MVS on Hiramandalam Reservoir (Ph-1) for Tekkali and Narasannapeta constituencies in Srikakulam District, Est.Rs1204.00 Crores

Supply and delivery of HDPE PE-100 Pipes confirming to IS 4984/2016 with amendments & revisions. The rates are inclusive of cost, conveyance to site, loading and unloading charges and as directed by the Engineer-in-Charge including over heads and contractors profit @13.615% excluding GST for pumping mains and gravity mains for the following sizes

63mm dia HDPE PE-100, 6kgs/cm2 pipes

75mm dia HDPE PE-100, 6kgs/cm2 pipes

90mm dia HDPE PE-100, 6kgs/cm2 pipes

110mm dia HDPE PE-100, 6kgs/cm2 pipes

125mm dia HDPE PE-100, 6kgs/cm2 pipes

140mm dia HDPE PE-100, 6kgs/cm2 pipes

160mm dia HDPE PE-100, 6kgs/cm2 pipes

180mm dia HDPE PE-100, 6kgs/cm2 pipes

200mm dia HDPE PE-100, 6kgs/cm2 pipes

225mm dia HDPE PE-100, 6kgs/cm2 pipes

250mm dia HDPE PE-100, 6kgs/cm2 pipes

75mm dia HDPE PE-100, 8kgs/cm2 pipes

90mm dia HDPE PE-100, 8kgs/cm2 pipes

110mm dia HDPE PE-100, 8kgs/cm2 pipes

125mm dia HDPE PE-100, 8kgs/cm2 pipes

140mm dia HDPE PE-100, 8kgs/cm2 pipes

160mm dia HDPE PE-100, 8kgs/cm2 pipes

180mm dia HDPE PE-100, 8kgs/cm2 pipes

75mm dia HDPE PE-100, 10kgs/cm2 pipes

90mm dia HDPE PE-100, 10kgs/cm2 pipes

110mm dia HDPE PE-100, 10kgs/cm2 pipes

125mm dia HDPE PE-100, 10kgs/cm2 pipes

180mm dia HDPE PE-100, 10kgs/cm2 pipes

Construction of pipe line for Drinking Water Supply with HDPE PE-100 pipes including lowering, laying and jointing of pipeline as per IS7634-part-II/1975 with its amendments and revisions and as per Technical specifications as per requirements, lowering, laying and jointing of pipe lines with necessary HDPE specials true to alignment and gradient, trench excavation (Earth work excavation in all soils upto SDR using machine with 2/3rd and manual with 1/3rd) for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering and tamping and removing surplus earth from site of work and filling the pipeline with water and hydro-testing to the required pressure etc., complete for finished item of work as per the Standard Specifications and as directed by the Department Engineers. The rates are inclusive of all labour charges, HDPE specials etc., complete for finished item of pipeline work, including overheads and contractors profit @13.615% for pumping mains and gravity mains for the following sizes but excluding GST and Seigniorage charges.

63mm dia HDPE PE-100, 6kgs/cm2 pipe line with trench size 0.7m x 1.0m

75mm dia HDPE PE-100, 6kgs/cm2 pipe line with trench size 0.7m x 1.0m

90mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.7m x 1.0m

110mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.7m x 1.0m

125mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.7m x 1.0m

140mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.7m x 1.0m

160mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.8m x 1.1m

180mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.8m x 1.1m

200mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.8m x 1.1m

225mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.9m x 1.2m

250mm dia HDPE PE-100, 6Kgs/cm2 pipe line with trench size 0.9m x 1.2m

75mm dia HDPE PE-100, 8kgs/cm2 pipe line with trench size 0.7m x 1.0m

90mm dia HDPE PE-100, 8Kgs/cm2 pipe line with trench size 0.7m x 1.0m

110mm dia HDPE PE-100, 8Kgs/cm2 pipe line with trench size 0.7m x 1.0m

125mm dia HDPE PE-100, 8Kgs/cm2 pipe line with trench size 0.7m x 1.0m

140mm dia HDPE PE-100, 8Kgs/cm2 pipe line with trench size 0.7m x 1.0m

160mm dia HDPE PE-100, 8Kgs/cm2 pipe line with trench size 0.8m x 1.1m

180mm dia HDPE PE-100, 8Kgs/cm2 pipe line with trench size 0.8m x 1.1m

75mm dia HDPE PE-100, 10kgs/cm2 pipe line with trench size 0.7m x 1.0m

90mm dia HDPE PE-100, 10Kgs/cm2 pipe line with trench size 0.7m x 1.0m

110mm dia HDPE PE-100, 10Kgs/cm2 pipe line with trench size 0.7m x 1.0m

125mm dia HDPE PE-100, 10Kgs/cm2 pipe line with trench size 0.7m x 1.0m

180mm dia HDPE PE-100, 10Kgs/cm2 pipe line with trench size 0.7m x 1.0m

Supply & delivery of Centrifugally cast (Spun) Ductile Iron S/S Pipes as per IS:8329/2000 with its amendments and revisions suitable for push-on-joint (rubber gasket jointing) with cement mortar lining inside the pipes with outside zinc coating. The rates are inclusive of cost, conveyance to site, loading and unloading charges and as directed by the Engineer-in-Charge including over heads and contractors profit @13.615% excluding GST for pumping mains and gravity mains for the following sizes.

150 mm dia DI K7 Pipes

200 mm dia DI K7 Pipes

250 mm dia DI K7 Pipes

300 mm dia DI K7 Pipes

350 mm dia DI K7 Pipes

400 mm dia DI K7 Pipes

500 mm dia DI K7 Pipes

700 mm dia DI K7 Pipes

100 mm dia DI K9 Pipes

150 mm dia DI K9 Pipes

200 mm dia DI K9 Pipes

250mm dia DI K9 Pipes

300mm dia DI K9 Pipes

350mm dia DI K9 Pipes

400mm dia DI K9 Pipes

450mm dia DI K9 Pipes

500 mm dia DI K9 Pipes

700mm dia DI K9 Pipes

Construction of pipe line for Drinking Water Supply with Centrifugally Cast Ductile Iron S/S Pipes as per IS Specifications with its amendments and revisions and as per Technical specifications as per requirements, lowering, laying and jointing of pipe lines with necessary DI specials true to alignment and gradient, trench excavation (Earth work excavation in all soils upto SDR using machine with 2/3rd and manual with 1/3rd) for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering and tamping and removing surplus earth from site of work and filling the pipeline with water and hydro-testing to the required pressure etc., complete for finished item of work as per the Standard Specifications and as directed by the Department Engineers. The rates are inclusive of all labour charges, specials etc., complete for finished item of pipeline work, including overheads and contractors profit @13.615% for pumping mains and gravity mains for the following sizes but excluding GST and Seigniorage charges

150 mm dia DI K7 pipe line with trench size 0.9x1.2m

200 mm dia DI K7 pipe line with trench size 0.9x1.3m

250 mm dia DI K7 pipe line with trench size 0.9x1.3m

300 mm dia DI K7 pipe line with trench size 0.9x1.3m

350 mm dia DI K7 pipe line with trench size 1.0x1.4m

400 mm dia DI K7 pipe line with trench size 1.0x1.4m

500 mm dia DI K7 pipe line with trench size 1.1x1.6m

700 mm dia DI K7 pipe line with trench size 1.3x1.8m

100 mm dia DI K9 pipe line with trench size 0.9x1.3m

150 mm dia DI K9 pipe line with trench size 0.9x1.3m

200 mm dia DI K9 pipe line with trench size 0.9x1.3m

250 mm dia DI K9 pipe line with trench size 0.9x1.3m

300 mm dia DI K9 pipe line with trench size 0.9x1.3m

350 mm dia DI K9 pipe line with trench size 1.0x1.4m

400 mm dia DI K9 pipe line with trench size 1.0x1.4m

450 mm dia DI K7 pipe line with trench size 1.0x1.4m

500 mm dia DI K9 pipe line with trench size 1.1x1.6m

700 mm dia DI K9 pipe line with trench size 1.3x1.8m

Manufacturing, Supply, Delivery of Double chambered restrained joint DI K9 Pipes confirming to IS 8329 (restrained joints are to IS 8329 (restrained joints are designed and tested as per ISO 10804) (to be used to for minimum 10804) (to be used to for minimum required length as per design along with double chambered restrained DI fittings to avoid concrete thrust block at bends) including rubber gaskets confirming to IS 5382 -1985 /8329-2000 with latest amendments and locking bars& rubber spacers , conveying to work site, etc., complete including loading and unloading at both destinations, excluding cost of specials including over heads and contractors profit @13.615% excluding GST for pumping mains and gravity mains for the following sizes

100mm dia Double chambered restrained joint DI K9 Pipes

150mm dia Double chambered restrained joint DI K9 Pipes

200mm dia Double chambered restrained joint DI K9 Pipes

250mm dia Double chambered restrained joint DI K9 Pipes

300mm dia Double chambered restrained joint DI K9 Pipes

350mm dia Double chambered restrained joint DI K9 Pipes

400mm dia Double chambered restrained joint DI K9 Pipes

450mm dia Double chambered restrained joint DI K9 Pipes

500 mm dia Double chambered restrained joint DI K9 Pipes

700mm dia Double chambered restrained joint DI K9 Pipes

Construction of pipe line for Drinking Water Supply with Double chambered restrained joint DI K9 Pipes as per IS Specifications with its amendments and revisions as per Technical specifications as per requirements, lowering, laying and jointing of pipe lines with necessary Double Chambered Restrained Joint fittings confirming to IS 9523 : 2000 true to alignment and gradient, trench excavation (Earth work excavation in all soils upto SDR using machine with 2/3rd and manual with 1/3rd) for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering and tamping and removing surplus earth from site of work and filling the pipeline with water and hydro-testing to the required pressure etc., complete for finished item of work as per the Standard Specifications and as directed by the Department Engineers. The rates are inclusive of all labour charges excluding cost of specials and fittings etc., complete for finished item of pipeline work, including overheads and contractors profit @13.615% for pumping mains and gravity mains for the following sizes but excluding GST and Seigniorage charges.

100 mm dia DI K9 pipe line with trench size 0.9x1.3m

150 mm dia DI K9 pipe line with trench size 0.9x1.3m

200 mm dia DI K9 pipe line with trench size 0.9x1.3m

250 mm dia DI K9 pipe line with trench size 0.9x1.3m

300 mm dia DI K9 pipe line with trench size 0.9x1.3m

350 mm dia DI K9 pipe line with trench size 1.0x1.4m

400 mm dia DI K9 pipe line with trench size 1.0x1.4m

450 mm dia DI K9 pipe line with trench size 1.0x1.4m

500 mm dia DI K9 pipe line with trench size 1.1x1.6m

700 mm dia DI K9 pipe line with trench size 1.2x1.7m

Manufacture, Supplying and fitting Ductile Iron Double Chambered Restrained Joint fittings confirming to IS 9523 : 2000 (restrained joints are designed and tested as per ISO 10804) of Class K-12 (Alternative and to avoid concrete thrust blocks along with minimum length of Restrained joint DI pipes at bends) including rubber gasket confirming to IS 5382 : 1985 and locking bars & rubber gaskets, overheads and contractors profit @13.615%, etc complete but excluding Taxes.

Fittings upto 500mm dia

Fittings above 500mm dia

Centrifugally cast (spun) Ductile Iron Fittings conforming to IS:9523/2000 having dimensions as per table. The rates mentioned here under are for fittings, zinc coated externally with inside mortar lining (with finishing as per class 13/IS 9523/2000) (ex-works) Including Transportation, overheads and contractors profit @13.615% and all Taxes.

Fittings upto 500mm dia @ 160.6 kg/m.

Fittings above 500mm dia @ 177.2 kg/m.

Supply and delivery of GI Pipes confirming to IS 1239 with amendments & revisions. The rates are inclusive of cost, conveyance to site, loading and unloading charges and as directed by the Engineer-in-Charge including over heads and contractors profit @13.615% excluding GST for pumping mains and gravity mains for the following sizes.

80mm dia GI pipe -B class

100mm dia GI pipe -B class

Lowering, laying and jointing of medium grade GI pipes with GI fittings except GI bends, unions and GI connectors with checkout and socket including earthwork excavation and refilling the trenches with excavated soils etc., complete Tata or Zenith make or equivalent. The rates are inclusive of cost and conveyance of GI fittings and labour charges etc., complete for finished item of pipeline work, including overheads and contractors profit @13.615% but excluding GST and Seigniorage charges.

80mm dia GI pipe -B class

100mm dia GI pipe -B class

Manufacturing, Supply & delivery of Bar Wrapped Steel Cylindrical (BWSC) pipes (BIS marked) as per IS:15155-2002 including bends as per IS:7322 and with its amendments and revisions. The rates are inclusive of cost, conveyance to site, loading and unloading charges and as directed by the Engineer-in-Charge including over heads and contractors profit @13.615% excluding GST for pipelined for the follwing sizes.

450 mm dia BWSC 12 kgs/cm2 pipes

600 mm dia BWSC 12 kgs/cm2 pipes

Construction of pipe line for Drinking Water Supply with BAR WRAPPED STEEL CYLINDRICAL (BWSC) PIPES (BIS MARKED) AS PER IS:15155-2002 with its amendments and revisions including laying jointing, testing to Hydrostatic field test pressure including cost of site welding and fixing of Polypropylene Diapher cloth, cost transportation of water and emptying pipe line after completion of field testing. Laying and Jointing with propoer alignment and gradient, trench excavation (Earth work excavation in all soils upto SDR using machine with 2/3rd and manual with 1/3rd) for pipelines in all soils except rock requring blasting and refilling trenches with excavated earth (other than rocky soils and boulders) with watering and tamping and removing surplus earth from site of work and filling the pipeline with water and hydro-testing to the required pressure etc., complete for finished item of work as per the Standard Specifications and as directed by the Department Engineers. The rates are inclusive of all labour charges, specials etc., complete for finished item of pipeline work, including overheads and contractors profit @13.615% for pipelines for the following sizes but excluding GST and Seigniorage charges.

450 mm dia BWSC 12 Kgs/Sqcm pipes with Trench size of 1.0X1.4m

600 mm dia BWSC 12 Kgs/Sqcm pipes with Trench size of 1.1X1.6m

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) PN 1.6 Mpa with by-pass arrangement with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 including transportation, lowering, laying and fixing the valve in the pipeline including necessary specials, jointing materials, etc., including construction of RCC valve chamber of departmental approved size etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges, Overheads and Contractors Profit @13.615%, etc for finished item of work, but excluding GST for Pumping mains and Transmision lines.

Sluice Valves PN 1.6 on DI pipelines

100mm dia DI Sluice Valve on 100mm dia DI Pipeline

150mm dia DI Sluice Valve on 150mm dia DI Pipeline

200mm dia DI Sluice Valve on 200mm dia DI Pipeline

250mm dia DI Sluice Valve on 250mm dia DI Pipeline

300mm dia DI Sluice Valve on 300mm dia DI Pipeline

350mm dia DI Sluice Valve on 350mm dia DI Pipeline

400mm dia DI Sluice Valve on 400mm dia DI Pipeline

Sluice Valves PN 1.6 on HDPE pipelines

80 mm dia DI sluice valve on 63 mm dia HDPE line.

80 mm dia DI sluice valve on 75 mm dia HDPE line.

80 mm dia DI sluice valve on 90 mm dia HDPE line.

100 mm dia DI sluice valve on 110 mm dia HDPE line.

125 mm dia DI sluice valve on 125 mm dia HDPE line.

150 mm dia DI sluice valve on 140 mm dia HDPE line.

150 mm dia DI sluice valve on 160 mm dia HDPE line.

150 mm dia DI sluice valve on 180 mm dia HDPE line.

200mm dia DI Sluice Valve on 200mm dia HDPE line.

Supply and delivery of D.I double flanged Sluice Valves conforming to IS- 14846 (with up to date amendments, if any) including gear arrangements for the following dia. as per test pressure having Body, Bonnet, Dome, Stool cover, Wedge, Stuffing box, Gland, Thrust plate, Cap/Hand wheel with D.I; Stem, Body seat ring, Wedge facing ring, Bushes, Bolts, Nuts, Pinion and Pinion shaft with Stainless steel (IS 6603) ; Wedge nut, Shoe, Channel with Leaded Tin Bronze ( IS 318 ); Gasket with Neoprene Rubber; Gland packing with Rubber; Gear, Gear housing with Cast Steel and lowering, laying and fixing the valve in the pipeline including necessary specials, jointing materials, dismantling joints etc., including construction of RCC valve chamber of departmental approved size etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges, Overheads and Contractors Profit @13.615%, etc for finished item of work, but excluding GST for Pumping mains and Transmision lines.

Sluice Valves PN 1.6 on DI pipelines

450mm dia DI Sluice Valve on 450mm dia DI Pipeline

500mm dia DI Sluice Valve on 500mm dia DI Pipeline

700mm dia DI Sluice Valve on 700mm dia DI Pipeline

Sluice Valves PN 1.6 on BWSC pipelines

450mm Sluice Valve on 450mm dia pipeline

600mm Sluice Valve on 600mm dia pipeline

Supply, delivery and fixing of Tamper Proof DI Flanged Single Chamber Air Release Valves with body & cover made of Ductile Iron Grade GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 with Food Grade Epoxy Powder Coating(EP-P) (Min:250 Micron) inside and Outside of Color Blue RAL 5005. All internal parts such as Float, shell, Cove Bolts etc. made of Austenitic alloy steel of SS AISI 304/316 and DN 50 float of and other components with ABS/PTFE/EPDM/NBR and generally conforming to DIN/BIS/AWWA standards (or) combination Flange drilling as per IS - 1538 and including cost and supply of Air valve, required Specials to suit the pressure class of pipe, jointing material, lowering and fixing of valves including construction of RCC valve chamber of departmental approved size including cost and conveyance of all materials and labour charges etc., complete for finished item of work as per standard specification and as directed by the department Engineer. The rates are inclusive of cost and conveyance of all materials and labour charges, Overheads and Contractors Profit @13.615%, etc for finished item of work, but excluding GST and seigniorage charges.

Air Valves PN 1.6 on DI pipelines

40 mm dia DI valve on 100 mm dia DI pipe line

50 mm dia DI valve on 150 mm dia DI pipe line

50 mm dia DI valve on 200 mm dia DI pipe line

80 mm dia DI valve on 250 mm dia DI pipe line

80 mm dia DI valve on 300 mm dia DI pipe line

100 mm dia DI valve on 350 mm dia DI pipe line

100 mm dia DI valve on 400 mm dia DI pipe line

100 mm dia DI valve on 450 mm dia DI pipe line

150 mm dia DI valve on 500 mm dia DI pipe line

150 mm dia DI valve on 700 mm dia DI pipe line

Air Valves PN 1.6 on HDPE pipelines

40 mm dia DI valve on 75 mm dia HDPE pipe line

40 mm dia DI valve on 90 mm dia HDPE pipe line

40 mm dia DI valve on 110 mm dia HDPE pipe line

50 mm dia DI valve on 125 mm dia HDPE pipe line

50 mm dia DI valve on 140 mm dia HDPE pipe line

50 mm dia DI valve on 160 mm dia HDPE pipe line

50 mm dia DI valve on 180 mm dia HDPE pipe line

50 mm dia DI valve on 200 mm dia HDPE pipe line

Air Valve PN 1.6 on BWSC Pipeline

100mm Air Valve on 450mm dia BWSC pipeline

150mm Air Valve on 600mm dia BWSC pipeline

Supply and delivery of "Resilient Seated Soft Sealing" Gate Valves (Sluice Valves) PN 1.6 Mpa with by-pass arrangement with Body and Bonnet of Ductile Iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 and Wedge fully Rubber Lined with food grade quality grade W270 grade EPDM, Replaceable Spindle Nut without gland packing with 3-O ring protection system on the Shaft and Seals of NBR. The Valves should be Vacuum tight and 100% leak proof with face to face dimensions as BS:5163 Type A/IS:14846. All the valves should be with fusion bonded Electrostatic Powder coating both inside and outside (Min 250 Microns)- RAL 5005 with Pocket Less Straight through body Passage conforming to Design standards of DIN-3202F4/BS:5163 Type A Flange drilling as per IS - 1538 and lowering, laying and fixing the valve in the pipeline including necessary specials such as scour tee, double flanged pipes, duck foot bend, semicircular bend, ec., jointing materials, including construction of RCC valve chamber of departmental approved size etc.complete for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges, Overheads and Contractors Profit @13.615%, etc complete for finished item of work, but excluding GST for Scour arrangements

Scour Valves PN 1.6 on DI pipelines

80 mm dia scour valve arrangement on 100mm dia DI Pipeline

100 mm dia scour valve arrangement on 150mm dia DI Pipeline

125 mm dia scour valve arrangement on 200mm dia DI Pipeline

150 mm dia scour valve arrangement on 250mm dia DI Pipeline

150 mm dia scour valve arrangement on 300mm dia DI Pipeline

150mm dia scour valve arrangement on 350mm dia DI Pipeline

150mm dia scour valve arrangement on 450mm dia DI Pipeline

300mm dia scour valve arrangement on 500mm dia DI Pipeline

500mm dia scour valve arrangement on 700mm dia DI Pipeline

Scour Valve (PN 1.6) arrangement on HDPE lines

80 mm dia PN 1.6 valve on 63 to 125mm HDPE lines

100 mm dia PN 1.6 valve on 140 to 180mm HDPE lines

Scour Valves PN 1.6 on BWSC pipelines

300mm dia PN 1.60 Valve on 450 mm dia BWSC Pipeline

300mm dia PN 1.60 Valve on 600 mm dia BWSC Pipeline

Supply and delivery of DI D/F Tilting disc Swing Check Valves Slanted seated with maximum swing of 59 degree with metallic, corrosion proof and wear resistant seat faces, Body and Disc of ductile cast iron GGG-40/SG-400/15 or GGG-50/SG-500/7 or Equivalent as per IS1865, IS:3896-2 Shafts of stainless steel, shaft bearing of zinc free bronze and Integral body seat face & disc face with nickel-chromium overlay welding and micro finished. All the inside and outside of the body is to be coated with double coating of food grade epoxy liquid lacquer (EP-F) with minimum thickness of 150 microns, color: RAL 5005 Blue face to face dimensions according to EN 558-1/14/DIN 3202-F4, Flange dimensions according to EN1092-2/IS 1538 completed and lowering, laying and fixing the valve in the pipeline including necessary specials and jointing materials, including construction of RCC valve chamber of departmental approved size etc.complete, for finished item of work as per the standard specifications and as directed by the department Engineers. The rates are inclusive of cost and conveyance of all materials and labour charges, Overheads and Contractors Profit @13.615% , etc complete for finished item of work, but excluding GST for NRV.

Non Return Valve PN 1.6 on DI Pipeline

100 mm dia PN 1.6 Non return valve on 150mm DI Pipeline

200 mm dia PN 1.6 Non return valve on 200mm DI Pipeline

250 mm dia PN 1.6 Non return valve on 250mm DI Pipeline

500 mm dia PN 1.6 Non return valve on 500mm DI Pipeline

700 mm dia PN 1.6 Non return valve on 700mm DI Pipeline

RCC M-20 Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete excluding cost of steel and its fabrication charges, including Overheads and Contractors Profit @13.615% etc., complete but excluding GST and Seigniorage charges. for Thrust Blocks, Pedestral footings, Anchor Blocks

RCC M-20 Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete excluding cost of steel and its fabrication charges, including Overheads and Contractors Profit @13.615% etc., complete but excluding GST and Seigniorage charges. for Pedestrals, Bed Blocks, Supporting Blocks.

RCC M- 20 Nominal mix for Pipe encaswing works and CC road restoration (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete and including Overheads and Contractors Profit @13.615% etc., complete but excluding GST and Seigniorage charges.

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 500 grade as per IS Specifications of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges including 13.615% overhead charges & contractors profit but exlcuding GST etc., complete for finished item of work.

Railway crossing/Road crossing by adopting trenchless technology tunneling work through specialized pipe jacking method by erecting the equipment to true to the alignment and gradient, by hydraulic pipe jacking technique complete including tunneling, excavation in all types of soils including hard rock and construction of RCC chambers suitable to casing pipe pits, and conveyance charges of machinery and other required materials but excluding cost of encasing pipe, in co-ordination with the concerned authorities as per approved drawings and directed by the Engineer-in –Charge including 13.615% over head and contractor profit charges but excluding GST etc.complete item of work for the following dias.

800mm dia Crossing

900mm dia Crossing

1000mm dia Crossing

Manufacturing, supply and delivery of RCC S/S NP3 Pipes as per BIS : 458/2003 including cost and conveyance, overheads and Contractors Profit @13.615% and excluding taxes etc. complete for 1.00 Rmt. For Casing Pipe

300mm dia Casing pipe

350mm dia Casing pipe

400mm dia Casing pipe

800mm dia casing pipe

900mm dia casing pipe

100mm dia casing pipe

Supply and delivery of Electromagnetic Flow meter, manufacturer should have ISO 9001:2015 certification and flow meter testing conforming to ISO 17025-2017, Flow meter Tube: SS 304, Flanges: Carbon Steel as per DIN PN 10 or higher rating as per requirement, Liner: Hard Rubber or PTFE suitable for drinking water application, Grounding: Grounding Rings SS 304 / Grounding Electrodes of material SS 316, Coil Housing and Junction Box: SS 304 / Die Cast Aluminum / Carbon Steel with anticorrosive epoxy coating of minimum thickness 150 microns / equivalent as per EN ISO-12944 standard (as per the site condition), Ingress Protection: IP 68 for sensor and IP 67 for transmitter, Flow Transmitter Accuracy: +/- 0.5% of the measured value for velocities 0.5 m/sec and above, Display: Digital LCD/LED (backlit LCD / LED) Display, Instantaneous flow, Bi-Directional flow and Totalized flow, Cable between Flow Head and Transmitter: Maximum 25 meters including PVC conduit, Surge Arrester: To be provided, Power Supply and Output: 230 V AC or 24 V DC as applicable to Site condition and 4-20 mA HART, Compatible to SCADA/WEB Based Data acquisition System, Flow meter test lab certification should be provided from NABL approved lab/FCRI, including transportation to site and with 5 years Warranty. (Make: M/s Krohne Marshall / Endress+Hauser/ Yokogawa / Siemens/ Emerson/ABB/ or equivalent make). Including Overheads & Contractor Profit 13.615% and Excluding of GST.

Compound Wall of height 1.80 Mts with VRCC foundations, Columns, Plinth beams Superstructure with Brick Masonry in CM (1:6), Plastering to the walls on both inside and outside, Painting two coats over primary coat with water proof cement paint, MS gates including cost and conveyance of all materials and labour charges including 13.615% over heads and contractors profit but excluding GST and segniorage charges, etc., complete for finished item of work as per department approved designs and drawings.

Construction of Coumpound wall for 100 m Length

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH : For Foundations

Supply and filling with sand in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of all material and water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310) and contractors profit & over heads but excluding seignorage charges etc complete : For Foundations

Plain Cement Concrete (1:4:8) for foundations and under flooring bed using 40mm size hard, machine crushed granite from approved quarry including cost and conveyance of all materials to site, including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and overheads & contractors profit complete for finished item of work. (APSS No. 402)

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Columns footing

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Lintel Beams

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Beams

Brick Masonary with CM(1:6) using Second Class Bricks including cost and conveyance of all the materials etc complete

Cement plastering with CM(1:5),12mm thick including cost and conveyance of all the materials ect complete.

Painting to new walls with 2 coats of water proof cement paint of approved brand and shade over a base coat of approved cement primer grade 1 making three coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powred materials, including cost and conveyance of all materials t work site and alll operational, incidental, labour charges, etc coomplete for finshed item of the work as per SS 912 for internal.

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including soverhead charges & Contractors profit but exlcuding VAT and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Provision for MS Gates in kgs _ 3.5m X 1.5m

Construction of Coumpound wall for 200 m Length

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH : For Foundations

Supply and filling with sand in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of all material and water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310) and contractors profit & over heads but excluding seignorage charges etc complete : For Foundations

Plain Cement Concrete (1:4:8) for foundations and under flooring bed using 40mm size hard, machine crushed granite from approved quarry including cost and conveyance of all materials to site, including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and overheads & contractors profit complete for finished item of work. (APSS No. 402)

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Columns footing

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Lintel Beams

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Beams

Brick Masonary with CM(1:6) using Second Class Bricks including cost and conveyance of all the materials etc complete

Cement plastering with CM(1:5),12mm thick including cost and conveyance of all the materials ect complete.

Painting to new walls with 2 coats of water proof cement paint of approved brand and shade over a base coat of approved cement primer grade 1 making three coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powred materials, including cost and conveyance of all materials t work site and alll operational, incidental, labour charges, etc coomplete for finshed item of the work as per SS 912 for internal.

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including soverhead charges & Contractors profit but exlcuding VAT and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Provision for MS Gates in kgs _ 3.5m X 1.5m

Construction of Coumpound wall for 1000 Mtr. Length

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH : For Foundations

Supply and filling with sand in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of all material and water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work. (APSS NO. 309 & 310) and contractors profit & over heads but excluding seignorage charges etc complete : For Foundations

Plain Cement Concrete (1:4:8) for foundations and under flooring bed using 40mm size hard, machine crushed granite from approved quarry including cost and conveyance of all materials to site, including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and overheads & contractors profit complete for finished item of work. (APSS No. 402)

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Columns footing

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Lintel Beams

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete for Beams

Brick Masonary with CM(1:6) using Second Class Bricks including cost and conveyance of all the materials etc complete

Cement plastering with CM(1:5),12mm thick including cost and conveyance of all the materials ect complete.

Painting to new walls with 2 coats of water proof cement paint of approved brand and shade over a base coat of approved cement primer grade 1 making three coats in all to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powred materials, including cost and conveyance of all materials t work site and alll operational, incidental, labour charges, etc coomplete for finshed item of the work as per SS 912 for internal.

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 415 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including soverhead charges & Contractors profit but exlcuding VAT and other taxes on all materials etc., complete for finished item of work in all floors.( APSS No.126)

Provision for MS Gates in kgs _ 3.5m X 1.5m

Hard rock required blasting with Air compressor including breaking rock, Gelatin, Detonator Electric etc with all labour charges and including 13.615% over head and contractor profit charges but excluding GST & seiniorage charges etc. complete item of work.

Cutting open C.C. road surface with concrete saw cutter and removal with Breaker for pipeline trenches including all labour charges, including 13.615% over heads and contractor profit but excluding GST & seiniorage charges etc. complete item of work.

PCC M- 20 Nominal mix for Pipe encaswing works and CC road restoration (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete and including Overheads and Contractors Profit @13.615% etc., complete but excluding GST and Seigniorage charges.

Supply of magnetically coupled, multijet, inferential type, dry dial Class-B water meters (Screwed end) AMR compatible manufactured in accordance with ISO 4064 standards and its latest ammendments/IS 779/1994 and its latest ammendments and shall have ISI/EEC/MID pattern approval (valid life cylce certificate and IP 68 protection from FCRI, GOI). including Overheads and Contractors Profit @13.615% etc., (excluding all taxes with 3 years warranty)

Construction of Functional Household Tap Connections (FHTC) on pipeline with 1/2" service connection with supply & fixing of PP Clamp Saddle manufactured by injection moulding (virgin resin of PE-80/PE-100 having blue /black colour using food grade compound raw material with quality assurance cerificate for usage in drinking water system and having working pressure of 10 bar with 1/2" service connection) and supply and fixing of required materials such as Non-return cum flow control valve (with all three parts made by using solid steel bars of 316, wth CNC machine make and of 15mm dia designed for 5 LPM discharge @ 0.50 bar pressure loss, not exceeding the flow of 7 LPM at 1 bar pressure and working on float principle as per CPHEO manual), compression fittings (ISO:17885-2015, PN 16 rating and manufactured from virgin resin of PE-80 having blue colour. Raw material must be as per BS:6920 for effect on water quality, should have moulded in SS 304 threded insert outlet with threded dimension conforming to IS 554/1507 which are Compression male/female threaded adaptor (with SS insert D20 mmx 1/2"), Compression male/female threaded elbow (with SS insert D20 mmx 1/2")), including supply, delivery and fixing of 15mm Nominal Bore GI pipe Medium Grade as per IS1239 with necessay GI fittings including 20mm dia HDPE pipe 16 Kg/cm2 pipes, earth work of trench excavation up to 0.50m depth) and 12.7mm dia Brass Bib cock(long body) Indian make heavy duty tap excluding GST and seigniorage charges but including over heads & contractors profit @ 13.615% etc. complete for finished item of work.

On 63 mm to 90 mm Dia Line

Construction of various capacities of OHBRs with M30 grade design mix with Fe 500 HYSD steel at the site selected by the department, as per drawing and specified in Technical specificastion including earth work excavation in all types of soils for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete as per the standard specifications . The rates are inclusive of DI verticals for all inlet, outlet, overflow and scour connections and valves. All valves near inlet, outlet and scour shall be D.I valves of heavy duty confirming to the specification of SoR. The rate is inclusive of cost and conveyance of all materials, vertical connections and labour charges, etc., complete for finished item of work, including Overheads and Contractors Profit @13.615% but excluding GST and Seigniorage charges.

20 KL OHBR - 12.45 Mts Staging

40 KL OHBR - 12.95 Mts Staging

40 KL OHBR - 16.05 Mts Staging

40 KL OHBR - 30 Mts Staging

60 KL OHBR - 30 Mts Staging

200 KL OHBR - 13.35 Mts Staging

250 KL OHBR - 13.45 Mts Staging

Cosctruction of RCC GLBRs with M30 grade mix with required Fe 500 HYSD Steel and its fabrication including earth work excavation for foundations, laying of PCC for levelling course below base slab, epoxy coating, impervious coat over the roof slab, plastering to the side walls and roof slab both inside and outside, providing all pipe connections and fixures, etc., including cost and conveyance of all materials and labour charges, including Overheads and Contractors Profit @13.615% etc., complete for finished item of work as per department approved designs and drawings but excluding GST and Seigniorage charges .

Cosctruction of RCC Sumps with M30 grade mix with required Fe 500 HYSD Steel and its fabrication including earth work excavation for foundations, laying of PCC for levelling course below base slab, epoxy coating, impervious coat over the roof slab, plastering to the side walls and roof slab both inside and outside, providing all pipe connections and fixures, etc., including cost and conveyance of all materials and labour charges, including Overheads and Contractors Profit @13.615% etc., complete for finished item of work as per department approved designs and drawings but excluding GST and Seigniorage charges .

3500 KL Sump @ Head Works

Construction of OHSR with M30 grade design mix with required Fe 500 HYSD steel at the site selected by the Department, as per drawings and as specified in Technical Specification including earth work excavation in all types of soils for foundations including cost and conveyance of all materials, cost and fabrication of steel, fixtures, labour charges and testing the reservoir for water tightness etc., complete for finished item of work as per the Standard Specifications and as per the provisions made in the SoR 2026-27. The rate is inclusive of cost of all materials, vertical connections and labour charges etc., complete for finished item of work, including cost of DI pipes, DI Valves, etc, and excluding GST and Seigniorage charges, including Contractors Profit Overheads charges @13.615%. 1). All concrete members shall be designed with M30 grade design mix. 2) Rate is for OHSRs with RAFT FOUNDATION 3) Rate inclusive of three coats of epoxy paint Food Grade of best quality to inner surface of the Reservoir including bottom of roof. 4) Rate inclusive of 2 coats of whether proof emulsion painting for external surfaces, lettering, all required fixtures, pipes, bends, valves etc., for pipe connections including cost of pipes, bends and valves as per departmental designs and drawings. 5) The above rates are applicable for basic wind speed of 200 KMPH and SBC 15 T/sqm . Fixtures include : a) RCC or Aluminium ladder inside 0.60 m wide. b) Spiral staircase on the outside shall be provided upto 200 KL. c) Lightening arrestor, including conductor and earthling etc. d) RCC ventilators with copper or stainless steel fly proof mesh. e) D.I Manholes frame and cover 0.60x0.60m as per IS specifications (light duty) - 2 Nos. f)Water level indicator of good quality with ebonite/copper float of approved pattern-1 No. g) The railing provided to the gallery and staircase shall be with stainless steel of grade 304 for a height of 1.20m. i) D.I swan neck ventilators shall be provided in top dome and slab. j). Bed Blocks of 0.45m x 0.45m x 0.30m in CC M15 Mix below all the duck foot bends k) The rates are inclusive of CI verticals for all inlet, out let, overflow and scour connections( as per estimate diameters) and D.I valves. All valves near inlet, out let and for scour shall be D.I valves of heavy duty conforming to the specification of SoR item No.30

10 KL-12.45 M Stg

20 KL-12.45 M Stg

30 KL-12.50 M Stg

40 KL-12.90 M Stg

60 KL-12.95 M Stg

90 KL-12.90 M Stg

120 KL-13.15 M Stg

250 KL-13.45 M Stg

Construction of Pump houses of various sizes with RCC Framed Structure with RCC foundations with M20 grade mix with required Fe-500 HYSD Steel and its fabrication including earth work excavation for foundations, laying of PCC for levelling course below foundations, Superstructure with Brick Masonry in CM (1:6), required windows and ventilators and Rolling shutters, Plastering to the walls on both inside and outside, impervious coat over the roof slab, Painting two coats over primary coat with oil bound distemper inside and cement based snowcem painting outside, synthetic enamel painting to iron works, VCC Flooring and necessary drains with CI gratings and drain pit for drainage of spill over water, internal and external electrification works including cost and conveyance of all materials and labour charges including Overheads and Contractors Profit @13.615% etc., complete but excluding GST and Seigniorage charges for finished item of work as per department approved designs and drawings.

Pump House of size 3.00 x 4.00 m

Pump House of size 4.00 x 6.00 m

Pump House of size 12.00 x 6.00 m

Pump House of size 18.00 x 8.00 m

Construction of Rapid Gravity Filtration (RSF) Plant with M30 grade concrete including all civil, mechanical and electrical works using sand as filter media, compatible with SCADA arrangements, duly following relevant IS codes in the design of plant components including trial running for 90 days etc., including Chlorine contact tank & Consumables for 90 days, supply and installation of Lab equipment of reputed make for conducting all laboratory tests and consumables for one year including training to the Staff, as per the technical specifications, as per the details in the SoR 2026-27 and as directed by the department Engineer etc., complete for finished item of work for the following capacities of RSF Plants. The rate is inclusive of Overheads and Contractors Profit @13.615% but excluding GST and Seigniorage charges.

41 MLD Rapid Sand Gravity Filters

Construction of 25 m length and 15 m width RCC framed Intake well cum pump house with M30 grade design mix and Fe 500 HYSD steel for structures including cost and conveyance of all materials and labour charges, fabrication charges etc., complete including Overheads and Contractors Profit @13.615% but excluding GST and Seigniorage charges for finished item of work as per department tentative designs and drawings etc., complete at Hiramandalam Reservoir

Construction of Foot Path Bridge of length 500mts and width 7.5 mts with M30 grade design mix and Fe 500 HYSD steel for structures including cost and conveyance of all materials and labour charges, fabrication charges etc., complete including overheads and contractors profit @ 13.615% but excluding GST and seigniorage charges for finished item of work as per department tentative desings and drawings etc., complete at Hiramandalam Reservoir

Design, Manufacture, Supply, delivery, erection, testing and commisioning of pumping Machinery (ISI) with all accessories, appurtenances, surge protection devices, ultrasonic flowmeter on common delivery main at each pumping station, piping as per design requirement and as directed by the Department on turnkey basis including trial run. The rate is inclusive of engagaging required man power, operate and maintain the facilities during the trial run period. The scope of the work includes electrical switchgear panels, soft starters, capacitor banks to maintain required power factor, electrical equipment, connections including required cabling from pumps to the panel board, vaccume pumpsets required for priming with necessary piping such as suction pipes, delivery pipes, common manifold with necessary gate valves, non return valves etc., hoisting equipment such as monorail with chain pulley block (upto 200 HP Pump sets)/Gantry crane (above 200 HP pumpsets), fire safety equipment, ventilation system, electrical safety system including necessary cable trays and drainage arrangements for spill over water in the pump house, etc., complete for finished item of work as per the technical specifications and as directed by the department Engineer for the following Pumping Machinery capable of delivering water to the discharge and head mentioned below. Including overheads and contractors profit @ 13.615% and exclusive of GST. (For HT motor with 3.30 KV and 6.60 KV power supply shall be provided with Vaccum Circuit breakers, switch controls and soft starters). (For Vertical Turbine pumps-Variable Frequency drive shall be provided in panel board to cope up with head variation).

Vertical Turbine Pump Sets

340 HP VT - 3 No- 13450 LPM & 90 m Head

Horizontal Split Casing Pump sets/Centrifugal/Monoblock Pumpsets

400 HP HSC - 3 No- 12430 LPM & 110 m Head

15 HP HSC - 3 No- 530 LPM & 80 m Head

10 HP HSC - 3 No- 340 LPM & 70 m Head

5 HP HSC - 2 No- 10 LPM & 150 m Head

2 HP HSC - 2 No- 10 LPM & 50 m Head

2 HP HSC - 2 No- 20 LPM & 40 m Head

2 HP HSC - 2 No- 20 LPM & 50 m Head

2 HP HSC - 2 No- 10 LPM & 90 m Head

2 HP HSC - 2 No- 20 LPM & 50 m Head

2 HP HSC - 2 No- 10 LPM & 60 m Head

Supply and fixing of MS/Structural steel angle / channel / beam / bars/Flats including cost of materials, transportation with overheads & CP 13.615% etc., complete but excluding GST and other taxes.

Supply and fixing of MS Plates including cost of materials, transportation with overheads & CP etc., complete but excluding GST

Supply and fixing of Bolts and Nuts including cost of materials, transportation with overheads & CP etc., complete but excluding GST

Construction of RCC Pedestal of size 1.8*0.90*1.2 mts including required earthwork, CC (1:4:8) levelling course, RCC (1;1.5:3) for Raft, Footing, Pedestals with requires steel and its reinforcement charges etc., including cost and conveyance of all materials, labour charges etc., Complete with contractors profit & Over head charges 13.615% at canal crossings but excluding GST and other taxes.

Earthwork excavation and depositing on bank with an initial lead and lift in all types of soils including cost and conveyance of all materials and labour charges etc., complete

CC(1:4:8)using 40 mm HBG metal icluding Cost and conveyance of the all materials etc complete.

VRCC(1:1.5:3) using 20 mm HBG metal including cost and conveyance of all the materials,but excluding the cost of the steel etc complete

Supply and placing of the HYSD bars, fabrication including cost and conveyance of all materials and labour charges etc., complete

River crossing including earth work excavation, Obstruct / divert the water, Bailing of water, laying of PCC for levelling course, Pipe encasement with M30 grade mix with required Fe 500 HYSD Steel and its fabrication, and conveyance charges of machinery and other required materials, in co-ordination with the concerned authorities as per approved drawings and directed by the Engineer-in –Charge, including 13.615% over head and contractor profit charges but excluding GST etc complete.

Earthwork excavation and depositing on bank with an initial lead and lift in all types of soils including cost and conveyance of all materials and labour charges etc., complete

In ordinary soil below GL

Excavation, Loading, Unloading , transportation and soil filling for obstract and divert the water flow for river crossing

Plain Cement Concrete (1:4:8) for foundations and under flooring bed using 40mm size hard, machine crushed granite from approved quarry including cost and conveyance of all materials to site, including all charges for machine mixing, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc., and overheads & contractors profit complete for finished item of work.

Supply and placing of the M30 Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, centering, shuttering, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges for finished item of work. For Pipe Encasement.

Providing High Yield Strength Deformed (HYSD) steel bars (Fe 500 grade as per IS 1786-1979) of different diameters for RCC works , including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap-splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars, including all wastages such as overlaps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including soverhead charges & Contractors profit but exlcuding GST and other taxes on all materials etc., complete for finished item of works.