Development of Ind. Area Chanour Distt. Kangra (HP). (SH- C/o Pump House and attendant room).

Amount

Excavation in foundation trenches etc.in all classification of soil in dry or saturated condition upto any depth and lift including pumping and bailing out water where required i/c stacking the seviceable material and un- servicxeale material separate as directed and then returning the stacked soil in 15 cm layers when required into plinth and sides of foundation etc. consolidating each deposited layer by ramming,watering, dewatering and then disposing of all surplus excavated earth as directed by Engineer in chanrge including carriage of material in all leads and lifts disposed material to be neatly dressed leveled as per instructions of the Engineer in charge.

Providing and laying cement concrete 1:5:10 (1cement: 5sand: 10 graded crushed stone aggregate 40mm nominal size) and curing complete including cost of form work in foundation and plinth including carriage of material within all leads and lifts.

Brick work using common clay burnt building bricks in foundation in cement mortar 1:6 (1 cement :6 sand) 1st class bricks including carriage of material within all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angles iron in frame 30x30x5mm so as to give a fair finish including centring,shuttering strutting and propping etc. wooden batten and ballies for all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu reinforcement and plain concrete including carriage of material within all leads and lifts in:- (a)Beams,cantilever, girders and lintels sides and soffits of beams,beam haunchings, cantilever,girders, bressumers and lintels not exceeding 1mtr. In depth

(b) Flat surfaces such as soffits or suspended floors, roofs,landings and the like floor etc.upto 200mm in thickness.

© Foundation, footings basis of columns etc. and mass concrete.

(d) Columns, pillars, posts and struts Square, rectangular or polygonal in plan.

Providing and laying cement concrete work 1:1.5:3(1cement: 1.5sand:3graded crushed stone agg.20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of material within all leads and lifts in- (a) Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto all heights

Providing TOR steel reinforcement for RCC work including bending binding and placing in position in all heights including carriage of material within all leads and lifts.

Boulder filling broken hand packed Under Floors

Brick work using common clay burnt building bricks in super structure above plinth level upto all heights with in cement mortar 1:6 (1 cement :6 sand) Ist class bricks including carriage of material within all leads and lifts.

Half brick masonry in common burnt clay building bricks in Cement Mortar 1:4 (1 cement : 4 sand) First Class Bricks

6mm cement plaster to ceiling in cement mortar 1:4 (1cement :4sand) including carriage of material within all leads and lifts.

15mm cement plaster in single cost on rough side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rouded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement:6sand) including carriage of material within all leads and lifts.

15mm cement plaster in single coat on fair side of brick/ concrete/ stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rouded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement:6sand) including carriage of material within all leads and lifts.

Applying Birla white wall care putty two coats over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material within all leads and lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of material within all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of material within all leads and lifts.

Providing and fixing glass strips in joints of terrazzo floors. 40 mm wide and 4 mm thick.

Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm nominal size)laid in one layer finished with a floating coat of neat Cement. 40 mm thick.

Digital tiles 6 mm thick of size 30x60 cm in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry including carriage of material within all leads and lifts.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint. In gratings framed guard bars, ladders, railling, brackets and similar works.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size) under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material within all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including fitting the joints with approved adhesive complete. 110mm dia pipes including carriage of material within all leads and lifts.

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. Pipes embedded in and including cement concrete blocks 10x10x10cm 1:2:4mix ( 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) and cost of cutting holes and making good the wall etc. 110mm dia including carriage of material within all leads and lifts.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete PVC Plain bend 110mm dia including carriage of material within all leads and lifts.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws 35mm thick 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. 30 mm thick 2nd class deodar wood including carriage of material within all leads and lifts.

Providing and fixing oxidized M.S. sliding door bolts with nuts and screws etc. complete.: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 250x16 mm

Providing and fixing anodized aluminium tower bolt (barrel type) anodized transparent or dyed to required shade and colour with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. ( a). 200x10mm (Two Hundred into Ten milimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (i) 150mm including carriage of material within all leads and lifts.

Providing and fixing bright finished hard drawn hooks and eyes. 150mm

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. Plain grill including carriage of material within all leads and lifts.

P/F 12 mm thick prelaminated board both side bwp phenol bonded exterior/interior grade shutters withframe of 1st class deodar wood for cup board including nickel plated bright finished piano hinges -25mm thick frame.

Providing and fixing 1 mm thick M.S sheet garrage door with frame of 40 mm x 40mm x 6mm angle iron 3.15 mm m.s gusset plates at the junctions and corners,all necessary fittings complete including applying a priming coat of red lead paint. Using Flats 30 mm x 6 mm for diagonal braces and central cross pieces

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting.Readymixed paint brushing wood primer pink including carriage of material within all leads and lifts.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white including carriage of material within all leads and lifts.

Painting two coats(excluding priming coat)on steel and other metal surfaces with enamel paint,brushing to give an even shade including cleaning the surface of all dirt,dust and other foreign matter.Enamel paint other than white.

Excavation in earth work and filling in 15cm layers i/c watering ramming and consolidating complete.

Cement concrete 1:3:6(1cement:3sand:6graded stone aggregate 20mm nominal size) and curring complete inculding cost of form work in foundation and plinth.

Providing and fixing to wall ceilling and floor galvainised mild steeel tubes(medium grade)tube fittings and clamps including making good the wall including carriage of material within all leads and lifts. (a) 15 mm nominal bore.

(b) 20 mm nominal bore.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked 4.5kg/sqm pressure including fixing with approved adhesive etc. complete 110mm nominal size including carriage of material within all leads and lifts.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete. (i) 110mm nominal size. .

(ii) Plain bend 110 mm nominal size.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm.

Providing and fixing Vitreous china wash down, water closet ( European type W.C pan) with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1(1 Cement :1 Sand ) ( Seat and over to be measured and paid for separately) including carriage of material within all leads and lifts. a) ordinary closet

Providing and fixing 100mm size P or S trap for Water closet (squatting pan) including jointing the trap with the pan & soil pipe in C. mortar 1:1 (1cement : 1sand) vitreous china including carriage of material within within all leads and lifts.

Providing and fixing 10.00/12.50/15.00 ltrs PVC low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet

Providing and fixing GI inlet connection for flush pipe with WC pan including carriage of material within all leads and lifts.

a) Providing and fixing vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings.Flat back630x450mm including carriage of material within all leads and lifts.

b) Providing and fixing viterous china pedestal for wash basin complete recessed at the back for the reception of pipes and fittings.

Providing and fixing CP brass waste for wash basin or sink 32 mm dia including carriage of material within all leads and lifts

Providing and fixing 100m sand cast iron grating for gully,foor or Nahani trap including carriage of material within all leads and lifts..

Providing and fixing 600x450mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or plywood sheet and fixed to wooden plugs with CP brass screw and washers including carriage of material within all leads and lifts.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden pluges with CP brass screws 600x20mm including carriage of material within all leads and lifts.

Providing and fixing CP brass bib tap with capastan head 15 mm dia. (Jagour Make) including carriage of material within all leads and lifts.

Providing and fixing CP brass pillar tap with capstan head 15 mm dia (Jagour Make) including carriage of material within all leads and lifts.

Providing and fixing CP stop cock 15mm dia.(Jagour Make) including carriage of material within all leads and lifts.

Providing and fixing CP connection pipe with brass unions 30 cms length 15mm nominal size including carriage of material within all leads and lifts.

Providing and fixing brass full way valve with wheel including carriage of material within all leads and lifts.(1) 15mm nominal bore with Minimum Weight of 300 Gm.

II) 20mm nominal bore with Minimum Weight of 550Gm

Providing and fixing GI or MI union including carriage of material within all leads and lifts. (1)15mm nominal size

II) 20mm Nominal size

Providing and fixing charomium plated brass soap dish with C.P.brass brackets fixed to wooden cleats with C.P. brass screws including carriage of material within all leads and lifts.

Providing laying (to level and slopes) and jointing reinforced concrete light duty non pressure pipe IS class NP-2 of following internal diameter with collar joints including testing of joints completes. 150 mm dia including carriage of material within all leads and lifts.

Constructing man hole with RCC top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testing: Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg. (Weight of cover 23 kg and weight of frame 15 kg.)(a) With 230mm thick walls of brick masonary using common brunt clay building bricks in cement mortar 1:3 (1 cement :3 sand).

Providing and fixing Zet connection complete in all respcet 15 mm Dia including carriage of material within all leads and lifts.

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting. 610 x460 mm with bowl depth 200 mm

Providing and Laying of Interlocking Concrete Block Pavements ISI Mark having thickness 60 mm as per drawing and Technical Specification Clause 1504

Rahul Sharma

Lovish Bhardwaj

Dhian Singh

Nitish Thakur

ILLUMINATE MANAGEMENT AND GLOBAL SERVICES PVT LTD