Re-tender for the Renovation Work at KINFRA

Solid block masonry in CM 1:5 (1 cement, 5 coarse sand) including cost of all materials, labour, curing etc. complete. For wash area

Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturers specifications in superstructure above plinth level up to floor V level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2

Honey-comb brick work 10/11.4 cm thick with common burnt clay bricks of class designation 7.5 in super structure with cement mortar 1:4 (1 cement : 4 coarse sand).

Plastering walls - Providing and applying minimum 12mm thick single coat cement sand plaster in cement mortar of mix in ratio of 1:4 (1 cement : 4 sand) floated hard and trowelled smooth / rough finish to receive specified finish, including providing chicken mesh at joints of concrete and masonry and for all service lines including cost of all materials, labour, scaffolding, curing, etc complete.

Roof top plastering -12 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement.-for open terraces and leaking sunshades

Water proofing above porch,sunshades etc using 2 coat water proofing chemical over roof (Pidilite or equivalent)

Al powder coated door with glass and laminated board infill: Providing and fixing aluminium work for doors with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming toIS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up thegaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing shutters of doors, including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required . Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-Charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

providing and fixing Hard ware items forAluminium doors including mortice lock, floor spring with stainless steel plate,powder coated Aluminium tubular handle bar,tower bolts etc

Filling the gap in between aluminium frame & adjacent RCC / Brick / Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineerin-Charge complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door including frames shutters and all fixtures for toilets

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand),including pointing the joints with white cement and matching pigment etc., complete.

Ceramic tile acid washing and cleaning for toilet and wash area

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours,of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(tile cost Rs. 300/m2)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc

Distempering with oil bound washable distemper of approved brand and manufacture to give an evenshade: for Old work (one or more coats) including . complete if necessary-(internal walls)

windows

Doors

300 nos small table( 750H*500B*500W)

Varnishing with varnish of approved brand and manufacture: One or more coats with copal varnish -varnishing of 300 nos wooden cot( 1900L*700B)

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Removing white or colour wash by scrapping and sand papering and preparing the surface smoothincluding necessary repairs to scratches etc.

White washing with lime to give an even shade: over Old work (two or more coats)including complete for ceiling

Providing and fixing Gypsteel pre coated (Exposed portion only) GI T Grid system in 600x600mm module which includes necessary fixing arrangements .gypsum tiles of size 595x595mm shall be placed into the grid size of 600x600mm.

Mosquito net for windows using HDPE net and powder coated Aluminium sections

Dismantling doors, windows shutter including chowkhats,architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls,flooring and jambs complete, to match existing surface i/c disposal of mulba / rubbish to the nearest municipal dumping ground.

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm, with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead: Door chowkhats

Window chowkhats

Reinforced cement concrete workfor slabs up to floor five level excluding cost of centering, shuttering, finishing and reinforcement :(for external wash)

Centering and shuttering including strutting, propping etc. and removal of form for :slab

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level

Floor Cleaning- Engaging labours for cleaning and other miscellaneous works at site

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1 cement : 4 fine sand)

Providing and Fixing mirror polished granite of approved colour,texture and size of 18mm thick laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.over panrty platform side

Providing and fixing M.S. grills of required pattern. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings/ wooden frames with rawl plugs screws etc for toilet ventilators using 8mm rods

Flooring maintenance -Cement flooring on passages

Plastic chair for Rooms

Plastic chairs for Dining

Dining table - using carved teak wood legs and laminated particle board topping (150 cmx 90 cm)

MCB Distribution BoardsSupply, Erection, testing and commissioning of Indoor , wall mounting double metal door type[IP 43] MCB Distribution Boards consists the following with complete wiring, including cable termination, connection, earthing, circuit identification numbering, DB numbering, DB dressing using cable ties etc. complete as required.

12 Way TPN MCB DB

Incomer: 63A, 4 Pole, MCB - 1No.

Outgoing: 40A, 2 Pole, 30 mA ELCB, C curve - 3 Nos

6/16/20A 10KA SP MCB, C curve - 21 Nos

8 Way TPN MCB DB

Incomer: 40A, 4 Pole, MCB - 1No.

Outgoings: 40A, 4 Pole, 30 mA ELCB - 2 Nos

6/16/20A 10KA SP MCB, C curve - 12 Nos

Group B

Wiring generally same as above [ Item No.1.a] but for one light point controlled by 2 nos. 6A 2 Way switch

STAIR CASE POINT:Supply & Wiring generally same as above [ Item No. 1.a] but for one Staircase light point controlled by 2 Nos. 6A 2 Way switch.

Group B

Step type electronic regulator

Group B

CIRCUIT & POWER POINT WIRING: Supply & Wiring of circuits using 2 Runs of 1.5 Sq.mm. 1.1 KV grade ISI marked PVC insulated single core stranded copper wire with 14 SWG bare copper wire for earthing through 20/25 mm dia. medium duty electrical grade ISI marked PVC conduit in recessed system.

Supply & Wiring of Power Points using 2 Runs of 2.5 Sq.mm. 1.1 KV grade ISI marked PVC insulated single core stranded copper wire with 14 SWG bare copper wire for earthing through 20/25 mm dia. Meadium duty electrical grade ISI marked PVC conduit in recessed system.

Supply & Wiring of Power Points using 2 Runs of 4 Sq.mm. 1.1 KV grade ISI marked PVC insulated single core stranded copper wire with 14 SWG bare copper wire for earthing through 20/25 mm dia. Medium duty electrical grade ISI marked PVC conduit in recessed system.

metal box -150mm x75mm

3 -pin socket

5 Amps switch

1 No.6/16A 3 pin combined modular type shuttered socket controlled by 1No. one way 16A SP switch

metal box -150mm x75mm

15/16 Amps socket

15/16 Amps switch

wiring for 15/16 plug point

Wall mount light /Tubelights and accessories

Installation charges

supply of 1200mm sweep ceiling fan with all standard acessories without regulator.

Installation charges

supply of 450mm sweep light duty exhaust fan

Installation charges

TELEPHONE/ TV / DATA CONDUITING AND WIRING:Supply, installation, testing and commissioning of following types of and outer cover, in existing suitable size metal boxes recessed in walls including termination etc. complete as required RJ 11 Telephone Socket

TV Socket [ co-axial]

RJ 45 UTP Information Outlets

Supply, Wiring , termination and testing of 2pair 0.5 mm dia annealed high conductivity Copper conductor, PVC insulated unarmoured telephone wire through existing 20mm dia medium duty PVC conduit from TDJB to telephone socket complete as required

Supply, Wiring , termination and testing of TV Co-axial copper conductor PVC insulated RG-6 cable through existing 20/25mm dia medium duty PVC conduits complete as required

Supply, Wiring , termination and testing of UTP 4 Pair Cat 6 cable through existing 20/ 25mm dia medium duty PVC conduits complete as required

Supply, installation, testing and commissioning of following Telephone Distribution Junction Boxes[TDJB] with crone type terminals with hinged lockable door, detachable gland plate at the bottom / top complete with termination and connections of incoming / outgoing cables, complete as required. 5 Pair

Spply and laying of following sizes of medium duty PVC conduits along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit complete as required 20 mm

Group B

Wiring generally same as above [ Item No.1.a] but for one light point controlled by 2 nos. 6A 2 Way switch

Group B

Step type electronic regulator

POWER PLUG / UPS PLUG POINT WIRING: POWER OUTLETS / SWITCHES :Supply, Fixing, testing & commissioning of the following Modular type 230V Plug Sockets, Controlling Switches with suitable size metal box , innerbase plate , outer cover, termination of wires, earthing the box etc.complete as required . 1 No. 6A 2/3 pin combined Modular type shuttered socket controlled by 1 No .one way 6A SP switch metal box -150mm x75mm

3 -pin socket

5 Amps switch

Wall mount light /Tubelights and accessories

Installation charges

CEILING/EXHAUST FANS: Supply, Installation, testing and commissioning of the following ceiling fans, exhaust fans as per standards with all wiring, terminations, interconnections etc. complete as required, supply of 1200mm sweep ceiling fan with all standard acessories without regulator.

Installation charges

Existing DBs,cables,wires,switches checking and correcting damages etc.

SANITARY AND CP INSTALLATION: Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing PTMT pillar cock of approved quality and colour -15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. - 15 mm nominal bore

Supplying and installing approved make Health Faucet) with tube and Wall hook including cost of all fittings.

Supplying and installing approved make CP angle valve with Flange for inlet to Flush tanks, Wash basins, Urinals, Health Faucets etc. including cost of all fittings.

Supplying, conveying to position cleaning and installing approved make Cockroach trap, 203 mm dia Stainless steel Round multi purposes floor drain for inter connecting waste lines including cost of all fittings.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88mm, weighing not less than 190 gms

Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms..

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. - 15 mm nominal bore( for external)

Supplying of PVC SWR pipes, ring type approved make 6kg/cm2 class conveying to position, cleaning laying and jointing, including all leads and lifts to true lines and levels, PVC(SWR) pipes 110mm

Supplying of PVC SWR pipes, ring type approved make 6kg/cm2 class conveying to position, cleaning laying and jointing, including all leads and lifts to true lines and levels, PVC(SWR) pipes 75mm

Supplying conveying to position, cleaning laying and jointting, including all leads and lifts to true lines and levels, PVC (6kgf/cm2) pipes and specials approved make having ISI marking conforming to IS:4985 and PN16/ Heavy PVC specials through vertical or horizontal ducts110mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVCwaste fittings

Existing wash,concealed drain pipes cleaning and correcting.

Existing WC, concealed waste line ,CP fittings dismatling and correcting concealed lines,soil and waste line for toilets including all other accessories and misscelaneous works