REPAIR TO COMPOUND WALL WALKING PLAZA BOUNDARY WALL JAFRY WALL ETC IN CERTAIN LOC AT SOUTH OF RLY LINE UNDER GE MISSAMARI

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for PCC (1:4:8) type-D2 with using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L brick work with sub class 'B' bricks, old size bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L brick work with sub class 'B' bricks, old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster on wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and as directed.

M&L Providing precast cement concrete louvres and jallies, 35mm thick (measured solid), including all mouldings in cement conctete Type B0 1:2:4 (12.5mm graded aggregate) and set in cement mortar 1:4 complete all as specified and directed.

M&L providing plain cement concrete type B0 (1:2:4), (using 12.5 mm graded stone aggregate), as in copings, bed plates and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

M&L 15mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 5mm) mixed with and including liquid water proofing compound in top layer as per manufacturer's instructions, finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 litre/ 10 sqm complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any positioncomplete all as specified and directed.

M&L Reinforced cement concrete ( Nominal mix) Type A1, 1:11/2:3 (20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L Reinforced cement concrete ( Nominal mix) Type A1, 1:11/2:3 (20mm graded aggregate) as in Columns, pillars, piers, posts and struts concrete complete all as specified and as directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, etc. flat, roughed finished surfaces, complete all as specified and as directed.

M&L Formwork to sides of pillars,posts, struts, piers, columns and stanchions. Square,rectangular or polygonal, roughed finished surfaces, complete all as specified and as directed.

M&L TMT bar 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.including 20mm thick backing layer in cement mortar 1:6 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

M&L 100mm thick cement concrete type D-2 (1:4:8) using 40 mm graded stone aggregate as sub base of floor finished even and fair complete all as specified and directed.

M&L 75mm thick cement concrete (1:3:6) type C-2( using 40mm graded crushed stone aggregate) as in pavement/hard standing laid in alternate bays (not exceeding 2 Sqm each) and finished even and fair without using extra cement complete all as specified and directed.

M&L Heavy duty coloured vitrified tiles 300x 300x10mm thick set and jointed in neat cement slurry & pointed in white or colour cement to match set and jointed in neat cement slurry and pointed in white or coloured including 15mm thick Screed bed or bedding layer of cement mortar 1:6, for laying floor finishes, including dismantling existing unservicaeable floor tiling with cement mortar bedding and removing rubbish/debris off the premises complete all as specified and directed.

M&L Pre polished chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick set and jointed and pointed in neat cement slurry in floor with grey cement and pigment over cement screed 15 mm thick in cement mortar 1:6 including dismantling existing unservicaeable floor tiling with cement mortar bedding and removing rubbish/debris off the premises complete all as specified and directed.

M&L precast cement concrete Type B1 1:2:4 (20mm grraded aggregate) set in cement mortar 1:6., in window or door cills, lintels,bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match complete all as specified and as directed.

M&L precast cement concrete 1:2:4 (using 20mm graded stone aggregate) type B1 as in landings, cover slabs(for man holes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and as directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any cement mortar complete all as specified and as directed.

S&F 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete. complete all as specified and as directed.

S&F at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, embedded in concrete , brickwork, masonary etc. including taking out embedded portion and making good disturbed ground, complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed.

Excavating in post holes (or similar holes) in soft/loose soil, each n exc 0.5 cu. m, getting out,and removing soil out of the site ,complete all as specified and as directed.

M&L providing plain cement concrete type C-2, (1:3:6), (using 40 mm graded stone aggregate), Cement concrete in foundations, filling and mass concrete complete all as specified and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concreteand screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 including necessary prepration of surface and applying a coat of red oxide zinc chrome primercomplete all as specified and directed.

Supply only chain link MS galvanized fencing 4mm dia and size as ordered, complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

S&F in repair Concertina coil 610mm dia, precoated with black anti-corrosive paint (weight 8Kg per coil expandable 6-8 mtr strech), short barb length 11+ 1mm thickness of tape 0.5mm, dia of spring core wire 2.6mm fixed on angle iron frames including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pin etc complete all as directed.

M&L TMT bar 10 mm dia and over, cut to length, bent to shape required, including cranking, hooking ends as in chain link fencing complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for. complete all as specified and directed.

S&F mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe.290.Gde-E-165 including necessary preperation of surfaces and applying one shop coat of red oxide, zinc chrome primer, complete all as specified and as directed.

M&L preparation new iron and steel surfaces of any description, exc 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L preparation new iron and steel surfaces of any description, not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L Hardcore of gauge n exc. 63 mm, Broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface,complete all as specified and directed.

Excavation in trenches n.exc. 1.5 m width and n.exc. 1.5 m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out, pipe etc in soft/loose soil & getting out, complete all as directed.

Returning filling in, including spreading, levelling, watering & well ramming in layers not exc 25 cm, complete all as specified and directed.

Removing excavated material (soils) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

S&F in repair, 2mm thick coloured Polycarbonate corrugated sheeting as in roof covering fixed with self tapping screws complete all as directed.

S&F in repair 18mm thick jalli factory made 100% solid WPC (Wood polimer composite) jalli of required of virigin PVC resin of K value 5o-60(Suspension grade) calcium carbonate and natural fibre (wood powders/rise husk/wheat husk) and non toxic addhesive, made from extrusion process WPC foam single extr having minimum density not less than 650 Kg/cbm, having good screw holding capacity(Screw withdrawl strength of 2000N(Face) & 1100N(Edge), minimum compressive strength of 50N/Sqmm, modulus of elasticity 850N/Sqmm and resistance of spread of flame of class A cateegory with property of being termite/Borer free.Water/moisture proof and fire retardant. WPC jalli to be fixed with stainless steel butt hinges of required size (if required) with necessary full body thread star headed counter sunk SS Screws complete all as per manufacturers instruction and as directed. Note:- Purchase voucher along MTC shall be submitted before commencement of work

DHEERAJ CONSTRUCTION (BID ID -3405176)

M/S YAIPHABA ENTERPRISES (BID ID -3402011)

Saraswati Auto Works (BID ID -3405077)

M/S S.S.Corporation (BID ID -3403249)

SUNIL KUMAR VERMA (BID ID -3403177)

M/S RANA ENGINEERING ENTERPRISE (BID ID -3397311)

Satya Enterprises (BID ID -3404743)

M/S B.B. Singh Contractor (BID ID -3404615)

Shree Krishna Traders (BID ID -3405567)

M/S TANISHQ CONSTRUCTIONS (BID ID -3405297)

MS Awash Ghosh and Brothers (BID ID -3405351)