Construction of toilet and cage for dogs at MC Dog Kennel at Khaliyar W. No. 1

Amount

Earth work in excavation by mechanical means(Hydraulic excavator/manual means in foundation, trenches or drains (not exceeding 1.5 mtr in with or 10 sqm on plan, including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 mtr, any kind of soil.

Providing and laying in position cement concrete of grade 1:4:8 (1 cement :4 coarse sand: 8 stone aggregate 40mm nominal size) excluding cost of centering and shuttering - all work upto plinth level.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1cement:6course sand:12 graded stone aggregate 20mm nominal size upto plinth level with CM 1:6 (1 cement : 6 course sand).

Brick work with common burnt clay F.P.S. (Non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in cement mortar 1:6 (1 cement : 4 coarse sand)

Centering and shuttering including strutting, propping etc and removal of form for suspended floors, roofs, landing, balconies and access platform

Centering and shuttering including strutting, propping etc and removal of form for Edges of slabs and breaks in floors and walls under 20 cm wide

Centering and shuttering including strutting, propping etc and removal of form for Lintels, beams, plinth beams, giders, bressumes and cantilever

Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size), in beams, suspended floors, roof , landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement

Steel reinforcement for RCC Work including straightening, cutting, bending, placing in position and binding all complete using Thermo-Mechanically Treated bars of grade Fe 500D or more

Boulder soling under floor/road/path dry hand packed tightly using boulders of size 5 cm to 15 cm.

Providing and laying in position cement concrete of grade 1:2:4 (1 cement :2 coarse sand: 4 stone aggregate 40mm nominal size) excluding cost of centering and shuttering - all work upto plinth level.

12 mm thick Cement plaster of mix 1:4 (1 cement : 4 fine sand)

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand

6mm thick cement plaster of mix 1:3 (1 cement : 3 fine sand) in ceiling

Providing and laying ceramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved made in all colours shades except of any size as approved by Engineer-n-charge, laid over 20mm thick bed of cement mortar 1:4 (1cement : 4 coarse sand) and joiting with grey cement slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing 1st quality ceramic glazed tiles conforming to IS: 15622 of approved made in all colours shades except of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1cement : 3 coarse sand) and joiting with grey cement slurry @ 3.3 Kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on new work (two or more coat) over and including water thinable primer coat with cement primer

Finishing walls with water proofing cement paint of required shade on new work (two or more coats applied @ 3.84 Kg/10 Sqm)

Providing and fixing factory made PVC door frame made of PVC extruded sections of size 75mmx53mm having wall thickness 2.0mm (+/- 0.2mm). Both verticals sides of the frame reinforced with PVC profile of cross section size 28mmx30mmx2mm thickness (+/_ 0.2mm) and 75mmx200mm long, including reinforcing both ends at the top frame with PVC profice. PVC Door Frame and PVC reinforcement profile to be mitred cut, jointed and fusion welded together, including providing and fixing 3 nos of 125mm long stainless steel hinges to frame, fixing the frame with jamb with required nos & sizes of anchor dash fastener, all complete as per manufacturer's specification and direction of Engineer-in-Charge.

35mm thick factory non decorative finish (Matt finish) made solid panel PVC Door shutter and/or PVC glazed shutter for window/vent etc, made out of a single piece extruded solid PVC profiles, 5mm (+/- 0.2mm) thick, having slyles & rails (except lock rail) of size 95mm x 35mm x 5mm, out of which 75mm shall be flat and romm shall be tapered (on both side) having one side thickness of 15mm integrally extruded on the hinge side of profile for better scrows holding power, including reinforing with MS tube of size 40mmx20mmx1mm, joints of styles and rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & MS rectangular pipes bracket of size 190mm x 100mm of cross section size 35mmx17mmx1mm at each corner. Single piece extruded 5mm thick solid PVC Lock rail of size 115mm x 35mm, out of which 75mm to be flat and 20mm to be tapered at both ends, having 15mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125mm x 11mm, including providing 5mm single piece solid PVC extruded sheet in the door panel and/or 5mm thick sheet glass in window/ventilator panels, all as complete as per manufacturer's specification and direction of Engineer-in-charge

Providing and fixing ISI marked oxidised MS Tower bolt black finish (Barrel type) of size 150x10mm with necessary screws etc complete.

Providing and fixing ISI marked oxidised MS Tower bolt black finish (Barrel type) of size 100x10mm with necessary screws etc complete.

Providing and fixing ISI marked oxidised MS Slidng door bolt of size 200x16mm with nuts and screws etc complete

Providing and fixing ISI marked oxidised MS handles 125mm conforming to IS 4992 with necessary screws etc complete

Providing and fixing ISI marked oxidised MS handles 100mm conforming to IS 4992 with necessary screws etc complete

Providing and fixing white vitreous china pedestal type water closet (European type WC Pan) with ISI marked white solid plastic seat and lid, 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS;7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china wash basin size 550x400mm with CI Brackets, single 15mm CP brass pillar tap, 32mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wall whereve required.

Providing and fixing white vitreous chine pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing 32mm dia PVC waste pipe for sink or wash basin complete

Providing and fixing 100mm brass CP grating for floor trap

Providing and fixing 600x450mm bevelled edge mirror of superior glass complete with 6mm thick hard board ground fixed to wooden cleats with CP Brass screws and washers complete

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain and brass threaded fitting, i/c fixing the pipe with clamps at 1.0 m spaces in concealed work, including cutting chases and making good the walls etc using 15mm nominal outer dia pipes. This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain and brass threaded fitting, using 20mm nominal outer dia pipes. This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

Providing and fixing gun metal wheel with CI Wheel of approved quality (screwed end) 20mm nominal bore

Providing and fixing 20mm nominal bore ball valve (brass)) of approved quality, high pressure, with plastic floats complete.

Providing and fixing unplasticised PVC connection pipe with brass unions, 45 cm length 15mm nominal bore

Providing and fixing 15mm nominal bore CP Brass bib cock of approved quality conforming to IS 8931

Providing and fixing 15mm nominal bore CP brass angle valve for basin mixer and geyser point of approved quality conforming to IS 8931

Providing and fixing Jet for europeon type WC 15mm nominal bore and 1 mtr length of pipe all as directed

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS:12701 marked, with cover and suitable locking arrangement and making necessaary holes for inlet, outlet and overflow pipe but without fitting and the base support for tank

Constructing brick masonry manhole with common burnt clay FPS (non modular) bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) with RCC top slab with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominals size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2 :4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finishing with a floating coat of neat cement complete as per standard design with inside size 90x80 cms and 45 cms deep including CI cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg

Providing and fixing in floor unplasticised - PVC moulded 110x75 mm size floor trap including jointing with seal ring etc complete

Providing and fixing on walls or laid in floor 75mm diameter unplasticised Rigid PVC pipe single socketed conforming to IS 13592 Type A including jointing with seal ring

Providing and fixing on walls or laid in floor 110mm diameter unplasticised Rigid PVC pipe single socketed conforming to IS 13592 Type A including jointing with seal ring

Providing and fixing on walls or laid in floor unplasticised Rigid PVC mouldede fitting/accessories (Single Tee with door 75x75x75mm) for PVC pipes conforming to IS 13592 Type A including jointing with seal ring

Providing and fixing on walls or laid in floor unplasticised Rigid PVC mouldede fitting/accessories (Single Tee with door 110x110x110mm) for PVC pipes conforming to IS 13592 Type A including jointing with seal ring

Providing and fixing on walls or laid in floor unplasticised Rigid PVC moulded fitting/accessories (Bend 87 degree 110mm) for PVC pipes conforming to IS 13592 Type A including jointing with seal ring

Providing and fixing on walls or laid in floor unplasticised Rigid PVC moulded fitting/accessories (Bend 87 degree 75mm) for PVC pipes conforming to IS 13592 Type A including jointing with seal ring

Providing and fixing on walls unplasticised Rigid PVC pipe clips 75mm of approved designed to PVC pipes by means of 50mm screws and PVC rawl plug and making good the wall etc complete

Providing and fixing on walls unplasticised Rigid PVC pipe clips 110mm of approved designed to PVC pipes by means of 50mm screws and PVC rawl plug and making good the wall etc complete

Providing and fixing unplasticised Rigid PVC pipe vent cowl 75mm of approved designed to PVC vent pipes and fixing with suitable adhesive etc complete

Demolishing cement concrete/RCC half cut pipes manually/by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge, nominal concrete 1: 3:6 or richer mix(i/c equivalent design mix)

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete in floor

Neat cement punning on floor

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required in grating, frames, guard bar, ladder, railing, brackets, gates and similar works

Painting with synthetic enamel paint of approved brand and manufactures(Asian/Berger paint or its equivalent) of required colour to give an even shade on new work wooden or steel surfaces with two or more coat as required

Surjeet Guleria (BID ID -545412)

Tek Singh (BID ID -545540)