MPLADS Installation of high mast light at shastri road Kurian uthup road jn kottayam

Amount

Installation of high mast lights

90.15.2.2 Supply installation testing and commissioning of High Mast using Octogaonal Pole made single/two sections of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x16 mm suitable for wind speed as per IS 875 Part III with head frame assembly two point suspension system with steel wire ropw 5mm dia double drum winching system w and including round arm galvanized luminary carriage suitable to install 6/8 nos luminaries in symmetrical arrangement control gear box and lighting spikes with single phase operation power tool installed inside the base compartment including connector foundation bolt 4 nos fixed in existing RCC foundation and junction box etc, complete 10 meters

90.15.4.9 Supply Conveyance, installation , testing and commissioning of 150 W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled /Nichea with power factor greater than 0.95 at full load ,internal surge protection up to 8 Aluminium pressure die-cast Powder coated housing ,acrylic cover complete with THD less than 10%,power factor greater than 0.98 RoHS compliant , duly wired up for use on 230 V AC supply .Driver compartment should be seperatly accessible for maintenance (LM 79& 80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer.

90.15.4.8 Supply Conveyance, installation , testing and commissioning of 120 W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled /Nichea with power factor greater than 0.95 at full load ,internal surge protection up to 8 Aluminium pressure die-cast Powder coated housing ,acrylic cover complete with THD less than 10%,power factor greater than 0.98 RoHS compliant , duly wired up for use on 230 V AC supply .Driver compartment should be seperatly accessible for maintenance (LM 79& 80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer.

14.1 Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50 metres

14.9 Providing and laying in position cement 1:3:6(1 cement:3 coarse sand: 6 graded stone aggregate 40 mm nominal size ) in foundation of pump ,DG set etc. including form work etc as required

14.8 Providing and laying in position cement 1:3:6(1 cement:3 coarse sand: 6 graded stone aggregate 20 mm nominal size ) in foundation of pump ,DG set etc. including form work etc as required

14.12 Providing 15 mm thick cement plaster of mix 1:4(1 cemet :4 fine sand) at all levels.

OD142350/2021-2022 Reinforcement for R.C.C works,bend tied and placed in position (plain grill requiring bend cold) using tor steel as required

1.17.11 Supplying and drawing following sizes of FRLS PVC insulated copper conductor , single core cable in the existing surface /recessed steel/PVC conduit as required 2x2.5 sq.mm

90.6.5.11 Supply and drawing the following sizes of multi-core PVC insulated& FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface /recess conduit as required including giving necessary connections of the following sizes .3 core 1.5 sq.mm

90.12.10.2 Supply & laying of DWC pipe in ordinary soil 0.75 m below ground level including excavation 50/38mm or nearest size

90.12.5.2 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1 KV grade of the following sizes in the existing RCC /HUME/STONE WARE/GI/DWC pipe as required .2 core 6 sq mm

90.12.7.2 Supply, laying and clamping of 1 no. PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms,making good the damages, colour washing etc. as required .2 core 6 sq mm with factory made clamp.

9.1.1 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required .2 X 6 sq.mm(19mm)

1.17.20 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface /recessed steel/PVC conduit as required .2 X 4 sq.mm

2.10.1 Supplying and fixing 5 amps to 32 amps rating , 240/415 volts, "C" curve , miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections , testing and commissioning etc. as required .Single pole

2.10.2 Supplying and fixing 5 amps to 32 amps rating , 240/415 volts, "C" curve , miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections , testing and commissioning etc. as required .Single pole and neutral

2.12.1 Supplying and fixing following rating, double pole ,240 volts, isolator in the existing MCB DB complete with connections , testing and commissioning etc. as required .40 amps

2.14.1 Supplying and fixing following rating ,double pole,(single phase and neutral) ,240 volts residual current circuit breaker(RCCB) , having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections , testing and commissioning etc. as required .25 amps

5.4 Earthing with G.I earth plate 600mm X 600 mm X 6mm thick including accessories , and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal /coke and salt as required

5.15 Providing and fixing 25 mm X 5 mm G.I strip on surface or in recess for connections etc. as required

90.16.3.1 Supply and clamping the following size of strips on surface of wall/parapet /existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1m , making good the damages, colour washing etc, as required( for horizontal run )20 X 3 mm GI strip

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/cables and giving connection as required 3.15 mm(10 SWG)

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required 3.15 mm (10 SWG)

90.14.1.1 Fabrication ,supply , conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof , cubicle typle MV panel board comprising of the following components /devices & comlying to IS 8623 .Fabrication of fully partitioned , dust and vermi proof, cubicle type MV panel board comprising of the following components /devices & complying t IS 8623 .Fabrication of fully partitioned , dust and vermin proof enclosure for panel assembly as per IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirements , with front and rear access facility,bus bar chambers , hinged doors for all switch gear compartments,earthing the doors using 4 sq mm braided copper conductor , providing necessary cut-outs for mounting meters,relays indication lamps,bus bar interconnection etc,detachable covers for bus bar chamber and cable alley,powder coating the assembly after subjecting to 7 tank process etc as required.CRCA sheet alone be used for the fabrication .Angles/flats/slotted angles etc shall not be used for the fabrication of the panel assembly.The measurements will be taken the area of the complete sheets used for panel board including partitions ,folding,shrouding etc.Supply and fabrication of MV panel board using 2.00 mm CRDA sheet,powder coated(excluding base frame)

90.14.2.1 Supply and providing 2 mm SMC sheet as shrouding for bus interconnection / terminations etc.including required nut &bolt etc

90.14.3.2 Supply and providing heavy duty 'A' section neoprene gasket in the panel board U' section rubber beeding suitable for 1.60/2.00 mm sheet

OD142351/2021-2022 Supply and providing the following sizes of bolt and nut with washers on the existing MS bot /earth bus etc.as required including drilling necessary holes as required 12x3 mm brass bolt

OD142352/2021-2022 Supply and providing 25x 6mm brass nut and bolt etc. as required

OD142353/2021-2022 32A ,2 w neutral links mounted on DMC -SMC base

OD142354/2021-2022 Supply and fixing 32 A HRC fuse with HRC fuse link

OD142355/2021-2022 Supply and fixing Analog Time switch 240V AC DIN/BASE mounting (L&TAUTS03AN00- Analog version )in the existing enclosure and giving connection as required

OD142356/2021-2022 Supply and fixing 25A ACI, MNX 9,2 pole power contactor (L&amp ;T-make ) conforming to IS/IEC 60947-4-1 & IEC60947-4-1 in the existing enclosure and giving connection as required

OD142357/2021-2022 Supply and proving name bord on 16/20mm thick granite slab with inscriptions as directed,Fixing it on foundation with required material etc as requierd

OD142358/2021-2022 Supply and fabrication conveyance and installation of angle iron frame work for mounting outdoor unit/indoor units using suitable size MS angle/flats cut and welded to shaped fixing the same on floor or wall/parapet asrequired including painting with 2 coats of enamel paint over a coat of zinc chromite primer&mdash

OD142359/2021-2022 Amount to be deposited with KSEB for availing service connection (actual amount will be reimbursed on production of original documents)

AJITH

Anandan K

PBS Switchgears and Automation Pvt Ltd

Bidder Name

AJITH

MERKURY ELECTRICAL CORPORATION

PBS Switchgears and Automation Pvt Ltd

Anandan K