REPAIR MAINT OFFICES AREA,OFICCER ACCN,MESS AREA,MT AREA AND REPAIR TO JOINERY ,PLASTERING,FLOORING AND SANITARY FITTING AT PATTAN UNDER GE 969 EWS.

Amount

Demoliton of cement concrete (un-reiforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-charge.

Dismantling floor hearh wall tile incl cement mortar bedding, removing serviceable tiles to store and rubbish of f the permishes complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or frames but with shutters (without taking off shutters from the frame) exc 1.5 Sqm and n.exc 4.00 sqm complete all as specified and directed by Engineer-in-charge.

Taking down chowkats or frames not exceed 1.5 Sqm complete all as specified and directed by Engineer-in-charge.

Demolition of brick work, PCC block masonary, stone masonary or boulder masonry built in cement mortar complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster or screed bedding layer of any description from concrete slab/terrace surfaces etc including racking out joints hacking for key, scrubbing down with water etc.complete all as specified and directed by Engineer-in-charge.

Dismantling timber scantlings in fillets, rails,posts rafters,purlins etc under 40 sqcm in section unframed work complete all as specified and directed by Engineer-in-charge.

Dismantling timber scantlings 40 sqcm and over in section in any position unframed work complete all as specified and directed by Engineer-in-charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or simialr pattern roof covering complete all as specified and directed by Engineer-in-charge.

Dismantling of wall and celling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness inlcuding cover fillets complete all as specified and directed by Engineer-in-charge.

M&L for 25 mm thick PCC type B-0,1:2:4 using 12.5 mm graded aggregate as in flooring finished even and fair w/o using extra cement complete all as specified and directed by Engineer-in-charge.

M& L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded aggregate as in plinth protection finished even and smooth w/o using extra cement complete all as specified and directed by Engineer-in-charge.

M & L Cement concrete in foundations, filling and mass concrete1:4:8 type D-2 using 40 mm graded aggregate 75 mm thick complete all as specified and directed by Engineer-in-charge.

M & L for non skid coloured printed ceramic tile 7 to 8 mm thick ( Square/rectangular/in joint less) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm,in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colur of tiles over 15 mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M & L for non skid coloured printed ceramic tile 7 to 8 mm thick ( Square/rectangular/in joint less) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm,in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colur of tiles over 15 mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M & L for glazed ceramic tiles in vertical surface 600x300x10 mm thick colour and design (as approved) in vertical surface and jointed in neat cement slurry and pointed in whiter or colour cement to match the colour of tiles over 10 mm thick cement plaster using CM (1:4) complete all as specified and directed by Engineer-in-charge.

M & L for vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M& L Machine pressed rubber moulded coloured precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pegment complete all as specified and directed by Engineer-in-charge.

M & L for brick work with sub class 'B' bricks (old sizes) straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer-in-charge.

M & L For Rendering 15 mm thick plastering on brick work or concrete surface in CM (1:6) and rendering is to be finished even and smooth w/o using extra cement complete all as specified and directed by Engineer-in-charge.

S&F in repair pre-painted corrugated galvalume aluminium zinc coataing GI based profile steel sheet 0.50 mm thick of any colour having tnsile strength of 550 MPA as in roof covering/cladding to wall,fixed with self tappping screw complete all as specified and directed by Engineer-in-charge.

All as item no 24 but except sheeting removing and refixing in repair complete all as specified and directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-charge.

M&L in repair galvanised,corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap, fixed with coach screw and washers in roofs, walls etc complete all as specified and directed by Engineer-in-charge.

S&F in repair plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings(length and girth as fixed) with grade of zinc coating 120 gm complete all as specified and directed by Engineer-in-charge.

M&L for plain fillets square rectangular or triangular in section using 2nd class soft wood clean swan secured with nails exc 13 but n. exc 25 sqcm in section complete all as specified and directed by Engineer-in-charge.

S&F in repair 2nd class softwood in scantling clean swan timber framed and fixed to the position to replace old and decayed timber complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous chine wash basin, white flat back size 550x400 mm plug, porcelain stopper and incl braxkets with waste fittings and connection pipe etc complete all as specified and directed by Engineer-in-charge.

S&F in repairs pillar taps, 15 mm dia cast copper alloy fency type with capstan heads, chromium plated. screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts screwed for iron pipe complete all as specified and directed by Engineer-in-charge.

S&F for 15 mm bore in repair bib taps, fancy type chormium plated with crutch or butterfly handle scered down sced for iron pope or for brass ferrul and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair stop valves brass screwed down high presure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions 15 mm bore and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC (SWR) pipes 110 mm single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed by Engineer-in-charge.

S&F in PVC (SWR) junction single T equal or unequal 110 mm dia complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) bends 110 mm dia fixed complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC flushing cistern, 10 ltrs capacity, low level including brackets, inlet and outlet PVC pipe and fittings complete all as specified and directed by Engineer-in-charge.

S&F vitreous chine wash down water closet pan ( Pedestal pattern) white or coloured excluding flushing cistern and flush pipe and seat cover incl provision of concrete/ white cementing and P or S trap in repairs.

S&F PVC connection pipe 15 mm size with PTMT nuts of length 600mm fixed to GI tubbing complete all as specified and directed by Engineer-in-charge.

Taking down and replacement with 20 mm 3-layer PP-R polypropylele random copolymer) concealed pipe SDR 7.4 (PN-16) UV stabilized and antimicrobial fusion welded having thermal stability for hot and cold water supply including all PRR plain & brass threaded polypropylele random fittings fixed complete to walls, ceiling or in floors ,complete all as specified and directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engineer-in-charge.

S&F Sheet glass thickness 3.00 mm,ordinary quality and glazing with oil putty in square exceed 0.5 sqm in each pane including in repairs complete all as specified and directed by Engineer-in-charge.

S&F in repair brass chromium plated tubular towel rail 20 mm dia D type , 60 mm long between flages complete all as specified and directed by Engineer-in-charge.

S&F in repairs Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by Engineer-in-charge.

Preparation of old undecorated surfaces of walls and applying one coat of oil emulsion complete all as specified and directed by Engineer-in-charge.

Preparation of old undecorated surfaces of walls and applying one coat of white wash complete all as specified and directed by Engineer-in-charge.

S & F Brass CP central hole basin mixer 15 mm for mixing hot & cold water screwed down for iron pipeand fixed complete all as specified and directed by Engineer-in-charge.

S&F Door closer hydraulically regulated cost iron body designation No 1 universasl type suitable for door shuutters up to 700 mm in width and of weeight not more than 35 kgs in repairs complete all as specified and directed by Engineer-in-charge.

S&F sheet glass shelf assembly consisting of 5.5 mm sheet glass shelf 12 cm wide with brass chromium plated bracket guard and 60 cm long complete all as specified

S&F corner sheet glass shelf assembly consisting of 5.5 mm sheet glass shelf 12 cm wide with brass chromium plated bracket guardcomplete all as specified and directed by Engineer-in-charge.

S&F 6 mm thick insulation consisting of PVC Insulated Panels as in wall having expanded(Rounded moulded) polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing Note : Panelling should be rested on L/U shape edge profile of same pattern (PVC/Aluminium) complete all as specified and directed by Engineer-in-charge.

M&L 4 mm thick Plywood, grade BWR,type BB, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-charge.

S&F 6 mm thick insulation consisting of PVC Insulated Panels as in ceiling having expanded polystyrene (Rounded moulded) polystrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing Note : Panelling should be rested on L/U shape edge profile of same pattern of panelling (PVC/Aluminium)

S&F angle valves 15 mm, cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated in repair complete all as specified and directed by Engineer-in-charge.

S & F Brass CP wall mixer 15 mm for mixing hot & cold water screwed down for iron pipeand fixed complete all as specified and directed by Engineer-in-charge.

S &F in repair curtain rod, mild steel, chromium plated fixing with stainless steel brackets and funnels stops, rollers etc complete all as specified and directed by Engineer-in-charge.

S&F Rat tail (helical) door spring 300 mm long welded to steel chowkat in repairs complete all as specified and directed by Engineer-in-charge.

S&F in reapair CP brass health flucet hand held triggered nozzle and delivers a spray of water with pipe complete all as specified and directed by Engineer-in-charge.

S&F in reapair CP jet spray with flexible tube 1.5 mtr long complete all as specified and directed by Engineer-in-charge.

S&F 2nd class soft wood 12 mm thick and 100 mm wide plane one side with edges tounged and groove joint as in wall panelling fixed with nail complete all as specified and directed by engineer-in-charge.

S&F 2nd class soft wood 12 mm thick and 100 mm wide plane one side with edges tounged and groove joint as in ceiling panelling complete all as specified and directed by Engineer-in-charge.

M&L for french polishing on surfaces of any descreption, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with one or more coats complete all as specified and directed by Engineer-in-charge.

M&L for plain fillets square rectangular or triangular in section using 2nd class soft wood clean swan secured with nails not exc 3 sqcm in section complete all as specified and directed by Engineer-in-charge.

M&L for plain fillets square rectangular or triangular in section using 2nd class soft wood clean swan secured with nails exc 3 but not exc 6 sqcm in section complete all as specified and directed by Engineer-in-charge.

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 630 x 450 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-charge.

S&F 2nd class soft wood glazed and skeleton shutters 35 mm thick , open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer-in-charge.

S&F Plain, framed,panelled shutters thickness 35 mm of 2nd class softwood,(any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed by Engineer-in-charge.

S&F Glazed and skeleton shutters thickness 30 mm,(2nd class softwood), open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters supplied and fitted to chowkats if windows, ventilators, etc. are provided with stiles and rails as in SSR Part I, Sectionspecified 8 clause 8.24(b) complete all as specified and directed by Engineer-in-charge.

S&F 2nd class soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer-in-charge.

M&L for two coats of synthetic enamel paint over a coat of pink primer including preparation of surface on wooden sruface over 10 cm width or girth complete as specified complete all as specified and directed by Engineer-in-charge.

Aluminium anodised, barrel tower bolts 100 mm of extruded section and fixed complete all as specified and directed by Engineer-in-charge.

Aluminium anodised, barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed by Engineer-in-charge.

Aluminium alloy, anodised, sliding door bolt 200 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer-in-charge.

M S Butt hinges 100 mm medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engineer-in-charge.

M S Butt hinges 75 mm medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engineer-in-charge.

Aluminium handles 100 mm , cast type,anodised complete all as specified and directed by Engineer-in-charge.

Aluminium handles 150 mm , cast type,anodised complete all as specified and directed by Engineer-in-charge.

S&F 15 mm Brass central hole CP wall mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair stop valves fancy tupe chromium plated screwed down high presure , with crutch or butterfly handle, cscrewed both ends for iron pipe or for unions 15 mm bore complete all as specified and directed by Engineer-in-charge.

S&F in PVC (SWR) junction single T equal or unequal 75 mm dia complete all as specified and directed by Engineer-in-charge.

S&F PVC (SWR) bends 75 mm dia fixed complete complete all as specified and directed by Engineer-in-charge.

S&F Durapaved chequered tiles (vitrified) 30 cm x30 cm x 8 to 10 mm thick set ,jointed and pointed in neat cement slurry in floors over 20 mm thick screed bed in CM (1:6) finished with cloured cement to match the shed of the slab complete all as specified and directed by Engineer-in-charge.

S&F Vitreous China Wall Hung coupled closet(one Piece) including cistern with lid dual flush fitting with PVC seat cover size not less than 665x360x765 mm (white) including fixing bolt complete all as specified and directed by Engineer-in-charge.

Javeed And Co

M/S MANZOOR AHMAD YATOO

M/S MUKHTAR CONSTRUCTION CO

M/S GHULAM NABI KHUROO AND CO

M/s GHULAM HASSAN MALIK

MS DUTTA BUILDERS