Construction of FRH Joharji , Dharampur Solan

Amount

Cutting in earth work in all kinds of soil such as plot and disposal for excavated earth in all leads and lifts through manually & mechanical means as per the direction of Engineer in-Charge and stacking of useful stones to specified dimension.

Disposal of surplus excavated earth by mechanical means upto a lead of 1 Km. on approved dumping site.

Excavation in foundations, trenches etc., in earth work, in all kinds of soil such as pick work, jumper work, blasting/chiseling/wedging out of soft/hard rock including pumping and bailing out water and stacking the excavated in specified manner clear from the edge of the excavation and then returning the stacked soil in 15 cm. layers, foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth in all leads and lifts as directed by the Engineer-in-Charge through manually and mechanical means, no additional amount will be paid in this account. a) side column pits b)C/L c) Porch

Providing and laying cement concrete 1:5:10 (1cement:5sand:10grades stone aggregate 40mm nominal size) and curing complete excluding cost of form work in retaining wall/breast wall, with 15% plum and curing complete as per HP PWD specification including carriage of materials in all leads and lifts. a) side column b) C/L c) Porch d) under florings

Providing and laying boulder soiling under floor at ground level.

Providing and laying cement concrete 1:2:4 (1cement:2sand:4graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work including carriage of materials in all lead and lifts.

Providing and laying cement concrete 1:1.5:3 (1cement:1.5sand:3graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work mixed with mechanical mixture and vibrator and curing complete including carriage of materials in all leads, lifts and upto all height. A) Foundation, footings, basis of columns and mass concrete. Pedastals Wall any thickness but not less than 0.10 mt. thickness

Suspended floors roofs, landings, shelves and their supports, balconies, beams, girders, bressumers and cantilevers. A) less staircase b) Plinth, Ground & First Floor beams C) Lintel Beams d) Poarch Plinth Beams

Columns, pillars, posts and struts

Staircase (except spiral stair cases) excluding landing but including preparing of the surfaces and finishing of nosing.

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including cemering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in site reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. 1)Beams, cantilever, girders and lintel:- Side of soffits of beam, beams hunching cantilevers bressumbers and not exceeding 1 meter in depth in all heights. Plinth, Ground & First Floor Beams a0Lintel Beams b0 Poarch , Plinth beams

Foundation, footings, basis of columns and mass concrete.

Flat surfaces such as soffits and suspended floor, roofs landing and like plain upto 200 mm in thickness.

Columns, pillars, posts and struts square, rectangular in plan. Pedastals Columns, pillars, circular in plan.

Stair case with sloping stepped soffits including landing.

Vertical surface such as walls (any thickness) partitions and the like including attached pilasters, buttresses, plinth and string course of the like.

Providing mild steel/tor steel reinforcement for RCC work including bending, binding also cost of binding wire and placing in position complete upto all floor level including carriage of materials in all lead and lifts. 1) Tor steel

Brick work 2nd class using common burnt clay building bricks in Foundations below plinth level in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads and lifts. A) less doors b) Less windows c) Less ventilators

Brick work 2nd class using common burnt clay building bricks in Super-structure above plinth level in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads and lifts.

Half brick masonry in common burnt clay building bricks 2nd class in superstructure upto all heights in cement mortar 1:4 (1cement:4sand) including carriage of materials in all leads and lifts. A) Less doors b) Less ventilators

Brick work exposed class using moduler common burnt clay building bricks moulder bricks in super structure above plinths level in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads and lifts of pioneer make (from Barwdo).

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position in Sal wood including carriage of materials in all lead and lifts.

Providing wood work in trusses, purlins, rafters, posts, post plates, wall plates and the like wrought framed, hoisted and fixed in position including carriage of materials in all leads and lifts and heights. 1)IInd Class Deodar wood.

Providing and fixing paneled glazed or paneled and glazed shutters for doors windows and clerestory windows including black enameled iron butt hinges with necessary screws including carriage of materials in all leads and lifts. 40 mm thick Ist Class Deodar wood a) Windows b) Ventilators

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56 mm for doors, windows and clerestory enameled iron hinges with necessary screws including carriage of materials in all leads and lifts. 40 mm thick II nd Class Deodar wood Providing and fixing plain lining with tongue & groved jointing and screws (frame work & cover fillets to be measeured & paid for separately with) including carriage of materials within all leads and lifts. 12 mm thick 2nd class Kail wood.

Providing and fixing 75x60 mm rounded hand rail in straight length complete in 1st class teak wood complete including carriage of materials in all lead and lifts.

Providing and fixing convex type aesthic deodar wooden piece alongwith bracket etc. complete as per detailed architectural drawing including carriage of materials in all leads and lifts.

Providing and fixing ornamental type deodar wooden pieces of standard size and section complete as per detailed architectural drawings including carriage of material in all lead and lifts.

Providing and fixing bright finished brass sliding door bolts with nuts and screws etc. complete including carriage of materials in all leads and lifts of flora make. 1) 300x16 mm

Providing and fixing bright finished brass tower bolts (barrel type with nuts and screws etc. complete including carriage of materials in all leads and lifts of flora make). 1) 200 mm x 10 mm

150 mm x 10 mm

100 mm x 10 mm

Providing and fixing bright finished brass handle with screws etc. complete including carriage of materials in all leads and lifts of flora make.300 mm size ornamental

Providing and fixing M.S. double acting spring hinges bright finished with necessary screws 15 mm including carriage of material in all leads and lifts.

Providing and fixing bright finished hard drawn hoos & eyes 200 mm.

Providing and fixing 40x3 mm flat iron hold fast 40 Cm. long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 (1cement:3sand:6graded stone aggregate of 20 mm nominal size).

Providing and fixing door closer of everest make including fixing with necessary nails and screws including carriage of material in all leads and lifts.

Providing and fixing Nitco/Equivalant vitrified tiles 8 mm to 10 mm thick any series of size 600 mm x 600 mm in flooring, laid on a bed 12 mm thick cement mortar 1:3 joining with cement mixed with pigment to match the shade of tiles including carriage of materials in all leads and lifts and heights. Tiles basic price 60/- per sq.ft. a)Skirting b)1st floor slab c) Skirting

White/Coloured printed glazed tiles in skirting, risers of steps and dado of size 450x300 mm size laid over 12 mm thick cement mortar 1:3 (1cement:3sand) and jointed with cement slurry including carriage of materials in all lead and lifts and heights of Nitco make series.

25 mm thick kota stone slab in flooring laid on 20 mm (average) thick cement mortar 1:4 (1cement:4sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete including carriage of materials in all lead and lifts and heights.

Providing and laying granite stone flooring 20 mm average thickness over a base of 20 mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with grey cement slurry mixed with pigment to match shade of the granite stone including rubbing polishing with granite polishing finish gray/red including edge moulding where required. a) Washrooms b) Kitchen

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet of approved quality fixed with bolt and nuts complete as per direction of the Engineer/Architect of tata company.

Providing and fixing ridges or hips 60 cm over all in plain galvanized iron prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet fixed with J or L hooks bolts and nuts 8 mm dia GI limpet and bitumen washer complete 0.60 mm thick sheet including carriage of materials in all leads and lifts and heights.

Providing valleys 90 cm. overall in plain prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet fixed with galvanized iron J or L hooks bolts, nuts 8 mm dia, GI limpet and bitumen washer complete including carriage of materials in all lead and lifts.

Providing flashing 38 cm overall in plain prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet fixed with galvanized iron J or L hooks, bolts and nuts, GI limpet washer and bitumen washers complete, bent to shape and fixed in walls with cement mortar 1:3 (1cement:3sand) 0.60 mm thick sheet including carriage of materials in all leads and lifts and heights.

Providing and fixing 15 cm wide 45 cm overall semicircular plain prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet gutter with iron brackets 40x3 mm size bolts and nuts and washer etc. including making necessary connection with rain water pipe complete as per design 0.60 mm thick including carriage of materials in all lead and lifts.

Providing and fixing on wall face C.I. rain water pipes including fitting the joints with spun yarn and cement mortar 1:2 (1cement:2sand) 100 mm dia pipe ISI make of heavy duty including carriage of materials in all lead & lifts.

Providing and fixing wall face C.I. accessories for rain water pipes including fitting the joints with spun yarn soaked in neat cement slurry and cement mortar 1:2 (1cement:2sand) including carriage of materials in all lead & liftsC.I. plain bend 100 mm ISI make heavy duty

C.I. plain Shoe 100 mm ISI make heavy duty

Steel work welded in built up section, trusses and framed work, including cutting, hoisting, fixing in position and applying a coat of red lead paint including carriage of materials in all lead lifts and heights.In gratings framed guard bars ladders, railings brackets and similar works.

In beams, joists channels, angles, tees, flats with connection plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like etc.

Providing and fixing 2 mm thick B.P. sheet eaves board/facia/ceiling over angle iron frame with applying a coat of primer etc. (frame work to be measured and paid separate).

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand, papering and knotting including carriage of materials in all lead and lifts (Nerolac of Asian).a) Ready mixed paint other than white.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with readymixed paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping (Nerolac or Asian).Ready mixed paint other than white

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter (Nerolac or Asian).White/other than white enamel paint.

Polishing two or more coat with lacquer polish on new wood and wood sealer/lacker including preparing the surface complete as per the direction of the Engineer-in-Charge).

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease, dirt and other foreign matter and scoured with wire brushes fine steel wood scrapers and sand paper complete.With ready mixed priming paint brushing red lead, red, oxide/zinc oxide chrome including carriage of materials in all lead and lifts and heights.

6 mm thick cement plaster to ceiling in cement mortar 1:3 (1cement:3sand) including carriage of materials in all leads and lifts and heights.

15 mm cement plaster in single coat on rough/ fair side of brick/concrete/stone wall for interior plastering in all floor level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads, lifts and heights.

Wall painting ( two coats ) with plastic emulsion paint of approved brand and manufacture on decorated wall surface to give an even shade including thoroughly brushing the surface clean of all dirt grease loose pieces of scale and sand papered smooth including applying of putty a required for making the surface including carriage of materials in all lead and lifts (Nerolac/Asian).

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required with ready mix premier including carriage of materials in all lead and lifts and heights. (Nerolac/Asian)

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including carriage of materials in all leads lift and height. (snocem/Kiposum

Applying putty (Birla/J.K.) on undecorated wall including preparing the surface by thoroughly cleaning grease, dirt dust and other foreign matter including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75 mm thick consolidated (bed dry brick/stone aggregate 40 mm nominal) well rammed and consolidated and grouted with fine sane including preparation of ground including carriage of materials in all lead and lifts.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement:3sand:6 aggregated 20 mm nominal size) including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall 15x22 cm in cemenet 1:6 (1cement:6sand) and inside plastering with cement plaster 1:3 (1cement:3sand) including earth work and laying 10 cm cement concrete 1:5:10 (1cement:5sand:10 stone aggregated 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1cement:2sand:4 aggregated 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts

Supplying and fixing glass panes fixed with deodar wood beading including carriage of materials in all leads and lifts.5.5 mm thick plate glass Atul/Modiguard.

Providing and fixing moulding of required size around doors of windows to cover the joints of frame of 1st class teak wood including carriage of material in all leads and lifts size 40x12 mm.

Stone work ashlar punched (ordinary work) in superstructure upto floor two level in cement mortar 1:6 (1 cement : 6 sand) including pointing with cement mortar 1:2 (1 cement : 2 sand) in square & rectangular pillars.

Sanjay Kumar