Construction of Govt. I.T.I. Building at Baijnath Distt Kangra. H.P.

Amount

Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavation earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation,. Footings bases of columns and mass concrete including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in all floor level including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor in all floor level. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate also including octroi, royality, GST, toll tax, Sale Tax or other taxes imposed by the government.

Providing form work with steel plates of 3.15mm (three decimal fifteen milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing form work with steel plates of 3.15mm (three decimal fifteen milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors all level and walls up to any width. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing form work with steel plates of 3.15mm (three decimal fifteen milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing form work with steel plates of 3.15mm (three decimal fifteen milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying cement concrete 1:6:12 (One cement isto six sand isto twelve aggregate) graded crushed/broken stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight aggregate) graded crushed/broken stone aggregate 40mm (fourty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated plain cement concrete work grade M-20 with cement contents and not less than 320 Kg/m3 (three hundred twenty) kilograme per cubic meters and curring complete. Excluding the cost of form work in foundation and plinth including entire carriage of material with all lead and lifts and other incidental as per specification, approved drawings design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compreasive strength of M-20 N/mm2 with cement contents not less than of 330kg/m3 (three hundred thirty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in foundation footing, basis of columns and the like mass concrete in all depth / thickness upto all floor level and curing complete including entire carriage of material within all leads, lifts and other incidental as per approved specificatioin, drawing, design as per direction of Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:5 (one cement isto five sand) and curing complete including carriage of materials within all leads and lifts complete in all respect as per the direction of Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts upto floor all level and curing complete as per specification, approved drawing, desing, including carriage of material within all leads, lifts and other incidental and as directed by Engineer-in-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in suspended floor, roofs, landing and shelves and their support balconies beams girders bressumers and cantilevers upto floor all level and curing complete including carriage of material within all leads, lifts and other incidental as per approved drawing, specification, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landing but including preparing of top surface and finishing of nosing upto all floor level and curing complete including carriage of material within all leads, lifts and other incidental as per approved specification, drawing design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc. from foundation upto all floor level and curing complete including entire carriage of material within all leads, lifts and other incidental as per specification, approved drawing, design and as directed by Engineer-in-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) including cost of form work but excluding cost of reinforcement for reinforced concrete work in Mouldings as in cornices windows sills etc. exceeding 15cm (fifteen centimeter) in girth and curing complete up to all floor level, as per specificatioin, aproved drawing, design and as per direction of Engineer-in-Charge including entire carriage of material with in all lead, lift and other incidential. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320 Kg/m3 (three hundred twenty kilogramme per cubic metre) mechanically mixed and vivrated and curring complete for reinforced cement concrete in chajjas for all thickness in all floor level up to all heights including finishing the exposed surface with cement motor 1:3 (one cement is to three sand) to give a smooth and even surface including centiring, form work but excluding the cost of reinforcement. As per specification, approved drawing, desing including entire carriage of material with in all lead and lift and other incidential as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing expension joint system related with wall joint (internal/External) location as per drawing and direction of Engineer-in-charge. The joint should be filled up with polyseterence back or rod base member, self alligning/centering arrangenment and support application both new and existing construction in office building and complexes with no slipping down tendency amongst the components system. The joint system shall utilized light weight with polysterence back or rod surface mechanically snap locking the multicellular to facilitate movement as per specification, drawing and including entire carriage of material all lead and lifts and other incidental. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing tor steel of Sail, Tisco reinforcement for reinforced cement concrete work including bending, binding cutting strengthening including placing in position complete, cost of binding wire up to floor all level as per specification, approved drawing, design as per entire satisfaction of Engineer-In-Charge including carriage of material with all lead and lift and other incidental. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying damp proof course 100mm (tundred milimetre) thick with cement concrete 1:2:4 (one cement isto two sand isto four aggregate) graded crushed/broken stone aggregate 12.5mm (tewelve decimal five milimeter) nominal size mechanically mixed and curing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Applying a coat of hot bitumen (mexphalt) 80/100 (Eighty by hundred) or equivalent using 1.70 kg (one decimal seven zero) kilogram per square meter on damp proof course after cleaning the surface with a piece of cloth lightly socked with kerosene as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Second class brick work using common burnt clay building bricks in cement mortar 1:6 (one cement isto six sand) in super structure up to any floor level and curring complete including carriage of material with in all lead and lift and other incidental as per approved specification, drawing and as directed by Engineer in Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Second class half brick work using common burnt clay building bricks in cement mortar 1:4 (one cement isto four sand) with hoop iron in super structure up to any floor level and curing complete including carriage of material with in all lead, lift and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded stone aggregate 20mm (twenty) millimeter nominal size mechanical mixed in cement mortor 1:6 (one cement six sand) including curring and carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:6 (one cement : six sand) and curing complete including carriage of materials within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing angle iron door,window,clerestory window frames (Single rebate) manufactured from M.S. Angle section of 35X35X4mm (thirty five by thirty five by four milimeter ) and M.S. Flat 50X4mm (fifty by four milimeter) thickness including hinges, jamb, lock, jamb, beed and if required thrashold of MS flat 50 X 5 mm (fifty by five milimeter)welded or regidly fixed by mechanical means lugs with spit ends and tails to each jamb including steel but hinges 2.50mm (two point five zero milimeter) thick with a provision of locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pre-treatment of the surface as per PWD specification, drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing angle iron door,window,clerestory window frames (Double rebate) manufactured from M.S. Angle section of 35X35X4mm (thirty five by thirty five by four milimeter ) and M.S. Flat 50X4mm (fifty by four milimeter) thickness including hinges, jamb, lock, jamb, beads and if required thrashold of MS flat 50 X 5 mm (fifty by five milimeter)welded or regidly fixed by mechanical means lugs with spit ends and tails to each jamb including steel but hinges 2.50mm (two point five zero milimeter) thick with a provision of locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pre-treatment of the surface as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing M.S. Channels for doors, windows, frames manufactured from M.S. Section 40x75x5mm (forty by seventy five by five milimeter) with MS flat 75x5mm (Seventy five by five milimeter) in combination as per drawing and design including hinges, jamb, lock jamb, beed and if required tharshold including tharshold of MS angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm (two point five milimeter) thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of surface as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing angle iron frames manufactured from M.S.Angle iron section 25X25X5mm thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 25mm (twenty five milimeter) thick water proof commercial board of century ply / kit ply / Dura ply / Marino ply in shelves/box for cup board with butt joints & fixing with nails & screws etc complete) with 6mm (six millimeter) thick hard wood edging all round. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 6 mm (Six millimetre) thick ply wood lining with butt jointing and nails (frame work and cove fillets to be measured and paid for separately) as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing factory made PVC door frame of size 50x47mm (fifty by forty seven milimeter) with a wall thickness of 5mm (five milimeter) out of extended 5mm (five millimeter) rigid PVC foam sheet mitred at corner and joint 2 Nos (two numbers) of 150mm (one hundred and fifty milimeter) long brackets of 15x15mm (fifteen by fifteen milimeter) M.S. Square tube the vertical door profiles to be reinforced with 19x19mm (Ninteen by Ninteen milimeter) M.S. Sheets 19G (ninteen gauge) of Rajshri Code No. 16.24 or its equalents complete as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 30mm (thirty milimeter) factory made PVC pannel per door shutter consisting frame made out of M.S. Tube and 19 Gauge (Ninteen gauge) thickness and size of 19x19mm (Ninteen by Ninteen milimeter) for single and 15x15mm (fifteen by fifteen milimeter) for top and botton rails code of 9.120 of Rajshri or to equvalant as per PWD specification drawing and design.The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 25mm thick (Twenty five milimeter) thick water proof commericial board of century ply / kit ply / dura ply / Morino ply (ISI marked) with 6 mm (Six milimeter) thick hard wood edeges all around and PGI sheet lining in side for SDB shutter as per PWD Specification drawing and design. including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 25mm thick Commercial Board of century ply / kit ply / duro ply water proof shutters for cup boards including fixing with nickel plated piano hinges with screws etc complete including 6mm (six millimeter) thick hard wood edging all round . The rates are inclusive cost as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing plain grills of required pattern in steel frames of windows etc. with M.S. flats, square or round bars with round head bolts and nuts or by screw. plain grill as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing factory made double steel shutter side hungs (one glazed and one wire gauge) of standred rolled steel section, joining mitered welded with manufactured to relevent ISI standred specification with steel plugs and screws or rawl plugs screw or with fixing clips or with bolt and nuts as as required and iron fitting including providing and fixing glass pans with special putty of glazed side of shutter and wire gauge of IS designation 85G (eighty five) with metal beading on other side complete including priming coat of red lead paint including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing steel glazed fixed window of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (Sixteen by three point one five milimeter ) lugs 10 cm. (ten centimeter ) long embedded in cement concrete blocks 15 cmx10cmx10cm (fifteen centimeter by ten centimeter by ten centimeter ) of 1:3:6 (one cement isto three sand isto six graded stone aggregate) 20mm nominal size (twenty milimeter) or with plug and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing steel glazed top hung windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (Sixteen by three point one five milimeter ) lugs 10 cm. (ten centimeter ) long embedded in cement concrete blocks 15 cmx10cmx10cm (fifteen centimeter by ten centimeter by ten centimeter ) size of 1:3:6(one cement isto three sand isto six graded stone aggregate) 20mm nominal size (twenty milimeter) or with plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per PWD specification including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 1.00mm thick coloured or plain lamination sheet(ISI marked) (sunmica) on boards with approved adhesive and nails etc including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing glass panes of modiguard, atul 5mm (five milimeter) plain glass fixed with putty & nails etc. Complete weight not less then 10kg (ten kilogramme) per Square meter including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing glass panes 4mm (four milimeter) thick frosted glass fixed with putty & nails etc. Complete weight not less then 10kg (ten kilogramme) per Square meter including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 35 mm thick flush door shutter both side commerical phenal bonded (century / ALPRO / Duroply of no 15 - 2202) core of board constructed with 1st class hard wood well matched with commericial board / ply veneering with veritical grains of cross bands and face veneering on both face shutters as per approved specification, drawing, design, including entire carriage of material with all lead lifts and other incidental. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing RCC Jali manufactured with M-25 (M-twenty five) grade or cement concrete fixing in position with cement mortor 1:4 (One cement isto four sand). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge as per PWD specification, drawing and design. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. 300x16mm (Three hundred into sixteen milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. 250x16mm (Two hundred fifty into sixteen milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete 250x10mm (Two hundred fifty into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete 100x10mm (Two hundred into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete.125mm (one hundred twenty five milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete.100mm (one hundred milimeter) nominal size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 200mm (two hundred milimeter) oxidized MS (mild steel) hooks and eyes as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Prokviding and fixing 65x35mm. (Sixty five into thirty five)special quality bright finished brass cup board locks or wardrobe locks with six levers including necessary screws etc. complete. (Indian make of approved quality) as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Prividing and fixing cement concrete chequred tiles 22mm (twenty milimeter) thick fixed on floor, Ramp on 12mm (tweleve milimeter) thick cement morter 1:3 (one cement isto three sand) jointed with neat cement slurry mixed with pigment to match the shade of tile as per PWD specification including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 300x300 mm (three hundred by three hundred milimeter) anti skid ceramic tiles 5.5mm (five point five milimeter) thick Jaiper series (premium quality) of Somany Nitico Kajaria bell tiles manufactured of approved shade and colour in flooring, for all floor including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 10mm (ten milimeter) thick anti skid water proof stain and impect resistent heavy duty double charge / ultra charge vetrified tiles 600x600mm (Six hundred by Six hundred millimeters) of Nitco / Rak/ Kajaria / Orient / Bell of approved shade and colour in flooring, laid over 12mm (tweleve milimeter) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying Precast terrazzo tiles size 300x300x25 mm (three hundred by three hundred by twenty five) millimeter hydraulic compressed and polished terrazo tiles ISI marked No. I.S. 1237 (50% white and 50% grey cement) in white, yellow, green and maroon chips of O and B size ( No. SG 403B) of NTC laid in floor, on a bed of 25 mm (twenty five milimeter) average thickness of cement motor 1:6 (one cement is to six sand) jointed with cement slurry mixed with pavement to match the shade of tiles including rubbing and polshing complete for all level complete as per approved specification , drawing, design The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying 25mm (twenty five) millimeer thick Kota stone single slab flooring in stair case over 20 mm (twenty milimeter) (average) thick base of cement mortor 1:4 (one cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing necessary and matching complete with round nosing including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying Kota stone 55 x 27.5 cm (fifty five into twenty seven point five) centimeter with 7.5 cm (seven point five) centimeter wide Jaisalmes yellow bend flooring over 20mm (twenty) millimeter average thickness based of cement mortar 1:4 (one cement four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing, moulding and nosing complete as per approved specifications drawing and design. includingentire carriage of material with all lead and lift and other incidental. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

50 mm (fifty milimeter) thick Cement concrete flooring 1:2:4 (one cement isto two sand isto four graded stone aggregate 20 mm (twenty milimeter) nominal size laid in one layer finished with a floating coat of neat Cement as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying 300x300x25mm(three hundred by three hundred by twenty five milimeter) labrador design rainbow series tiles flooring of N.T.C. of approved shade laid on a bed of 12mm thick cement mortar 1:3 (one cement isto three sand) for ramp as per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying vetrified tiles (300x300mmx8mm) (three hundred into three hundred into eight milimeter) of Kajaria / Swastik / Somany/Bell Tiles in grey/coloured of required shade in skirting up to all heights on 12mm thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying 200x300mm / 300x300mm (two hundred into three hundred / three hundred into three hundred) millimeter white glazed tiles 6 mm (Six milimeter) thick in skirting risers of steps and dado up to all heights of Kajaria / Swastik / Somany / Bell on 12 mm (tweleve milimeter) thick with cement mortar 1:3 (one cement isto three sand) and jointed with cement slurry with pigment to match the shade of tiles as required complete as per approved specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying 20 mm (twenty milimeter) thick polished boroda green marble slab with round noseing / moulding in flooring 20mm (twenty milimeter) thick base in cement mortar 1:3 (one cement isto three sand) including jointing with cement mortar 1:2(one white cement isto two marble dust) with an admixure of pigment to match the shade of the marble as per PWD specification including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing Uni stone 12.50 m (tweleve point five milimeter) cladding wall surface side as on face arch, masonary wall excetra on 12mm (tweleve milimeter) thick cement plaster 1:3 (one cement isto three sand) and jointed with cement slurry including scafolding ecxetra complete including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 0.60 mm (zero point sixty) millimeter thick prepainted steel sheeting of TATA / SAIL Jindal steel in roofing (ISI marked Z120) over steel trussed, pre painted galvanized steel and hot dip metallic zink coat sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron over 5 micron and back coating of polyster 5 micron over 5 micron primer coating including fixing necessary iron J or L hooks, bolt nuts 6mm (six) millimeter dia with prepainted limpat and rubber washers complete with all accessories as per approved speficiation drawing and design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 0.60mm (zero point six zero) millimeter pre-painted sheet ridge or hips 60cm (sixty centimetre) of TATA / Sail / Jindal steel roofing with hot dipped metalic zinc coat sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron over 5 micron and back coating of polyster 5 micron over 5 micron primer coating including fixing necessary iron J or L hooks, bolt nuts 6mm (six) millimeter dia with prepainted limpat and rubber washers complete with all accessories as per approved speficiation drawing and design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing pre-painted sheet valleys 90cm (ninety centimetre) over all of kotar metal single skin trapezoidal profiled sheet 0.60cm (zero point sixty centimetre) thickness sheet in roofing of TATA / Sail / Jindal steel roofing with hot dipped metalic zinc coat sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron over 5 micron and back coating of polyster 5 micron over 5 micron primer coating including fixing necessary iron J or L hooks, bolt nuts 6mm (six) millimeter dia with prepainted limpat and rubber washers complete with all accessories as per approved speficiation drawing and design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing plaing M.S. B.P. sheet 2.00 cm (two point zero) centimeter thick in evels board/ Facia / Sofit / Ceilling including cutting fixing jointing with /electric welding to steel roofs members and applying a coat of red lead primer complete as per PWD specification (frame work is to be measured paid for separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 300mm(three hundred milimeter) wide and 250mm (two hundred fifty millimeters) deep over all semicircular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design 0.63mm thick sheet including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing on wall face PVC (D-plast) rain water pipes of supreme / finolex / princ working pressure not less than 4.5 kg (four decimal five kilogram) per square centimeter including filling the joints with approved adhesive complete 150 mm (one hundred fifty milimeter) dia. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing on wall face PVC (D-plast) supreme / pinolex / princ of accessories for rain water pipes including filling the joints with approved adhesive complete 150mm (one hundred fifty milimeter) dia PVC plain bend. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete 150mm (one hundred fifty milimeter) dia plain shoes as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 150mm (one hundred fifty millimetre) diametre pipe MS holder bat clamps for 150 mm (one hundred fifty milimeter) PVC pipe of approved design to CI ,SCI or PVC pipes embeded in and including cement concrete blocks 10x10x10cm (ten into ten into ten centimetre) of 1:2:4 (one cement : two sand : four stone aggregate 20mm (twenty millimetre) nominal size) and cost of cutting holes and making good the wall etcetra including carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position in beams joists channels ,angles ,tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters, trusses and trussed purline and the like work including cutting hoisting fixing in position & applying a priming coat of red lead paint complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Painting two or more coats (excluding priming costs) on new steel and other metal surfaces with enamel paint of asian / nerolac to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete including carriage of material within all leads and lifts and other incidental as per approved specification, drawing, design and as directed by Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

6mm (six millimeter) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetewrs) in girth, in rough side with cement mortar 1:3 (one cement isto three sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetewrs) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

15mm (fifteen milimeter) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimeters) in girth, in fair side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

15mm (fifteen milimeter) thick cement plaster in single coat on brick/concrete /stone walls for exterior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimeters) in girth, in rough side with cement mortar 1:5 (one cement isto five sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying Doctor Fixit torch shiled (P-3160. 3mm (three milimeter)) shall be used for water proofing treatment on terraice, the depressed portion imeribronce are made for high grade bitumints and sealed polymix APP/SBS modified betumints in thick coded to non/worn polyster reinforcement to give core and puncher resistance. Application shall be done as per approved specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with Readymixed primer of approved brand complete as per PWD specification drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

White washing with lime on undecorated wall surfaces two coats to give an even shade including throughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter as per PWD specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) of nerolac susksho undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per PWD specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per PWD specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Distempering (two coats) with Dry distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Wall painting (two coats) with acrylic washable emulsion paint of asian paint / nerolac paint and manufacture on undecorated wall surfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface as per PWD specification, drawing and design including entire carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 50mm (fifty milimeter) CP pipe hand rail fixed with 35 mm (thirty five milimeter) dia CP pipe for stair case having baluster of size of 15/20mm (fifteen/ twenty milimeter) C.P. pipe and combination with 35mm dia (thirty five milimeter diameter) pipe CP pipe balaster welding at top along with hand rail and vertical blauste welding / jointed with each other with applying priming coat of red lead paint as per per PWD specification drawing and design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 50mm (fifty millimeter) MS hollow pipe hand railing on parapit in coridor as 19x19 mm (ninteenby ninteen milimeter) and 12x12 mm (tweleve by tweleve milimeter) cross hollow pipe with a clear height 40 cm @ 60 cm (forty centimeter at the rate of sixty milimeter) center to center jointed in cement concrete welded at top with hand rail M.S. Hollow pipe D-Section 40 mm (forty milimeter) over all vertical buluster welded with each other M.S. flat 40x6mm (forty by six milimeter) bottom and top with D Section hollow pipes included applying coat of red paint as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 50mm (fifty milimeter) dia M.S. Pipe hand rail slip resistent with round ends at to level at 75 & 90 cm (sevent five and ninty centimeter) height with 25mm (twenty five milimete) M.S. Pipe buluster welded to 50mm (fifty milimeter) dia pipe embeded in cement concrete 600mm (six hundred milimeter) center to center and should extended 30cm beyond the top and bottom of the ramp including welding with electrical and gas and framing a coat of approved shade as per direction of Engineer in charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing plinth protection 60mm (sixty milimeters) thick interlocking paver/cc paver block of NTC with 23cm dia (twenty three centimeter diameter) half round stoneware pipe for drainage porpose including over 1:5:10 (one cement isto five isto ten aggrigate) for beading of pipe as per PWD specification, The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing vitreous china water closet squatting pan (Indian Type W.C. Pan) big pan No 20090 of size 53x41mm (fifty three by forty one millimeter) with low lewel PVC dual flushing Cistren of CERA / Hindware / Jaguar (earth work, bed concrete, foot rest and trap to be measured and paid for separately) Orrissa Pattern including entire carriage of materials within all leads and lifts as per direction of Engineer-in-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing vitreous China wash down, water closet Angle Indian Universal closet (European type. W.C. pan) of CERA / Hindware / Jaguar of size 57x35x35x39cm (seventy five into thirty five in to thirty five into thirty nine centimeter) of star 5 No. 20087 with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately) as per PWD specification. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 100mm (One hundred millimeter) size ‘P’ or ‘S’ trap for water closet (squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 (one cement : one sand) sand cast iron including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing Solid Type plastic seat in white plastic seat and cover for wash down water closet with C.P. Brass hinges and rubber buffers complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 10.00 ltr. (ten liters) capasity PTMT Coloured / white low level duel flushing cistern of Hindware / CERA / Commondar / Diplomat with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately) as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing vitreous china wash basin of 550x400mm (five hundred fifty into four hundred milimetre) of delta No. 10010 of Hindware / CERA / Jaguar with double hole for pillar tap with C.I. or M.S. brackets painted white i/c cutting holes and making good the same including fitting (Flat back) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 32mm (Thirty two milimetres) diameters C.P. brass waste (Heavy duty make ISI marked) for wash basin or sink within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 32mm (Thirty two milimetres) nominal size diameters rubber plug for wash basin sink, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 32mm (Thirty two milimetres) nominal size diameters M.I. union for wash basin sink, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 100mm (hundred milimetres) nominal size diameters CP iron grating for nalhni trap, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 600mmx450mm (six hundred millimeter into four hundred fifty millimeter) bevelled edge mirror of Atul / Modi Guard /Goldenfish mounted on 6mm (six millimeter) thick A.C. Sheet or water proof sheet and fixed to plugs with C.P. screws and washers including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing C.P. Brass Towel rail of Kingstone / Jal / ESS size600mm x 20mmm (six hundred by twenty milimeter) complete with C.P. Brass brackets fixed to plugs with C.P. Brass screws complete within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 600 x 120mm (Six hundred into one hundred twenty milimetres) glass shelf with C.P. brass brackets and guard rail complete fixed to plugs with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing chromium plated brass soap dish of Kingstone / Jal/ ESS with C.P. brass brackets fixed to cleats with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 15mm (Fifteen milimetres) diameters C.P. brass bib tap with capstan head, of Kingstone / Jal / ESS, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 15mm (fifteen millimetre) Cansealed C.P. brass stop cocks with wheel of Kingston / Jal / ESS / Jaquar / Seilco including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing C.P. brass pillar tap with capstan head 15mm (fifteen millimetre) dia (Heavey duty makes of Kindston Gem / Parko / Jal / ESS / Jaguar / Sciko ISI marked No. 8931 & 8934) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 15 mm (fifteen milimetre) dia PVC connection pipe brass union 450mm (four hundred fifty milimetre) length including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 40mm (fourty milimeter) diameter steel pipe grab has fixed with wall and floor and fixed with toilet seat disable person including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing high pressure PVC spigot socket waste pipe ventilating pipe ISI marked of Pinolex / Repipe / Vactus including fixing with approved adhasive ectra complete for system of 150mm (onehundred fifty milimeter) diameter pipe with working pressure 4Kg / Cm2 including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC water storage tank of Sintex having 1000 Ltr capacity including G.I. (Galvanised Iron) inlet and outlet connection, 15mm (fifteen millimeter) bore ball value and mosquito proof PVC cover with locking arrangement including hosting up to all height above ground level including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing 15mm (fifteen millimetre) C.P. Brass full way valve with wheel including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing brass ball valve (horizontal plunger type) High pressure with polythene plastic floats including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing polythene aluminum polythene ( PE-AL-PE) composite pressure pipe of Kitec or its equivalent U.V. stabilized with carbon confirming to IS 15450-2004 for water supply including clamps at one meter spacing, cutting fixing and making good the wall etc. but excluding the cost of fitting internal work pipe exposed on wall 1216-16 mm (Sixteen milimetre) O.D. pipe complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying 20mm (Twenty millimeters) nominal bore/diameters to galvanized mild steel tubes (medium grade) of Jindal / TATA in tenches including all tube fittings such as nipples, elbows, unions, tees and clamps (earth work trenches paid for seperately) including within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying 15mm (Fifteen millimeters) nominal bore/diameters to galvanized mild steel tubes (medium grade) of Jindal / Tata in tenches including all tube fittings such as nipples, elbows, unions, tees and clamps (earth work trenches paid for seperately) including within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Excavation in drains and channels etc. in earth work in all classification of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturator soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimeter) layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge, within all leads, lifts of materials and other incidentals. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing gully trap grade"A" compete with C.I. gratting brick masonry chamber in cement moratr 1:5 (One cement isto five sand) and water tight C.I. cover with frame of 300x300 mm (Three hundred into three hundred millimetre) size ( inside) the weight of cover to be not less than 4.53 Kg (Four decimal five three kilograms) and frame to be not less than 2.72 kg (Two decimal seven two kilograms) square mouth traps 150mmx100mm (One hundred fifty into one hundred millimetre) size P or R Type complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and laying cement concrete 1:4:8 (One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm (Forty millimere) nominal size) in haunching of PVC pipes of the 150 mm (One hundred fifty millimetre) internal diameters including concrete for bedding necessary form work and curing complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes of Phenolex / Vectus/ Reliance 75mm dia (seventy five milimeter diameter) ISI marked including fixing with approved adhesive etc. complete. including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes 110 mm dia (One hundred ten milimeter diameter) ISI marked including fixing with approved adhesive etc. complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC single equal branch with oval access door, 75 mm dia (seventy five milimeter diameter) ISI marked insertion rubber washer 3 mm (three milimeter) thick bolts and nuts complete including fixing with approved adhesive etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC single equal branch with oval access door, 110 mm dia (one hundred ten milimeter diameter) ISI marked insertion rubber washer 3 mm (three milimeter) thick bolts and nuts complete including fixing with approved adhesive etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing composite end seal compression fittings equal tee 1216 as per IS-15450-2004 for cold water supply with jointing testing and fittings complete including cutting and making good the walls etc. including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing composite end seal compression fittings Female elbows 1216 X 15 mm (tweleve hundred sixteen by fifteen milimeter) thread as per IS-15450-2004 for cold water supply with jointing testing and fittings complete including cutting and making good the walls etc. including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing composite end seal compression fittings Male thread connector 1216 X 15 mm (tweleve hundred sixteen by fifteen milimeter) thread as per IS-15450-2004 for cold water supply with jointing testing and fittings complete including cutting and making good the walls etc. including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing composite end seal compression fittings female thread connector 1216 X 15 mm (tweleve hundred sixteen by fifteen milimeter) thread as per IS-15450-2004 for cold water supply with jointing testing and fittings complete including cutting and making good the walls etc. including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC clamps 75mm dia (seventy five milimeter diameter) ISI marked of approved design with steel screws and rawal plugs etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC clamps 110 mm dia (One hundred ten milimeter diameter) ISI marked of approved design with steel screws and rawal plugs etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing viterious pattern urinal of large No 60002 flat back type ( large) of size 39x37.5x59cm (thirty nine into thirty seven point five into fifty nine centimeter) of Hindware / Jaquar / Cera including connection the urinal waste pipe by means of white lead mixed with chopped hemp ( waste pipe to be measured and paid sepertely) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing vitreous china division plate for urinal 600x300mm (six hundred into three hundred millimetre) of Hindware / Jaquare / Cera complete in all respect including within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC floor trap of size 110 mm X 75 mm (one hundred ten by seventy five ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 200mm (Two hundred milimetres) thick walls of brick masonry using cement dust clery building brick in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Construction chamber 300mm x 300mmx500mm inside size for stop cock with C.I. surface bore 100mm x 100 mm x 75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 75mm thick foundation concrete 1:5:10 ( 1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete With 100 mm cast in situ plain cement concrete walls in 1:2:4 mix (1 cement:2 sand : 4 grades stone aggregate 20 mm nominal size complete with form work including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing veterious china matric Europian water closet of CERA / Hindware fixed with jet pressure for divying/disable person including all necessary fittings including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing veterious china matric wash basin of CERA / Hindware / Jaguar for divying/disable person make including all necessary fittings including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing stainless steel kitchen sink of diamond / AMC / UNIK standard ISI make 470 x 420 mm (four hundred seventy by four hundred twenty milimeter) with bowl depth178 mm (one hundred seventy eight milimeter) with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC double equal branch with oval access door, 75 mm dia (Seventy five milimeter) insertion rubber washer 3 mm (three milimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing PVC double equal branch with oval access door, 110 mm dia (One hundred ten milimeter) insertion rubber washer 3 mm (three milimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Constructing brick masonry chamber for under ground CI inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement : five sand) cover with frame (light duty) 355mm x 610mm internal dimensions total weight of cover with frame to be not less then 38Kg. (weight of cover 23Kg. and weight of frame 15Kg) RCC top slab with 1:2:4 (one cement : two sand : four graded stone aggregate 20mm nominal size) foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm nominal size) in side plaster 15mm thick with cement mortar 1:3 (one cement : three sand) finished smooth with floating coat of neat cement on wall and bed concrete etc. complete. Inside dimension 455x610x450mm deep single pipe line. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Brick bat filling under sock pit Complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Supplying cast iron cover without frame for manholes for frame of internal dimension 455mmx610mm (four hundred fifty five by six hundred ten milimeteer) rectangular C.I. Cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg (twenty three kilogramme) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

Providing and fixing of water lifting pump of 1.00 HP (horse power) of serex / kirloskar / Crompton / Wortington including all necessary fittings including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate inclusive royality malkana, toll texes, GST and other taxes imposed by the Govt.

PARAS SOOD