Construction of new toilet in Bhavani 6th floor in Technopark Phase-I Campus Trivandrum

Amount

Toilet work

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Hollow block masonry using pre cast blocks ( Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Hollow block masonry using pre cast solid blocks ( Factory made ) of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for Super structure above floor two level upto floor five level for 10cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand ) including cost of scaffolding etc complete The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All floors & All levels: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Plastering with cement mortar 1:6(1 cement & 6 sand) 12mm thick one coat floated hard and trowelled smooth for inside and outside walls including cost and conveyance of all materials to site, labour charges, hire charges for scaffolding, watering for curing, etc. complete for all floors for all heights as per the direction of engineer in charge. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Steel work in built up tubular G.I (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing precoated galvanised steel sheet roofing accessories TATA 0.45 mm thick Tile profile roof sheet (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete: Ridges & Vally Gutters with plain (500-600 mm) The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Dadoing the walls with best quality glazed tiles / vitrified tiles (colour to be approved by Technopark ) / 600 x 600mm or nearest size 1st class tiles ( RAK/KAJARIA /ASIAN), to be approved by the Technopark, fixing the tiles after applying a coat of cement mortar 1:3 , 9mm thick with a neat flushing coat / MYK latricate with cement grout and fixing the tiles to correct lines and plumb with paper tight joint and pointing with white cement / matching pigment etc. with cost and conveyance of all materials to site, labour charges etc. complete for all floors as per the direction of engineer in charge. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Centering and shuttering including strutting, etc. and removal of form for: Lintels, beams, plinth beams, girders bressumers and cantilevers The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of whicj 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95 mm wide PVC sheet out of which75 mm shall be tapered in 45 degree on th inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mmx2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded /sealed to the styles & rails with 7 mm (5 mm + 2 mm ) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer -in-charge, manufacture's specification & drawing. 30 mm thick plain PVC door shutters The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of surface as required for treatment of roofs, balconies, terraces, toilets etc, cement admixed with water proofing compound (provide minimum 3 coats ( top coat polimer based coating) of approved water proofing compounds) approved by engineer-in-charge and technical specifications for any floors. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/ sqm by the same membrane manufactured of density at 250C, 0.87-0.89 kg /litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : joint strength in longitudinal and transverse direction at 230C as 350/ 300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 1500C. Cold fexibility shall be upto -20C when tested in accordance with ASTM. D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2 The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2 The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 6Kgf/cm2 The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2 The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia BendThe rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: One urinal basin with 5 litre white P.V.C. automatic flushing cistern The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brasspillar taps The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing SS. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-Charge. Anodized (AC 15 ) aluminium The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing ISI marked oxidised Aluminium tower bolt black finish, (Barrel type) with necessary screws etc. complete: 150x10 mm The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge. Pre- laminated particle board with decorative lamination on both sides The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 15 mm nominal bore The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC.waste fittings complete. Flexible pipe 32 mm dia The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 150 mm dia floor trap The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

Providing and fixing toilet paper holder: C.P. brass The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space etc complete as per the direction of engineer in charge.

R U CONSTRUCTIONS

VIJAYAN K