Repair and renovation of office of SDO jagraon canal sub division and Zilledar jagraon at Akhara

Amount

Dismantling Cement concrete plain 1:3:6 mix

Scraping Lime Plaster

Scraping Mud Plaster

First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth.

First class burnt brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level.

First class 225mm thick honey-comb burnt brick work laid in cement sand mortar 1:4

Earth work in excavation in foundations, trenches.

Cement concrete 1:8:16 with stone ballast 20 mm gauge in foundation and plinth ( mixing by manual means)

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone aggregate 40mm gauge and 100 mm fine sand using mechanical mixer for mixing of material

Centring and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels.

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Extra for bitumen painting @0.69 kg per sqm

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure.

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.

Bottom Khurra on ground 1.2m x 0.6m consisting of brick on-edge laid in cement mortar 1:3 over 75mm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3.

Embedding 100mm dia CI rain water non pressure ISI mark pipe in cement mortar during masonry work.

Providing and fixing cast iron shoe for rain water pipe on wooden plugs fixed on wall face including filling the joints with spun yarn and cement mortar 1:2.

Cement concrete 1:4:8 with stone ballast 40mm gauge mixing by manual means

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS :15622 (size 600 x 300 mm) as approved by Engineer-in-Charge over 12 mm thick bed of cement Mortar 1:4

Providing and laying vitrified floor tiles of different sizes in light colour shades made using Double Charge technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete.(600 mmx600mm)

Raking out joints in lime or cement mortar and preparing the surface for repointing or replastering including cost of neat coat of cement , disposal of rubish to the dumping ground within 50 m lead

12.5 mm thick cement plaster 1:3

20 mm thick cement plaster 1:4 in two coat work

Providing and fixing chicken mesh for brick work , complete

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish.

Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats).

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing.

Water proofing treatment of Roof Slab with High performance cementitious two component product, consisting of a powder component and an acrylic polymer using two coats ( Dr Fixit Roofseal flex - Packaging Size: 12 .5 kg (7.5 kg powder + 5 kg polymer) / equivalent water proofing Solution ). The slurry thus formed by mixing the two, is to be applied on new roofs to forms a seamless, highly elastic, non-toxic waterproofing layer on the roof with a life expectancy of 7 years. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge.

Steel work fixed independently without connecting plates including cutting hoisting and fixing in position for Tees angles & channels

Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.

Cement concrete 1:3:6 with stone ballast or shingle mixing by manual means

Chowkats of commercial hard wood such as Hollock confirming to ISI specification no 1003 m kiln seasoned of doors and windows including iron hold fasts, corner straps cleats, stops, bolts for hold fasts etc, complete fixed in position Double Rebate (60mm x 150mm)

Hollock wood doors shutter windows shutter including hinges, screws, chocks, cheats, stops cords etc. complete fixed in position. (35 mm thick)

Wire guage Hollock wood doors shutter without springs housed in chowkhat. (35 mm thick)

Wire gauge fixed on chowkats with 25mm thick Hollock wood cover molding of full width.

Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position. Commercial with elm or gurjan facing on both \ Sides with laminated core and lipped edges:- 35 mm thick

Providing and fixing iron helical door spring 150mm (superior quality) including necessary screws, complete (iron helical spring)

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete I.S.I Designation No. III (size of door 851mm to 1000mm)

Providing & fixing 4" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Providing & fixing 6" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Providing & fixing 4" stainless steel tower bolts ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Providing & fixing 6" stainless steel tower bolts ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge.

Iron Fitting ISI Marked (d) Sliding Bolt 250mm

Providing & Fixing glass panes with nails and putty or wooden strip complete in all respect (Glazing area above 0.09 sqm) 5.0mm thick Plate glass (INDIAN)

Providing and fixing curtain rail 1.90cmchrome-plated with end bracket. Including sockets and brackets

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/25mm dia (ISI Marked) recessed in wall etc. (i)Wiring fan point (Without fan box)

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/25mm dia (ISI Marked) installed on surface etc., (ii) Wiring light point.

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/25mm dia (ISI Marked) installed on surface etc., (v) Wiring 6Amp. Plug control comprising wall socket point.

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/25mm dia (ISI Marked) installed on surface etc., (vi) Wiring 16/20Amp. power plug control point .

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in charge:- (iv) Overall size 4sq.mm (Un-sheathed)

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in charge:- (iii) Overall size 2.5sq.mm (Un-sheathed)

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in charge:- (ii) Overall size 1.5sq.mm (Un-sheathed) .

Supply & erection of Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface) (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy gauge PVC conduit pipe 25 mm dia

Supply and erection of sheet metal SP&N Double Door Distribution Board 12 way each with IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars,earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers.

Supply and erection of MCB Double Pole 50, 63amp. (10kA, Curve-C) for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts.

Supply and erection of MCB Single Pole 6-32amp. (10kA, Curve-C) for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts.

Supply and erection of MCB Single Pole 50-63amp. (10kA, Curve-C) for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts.As per CSR Item No 34.16 A (iv)

Supply and erection of Ceiling Rose (Flush Piano type) switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.

Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- (xi) 6/10amp. One Way Modular Switch (One Module)

Supply and erection of switches, sockets and other accessories (flush piano type/modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc:- (xvii) 25amp. Universal Modular Shuttered Socket (two Module)

Supply and erection of switches, socketsand other accessories (flush piano type/modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- 3 Pin Plug Top 6Amp. (ISI marked)

Supply and erection of switches, socketsand other accessories (flush piano type/modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:- 3 Pin Plug Top 25Amp. (ISI marked)

Supply and erection of 3-Stepped steel tubular swaged and welded pole (410-SP- Mpa) of Overall length 7 metre, with planting depth 1.25 metre, length of sections 4 metre, 1.5 metre and 1.5 metre (Bottom, Middle and Top respectively), Outer dia and thickness of sections 114.3mm x 4.5mm, 88.9mm x 4.05mm and 76.1mm x 3.25mm (Bottom, Middle and Top respectively) with approximate weight 73 kg. (410 SP-2) and base Plate weight 7.5 kg. of size 12mm thick about 30 cm dia.

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition. Size 75 mm x 75 mm

Providing and fixing in position 15mm C.P. Pillar cock foam flow of approved make (to the approval of Engineer-in-charge)

Providing & Fixing in position C.P. Brass Hexa Nipple 15mm of approved make (to the approval of Engineer-in-charge ) complete in all respect.

Providing and fixing in position towel rails ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect. (C.P. brass towel rails size 15 mm dia 610 mm long)

C.P. brass towel rack 600mm long with lower hangers

C.P. brass Bib cock with Wall flange

C.P. brass 15mm Concealed stop cock with adjustable wall flange with seal. (outer + inner body)

C.P. Brass Wall mixer with Non telephonic shower arrangement.

Aluminium khunti with 6 pegs

Providing and fixing C.P.brass 15mm Angular stop cock with wall flange.

Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. (i) PTMT 20mm concealed stop cock with flange

Providing & Fixing in position C.P. Brass extension piece i) C.P. Brass extension piece, 25mm long to 50mm long

Providing and fixing in position C.P. brass soap dish.

Providing & fixing in position PVC tube connection of size 15mm x 450 mm with C.P. Brass nut of approved make (to the approval of Engineer-in-charge ) complete in all respect.

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standarddesign minimum depth of water should be 150 mm with a minimum seal 50mm. 100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg.and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm

Providing & Fixing in postion Acrylic liquid soap container (to the approval of Engineer-in-charge ) complete in all respect.

Making connection with the existing G.I. branch main up to 40mm size pipe including cutting of existing pipe line, threading of pipe lines from both ends and fixing of G.I Tee etc. in the pipe line (including cost of G.I Tee) complete in all respects

Providing and fixing in position automatic brass Ball Cock in tanks (A) Brass Ball Cock with rod and Plastic Ball of 25mm i/d

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. elbow 90 degree (All sides socketed)

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. for vent cowls

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. . (for P-trap/Floor Trap 110 mm x 75 mm)

Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification of reputed firm of the self cleaning design with S.S. grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc.With 100mm x 75mm i/d Floor Trap (weighing 5.8 Kg)

Providing and fixing in position SWR UPVC soil waste vent or antisyphonage pipes 110mm o/d SWR UPVC pipe line laid complete

Providing and fixing 110 mm dia SWR U.P.V.C Rain water pipe of 4 kgf/sqm as per IS 4985

Providing and fixing 110 mm dia U.P.V.C bend for Rain water pipe as per IS:14735 including jointing

Providing and fixing in position Grating of approved make (to the approval of Engineer in charge)150 mm x 150 mm . For gully trap PVC Grating (P.T.M.T)

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. (20mm i/d)

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. (25mm i/d)

Providing and fixing PVC waste pipe Collapsiable 32mm complete in all respect.

Providing and fixing in position Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) with P trap or S trap of approved make (to the approval of the Engineer in-charge) and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Providing and fixing in position Vitreous Chinaware white urinal with concealed or in built P-trap (size 310x370x640 mm) with built in water seal, outlet to wall and water inlet from back of approved make (to the approval of Engineer-in-charge) complete in all respect..

Providing and fixing C.P. brass Urinal Spreader Ocular-Regular complete with fittings for urinals complete.

Providing and fixing jet spray with 2'-6" long . with CP brass nut

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -incharge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. (ii) Double Layer Tanks

Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-incharge) in PVC Water storage tanks complete in all respect G.I. tank nipple 25mm i/d

Providing and fixing vitreous chinaware pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect. Vitreous chinaware standard white pedestal for wash hand basin.

Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification of reputed firm of the self cleaning design with S.S. grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc. (a) With 100mm x 75mm i/d Floor Trap (weighing 4.0 Kg)

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge) (a) Size 600mmx450mm

Making connection with the existing G.I. branch main up to 40mm size pipe including cutting of existing pipe line, threading of pipe lines from both ends and fixing of G.I Tee etc. in the pipe line (including cost of G.I Tee) complete in all respects

Any other Item

BIRDEVINDER SINGH GILL CONTRACTOR