats at required spacings and frame

alround, square or round bars with round headed bolts and nuts or by screws (A)

Ornamental Grill.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

39 Providing and fixing M.S. grills of required pattern to wooden / Marble / Granite / 4.89 Sq.m. 4456.12

Stone frames of windows etc. with M.S. flats at required spacings and frame

alround, square or round bars with round headed bolts and nuts or by screws (A)

40 Providing and fixing 144mm wide G.I. sheet having thickness of 0.55mm & 402.68 Kg. 130.29

weight not less than 490 gm/meter, roll formed to create 84mm wide louver snap

fixed on special G.I. channel fix louveres & channels shall finished with powder

coating of 5 micron as per directed by engineer incharge.

41 Providing and fixing louvered type ventilators with powder coated aluminum 11.16 Sq.m. 17418.85

fittings and fixtures and Blur glass fixing to adjustable louvers and black granite

frame as per details and executed as per directed by Engineer in charge.

42 Standard extruded colour anodized alluminium section frame (weight 1.094 16.34 Sq.m. 7676.00

kg/rmt) with continuous fixed glass 8mm thick clear float glass with transparent

silicon gasket.

43 Providing and laying Vitrified tiles 8 to 10 mm thick, 24''x 24'' in flooring treads of 681.02 Sq.m. 1120.36

steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-

coarse sand) finishing with flush pointing in white cement.

44 Providing and laying 24" x 24" vitrified 8 mm thick tiles flooring over 20mm 307.62 Sq.m. 1401.38

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new surface

or fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finished with flush

pointing & cleaning the surface etc. complete for light shade.

45 Providing and laying 24" x 24" vitrified 8 mm thick tiles flooring over 20mm 34.18 Sq.m. 1467.72

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new surface

or fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finished with flush

pointing & cleaning the surface etc. complete for Dark Shade.

46 Providing and laying 24" x 24" vitrified 8 mm thick tiles flooring over 20mm 387.26 Sq.m. 1467.72

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new surface

or fixing on existing flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry including finished with flush

pointing & cleaning the surface etc. complete for antiskit.

47 Providing and laying marble stone slab flooring over 20mm (average) base of 120.34 Sq.m. 2241.52

cement mortar 1:6 (1 cement : 6 coarse sand) or L.M.1:1.5 (1 lime putty :

coarse sand) laid and jointed with gray cement slurry including rubbing and

polishing complete. (A) Marble slab 25mm thick

48 Providing and laying Vitrified tiles 8 to 10 mm thick, 24'' x 24'' in skirting, risers of 61.29 Sq.m. 1195.02

steps and dedo on 10mm thick cement plaster 1:3 (1 cement : 3 coarse sand)

and jointed with white cement slurry.

49 Providing and laying polished Kota stone slab flooring over 20mm (average) thick 4.22 Sq.m. 1019.39

base of cement mortar 1:6 (1-cement : 6 coarse sand) or L.M. 1.1.5 (1-Lime putty

:1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with

pigment to match the shade of slab including rubbing and polishing etc.

complete. (A) 25mm thick

50 Providing and laying 18 mm thick machine cut, free edges, machine polished 11.97 Sq.m. 3325.93

Black Granite tread and risers in single piece with 1 cm nosing and necessary

grooves on treads etc. complete.

51 Providing and laying broken china mosaic flooring for terrace using 12 mm to 20 661.81 Sq.m. 779.70

mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar creme out upto surface using white

cement including rounding off junctions and extending them upto 15 cm along the

wall, clearing with water and oxalic acid etc. as directed.

52 Providing and laying BBCC of 75mm thick layer in CM (1:3) including spraying 718.18 Sq.m. 634.77

two coat of water proofing chemical with selected brand by enginner in charge

i.e. perma or other with leveling complete for ready base of china mosaic

53 Providing and cement vata (10cm x 10cm size) quarter round in cement mortar 295.44 Rmt. 24.28

1:1 including neat cement finishing watering etc. complete.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

54 Providing 20 mm thick double coat mala cement plaster on interior brick / 2465.94 Sq.m. 283.95

concrete work for plastering comprising of base coat of 12 mm thick cement

plaster in cement mortar (1 cement : 4 coarse sand) in rough finishing and 8 mm

thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished with

trowel including scaffolding, curing etc. complete. (For Interior plaster for G.F. &

55 Providing 20 mm thick double coat mala cement plaster on interior brick / 48.05 Sq.m. 311.18

concrete work for plastering comprising of base coat of 12 mm thick cement

plaster in cement mortar (1 cement : 4 coarse sand) in rough finishing and 8 mm

thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished with

trowel including scaffolding, curing etc. complete. (For Interior plaster for S.F.)

56 Providing 15mm thick cement plaster in single coat on brick/concrete walls for 1109.17 Sq.m. 201.44

interior plastering upto floor two level and finished even and smooth in cement

mortar 1:4 (1 cement : 4 sand) for ceiling for G.F. & F.F.

57 Providing 15mm thick cement plaster in single coat on brick/concrete walls for 29.92 Sq.m. 223.33

interior plastering upto floor two level and finished even and smooth in cement

mortar 1:4 (1 cement : 4 sand) for ceiling for S.F.

58 Providing 20mm thick sand faced cement plaster on walls upto height 10 metres 2797.64 Sq.m. 373.17

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement

: 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc.

complete including galvanised iron chicken mesh complete. (For Exterior plaster).

59 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 342.98 Rmt. 43.05

60 Applying two coats of putty & two coats of primer of approved brand and 2635.21 Sq.m. 40.59

manufacture on new wall surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and other foreign matter and

sand papered smooth.

61 Applying two coats of putty & two coats of primer of approved brand and 1139.09 Sq.m. 42.77

manufacture on new wall surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and other foreign matter and

sand papered smooth. (Ceiling Putty)

62 Wall painting two coats with plastic emulsion paint of approved brand and 2635.21 Sq.m. 82.85

manufacture on wall surfaces to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign matter and sand

papered smooth.

63 Finishing wall with weather proof exterior emulsion paint on wall surface (two 3742.21 Sq.m. 120.26

coats) to give an required shape even shade after thoroughly brushing surface to

remove all dirt, dust and remains of loose powdered materials etc. complete.

64 Wall painting two coats with plastic emulsion paint of approved brand and 3575.08 Sq.m. 85.03

manufacture on wall surfaces to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign matter and sand

papered smooth on ceiling.

65 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. U.P.V.C 252.00 Rmt. 148.12

pipe (Sch-40) for cold water including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every two meter c/c or shall

be concealed as directed including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent including cost of all

66 Providing, laying and jointing in true line and level I.S.I. mark 32mm dia. U.P.V.C 385.00 Rmt. 119.15

pipe (Sch-40) for cold water including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every two meter c/c or shall

be concealed as directed including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent including cost of all

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

67 Providing, laying and jointing in true line and level I.S.I. mark 15mm dia. U.P.V.C 492.50 Rmt. 72.65

pipe (Sch-40) for cold water including fitting as approved by Engineer in charge.

Pipe shall be fixed on the wall with held of clamp at every two meter c/c or shall

be concealed as directed including necessary fitting etc. including testing of pipe

and joints and fixing the same with adhesive solvent including cost of all

68 Providing and fixing concealed center point to wall, ceiling and floor I.S.I. mark 182.00 Rmt. 660.58

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for

potable water of following dia. nominal bore tube fittings and clamps including

making good the wall, ceiling and floor etc. complete. (F) 50 mm dia.

69 Providing and fixing concealed center point to wall, ceiling and floor I.S.I. mark 260.00 Rmt. 253.82

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for

potable water of following dia. nominal bore tube fittings and clamps including

making good the wall, ceiling and floor etc. complete. (B) 25 mm dia.

70 Providing, laying and jointing in true line and level I.S.I. mark 110mm diameter 526.00 Rmt. 876.90

U.P.V.C. SWR Type B pipe confirming to IS 13592 -1992 with one end plain and

other end socketed with rubbering & fitting confirming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the

size 110mm diameter x 149mm length x 145mm high at every 2000mm center to

center or shall be concealed in wall as directed including necessary fitting such

as bends, shoes etc. including testing of pipe and joints and jointed with adhesive

solvent cement including cost of all materials.

71 Providing, laying and jointing in true line and level I.S.I. mark 160mm diameter 258.00 Rmt. 834.38

U.P.V.C. (Type B) confirming to IS 13592 -1992 with one end plain and other end

socketed with rubbering & fitting confirming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be jointed with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160mm

diameter x 210mm length x 196mm high at every 2000mm center to center or

shall be concealed in wall as directed including necessary fitting such as bends,

shoes etc. including testing of pipe and joints and jointed with adhesive solvent

cement including cost of all materials.

72 Providing and fixing screw down bib taps of following size (A) Brass chromium 57.00 No. 186.83

plated screw down bib tap (i) 15mm dia. as approved by Engineer in charge for

73 Providing and fixing screw down bib taps of following size (A) Brass screw down 61.00 No. 214.81

bib tap polished bright (ii) 20mm dia. as approved by Engineer in charge for all

74 Providing and fixing pillar tap, capstan head screw down high pressure with 54.00 No. 354.69

screw, shanks and back nuts (B) 20mm dia. as directed by Engineer in charge.

75 Providing and fixing chromium plated brass half turn flush cock of approved 59.00 No. 263.77

quality including fixing in pipe line etc. complete. (ii) 25mm dia. as directed by

Engineer in charge.

76 Providing and fixing Gun metal check or non return full way wheel valve. 40 mm 19.00 No. 663.43

77 Providing and fixing Gun metal check or non return full way wheel valve. (C) 25 20.00 No. 420.63

78 Providing and fixing wash basin with single hole for pillar tap with C.I. or M.S. 19.00 No. 1451.48

brackets painted white including cutting holes and making good the same but

excluding fittings. (A) Vitreous china (ii) Flat Back washbasin 550 mm x 400mm

size. (i) In white colour.

79 Providing and fixing Table top basin having granite of 18 to 20 mm thick having 6.00 No. 9231.40

minimum single piece length of 210 mm to be fixed on walls to act as study table

/ wash basin, including fixing the same using cement mortar in proportion 1:1 etc.

complete necessary groove in walls by machine, front side round the edge and

cutting hole in granite stone for washbasin / Computer wire, including rubbing

and polishing finishing jointed with grey cement slurry including rubbing and

polishing finishing etc. complete with all labour & material & equipment etc.

completed as directed by Engineer-in-charge (A) Granite slab 18mm thick.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

80 Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed 26.00 No. 616.42

to wooden plugs with C.P. brass screws.(B) 600 mm x 20 mm size.

81 Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 1.00 No. 282.16

100mm dia. each

82 Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass 25.00 No. 859.41

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden plug

with C.P. brass screws and washers.

83 Providing and laying wash down water closet (European type Wall hung W.C. 15.00 No. 10271.70

pan) Florentine series FLS-WHT 0111B including providing and fixing metropole

flush cock seat cover, jet wash etc. complete unit of jaquar branch (or equivalent)

including installing and fitting as per manufacturers standards by skilled trained

plumber including testing etc. complete quality and brand as approved by

Engineer in charge.

84 Providing and fixing water closet squatting pan (Indian type W.C. pan) size 4.00 No. 995.50

580mm (Earthwork, bed concrete, foot rest and trap to be measured and paid for

separately) (A) Vitreous china. (I) Long pattern white colour.

85 Providing and laying wash down water closet with all accessories for disable 1.00 No. 20806.00

person (European type Wall hung W.C. pan) Florentine series FLS-WHT 0111B

including providing and fixing metropole flush cock seat cover, jet wash etc.

complete unit of jaquar brand (or equivalent) including installing and fitting as per

manufacturers standards by skilled trained plumber including testing etc.

complete quality and brand as approved by Engineer in charge.

86 Providing and fixing Urinal of approved quality including connection with trap and 8.00 No. 1635.22

with integral longitudinal flush pipe. (A) Squatting plate pattern white earthenware

87 Providing and fixing PVC SWR Nahni Trap IS 14735 for drain with jail of the 71.00 No. 586.27

following nominal diameter of self cleansing design with C.I. screwed down of

hinged grating including the cost of cutting and making good the walls. (i) 100mm

88 Providing and laying (to level or slopes) and jointing with stiff mixture of cement 37.00 Rmt. 317.46

mortar in proportion 1:1 salt glazed stone ware pipes following nominal internal

diametre including testing of pipes and joints etc. complete. 150 mm dia.

89 Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brick 5.00 No. 3457.27

bats with dry masonry work at top for 45cm. height including covering the top with

stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as

90 Constructing brick masonary chamber for under ground C.I. Inspection chamber 34.00 No. 2932.93

and bends with bricks having crushing strength not less than 35 Kg/cm2 in C.M.

1:5 C.I. cover with frame (light duty) 455 mm x 610 mm. internal dimensions,

total weight of cover with frame to be not less than 38 Kgs. weight of cover

Kg. and wt. of frame 15 Kg) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm. size) foundation concrete 1:5:10 inside

plaster 15 mm. thick with cement mortar 1:3 finished smooth with a floating coat

of neat cement on walls & a bed concrete etc. complete. (i) inside dimension

455mm x 610 mm and 450mm deep for single pipe line.

91 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand 6.00 No. 11042.74

: 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-

cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm

thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating

coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement : 2-Coarse sand :4-stone aggregate 20mm nominal size) finished

smooth complete including curing and festing (i) Inside size 900mm x 1200mm

and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight

of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of

frame 64 Kg.) (A) With 230mm thick walls of brick masonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement

: 5 Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

92 Providing erecting and fixing double coated Syntex or equivalent PVC (I.S.I.) 13000.00 Litre 3.95

mark water tank of required capacity each with all necessary fittings & connection

etc. comp on terrace.

93 Providing and fixing ball cock of approved quality as directed. (A) Copper metal 5.00 No. 132.89

94 Providing and laying sandwich type kitchen platform of size 2.10 x 0.76 x 0.76 m 7.36 Sq.m. 19282.34

and respected length with dhar polish or moulding having base 4" and support &

base with marble or kota as per site requirement also loft and base finish with

glaze tile and top with selected shed of marble or granite with gas pipe provision

and sink including all fittings, material and labour as per directed by Engineer

95 Providing & fixing Co2 type portable ABC Dry Powder type ABS Fire extinguisher 35.00 No. 3535.00

capacity 4.5 Kg. discharge range 3mt. timing 60 to 180 sec. standard approved

IS code No. 2878:2004.

96 Clearing and grubbing road land including uprooting rank vegetation grass 0.51 Hect. 84255.99

bushes, shrubs, sapling and trees girth up to 300 mm removal of stumps of trees

cut earlier and disposal of unserviceable materials (A) By manual means in area

of light jungle.

97 Providing and fixing precast Rubber dye / steel dye inter locking concrete block 204.10 Sq.m. 706.77

60mm thick with grade of concrete M-300 pneumatic compressed / vibrated

mechanically and as per approved design confirming to IS 15658 : 2006 including

35 mm sand layer for levelling and filling the joint with sand in proper line and

level as per guidelines of IRC : SP 63-2018 etc. complete.

98 Providing and fixing precast concrete kerb stone of grey cement based concrete 203.25 Rmt. 402.55

block 30 cm length, 30 cm height and 15 cm thick of M-200 grade concrete as

per approved design and including excavation for fixing in proper line and level,

filling the joints with C.M. 1:3 (1 cement : 3 fine sand) etc. complete.

99 Providing and laying Precast RCC Perforated Jali 100mm thick 750 mm x 750 124.00 Sq.m. 402.55

mm including transportation, loading, unloading or as per detailed drawing.

100 Providing and fixing 90 cm high Stainless steel railing made from anticorrosive 36.73 Rmt. 3162.31

S.S. pipe of 50 mm dia (16 Gauge) as hand rail with S.S. 38 mm dia. (16 Gauge)

as a vertical support fixed in RCC slab at 1.2m c/c including three horizontal S.S.

pipes of 25 mm dia. (16 gauge) at equal distance fixed by 18.75 mm dia (16

gauge) S.S. pipe including accessories as per detailed drawing as directed etc.

101 Supply and fixing the SS letter finish with chromium and height is not less than 79.00 No. 1515.00

10" SS made of 304 and surface should be reflective type (including all labour,

material, fixing, transportation and CNC cutting) and Item should be executed as

per directed by engineer in charge.

102 Constructing brick masonry chamber for underground C.I. Inspection chamber 2.00 No. 3660.76

and bends with bricks having crushing strength not less than 35Kg./cm2 in C.M.

1:5 C.I. cover with frame (Light duty) 455mm x 610mm internal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and

Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1-cement :2- coarse sand :4-

graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x

700 mm and 450mm deep for pipe line with one or two inlets.

103 Providing and laying C.I. steps 50cm x 15cm. 2.25cm. and C.I. cover suitable 2.00 No. 6303.41

frame with necessary fixtures and joint and finish complete. (Including sump step

in staggered form including two coat of oil paint)

104 Providing and fixing of submersible motor of required quality and with control 2.00 No. 9595.00

panel of 1.00 HP etc complete with having outlet 25 mm dia.

105 Providing & fixing to wall, ceiling and floor galvanized mild steel tubes (medium 30.00 Rmt. 608.35

grade) of the following nominal bore, tube fittings and clamps including making

good the wall, ceiling and floor (E) 40mm.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

106 Providing and laying cement concrete 1:5:10 (1-Cement : 5 fine sand :10 graded 36.00 Rmt. 213.71

stone aggregate 40mm nominal size) bedding for stoneware pipes of following

internal diameters with necessary formwork and curing complete.(B) 150mm dia.

(166mm avg. bed thickness)

107 Extra over item 24.1 for providing salt glazed stoneware fittings. (i) Bends of 10.00 No. 63.79

required degree (any radious) of following nominal diameters. (B) 150mm dia.

108 Providing and laying marble chips skirting (Terrazo) or dedo rubbed and polished 81.54 Sq.m. 653.09

to Granolithic finish top layer 6mm thick with white, black or white and black

marble chips of size from smallest to 4mm nominal size laid in cement marble

powder mix 3:1 (3- cement : 1 marble powder by weight) in proportion of 4:7 (4-

cement marble powder mix : 7-marble chips by volume) 20mm thick with under

layer 14mm thick cement plaster 1:3 (1-cement : 3-coarse sand) (A) Dark shade

pigment with ordinary cement (In top layer only)

109 Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and 30.80 Cum 182.94

stacking of useful materials and disposing off the excavated stuff upto 50 Meter

lead (B) Dense or Hard soil.

110 Providing and laying controlled cement concrete M-150 for curing complete 6.20 Cum 4022.72

excluding cost of formwork and reinforcement for reinforced concrete work in (A)

Foundations, footings, base of columns and mass concrete.

111 Half brick thick honey comb brick work with common burnt clay building bricks 138.08 Sq.m. 322.96

having crushing strength not less than 35 Kg/Sq.cm. (i) In cement mortar 1:4 (1

cement : 4 coarse sand)

112 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not 4.00 No. 958.17

less than 35 Kg.

113 Providing, laying (to level or slopes) and jointing reinforced concrete light duty 98.00 Rmt. 257.19

non-pressure pipes I.S. class NP-2 of the following internal diameter with collars

and butt ends prepared for collar joints including testing of joints complete. (B)

114 Constructing brick masonry chamber for underground C.I. Inspection chamber 4.00 No. 7180.44

and bends with bricks having crushing strength not less than 35 Kg/Cm2 in C.M.

1:5 C.I. cover with frame (light duty) 455mm x 610mm internal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and

Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand :

graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete. (iii) Inside dimensions 600mm

x 850 mm and 450mm deep for pipe lines with three or more inlets.

115 Providing, laying (to level or slopes) and jointing reinforced concrete light duty 60.00 Rmt. 359.84

non-pressure pipes I.S. class NP2 of the following internal diameter with collars

and butt ends prepared for collar joints including testing of joints complete. (C)

116 Filling in foundation and plinth with brick bats, chhara in layers of 20cm. thickness 12.40 Cum 621.46

including watering, ramming and consolidating etc. complete.

117 Providing and fixing PVC SWR Nahni trap IS-14735 for drain - 75 mm diameter 20.00 No. 574.58

with jali of the following nominal diameter of self cleansing design with C.I

screwed down or hinged grating including the cost of cutting and making good

118 Providing, fixing and erecting steel shed including M.S. G.I. pipe (class-B), 343.95 Sq.m. 3957.18

framing of structure with hollow section and painting with two coats of oil paint

including priming coat. Rates including with necessary fabrication work including

cutting, welding, making holes by drilling machine & fixing in line and level of all

structure including cost of all laboures, fixtures, fastening and equipments etc.

119 Providing and laying brick work using common burnt clay building conventional 85.33 Cum 4526.81

type bricks having crushing strength not less than 35 Kg./Sq.cm. in foundation

and plinth in cement mortar 1:5 (1 cement : 5 fine sand) including the cost of all

materials and labour charges etc. complete.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

120 Providing 20mm thick cement plaster in single coat on single or half brick walls 1105.57 Sq.m. 223.82

for interior plastering upto floor two level and finished even and smooth in cement

mortar 1:4 (1 cement : 4 sand)

121 Providing and laying and fixing 50 mm thick expansion joint by hydro cell semi 16.19 Sq.m. 1491.03

rigid UV resistance with high performance laminated closed cell polythene foam

joint filler in sheet foam as directed etc. complete.

122 Providing and fixing M.S. grill entrance gate of predetermine design including all 21.00 Sq.m. 4454.10

material like hinges, roller, stopper, rail head, handle etc. having coat of red lead

and painting with selected colour guide by engineer incharge.

123 Providing and filling in foundation with ordinary cement concrete M-150 mix and 23.00 Cum 3711.75

providing necessary vertical pin headers including formwork, vibrating, ramming

and curing complete.

124 Providing and casting in situ controlled cement concrete M-250 for R.C.C. Raft 26.00 Cum 4721.75

and cutt-off walls including necessary shuttering, laying, vibrating, ramming and

curing complete.

125 Providing & casting in situ ordinary cement concrete M-250 mix and providing 38.00 Cum 4393.50

necessary pin headers including shuttering, scaffolding, laying, vibrating, curing

and finishing complete without V-grooves. (A) Height from 0.0 M. to 5.0 M.

126 Providing and laying in position I.S.I. mark Fe 500D T.M.T. bar reinforcement 3.20 M.T. 73858.70

including cutting, bending, hooking and tying complete as per detailed drawings

for the following. (A) Piers (B) Abutments (C) R.C.C. Returns

127 Constructing Manhole with R.C.C. top slab in 1:1.5:3 mix (1 cement : 1.5 coarse 1.00 No. 50197.00

sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete

(P.C.C) 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) brick work using burnt clay building bricks having crushing strength

not less than 35 kg/Sq.cm with cement mortar 1:6 in side plastering 15mm thick

with cement mortar1:3 (1 cement : 3 coarse sand) finished smooth (i) In side size

2100 mm x 1300 mm and 2.46 mt depth or as per site condition and drawing

including precast cover without frame size 750 x 750 mm (heavy duty M-10) C.I.

steps 150 mm c/c alternate as per detailed drawing.

128 Providing and laying half brick work using common burnt clay building 59.18 Sq.m. 750.76

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm in

cement mortar 1:3 (1 cement : 3 coarse sand) with 2 nos. of 6mm mild steel

round bars after every three course embedded in cement mortar in super

structure above plinth level upto floor two level including the cost of all materials

and labour charges etc. complete.

129 Providing 15mm thick cement plaster in single coat on rough (similar)side of 199.22 Sq.m. 175.39

single or half brick walls for interior plastering upto floor two level and finished

even and smooth in cement mortar 1:4 (1 cement : 4 sand) (Interior plaster)

130 Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles 47.44 Sq.m. 1674.15

having Tegular edge & 15 mm thick densified edges on the Tile Periphery for

extra strength. The light weight calcium silicate ceiling tiles shall have , light

reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity0.043° w/m KC.for the best

thermal Insulation. The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & globe having

NRC value of 0.75 NRC or equivalent of size 595 x 595 mm to be laid on true

horizontal level suspended inter locking metal grid of hot dipped galvanized steel

sections (galvanizing @120 grams per sqm including both side) consisting of

main ‘T’ runner suitably spaced at joints to get required length and size of 24 x

38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre and

cross ‘T’ of size 24 x 28mm made out of 0.33mm (Minimum) sheet spaced

1200mm along spaced between main ‘T’ at 600mm centre to centre to form a

grid of 1200 x 600mm and secondary

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

cross ’T’ of length 600mm and size 24 x 28mm made of 0.30 mm thick

(Minimum) sheet to be interlocked at middle of the 1200 x 600mm panel to form

grid of size 600 x 600mm resting on periphery walls/partitions on a perimeter wall

angle pre-coated steel of size (24 x 24 x 3000mm made of 0.40mm thick

(minimum) sheet with the help of rawl plugs at 450mm centre to centre with

25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified

edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured

/ Cosmos / Spintone) in the grid including cutting / making opening for services

like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever

required, Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats

of size 25 x 35 x 1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash

fasteners, 4mm G.I. adjustable rods with galvanized steel level clips of size 85 x

30 x 0.8mm, spaced at 1200mm centre to centre long main ‘T’ bottom exposed

with 24mm of all T-sections shall be

pre-painted with polyester baked paint, for all heights, as per specifications,

drawings and as directed by engineer-in-charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall.

No deduction shall be made for exposed frames / opening (cut outs) having area

less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC. Value of

0.50 (Minimum) for Fine fissured / Spintone / Cosmos and 0.75 NRC for Globe,

light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity. 0.043° w/m KC for the best

thermal Insulation.

131 Drilling of 215mm dia. bore in over burden strata (0-30) including lowering and 75.00 Mtr 383.00

fixing of 175 mm nominal dia UPVC pipe/175 mm dia ERW pipe upto required

depth and further drilling of 165mm dia bore hole in rocky strata by DTH rig.

132 Providing & supplying 175mm nominal dia. UPVC “CS” type pipe as per IS:12818 30.00 Mtr 906.00

and as per detailed technical specification.

133 Electric motor driven borewell submersible pump set conforming to I.S. 8034 and 1.00 Set 18756.00

motor conforms to IS-9283 working at 3 phase 400/440 volt 50 C/S A.C. supply &

2900 R.P.M. discharge 240 LPM and 72 mtr Head, 7.5 hp Cat.

134 SITC of D.O.L starter up to 7.5 H.P. 1.00 Set 8383.00

135 Providing & supplying Flat PVC cable size 4.0 sq.mm as per IS 694 with BIS 60.00 Mtr 87.00

mark and as per detailed technical specification.

136 Heavy duty, 50 mm dia. G.I. Column pipe both end threaded having length 60.00 Mtr 537.00

approximate 3 mtr. confirming to IS 1239 (Part-1) with coupling at one end.

137 Providing, supplying and fitting ISI mark CI D/F Sluice Valves as per IS:14846 1.00 No. 2316.00

(Latest Edition) of following class and diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. PN-1 With hand

wheel /cap operated (PD type short body) 50 mm

138 Providing, supplying & fitting ISI mark CI D/F Reflux Valves as per IS:5312 1.00 No. 3307.00

(Latest Edition) of following class and diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. Reflux valves PN

IS 5312 with ISI mark 50 mm

139 Lowering of Submersible motor pump set complete with required nos and size of 1.00 Job 2500.00

Column pipe erected by means of proper chain pulley block & pipe wrenches

after checking of threads of each pipe with coupling to take the load of the

pumpset and pipe assembly filled up with water with trail testing..

140 Clamps made from MS plate with 3 holes on either side with nuts & bolts of 1.00 No. 560.70

standard make and suitable size 450 mm x 65 mm x 10 mm flat suitable to

141 Supply of TOP & BOTTOM accessories of 50 mm dia. 1.00 No. 1475.00

142 R&B Approved make ELCBs / RCCBs conforming to IS:12640 and having 1.00 No. 2213.00

sensitivity of 30 mA and Short Circuit with stand capacity of 10 KA and suitable

for operation on 3 phase and neutral 415V. having characteristic of quick action &

tripping with all advance feature & do not incorporate any electronic component

for following Max. rating erected as directed. 40 Amp. Cat.III

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

143 Electrical wiring & fitting charges of electric meter, 40Amp fuse, control panel etc. 1.00 Job 2500.00

including erection of the above items on wooden board, cost of material and all

liasioning work for getting electric connection from concerned Vij Company.

144 Pumping test of the tubewell by sub mersible pump of adequate capacity for 165 1.00 Job 17250.00

145 Providing and fitting readymade prefabricated portable chemicalized ferro 1.00 Job 12187.50

concrete mini panel having outer size 110 x 50 x 190 cm with necessary fitting for

electic panel mounting complete as per detailed specification and drawing.

146 Three Phase GEB power charges. 1.00 Job 14000.00

Electrical Items

147 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 269.00 Pt 485.81

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth continuity of following type, erected on

PVC / Metallic / Wooden box, single mounting base frame covered with textured /

metallic / white front plate modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III (Make:- Pipe : Precision / Polycab / Vraj / Nihir /

Astral, Wire: Polycab / RR Kabel / KEI / Finoloex / Havells, Accessories: Havells /

Anchor / Greatwhite / Vinay)

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall 4.00 Pt 242.91

/ ceiling complete Cat. III (Half Point for Bathroom and WC) (Make :- Pipe :

Precision / Polycab / Vraj / Nihir / Astral, Wire: Polycab / RR Kabel / KEI /

Finoloex / Havells, Accessories: Havells / Anchor / Greatwhite / Vinay)

148 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both 77.00 Pt 674.68

are of ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan regulator mounted and accessories

with earth continuity of following type erected on PVC / Metallic / Wooden box,

single mounting base frame covered with textured / metallic / white front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling

rose / H.D. Connector as directed.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat. III (Make :- Pipe :

Precision / Polycab / Vraj / Nihir / Astral, Wire: Polycab / RR Kabel / KEI /

Finoloex / Havells, Accessories: Havells / Anchor / Greatwhite / Vinay)

149 Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth 13.00 Pt 167.66

wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection with primary light with

accessories erected on Metal / PVC / wooden box covered with 3 mm thick

PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed.(f) with medium class

Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

(Make :- Pipe : Precision / Polycab / Vraj / Nihir / Astral, Wire: Polycab / RR Kabel

/ KEI / Finoloex / Havells, Accessories: Havells / Anchor / Greatwhite / Vinay)

150 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of 26.00 Pt 510.05

ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with Modular type switch &

pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe erected with following type

of accessories.[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from

nearby switchboard/mcb db board (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat. III (Make :- Pipe :

Precision / Polycab / Vraj / Nihir / Astral, Wire: Polycab / RR Kabel / KEI /

Finoloex / Havells, Accessories: Havells / Anchor / Greatwhite / Vinay)

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db 5.00 Pt 745.38

board. (f) with medium class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete Cat. III (Make :- Pipe : Precision / Polycab / Vraj / Nihir /

Astral, Wire: Polycab / RR Kabel / KEI / Finoloex / Havells, Accessories: Havells /

Anchor / Greatwhite / Vinay)

151 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket 123.00 Pt 257.55

erected on PVC / Metallic / Wooden box, single mounting base frame covered

with textured / metallic / white front plate modules erected on / in wall / ceiling

with following type accessories Cat. III (Make :- Havells / Anchor / Greatwhite /

152 Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 8.00 Pt 603.98

1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires erected in below type of pipe with 6A Modular type

switches and following type of accessories erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured / metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected with necessary

batten/angle holder or ceiling rose or H.D. Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

Cat. III (Make :- Pipe : Precision / Polycab / Vraj / Nihir / Astral, Wire: Polycab /

RR Kabel / KEI / Finoloex / Havells, Accessories: Havells / Anchor / Greatwhite /

153 Providing following type of Modular Type Accessories mounted with PVC / 32.00 Ea 160.59

metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate, modules erected with necessary connections as per

site situation directed by Engineer in charge. (3) Two Pin/RJ-11 Telephone

Socket [A] For One Gang Cat. III (Make :- Havells / Anchor / Greatwhite / Vinay)

(4) TV Co-axial Socket outlet Cat. III (Make :- Havells / Anchor / Greatwhite / 1.00 Ea 160.59

(5) Electronic hum Free steps EME Fan regulator Cat. III (Make :- Havells / 2.00 Ea 398.95

Anchor / Greatwhite / Vinay)

(7) Blank Plate Single Cat. III (Make :- Havells / Anchor / Greatwhite / Vinay) 135.00 Ea 25.25

(8) Computer RJ-45 socket Cat. III (Make :- Havells / Anchor / Greatwhite / 67.00 Ea 160.59

(9) 16 Amp. SP one way switch Cat. III (Make :- Havells / Anchor / Greatwhite / 24.00 Ea 180.79

(10) 6/16 Amp. Universal socket Cat. III (Make :- Havells / Anchor / Greatwhite / 24.00 Ea 199.98

154 Providing & erecting following type of Modular Type Accessories with necessary 67.00 Ea 36.36

connection as desired by Engineer In charge (5) LAN cable connector with ferule.

155 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following 2028.00 Mtr. 24.24

size complete to be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & Clamps with following dia

of pipes, in approved manner as directed (a) 20 mm (Make :- Precision / Polycab

/ Vraj / Nihir / Astral )

(b) 25 mm (Make :- Precision / Polycab / Vraj / Nihir / Astral ) 509.00 Mtr. 33.33

(c) 32 mm (Make :- Precision / Polycab / Vraj / Nihir / Astral ) 10.00 Mtr. 54.54

156 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 19.00 Mtr. 62.62

stranded Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of following size

(A) With medium class Rigid PVC pipe and accessories (Make :- Pipe: Precision

/ Polycab / Vraj / Nihir / Astral, Wire: Polycab / RR Kabel / KEI/ Finolex / Havells)

(b) 2 wire 2.5 sq. mm (Make :- Pipe: Precision / Polycab / Vraj / Nihir / Astral, 2494.00 Mtr. 82.82

Wire: Polycab / RR Kabel / KEI/ Finolex / Havells)

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

157 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 388.00 Mtr. 112.11

stranded Copper conductor wire in following type of pipe to be erected in / on wall

/ ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size (A) with medium class Rigid

PVC pipe and accessories (a) 2 wire 4 sq. mm (Make :- Pipe: Precision / Polycab

/ Vraj / Nihir / Astral, Wire: Polycab / RR Kabel / KEI/ Finolex / Havells)

(b) 2 wire 6 sq. mm (Make :- Pipe: Precision / Polycab / Vraj / Nihir / Astral, Wire : 18.00 Mtr. 147.46

Polycab / RR Kabel / KEI/ Finolex / Havells)

(h) 4 wire 6 sq. mm (Make :- Pipe: Precision / Polycab / Vraj / Nihir / Astral, Wire: 200.00 Mtr. 260.58

Polycab / RR Kabel / KEI/ Finolex / Havells)

(i) 4 wire 10 sq. mm (use earth wire of 4 sq.mm) (Make :- Pipe: Precision / 70.00 Mtr. 425.21

Polycab / Vraj / Nihir / Astral, Wire: Polycab / RR Kabel / KEI/ Finolex / Havells)

158 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi 16.00 Mtr. 37.37

stranded, annealed copper conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required. (d) One wire 4.00 sq.mm

(e) One wire 6.00 sq. mm 20.00 Mtr. 56.56

(f) One wire 10.00 sq. mm 5.00 Mtr. 91.91

(h) One wire 25.00 sq. mm 3.00 Mtr. 236.34

(i) One wire 35.00 sq. mm 2.00 Mtr. 300.98

(k) One wire 70.00 sq. mm 1.00 Mtr. 669.63

159 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv 106.00 Mtr. 46.46

grade ISI marked copper wires of following size to be erected as directed. (e)

1.50 Sq.mm 3 core round PVC sheathed.

160 Providing & erecting approved make following size of TV Co-axial flexible cable 12.00 Mtr. 62.62

comprising inner conductor of solid bare copper insulated with Foam PE &

Secondary conductor made of poly - Aluminium film bonded Al Braids @ suitable

coverage overall sheathed with black PVC insulation. (e) RG-11

161 Supplying & erecting approved make Telephone Cable electrolytic copper 632.00 Mtr. 20.20

conductor PE insulation twisted in two pairs & wrapped with FRLS PVC tape &

sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring &

confirming to C-DOT erected in existing pipe. of following size of conductors &

nos.of pairs with necessary connections.[A] Conductor Size 0.5 mm (a)

Unarmoured (2) Two Pairs

(5) Ten Pairs 100.00 Mtr. 65.65

(6) Twenty Pairs 5.00 Mtr. 127.26

162 Supplying & erecting approved make LAN cable of following size in existing pipe 1876.00 Mtr. 47.47

as per direction [C] CAT -

163 Providing & erecting main Distribution (MDF) indoor type, back mounted frame as 4.00 Ea 994.85

per DoT standard approved with krone strips (a) Suitable for 10 pair

(b) Suitable for 20 pair 1.00 Ea 1368.55

(c) Suitable for 50 pair 1.00 Ea 1747.30

164 Providing & erecting Switch board for Computer or electric apparatus consisting 69.00 Ea 1133.22

of following modular type accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary connections

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III (Make :- Havells /

Anchor / Greatwhite /Vinay)

165 Bakelite adopter for Holder to be erected. 118.00 Ea 9.09

166 Decorative call bell Ting-tong box type 250 volts complete erected 15.00 Ea 71.71

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

167 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 118.00 Ea 373.70

Watt assembled on single MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%, CCT

K to 6500K, Luminaire efficacy> 85 lumens/watt, LED

LED driver efficiency > 85 % (fitting required LM-79 & LM-80 Certificates) (NOTE:

Below description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges shown)

(A) Tube Light with integral driver (iv) 22-24 Watts, Surge - 2KV, IP-20,

conventional 4 feet Cat-lll ( Make :- Phillips, Havells, OSRAM, Crompton, Wipro,

168 Supplying and erecting led lamps with following wattage capacity of 220 to 240 30.00 Ea 188.87

voltage, minimum 15000 burning hours life, 500 V in built-surge protection,

Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >=

0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP holder (iii)

to 15 watts Cat-lll

169 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 42.00 Ea 427.23

Watt assembled on single MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die

cast powder coated and high U.V. & corrosion resistance with diffuser housed

in aluminium casted body with company mark / name 160V to 270V,Power

Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy>

85 lumens/watt, LED driver efficiency > 85% (fitting required LM-79 & LM-80

certificates) (NOTE: Below description have shown ranges of Wattage capacity of

LED fittings. The Engineer incharge may select any wattage capacity between

the ranges shown) (A) Square/ Circular shaped Surface / Recessed Mount

Downlight with provision for spring loaded mounting clips complete. IP20 (ii) 11-

15 watts, Surge-2 KV Cat-lll (Make :- Phillips, Havells, OSRAM, Crompton,

(iv) 22-24 watts, Surge-2 KV Cat-lll (Make :- Phillips, Havells, OSRAM, 61.00 Ea 758.51

Crompton, Wipro, Jaguar)

(B) LED Panel Light with provision for Plane front frame with translucent cover 9.00 Ea 724.17

fixed to housing complete. IP20 (v) 24 watts, 12" x 12", Surge-2 KV Cat-lll (Make

:- Phillips, Havells, OSRAM, Crompton, Wipro, Jaguar)

170 Supplying and erecting LED street light / Flood light fittings with High power 22.00 Ea 4997.48

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V, Power Factor

more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio > 0.45,

Luminaire efficacy> 100 lumens/watt. LED driver efficiency > 85%. (fittings

required LM-79 & LM-80 certificates) (NOTE: Below description have shown

ranges of Wattage capacity of LED fittings. The Engineer incharge may select

any wattage capacity between the ranges shown) (A) Street Light (IP-65), Surge

protection -4KV integral and Light must have 440VAC line supply with over-

voltage protection. (ii) above 48 to 60 Watts Cat-lll (Make :- Phillips, Havells,

OSRAM, Crompton, Wipro, Jaguar)

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and 2.00 Ea 4819.72

spun aluminum canopy fixed with opal polycarbonate, pipe arrangement for

vertical mounting driver and accessories wired upto terminal block.IP 65 (ii) 32-

40W Cat-lll (Make :- Phillips, Havells, OSRAM, Crompton, Wipro, Jaguar)

171 Providing and erecting Approved make Four pole moulded case circuit breaker 4.00 Ea 6173.12

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C.

supply 50 c/s. with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.ICS=100% of ICU only. Cat III (Make :-

L&T, Havells, C&S, Indoasian)

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

172 Providing and erecting Approved make Four pole moulded case circuit breaker 1.00 Ea 16221.61

having breaking capacity ICU of 35 KA. at 415 V. having Normal current rating

200A.with variable Thermal & magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned copper & complete erected in

existing 16 G.M.S.housing ICS=100% of ICU only. Cat III (Make :- L&T, Havells,

C&S, Indoasian)

173 Providing and erecting Approved make Earth fault Relay suitable to mount with 1.00 Ea 4687.41

inter connection suitable to following size of moulded case circuit breaker having

CT ratio & MCCB rating as following along with shunt trip 220V AC. with all

internal connections & complete erected in existing M.S.housing. (1) 15 A -100

A, CT Ratio 1/100

174 Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper 0.40 Rn. 1961.42

Busbars with four equal Nos. of electrolyte bus having current density not more Mtr.

than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with

colour insulating tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable socket to each

bar, erected in existing cubical panel with necessary connections.(A) Suitable for

100 Amp. Capacity

(B) Suitable for 200 Amp. capacity 0.50 Rn. 3202.71

175 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system 24.00 Ea. 270.68

and having breaking capacity 10 KA to be erected in existing box. confirming to

IS 8828/1996 with ISI Mark Cat III (Make :- L&T, Havells, C&S, Indoasian)

176 Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to 120.00 Ea. 112.11

operate on 240 V A.C. system and having breaking capacity 10 KA to be erected

in existing box confirming to IS 8828/1996 with ISI Mark Cat III (Make :- L&T,

Havells, C&S, Indoasian)

177 Providing & erecting 240 V MCB double pole switch for motor & inductive load 5.00 Ea. 299.97

(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity (B) 40 Amp. Cat III (Make :- L&T, Havells, C&S,

(B) 40 Amp. Cat III (Make :- L&T, Havells, C&S, Indoasian) 11.00 Ea. 330.27

178 Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve) 8.00 Ea. 278.76

having 10 KA breaking capacity & confirms to IS : 8828 in existing box having

following capacity (A) 6 to 32 Amp. Cat III (Make :- L&T, Havells, C&S,

179 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) 15.00 Ea. 578.73

having 10KA breaking capacity & confirms to IS :8828 in existing box having

following capacity (A) 6 to 32 Amp. Cat III (Make :- L&T, Havells, C&S,

(B) 40 Amp. Cat III (Make :- L&T, Havells, C&S, Indoasian) 4.00 Ea. 638.32

180 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C 14.00 Ea. 668.62

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity (b) 40 Amp. Cat III (Make :- L&T, Havells, C&S,

(c) 63 Amp. Amp. Cat III (Make :- L&T, Havells, C&S, Indoasian) 4.00 Ea. 737.30

181 Sheets steel powder coated enclosure suitable for incorporating One/Two nos. 5.00 Ea. 176.75

182 Providing and erecting Sheet Steel powder coated MCB distribution board - flush 1.00 Ea. 1152.41

/ surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate

nos. of MCBs. (The DBs should be used of same company of MCB to be used)

suitable for (A) single phase incoming and horizontal single phase outgoing (b)

sheet steel double door (IP-43) (iii) 8 way (Make :- L&T, Havells, C&S, Indoasian)

(v) 16 way (Make :- L&T, Havells, C&S, Indoasian) 1.00 Ea. 1680.64

(B) three phase incoming and single phase horizontal type outgoing Per phase 9.00 Ea. 2339.16

isolation type (PPI) (b) sheet steel double door (i) 4 way (Make :- L&T, Havells,

C&S, Indoasian)

(ii) 6 way (Make :- L&T, Havells, C&S, Indoasian) 2.00 Ea. 2913.85

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

183 Providing and erecting Approved make RCCBs conforming to IS: 12640 and 18.00 Ea. 1969.50

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz. having characteristic of quick

action & tripping with all advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed (i) 25 Amps. DP Cat III

(Make :- L&T, Havells, C&S, Indoasian)

(ii) 40 Amps. DP Cat III (Make :- L&T, Havells, C&S, Indoasian) 16.00 Ea. 2235.13

184 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 3.00 Kg. 794.87

185 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. 2.00 Ea. 368.65

galvanised iron pipe with coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

186 For using salt and charcoal / coke as required for pipe type earthing. 2.00 Ea. 171.70

187 Supplying & erecting earth pit of minimum bore dia.150mm size approved make 3.00 Ea. 4591.46

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation suitable

for following type of applications with chamber and heavy duty cover. (A)

(approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer Incharge

has to ensure the value of earthing resistane mentioned in test Certificate) &

having back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- <

volt at no load & dry form, Sulphar content:- <2% (C) Back fill Compound :-

Earthing compound should be capable to retain moisture for long time necessary

test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

188 Providing and erecting Steel cover as per drawing using 16 SWG M.S.sheet of 0.20 Sq. 2560.35

following depth, to house the switch gear etc. complete with locking arrangement Mtr.

and lock with duplicate keys per cupboard and door handles erected with

necessary support and painting. [One coat red oxide and two coat enamel paint]

(B) Without angle iron frame (i) For 25 cms. depth

189 Providing and erecting Meter cover made from multi chamber hollow PVC 1.20 Sq. 3339.06

sections of 20 mm thick having all the corner joints with PVC solution angles Mtr.

without using any screws, nails shutters having required size of eye glass and

with necessary locking arrangement hinged with box. The back of meter box

should be fixed with timber. Hold fast for holding screws or nut bolts.

190 Providing & erecting weather proof, dust & vermin proof, floor mounted front 2.00 Sq. 16323.62

operated outdoor type double door cubical panel board necessary IP-54 and Mtr.

above protection as per approval from engineer incharge made from 14 SWG

thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories, supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses /

MCB for measuring instruments, earth bus & earth bolts, foundation flange -

bolts-base Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket, heavy duty end terminal connection, danger

notice board, necessary ventilation, earthing strip complete.

The Panel shall be painted with epoxy powder coating. (The rates excludes the

cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips,

meters, fuses etc. The dimension shall be measured excluding base beams) The

panel shall be supplied with following approved manufacturers with following size.

(B) The standard companies switch gear shall be used and only manufacturers at

CPRI approved factory (i) with 350mm depth

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

191 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable Aluminium 90.00 Mtr 92.92

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables. (B) 2 core 6 Sq.mm (Make :- Finolex, RR

Kabel, Havells, Polycab, KEI)

(C) 2 core 10 Sq. mm (Make :- Finolex, RR Kabel, Havells, Polycab, KEI) 85.00 Mtr 126.25

192 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 10.00 Mtr 220.18

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (B) 3 1/2 core 35 Sq.mm (16 Sq.

mm 1/2 core) (Make :- Finolex, RR Kabel, Havells, Polycab, KEI)

(D) 3 1/2 core 70 Sq. mm (35 Sq.mm 1/2 core) (Make :- Finolex, RR Kabel, 38.00 Mtr 378.75

Havells, Polycab, KEI)

193 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / 185.00 Mtr 126.25

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables (B) 4 core 6 Sq. mm (Make :-

Finolex, RR Kabel, Havells, Polycab, KEI)

(C) 4 core 10 Sq. mm (Make :- Finolex, RR Kabel, Havells, Polycab, KEI) 12.00 Mtr 140.39

194 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand 43.00 Mtr 153.52

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (A) 4 core 16 Sq. mm (Make :-

Finolex, RR Kabel, Havells, Polycab, KEI)

195 Making trench in soft soil of suitable width of 90 cm deep for laying cable or 296.00 Mtr 55.55

locating the fault all over the run and back filling the same and making the

surface as normal ground.

196 Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground 5.00 Mtr 226.24

across the road crossing or on floor with necessary material in an approved

manner and making the ground as per original.(F) 100 mm dia.

197 Providing & laying approved make Double walled corrugated pipes (DWC) of 341.00 Mtr 62.62

polyethylene (conforming to IS 14930 II) with necessary connecting accessories

of same material at required depth in existing trench for laying of cable below

ground / road surface for enclosing cable (A) 50 mm outer dia.

(B) 63mm outer dia. 31.00 Mtr 73.73

198 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for 48.00 Ea 38.38

PVC insulated armoured cable complete with out going tails, insulating tape etc

for following size of cables.(B) 2 to 4 core 6 Sq.mm

(C) 2 to 4 core 10 Sq.mm 6.00 Ea 38.38

(D) 2 to 4 core 16 Sq. mm 2.00 Ea 47.47

199 Providing and, fixing heavy duty flange type brass double compression type 2.00 Ea 75.75

cable gland with rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.(B) 3 & 1/2 core 35/50

200 Solder less crimping type Aluminium lugs conforming to IS suitable for cable of 152.00 Ea 6.06

following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass / cadmium plated nut bolts in an approved manner. (A) 1.5/

201 Providing & erecting Approved make Ceiling Fan with double ball bearing with 3.00 Ea 1982.63

Condenser 230 volt A.C.50 Hz. 900 mm sweep complete having 3 Aluminium

blades, canopy erected complete. [ Make shall be approved by Engineer in

Charge] (Make :- Havells, Orient, Crompton, Bajaj)

202 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with 66.00 Ea 1948.29

double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm

sweep complete having 3blades with aluminium blades with, canopy & 30 cm.

down rod erected with earthing. (Make shall be approved by Engineer in charge)

(Make :- Havells, Orient, Crompton, Bajaj)

203 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down 69.00 Mtr 108.07

rod erected duly painted for fan complete with proper insulation without leakage

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

204 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the 85.00 Ea 108.07

RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S.

box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary

205 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 85.00 Ea 18.18

206 Supplying & erecting approved make low noise decorative exhaust fan having 22.00 Ea 1703.87

square frame ABS body with inbuilt lowers & square frame. 200mm with

1350RPM Cat.II (Make :- Havells, Orient, Crompton, Bajaj)

207 Supplying and erecting approved make Octagonal pole made from HR sheet 14.00 Ea 6874.06

steel. The pole should be made as per IS and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard

profile 35mm x 7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected with suitable foundation

(Included) as per details given by manufacturer considering site requirement. (C)

5 Mtr. Long 70 mm Top x 130 mm bottom dia, 3 mm thickness with 200mm x

200mm x 12mm base plate, 4-M16 bolts and 600mm long with necessary G.I. J

Bolts. Approx Pole weight 46 kg

208 Supplying & erecting approved make SMC press moulded composite FRP. loop- 10.00 Ea 476.72

in, loop-out approx. 2mm thick box complete with Bakelite connector strip 5way

(3P+N+E), DIN rail for mounting mob & hinged doors as per requirement having

locking arrangements with mounting clamp with nuts, bolts & washers suitable for

erection on pole with cable clamps& earth bolt of following size of box. (C)

150mm x 125mm x 100mm [deep]

209 Providing and erecting street light pole bracket comprising main B Class GI pipe 14.00 Ea 614.08

of 4.2 cm/require outside dia. complete with suitable B Class G.I sleeve tubing of

approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top

having sufficient fasteners for fixing the brackets and having spread of 1 mtr.

length with suitable rise as per site condition & suitable welded stiffener reducer

and nipple with check nut complete painted with one coat of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint with following nos of arms.[A]

Single Arm bracket 1 Mtr.

210 Supplying and erecting B class Galvanized iron pipe having smooth finished bore 16.00 Mtr. 215.13

of the pipe on both ends erected nuts and bolts along the pole / wall shaping the

pipe as per site requirement. Pipe dia as following.(B) 32 mm dia

211 Supplying & erecting IP 55 grade following size section pillar fabricated from joint 1.00 Ea 3595.60

less M.S. Sheet with angle iron legs made from jointless M.S. Angle with cable

clamps to be buried in ground to have appropriate erection to work uniform until

erected with cement concrete foundation and 45 cm high bricks work finishing

with plaster etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in duplicate 35 x

x 5 mm M.S. Angle of Two Nos. one is welded and other with nut and bolt for

erecting Bakelite sheet. Painting the Section Pillar inside and out side with three

tank powder coated paint. section pillar roof should be without joint with water

leakage proof & tested as per IP 55 test & followed by IS 2147 of 1962 (B) 75 x

60 x 45 cm section pillar fabricated from 16 Gauge MS Sheet with angle iron legs

45 cm long made from 35 x 35 x 5 mm thick MS angle.

212 Supplying and erecting HYLAM sheet on existing angle iron frame.for following 1.20 Sq. 771.64

thickness (B) 4mm Mtr.

213 Supplying & erecting approved make Digital time switch having lithium cell 6 2.00 Ea 3168.37

years operative and operate battery backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A with, floating contacts

Minimum switching setup time 1 minimum & LCD display. Also comprised

permanent ON/OFF switching. Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as required with necessary

connection erected as directed.

214 Supplying & erecting power contactor, AC3 duty for time switch complete erected 1.00 Ea 796.89

as per direction Cat III (A) 2 Pole 250V 12 Amp.

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

215 SITC of Digital / PCM / TDM EPABX System having SMT design, system with 1.00 Ea 51440.31

flexible universal slots. Inbuilt Auto attendant facility, Minimum 15 Nos.

conference, Analog extension line, Calling GSM, E&M line, PRI / EI & VOIP

program me through Analog telephone digital key from Ethernet, public address

cord, shall have unrestricted simultaneous dialing facility, QSIG protocol on PRI,

95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-Single Digit dialing of

any two external number, Once only ring device, Chairman / Secretary - Do not

disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night

Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call transfer while

Ringing with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI

Base routing Internet Ready Port, External Music Port, Call Budgeting, Call Most

Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax

Homing, Global Directory Printing with following capacities.

[Approved by Competent Authority i.e. not below the rank of Executive Engineer]

[B] No of Extension 24, No of Junctions 9, 8 Port IP Resource in-built, 4 Port

Web base Video Conferencing, No of expandable ports : 96, Operators Console -

01 Compatible : ISDN

216 Providing & erecting water cooler having storage capacity 150 Ltr. & cooling 1.00 Ea 55893.40

capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the

water should drop by 15˚C within a hour, The water cooler should be comprising

of hermetically sealed compressor, fan motor, condensing unit, water tank

surrounded by evaporating, coil, thermostats, relay etc.complete with necessary

inlet & outlet connection. The body of water cooler will be made from Stainless

Steel. (Make :- Usha, Voltas, Bluestar)

217 Supplying & erecting 5 stage single reverse osmosis water purification system 1.00 Ea 29187.99

with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter

GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with

psi inline type post carbon filter auto low & high pressure switches with following

size of storage tank & LPH capacity & erected as directed [C] 50 Ltr / Hr with

psi 2 nos booster pump.

218 Supplying and erecting approved make panel mounting type Digital Voltmeter 1.00 Ea 1275.63

having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel

board with all connection, wiring etc .with manufacturers calibration certificate.

219 Supplying and erecting approved make panel mounting type Digital Ammeter 1.00 Ea 1558.43

having 3 digits LED display, external CT operated, calibrated for 0 to 1000 Amps

suitable to operate on 500 Volt AC, erected on existing panel board with all

connection, wiring etc. with manufacturers calibration certificate.

220 Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC 2.00 Ea 317.14

Supply 500 V on existing panel board with necessary connections.

221 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 3.00 Ea 274.72

ratio 15 VA burden erected in existing CRCA box duly secured with insulating

materials connected to the meter.

222 Supplying and erecting approved make suitable panel indicator LED type lamp, 9.00 Ea 43.43

lens cover, complete erected with necessary connections.

223 Providing & erecting open well type horizontal mono block pump set with 1.00 Ea 9613.18

stainless steel body having following specification (C) 1 H.P. single phase open

well motor pump set suitable for 185 LPM discharge @ 25 mtr. head, suitable for

32 mm dia. Delivery pipe with control panel.Cat. II

224 Providing & erecting open well horizontal mono block pump set with cast iron 1.00 Ea 15707.52

body, complete for three phase submersible motor having [C] For 3 HP 3 phase

open well horizontal mono block pump set suitable for 85 LPM to 270 LPM @

mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe Cat.II

It. Description of Item Qty. Unit Rates in Total

No. Figure Amount

225 Supplying & erecting approved make motor control cubical panel (Direct - on - 1.00 Ea 7722.46

line) made from 16 G. CRCA sheet duly epoxy powder painted inside and outside

with hinged doors and locking, arrangement consisting of suitable size of ON-

OFF isolator (AC - 3/23duty) main fuses, single phasing preventer, indicating

lamps for R- Y - B phases, overload relay, Automatic water level controller,

Ammeter, Voltmeter each with two way selector switch incoming, wires duly

socket crimped, main contactor & overload relay, start - stop push buttons, to be

erected on angle iron frame grouted on wall as directed. The isolator, overload

relay & contactors will be of L & T, Siemens or BCH make only. (A) DOL up to

226 Lowering of submersible motor pump set at the depth of following complete with 2.00 Per 856.48

required. Nos. and size of casing pipes erected by means of proper chain pulley Job

block & pipe wrenches after checking of threads of each pipe with coupling to

take the load of the pump set and pipe assembly filled up with water (D) For

Open well Horizontal submersible pump set for sump well (i) 1 HP to 5 HP.

227 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 32.00 Mtr. 104.03

Submersible copper cable approved make of following Size. (B) 3 Core x

i.e. Rs. Three Crore Ninety Five lacs Seventy Four thousand Nine hundred One and Twenty One paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is

a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as

directed and to be approved from the Engineer in charge.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Panchayat (R & B) Sub Division, Panchayat (R & B) Division, Panchayat (R & B) Division,

Lunawada Lunawada Lunawada