GENERAL-Dam Safety- Providing SS handrails at dam top view points and fabricating, strengthening and erecting galvanised covers of RBC, LBC emergency and sluice openings at Malampuzha Dam.-General Mechanical Work

Amount

DISMANTLING existing MS structures at 3 Nos. Dam top view points

15.18:Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,boltd, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

DEMOLISHING existing concrete pier at 3 Nos. Dam top view points

15.1:Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead as per direction of Engineer - in- Charges.

Providing reinforcements and CONCRETING at 3 Nos. Dam top view points.

OD8366/2022-2023:DRILLING and FASTENING with TMT rod in concrete/Stone including conveyance and labor charges complete excluding cost of materials already supplied.

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD8367/2022-2023:Supply of 50 mm dia PVC pipe

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

Supply of SS square tubes, plates and MS HOT DIP GALVANISED material, fabrication and erection for HANDRAIL at 3 Nos. Dam top view points

OD8233/2022-2023:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Materials in 304 Grade as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete

OD8235/2022-2023:Supply of SS BOLT and NUT up to 300mm Length including cost of conveyance.

OD8236/2022-2023:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD8237/2022-2023:Supply of MS chequered plates including cost of conveyance charges

OD8238/2022-2023:Fabrication and supply of Structural steel MS Materials ( Up to 2 tonne weight ) as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

OD8241/2022-2023:LOADING and UNLOADING charges for materials

OD8243/2022-2023:HOT DIP GALVANISING the fabricated work piece to get a minimum coating thickness of 80 microns. (The work piece is to be caustic cleaned for removing impurities like grease, dirt etc. then it is pickled to remove oxides and is then given flux coating to prevent further oxidation and is then finally dipped in zinc bath)

OD8244/2022-2023:Erection of the MS Materials ( Up to 2 Tonne weight ) including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied

8.2.2.2:Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

Strengthening and galvanising existing cover-1 and cover-2 for 1 No.RBC and 3 Nos. LBC sluice openings at dam top.

OD8247/2022-2023:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD8248/2022-2023:Fabrication and supply of Structural steel MS Materials ( Up to 2 tonne weight ) as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

OD8249/2022-2023:LOADING and UNLOADING charges for materials

OD8250/2022-2023:CONVEYANCE charge for materials. Data Observed for the conveyance for 100km (Enquired from market Rs. 40 for one way hence Rs. 80 for two way)

OD8293/2022-2023:HOT DIP GALVANISING the fabricated work piece to get a minimum coating thickness of 80 microns. (The work piece is to be caustic cleaned for removing impurities like grease, dirt etc. then it is pickled to remove oxides and is then given flux coating to prevent further oxidation and is then finally dipped in zinc bath)

OD8294/2022-2023:Erection of the MS Materials ( Up to 2 Tonne weight ) including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied

Dismantling emergency opening covers at 1 No. RBC and 3 Nos. LBC emergency openings at Dam top.

15.18:Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,boltd, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Demolishing concrete at 1 No. RBC and 3 Nos. LBC emergency openings at dam top.

15.1:Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead as per direction of Engineer - in- Charges.

Providing reinforcements and CONCRETING at 1 No. RBC and 3 No. LBC emergency openings at Dam top.

OD8296/2022-2023:DRILLING and FASTENING with TMT rod in concrete/Stone including conveyance and labor charges complete excluding cost of materials already supplied.

OD8297/2022-2023:DRILLING and FASTENING with EXPANSION BOLT M12x75 mm length in concrete including conveyance and labor charges complete.

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD8298/2022-2023:Supply of SS BOLT and NUT up to 300mm Length including cost of conveyance.

OD8299/2022-2023:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Materials in 304 Grade as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

Fabrication of emergency opening covers at 1 No. RBC and 3 Nos. LBC emergency openings at Dam top.

OD8314/2022-2023:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD8318/2022-2023:Supply of MS chequered plates including cost of conveyance charges

OD8319/2022-2023:Fabrication and supply of Structural steel MS Materials ( Up to 2 tonne weight ) as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

OD8320/2022-2023:LOADING and UNLOADING charges for materials

OD8321/2022-2023:CONVEYANCE charge for materials. Data Observed for the conveyance for 100km (Enquired from market Rs. 40 for one way hence Rs. 80 for two way)

OD8323/2022-2023:HOT DIP GALVANISING the fabricated work piece to get a minimum coating thickness of 80 microns. (The work piece is to be caustic cleaned for removing impurities like grease, dirt etc. then it is pickled to remove oxides and is then given flux coating to prevent further oxidation and is then finally dipped in zinc bath)

OD8324/2022-2023:Erection of the MS Materials ( Up to 2 Tonne weight ) including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied

P.Damodaran, G.R.Industries

steel industrials kerala ltd

Bidder Name

MOHAMMED MUSTHAFA V

P.Damodaran, G.R.Industries

steel industrials kerala ltd