SPECIAL REPAIR TO BLDG NO P-4 OF 371 FD HOSP UNDER GE MISAMARI

Amount

Demolition Cement Concrete not exc 15 cm thick above or below the groung level complete .

Demolition Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for, complete .

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, rubbish off the premises etc

Demoliltion of brick work built in cement mortar including PCC coping complete all as specified and directed.

Taking down Chowkat or Frame (without taking off shutter from the frame) not exc. 1.50 Sqm Each, complete .

Taking down Chowkat or Frame (without taking off shutter from the frame) exc. 1.50 Sqm but not exc 4.00 Sqm Each, complete .

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete .

Taking down Cement Plaster of any description on brick walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, remove dust, debries/rubbish etc., complete .

M&L Brick Work with Sub-Class ‘B’ Bricks (with Old Size Bricks) half brick thick, Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick work with sub class B brick straight or curved on plan exc 6.00 m mean radious built in CM 1:6 complete all as specified.

M&L for Rendering 15mm thick in cement mortar 1:6 on fair faces of Brick walls or on concrete surfaces, finished fair and even, complete .

M&L for 15mm thick rendering in Cement Mortar 1:4 on Fair Faces of Brick Walls or on Concrete Surfaces plastered Surfaces Finished fair and even, complete

M&L for Rendering 5mm thick in Cement Mortar 1:3 on Concrete Surfaces of Ceiling, etc., plastered surfaces finished Even and Smooth, without using Extra Cement, complete .

Dismantling floor hearth or wall tiling incl cement mortar bedding but not backing and removing rubbish off the premises complete all as specified as specified and directed

M & L for non-skid mat finish ceramic colour tiles 300x300, 7 to 8mm thick in floors etc. set and jointed in neat cement slurry and pointed with white or coloured to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete .

M & L for glazed ceramic colour tiles 600x300, 7 to 8mm thick on vertical surfaces of wall such as dados, skirtings etc set and jointed in neat cement slurry and pointed in white cement to match with tiles over and incld.10mm thick screed plaster in CM 1:4, complete .

M & L for non-skid mat finish ceramic colour tiles 600x600, 7 to 8mm thick, in floors etc. set and jointed in neat cement slurry and pointed with white or coloured to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete .

M & L for glazed ceramic colour tiles 600x150, 7 to 8 mm thick on vertical surfaces of wall such as skirtings etc set and jointed in neat cement slurry and pointed in white cement to match with tiles over and incld.10mm thick screed plaster in CM 1:4, complete .

M&L Granite (of any type) 18mm thick, work (table rubbed and polished) in cooking platform, sheleves and like in cement mortar (1 : 4) including pointing in white cement( 1 : 2) using marble dust with admixture of pigment to match with shade of granite complete .

M & L for preparation of newly plastered surface of wall and apply two coats of oil bound distemper over a coat of 1mm average thick wall putty, all as specified & directed.

M&L for complete removal of existing treatment of old plastered surface of wall and applying two coat of Acrylic washable distemper over a coat of 1mm average thick wall putty white cement base (J K & Birla) and making smooth finish, complete all as specified & directed.

M&L for prepartion of new plastered surface of wall and applying two Exterior weather proof paint over a coat of alkali resistant primer over a coat of wall care putty 1mm thick,, complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered surface of wall and applying two coats Exterior weather proof paint over a coat of wall care putty 1mm thick, complete all as specified and directed.

M & L for preparation of old plastered Surfaces of ceiling and applying one Coats of White Wash complete .

M&L preparing newly Plastered Surfaces of Ceiling and applying Three Coats of White Wash, complete .

S&F Pressed steel frames for doors with double rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified of size 125x60mm complete all as spd.

S&F Pressed steel frames for doors with one rebate including necessary fixing lugs, hinges, lock strike plate etc complete as specified of size 105x60mm complete all as spd.

M&L for cement concrete 1:2:4, Type-B-0 (12.5mm graded stone aggrgate) as in filling in steel frome/roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed.

S&F flush shutters, 30mm thick, solid core construction with block board core & ply wood face panels, commercial type on both side incl 30X 6mm thick 2nd class HW lipping on edge, complete all as spd & directed.

S & F IInd Class HW 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) supplied and fitted to chowkats, complete .

S & F solid PVC door frame of size 100mm x 45mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match with printed sheet as reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed.

S & F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), design with 2mm thick 3D wood grain moulded PVC sheet painted on the front face & 2mm thick plain colour PVC sheet on back face complete all as directed.

M&L for Powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium Frame for Doors, windows, ventilators with one or more rebates, aluminium grill and U clips, including jointing cleat for fixing etc, complete all as specified and directed.

M&L for Powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S&F S&F mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars, railings and similar work complete conforming to Fe-410-0 or Fe-310-0 complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete by the Engineer-in-Charge.

S&F sheet glass, ordinary quality 3mm thick fixed with oil putty size of glass not exc 0.50 sqm in each pane complete .

S & F figured glass pin headed type, 3 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane complete .

S & F in repair 25mm dia, Harrison rails, anodised aluminium alloy powder coated with fixing brackets, stops, etc. , tubular curtain rail fancy type complete .

S&F for 150mm long aluminium, anodized, barrel tower bolts of extruded section complete .

S & F 150mm aluminium handles, cast type, anodised complete by the Engineer-in-Charge.

S&F for 100mm size stainless steel butt hinges complete all as specified and as directed.

S&F for 300mm mild steel ordinary rat tail pattern springs incl roller plate complete as specified.

S&F Mild steel sliding door bolts 300mm,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F floor door stopper of aluminium alloy body & tongue of size140mm, anodised with hard drawn spring,fixed in door, complete .

M & L prepration of new wooden surfaces and applying two coats of synthetic enamel paint over coat of pink primer on newly wooden surfaces of any description not otherwise described over 10 Cm width or girth complete.

M&L for prepration of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified, complete.

M&L 15mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors incl taking up or down steel tubing 15mm bore complete all as specified & directed

M&L 20mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors incl taking up or down steel tubing 20mm bore complete all as directed.

S&F in repair 15mm bore fancy type CP brass one way or two way Bib Cock (Foam Flow) with Flange (as approved) complete all as specifed and directed.

S&F in repair CP brass 15mm bore Single Lever Basin Mixer without popup waste swan neck Braided Hoses (as approved) complete all as specifed and directed.

S&F in repair CP 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed (as approved) complete as directed.

S&F in repair CP 15mm bore 2 way angular stop Cock with Wall Flange of suitable for fixing to GI Pipe complete all as specifed and directed.

S&F in repair CP brass 15mm bore Wall Mixer 3-in-1 with provision for both Over Head Shower with Hand Shower with 115mm long bend Pipe (as approved) complete all as specifed and directed.

S&F in repair CP 15mm bore Sink Cock with Swivel Casted Spout (Wall mounted) (as approved) complete all as specifed and directed.

S&F in repair Chromium plated shower roses with swivel joints, 150x150mm with CP arms 300mm long, including fixing to steel pipe or union complete all as specifed.

S & F in repair tubular towel rail , chromium plated brass 20mm dia ‘D’ type 60 cm long between flanges complete .

S & F in repair 15mm bore CP body health faucet with 1 mtr long easy flex tube in chrom finish & wall hook (as approved) complete all as specifed and directed.

S & F in repair PVC connection, heavy duty 15 mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality complete .

S & F in repair PVC waste pipe of 32 mm bore of adequate length complete

S&F in repair, Sheet Glass shelf (corner) Assembly, consisting of 5.5mm thick Glass Shelf 3 tier with Guard and Railing complete all as specified.

S&F in repair, Sheet Glass Shelf Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete .

S&F in repair CP brass Soap Dish holder (as approved) complete all as specifed and directed.

S&F in repair Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Plastic seat cover, Trap and Fixing Bolts (excluding Flushing Cistern and Flush Pipe) including connection to drain (or outgoing pipe) and to Flushing Pipe and Making Good to Floor/distrubed surfaces complete all as specified and directed.

S&F in repairs PVC Flushing Cistern 10 LITRE capacity White, Low Level, Valve less, syphonic action type with Inlet, Ball Valve, Float and handle, complete.

S&F in repairs Vitreous China Wash Hand Basin of size 550x400mm (Flat Back or Angle Back type) with pedestal including 32mm bore (dia) Brass CP Waste Fitting and fixing brackets, complete.

S&F in repair, Stainless Steel Sink with Drainage Board l.0mm thick Over-all size 915x460mm and Bowl size 410x330x160mm for Kitchen with and incl fixing brackets (if required) or bedding in CM of any description, complete .

S & F in repair rotational moulded polythylene, triple layer water storage tank 500 litre capacity (cylinderical vertical with closed top,) hoisted & fixed in position all as specified in SSR Part-I including dismantling existing water storage tank and removal from site complete.

S&F CP brass Grating Doom 100mm dia (minimum weight 40 Grams) and fixed-in-repairs, complete .

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Singe Socketed, in any length with Rubber Ring Joints with and including all fittings like bend, tee, floor/gully trap. or junction etc fixed to Walls or laid in floors complete all as directed.

S&F in repairs PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Singe Socketed, in any length with Rubber Ring Joints with and including all fittings like bend, tee, floor/gully trap. or junction etc fixed to Walls or laid in floors, complete all as directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

M & L 75mm thick PCC 1:3:6 Type C2 using 40mm graded aggregate as in plinth protection/path finishing even and smooth with using extra cement incl demolition of existing damaged cement conctete complete .

M & L 100mm thick PCC 1:3:6 Type C2 using 40mm graded aggregate as in sub base complete all as specified.

M & L DURASTONE Heavy duty tiles of size 300x300x10 mm thick laid over 15 mm thick screed bed in CM 1:6 as footpath set and jointed in neat cement slurry and pointed in grey cement complete all as specified

S & F mild seel deformed bar 10mm dia over cut to length bent to shape requiired including cranking bending and binding with and including mild steel wire annealed not less than 0.9mm dia.

S&F in repair 18/19mm thick pre-laminated PVC board, both side with decorative choice lamination as in kitchen cabinets and cupboards complete.

S&F Mild steel rollers and plate suitable for sliding drawers, complete .

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised., width of flaps when open in 30mm complete .

S&F for Mortice lock, vertical type, size 65mm, 4 lever Brass body, complete .

S & F 75mm brass handles, cast type, polished bright, fixed with brass screw, complete .

S&F in repair, PVC Cabinet of size 450x350x90mm with Looking Mirror (as approved) fixing with Chromium plated Brass Screws and Wooden/Plastic Cleats, complete as all specified and as directed.

S&F of Structural steel, rolled section as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde-E-250)all as specified and directed by Engineer-in-Charge

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (ii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iii) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (iv) Applying two coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick Flat, rough finished surface complete .

M & L RCC 1:2:4 type B-1,(using 20mm graded crushed stone aggregate) as in slab supported on walls, beam and column in floors , roofs, landing deck slab etc with and incl used and waster of formwork whereever reqd complete.

M & L for PCC 1:4:8 type D-2 using 40mm graded aggregate as in foundation filling and mass concrete all as specified

Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out in soft/lose soil returning, filling in and ramming earth in layers n.exc 25cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specifed and directed.

M & L for PCC 1:2:4 type B-2 using 40mm graded aggregate as in foundation filling and mass concrete all as specified

Taking down carefully existing unserviceable copper/ aluminium point wiring (light,call bell, two way, socket or power point etc) complete with fittings/fixures such as switches sockets, ceiling rose, fan regulators,bracket light fittings and making good to the disturbed surface complete all as directed by Engr-in-Charge.

Taking down the existing unservicable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified by Engr-in- Charge.

Taking down carefully unsv aluminium submain wiring of any type /loc including conduit /casing and earth wire and making good the distributed surface of walls /ceiling matching with existing finishes all as directed by Engr-in-Charge.

Taking out unsv UG Cable any cross sectional area and connection of any description of any description laying in trenches or fixing with wall or poles all as specified and directed.

M & L for Point wiring with 1.5 Sq mm copper conductor single core FRLSH PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC Concealed conduit and its accessories of suitable size, high grade ISI marked in walls /roof and PVC boxes of suitable size including fixing/grouting sunken/ surface as per site requirement for mounting the switches / sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLSH PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified forOne light point controlled by one, one way switch 5 Amps

-Ditto- all as per item No. 97 but specified for One ceiling fan / exhaust fan point controlled by one , one way switch and regulator

-Ditto- all as per item No. 97 but specified for One 3 point 5 Amps socket outlets point controlled by one switch on the same board

-Ditto- all as per item No. 97 but specified for One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

-Ditto- all as per item No. 97 but specified for One call bell point controlled by one bell push

Description all as per item No 97 here in before but for one light point controlled by one, two way switch 5 Amps

All as per item No 97 above but with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board.

S & F Switch piano flush type single pole one way 5 Amp, 230 Volts complete all as specified.

S & F Modular switch piano single pole flush type, two way, 6 amps, 230 volts.complete all as specified and directed.

S & F Socket outlet 2 in 1, 3 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination flush type multipurpose 2/3 pin 5 Amps two in one , 230 volts complete all as specified

S&F Switch socket combination 2 in 1 3 pin, 15 Amp flush type universal.

S&F ceilling rose three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all specified

S&F bell push,5 Amp, flush type

S&F Buzzer, Ding Dong AC. 230 volts, single pole

S & F ceiling fan regulator step type, flush type heavy duty suitable to work on 230 Volt AC supply complete all as specified.

S & F Lamp holder with insulated body, with back plate suitable for batten fittings complete all as directed.

S&F Decorative wall light fixture made up of polycarbonate suitable for 10W LED Lamp complete all as specified.Make- Philips , Model - Comet Wall Light 30575 and equivalent in Havells and Surya.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.Make-Make- Havells, Cat No: LHLDEUEBML8Z010 or equivalent in CG or Surya.

S & F sheet metal enclosure MCB VTPN 8 way Double door Ready to use DBs - Provided with insulated vertical phase bus-bars |neutral bar/s with shroud/s | earth bar/s | sticking saddles | cement spill protector | color-coded interconnecting wire set | cable ties | blanking plates and circuit identification labels With provision for 4 Pole MCCB 125 A as incomer and SP/SPN MCBs as outgoing complete all as specified and directed.Make- L&T, Cat No: DBVTH008DD and equivalent in Legrand and Indo Asian.

S & F MCCB 4 Pole 415 volts 125 Amps with thermal - magnetic release with breaking capacity 36 KA and with adjustable overload setting complete all as specified. Type- DN2-250D Model:-CM92108OOL1OG, Make:- L&T and equivalent in Legrand and Indo Asian.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified. Make:- L&T, Model -DBSPN006D and equivalent in Legrand and Indo Asian.

S & F MCB Double Pole 32 Amps 240/415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, C-curve, complete all as specified and directed.Make- L&T, Cat No: BB20320C or equivalent in Schinder/ Legrand.

S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, C-curve, complete all as specified and directed. Make -L&T,Model No-BB10060C,BB10100C,BB10160C and equivalent in Schinder/ Legrand.

S & F wall mounted LED 18 watts ,Batten type T 8 light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including Ultra bright LED polycarbonate (T8) tube (Single side connection) 4' x 18 watts with G13 lamp holder complete all as directed by Engineer-in-Charge.Model -REGALBATTENT8UPTO1X18WDSBSWH For Batten Fitting and Model-PHOTONULTRAE2.01213T8SSTL18WLED865SPC For T8 Tubelight ,Make Havells, or equivalent in CG, Surya, all as specifed and directed.

S & F wall mounted LED 10 watts ,Batten type T 5 Mirror light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting ,Make Havells, or equivalent in CG, Surya, all as specifed and directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 15 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as directed by Engineer-in-Charge. Make- Havells,Model No - ENDURAPEARLSL15WLED757SASYTOPCMP Or Equivalent in CG and Surya all as specified and directed.

Excavation in trenches n exc 1.50 m wide and n exc 1.50 m depth in soft /loose soil and getting out for lying of cable and errection pipe etc complete all as directed.

Returning, filling in, trenches in soft /loose soil including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as directed.

Removal of excavated soil to a distance n. exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as directed.

M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation 08 cm thick before laying of cable & 15cm thick after laying of cable & punning complete all as directed. (Note : only punned thickness of 18cm shall be measured & paid)

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified.

Supply & Laying LT heavy duty UG Cable of size 50 Sqmm 3.5 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed. Make :- Polycab and equivalent in Havells and KEI

S & F GI Tubing light grade of size 50mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc all as specified and directed.

S&F Bulk head in die cast aluminium housing & frosted glass suitable for 1 x 8W LED complete all as specified. Model - RUGBY, LHKL01160099 , Make:- Havells and equivalent in Surya and CG.

Taking down ceiling fan/ Exhaust Fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv core PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

M&L for replacement Sub main wiring 2 x 6 Sqmm multi-strand FRLSH PVC insulated copper conductor unsheathed cable including concealed conduit and continuous earth wire of FRLSH PVC insulated multi-strand copper conductor of size 6.0 sqmm complete all as specified and directed. Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles.

Supply and fixing for single pole and neutral enclosure with a two pin and earth plug and socket complete with on one single pole MCB 20 Amp, 240 volts.Make:- L&T/Havells/Legrand

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I.

bkgeneralstores

Sunrise Enterprise

Markson