SPECIAL REPAIR TO BLDG NO T-107 AND P-105 (HANGAR) OF ARMY AVN SQN, PROVN OF ARTIFICIAL RECHARGE FOR RAIN WATER HAEVESTING NEAR BLDG NO P-76 AND NEAR MEPTA AT MISSAMARI UNDER GE MISSAMARI

Amount

Dismantling plain or corrugated steel sheeting any gauge, thickness

S&F pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in ridge fixed with self tapping screws as specified.

S&F Fibre glass reinforced translucent corrugated sheeting 2 mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc fixed with L or J hooks complete all as specified and as directed

S&F Plain, black, mild steel sheeting 1.25 mm thick , in ridges,hips, valley gutters,drip and straight flashings length and girth as fixed complete all as specified and as directed

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth course/sub base as directed by engineer in charge.

M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation and mass concrete.

S & F in repair 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed in walls.

Dismantlinig wrought iron or mild steel work of any description not otherwise proveded for.

S&F roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam tee, angle, channel or flat sections) including clits etc conforming to Fe-410-0 W Gde- E- 250, Quality -A.

S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.conforming to Fe-410-0 W Gde- E- 250, Quality -A.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames)

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame)

S&F powder coated aluminium frame for doors, windows, ventileters, partitions with one or more rebates including joining cleat for fixing etc complete all as specified incl powder coating above aluminium section.(minimum thickness of powder coating 50 micron).

S&F powder coated aluminium door shutters aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips rubber neoprene packing anodised aluminium snap beading screws, locking arrangements, hinges, suitable handle etc complete all as specified powder coating of any colour(thickness of powder coating not less than 50 micron.

S&F for powder coated aluminium window shutters, side hung type without sash bars aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips,ruber neoprene packing,anodised aluminium snap beading screws,anodised aluminium fittings such as peg stays 150 mm long(1 no),hinges type-B-21 100 mm long( 2 no) suitable handle 1 no complete all as specified incl power coating of any colour (thickness of powder coating not less than 50 micron).

S & F aluminium body door closer hydraucally regulated, designation No. 3 universal type , suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg

S&F 4 mm thick Sheet glass, ordinary quality and glazing with wooden beads in squares not exceeding 0.5 Sq. M in each pane

S&F 5.5 mm thick Sheet glass, ordinary quality and glazing with wooden beads in squares exceeding 0.50 Sqm in each pane

For Surface Preparation: Surface Preparation by removing existing flooring with mechanical means, prepare the concrete substrate with proper scarifying & diamond grinding, Shot blasting, with Vaccum cleaning to remove dirt, dust, laitance, other contaminants etc., and to form the required anchor profile on the floor substrate between the floor topping and the concrete floor

For Floor Leveling (3mm thick) Providing and applying 2 part water dispersed epoxy resin primer Sikafloor ®-80 Epocem Primer or equivalent make like Fosroc/BASF/STP/Asian/Berger etc. followed by applying temporary moisturer barrier technology based three part, self smoothing underlay screed Sikafloor 81 Epocem or equivalent make like Fosroc/BASF/STP/Asian/Berger etc. to a thickness of 2mm having carbon dioxide diffusion coefficient 1782 as per Klopfer Engel fried method, Water vapour diffusion co-efficient µH2O = 177 as per DIN 52615, Water absorption co-efficient W = 0.06 kg/m2as per SN EN 1062-3, Compressive strength 55 N/ Sqmm after 28days as per ASTM C 579, Flexural strength 10 N/ Sqmm after 28days as per EN 196, When applied at minimum 3 mm thickness it can be laid over high moisture content substrate when substrate moisture is more than 4%.

For Installation of Epoxy topping 2mm using notch trowels and Spike rollers Providing and applying 2mm thick two part, solvent free, coloured,100% solids, self smoothing, smooth glossy, epoxy resin topping Sikafloor®-264 HC or equivalent make like Fosroc/BASF/STP/Asian/Berger etc. using notch trowels and spike rollers having compressive strength of 53 N/mm2 as per EN 196-1, Flexural strength of 20N/mm2 as per 196-1, Shore D Hardness 76 As per DIN 53 505, abrasion resistance 41mg ( CS10/ 1000/ 1000) as per DIN 53109. All in complete as per the manufacturers specifications and directions of the engineer in charge.

For Crack Treatment : Inspecting the surface for any cracks. Cracks if any have to be sealed with epoxy repair mortar after clean or removal of cover concrete and making 'V' groove of 20mm wide and 10mm deep cover crack line along the length of the crack by elctrically operated angle grinder with diamond concrete saw blade and cleaning it by air blower as directed by Engineer-in-Charge.

Sealing of exposed 'V' groove of 20mm wide and 10mm deep with Sikadur 31 or equivalent make like Fosroc/BASF/STP/Asian/Berger etc. solvent-free, moisture tolerant, thixotropic, structural adhesive and repair mortar, based on epoxy resins and special fillers, designed for use at temperatures between +10°C and +40 °C. Product should conforms to ASTM C 881-78, Type I, Grade 3, Class B+C : compressive strength > 60 N/mm2 (14 days) according to ASTM C881 : bond strength < 10 N/mm2 (7 days) according to ASTM C882 .

S&F in repair nylon HDPE bird proofing net of 2.5 x 2.5 cm of 1 mm thickness fixed with polypropelene rope of 6 mm dia for net and 12 mm dia for boarder with nail clips, cable zip ties & C hooks as directed by engr-in charge. Note : Rate quoted by the contractor shall deemed to inclusive of necessary scaffolding and all other fittings and binding materials as required for fixing the net complete all as directed.

Supply and fix for Turbo Ventilators Industrial/domestic turbo ventilator as per Manufactureres Insturction :- (i) (Turbine Dia 28 Inch (760mm), (Nech/Throat-24"), (Height-18"/610mm) (Vanes(Blades) - 42 Vanes, Aluminium 0.50mm Alloy 8011), Base Ring MOC(Mounting ring - Stainless steel),(Top plate MOC- Stainless steel 0.80 mm thickness). (ii) Rotation - Twin sealed 6203ZZ bearing with self lubricating duponty zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity Twin sealed 6201ZZ bearings with self lubricating Duponty Zytel 101L Polyamide 66 resin to ensure frictionless rotation even at lowest wind velocity. (iii) (Centre shaft : 18mm high carbon steel zinc plated) ( Inner Arms - M.S. with electro zinc plating), (Outer Arms - M.S. with electro zinc plating), (Frp base plate - 2mm thick clear 1.020 mtr wide 1.65 mtr long matching your sheet profile weight 8Kg Approx), (Centre width - 800mm+/-5mm), (Dia of Bottom Ring- 600mm+/-15mm), (Nos of Bearings -02 Nos), (Bearing Type : skf-6001ZZ & 6003ZZ) (Rivets-Aluminium Alloy wiht Washer) ,angle adjustable range- 0 to 17 deg,Exhaust capacity- 1972 - 2164 CFM, Wind velocity 8 Km/Hr, Make:- Tubro Ventilator India (Industrial Ventilating Solutions) or Equivalent as approved by GE complete all as specified and as directed.

Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed.

M&L for complete removal of old surfaces of walls and applying two coats of acrylic distemper including one coat of chalk whiting on plastered/putty surface to prepara-tory to distempering complete all as specified and directed over 1 mm thick wall care putty.

M & L for Complete removal of old surface for preparation of new wall surface applying Two or more coats of 100% Premium acrylic exterior emulsion paint with silicone additives of required shade additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @2.20 litre/ 10 sqm complete all as specified and directed.

Preparation of new or previously treated steel surfaces of any description, over 10 cm width or girth, not otherwise described appling one coat of Red Oxide, zinc chorme and applying two coat of synthetic enamel paint.

M&L two coats of Aliphatic two component paint suitable for concrete and plaster surfaces, especially in exterior application incl preparation of surfaces and as per manufacturer instruction complete all as specified and directed. Make - STP or equivalent.

Supply and fix in repair MS wheels of any size for hanger doors incl greasing complete all as specified and directed

Demolition of stone slabs tiles of any description or thickness in floors aprons laid bedded and pointed in any morter etc

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil compete all as specidied and directed.

Excavating over areas for each additional 1.5 m or part thereof in depth beyond the first 1.5 m getting out in soft/loose soil compete all as specidied and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base soft/loose soil compete all as specidied and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., additional 1.5 m or part thereof in height above the first 1.5 m high from base soft/loose soil compete all as specidied and directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (with modular size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement Mortar 1:3 complete all as specified and as directed.

M&L Brick Work with old size Sub-Class ‘B’ Bricks, laid on Edge as Side Walls of Brick Drains in Slope, Bedded and Jointed in Cement Mortar 1:6 and Pointed in Cement Mortar 1:3, (laid Flat in Floor or laid on Side Walls of Brick Drains, Channels), etc., Bricks laid, bedded and pointed in any Cement Mortar, complete all as specified and as directed.

M & L for PCC 1:3:6 type C2 using 40MM graded aggreagte as in surface channel and drains etc complete all as specified and directed

M & L for PCC 1:3:6 type C2 using 40MM graded aggreagte as in mass concrete around hume pipe etc complete all as specified and directed

M&L reinforced cement concrete pipes class NP3 600 mm bore laid in trenches at any depth including jointing with collars and testing, complete all as specified

M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 using 20MM graded aggreagte as in coping bed block etc complete all as specified and directed

M&L for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:4 and to be finished even and smooth with out using extra cement complete all as specified and directed

Removing excavated material n exc. 100m and depositing where directed at a level n exc. 1.5 m above the starting point soft/loose soil complete all as specified and directed.

M&L for brocken stone or boulders of hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

Taking down the existing unserviceable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M & L for sub main wiring with 2 run of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 2.5 sqmm alongwith one run of FRLSH PVC insulated & unsheathed copper conductor of nominal cross sectional area 2.5 sqmm as earth continuity conductor drawn through & including stove enamelled steel conduit of suitable size in concealed connected to DB or Main Board duly fixed copper lugs of suitable size as per site requirement complete all as specified and directed.

M & L for sub main wiring with 4 runs of FRLSH PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6 sqmm alongwith two run of FRLSH PVC insulated & unsheathed copper conductor of nominal cross sectional area 6 sqmm as earth continuity conductor drawn through & including stove enamelled steel conduit of suitable size in concealed connected to DB or Main Board duly fixed copper lugs of suitable size as per site requirement complete all as specified and directed.

S & F in repairs sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with magnetic locking system complete including removal of old unsv sheet metal enclosure all as specified .

S & F RCBO for earth leakage and short circuit protection 415 volts suitable for fixing in MCB TPN DB of capacity 63 amps , 30mA complete all as specified and directed.

S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, B-curve, complete all as specified and directed.

S & F in repairs Energy saving new Next generation, energy saving, environment friendly & robust highbay LED with PDC housing suitable for ceiling (Surface/Suspended) mounting with system efficacy not less than 150 lm/W, 6500K Cool day light , with toughened glass highbay light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 150 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 2.5 Sqmm 3 core ceiling rose to fitting and iron bracket made out of Angle iron bend to required shape to be fitted complete all as directed by Engineer-in-Charge.

Supply and Fixing in replacement New generation in replacement energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 flood light with high power LEDs as light source & exclusively designed polycarbonate cover alongwith electronic driver.of rating 120W LED alongwith clamps nut bolts complete all as specified and directed.

S&F in replacement LEDs aviation light 4 Watt IP65 energy saving new generation environmental friendly long life versatile presure die cast aluminium housing with polycarbonate enclosure with pre wired and necessary mounting arrangements,including provision of new 3 core multistranded copper conductor of size 23/0.193, complete all as specified and as directed.

Taking down the existing unservicable UG cable of size 10-50 Sqmm any type/ description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified and directed Note : Earthwork will be measured and paid seperately.

Supply & laying of LT UG XLPE sheathed PVC insulated, screened PVC bedded, Galvanised Steel Strip of Wire armoured Electric Power Cable heavy duty with stranded Aluminium Conductor 1100 Volt grade, cross-sectional area 50 Sqmm 3.5 Core, laid in trenches/surface of Wall/in GI Pipe along with Pole for connec-tion to OH Lines including Brass Cable Glands Mild Steel Flat Iron Clamps, etc. and Testing, complete all as specified and as directed. NOTE : Earthwork, Sand Cushioning, Bricks, GI Pipe, etc. will be measured and paid under appropriate Items.

Excavation in trenches not exc 1.5 mtr width and not exc 1.5 mtr in depth and getting out in soft / loose soil for laying /taking out of LT UG cable complete all as specified and directed.

Returning, filling in incl spreading, leveling , watering and well ramming in layers not exc 25 cm thick in soils complete all as specified and directed.

Removal of surplus soil to a distance not exc 50 mtr away and depositing where directed as a level not exc 1.5 mtr above the starting point complete all as specified and directed

Supply and laying well burnt Bricks , locally available best quality (sub class "B" bricks) laid in trenches perpandicular to U/G cable for cable protection complete all as specified.

Supply , spread and filling approved sand in cable trenches for cushioning of LT UG cable complete all as specified and directed. NOTE :- Punned thickness only will be measured and paid.

Supply & lay GI tubing light grade in protection of cable at road crossing /hard standing/pole protection fixed with clamps as per site requirement etc of size 40 mm dia bore complete all as specified and directed .

S&F in replacement maintenance free chemical Earthing system complete with 03 Nos of Copper pipe of 100 mm dia with UL 467 approved copper bonded earth rods 17 mm dia 3000mm long electrode dipped fully in earth enhancing chemical compound buried in ground to bore holes 100 mm dia vertically to a depth not less 3.5 mtr deep below ground level with top edge of earth electrode at a depth not less than 500 mm below normal ground level, interconnected each other parallelely in Triangle Shape horizontally,With provision of copper busbar of size 32 mm x 6mm for inter connection with copper earth lead strip 32mm x 6mm for further connected to test point terminal block of size 120mm x 120mm x 25mm made of copper as directed including 60 x3 kg (Minimum) NABL Lab certified back fill earth enhancing compound for filling 3 x bore holes with soil mixed ,so as to achieve earth resistance below 1 Ohms including necessary excavation and earth work and Provn of PCC Chamber in PCC (1.3:6) type C1 (using 20 mm graded stone aggregate) with pit cover of 300 mm x 300 mm made of Cast Iron for each earthing complete all as Specified and directed.

S& F in replacement of earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation on insulators duly brazed for loop earthing etc as required with 20X3 mm copper strip complete all as specified and directed.

S & F Test point terminal block made of gun metal or Phosphorus bronze size 75 x 75 x 25 mm, drilled and screwed including 3 Nos 8 mm dia 25 mm long hex head screw duly fixed of PVC box with glass of suitable size over insulators complete all as specified and as directed.

S&F in replacement GI Pipe of 25 mm Dia, ISI Marked , light grade to cover the copper strip (20 mm x 3mm) Complete all as Specified and directed

S&F in repair air termination, single pointed copper rod, 12 mm dia and 600 mm long, fixed on GI pipes with earthing strips for earth coductivity to ground complete all as specified and directed. (NOTE: GI pipe & earthing strip shall be measured and paid seperately)

S&F Epoxy electrical insulator(heavy duty) for fixing of Copper/Aluminium Strip/GI wire complete all as specified and directed.

S& F in replacement of earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles duly fixed over epoxy electrical insulators or any other indicated situation for loop earthing etc as required with 32 x 6mm copper strip duly brazed complete all as specified and directed.

Supply and Fix Aluminium strip 25 x 3 mm with saddles and fixing screws etc. for roof conductors and down conductors above ground and over roof over porcelein insulators complete all as specified and directed

S&F in replacement GI Pipe of 32 mm Dia, ISI Marked , light grade to cover the earth strip Complete all as Specified and directed

Supply and Fix in replacement Thermoplastic Cable Junction Boxes IP66/67 "weather proof" , for outdoor installation without mounting plate with Transparent Lid of Size 217 X 253 X 115 mm for mounting of Test Point and including Necessary civil works and complete all as specified and directed by Engr-in-Charge. Make Cat No. KG9003 of Hensel or equivalent in sintex

M&L in replacement for earthing complete with copper earth plate electrode of size 600 x 600 x 3.15 mm thick buried directly in ground to a depth not less than 2.25 mtr below the normal ground level with top edge of earth plate not less than 1.50 mtr below the normal ground level and connected to Copper strips 20X3 mm by means of copper nut, bolt & washer and protected by 40mm dia GI pipe light grade and watering pipe of 20mm dia GI pipes light grade and connected to earth test point including necessary excavation, earth work, PCC chamber (1:3:6) type C-1 and 40 mm thick RCC pit cover in RCC (1:2:4) type B-1 using 6 mm dia MS round bars @ 150 mm C/C both ways all as shown in electrical plate No. 5 of SSR Part-I all as specified and directed. NOTES : The unit rate includes for protection pipe and Copper strip from top of earth plate up to 7.00 meter above ground level.

M&L for earthing complete with galvanised steel earth plate electrode size 600x600x6.0mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised earth lead wire 4.0 mm dia means of bolts, nuts, check nuts and washers of galvanised steel and GI pipe light grade 20mm dia bore for watering funnel with wire mesh refilling with vegetable soil without bolders and stones, gravels and aggregate etc,and CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion. NOTES : The unit rate includes for protection pipe and GI wire dia from top of earth plate up to 7.00 meter above ground level.

S & F sheet metal enclosure MCB VTPN 08 way Double door Ready to use DBs - Provided with insulated vertical phase bus-bars |neutral bar/s with shroud/s | earth bar/s | sticking saddles | cement spill protector | color-coded interconnecting wire set | cable ties | blanking plates and circuit identification labels With provision for 4 Pole MCCB 160 A as incomer and SP/SPN MCBs as outgoing complete all as specified and directed.

S & F MCCB 4 Pole 415 volts 100 Amps with thermal - magnetic release with breaking capacity 25 KA and with adjustable overload setting complete all as specified.

Dismantling and taking up unserviceable electric motors of capacity 2HP from foundations of door Hangar after disconnectiong electric connections and transportation from site to work shop for carrying out repairs/ rewinding of motors as required including re-fixing in position and connecting and testing complete as directed.

M & L for opening up short ciruited electric induction motor, 2HP, 3 Phase AC 440 Volts, cutting and removing the burnt stator winding colls complete and re-widing the same with super enamelled copper conductor wires of appropriates size as per the existin gauge including cleaning of slots, all necessary insulating materials, varnishing, dryining complete ressembling motor including repairing to body by welding/ grinding as required complete all as specified and directed.

S/F terminal connector for motors of capacity 2 HP complete all as specified and directed

S/F PVC fan blade for motors of capacity 2 HP complete all as specified and directed

Repairs of squirrel cage induction motor shaft by welding/ griding, polishing to required sizes for motors of the capacity 2 HP complete all as specified and directed

Replacement of ball bearing suitable for capacity 2 HP complete all as specified and directed

M & L for opening and carrying out repair to Gear Mechanism mounted on shaft of 2 HP motor of hangar doors after dismantling the assembly conplete for replacement of worn out spares as Gear Tooth Profile, Gear Shaft, sleeves, bushes etc including filling, turning & polishing works to Gear shaft, as necessiated, reassembling the Gear moving mechanism after repairs and testing complete all as specified and directed

Supply and fix in replacement of Gear tooth system profile with bushes as per existing at site suitable for 2 HP motor complete all as specified and directed

Supply and fix in repair Shaft steel of surface door opener with key and bushes suitable for 2 HP motor complete all as specified and directed

Supply and fix of Bearing & bush of surface door opener with key and bushes suitable for 2 HP motor complete all as specified and directed

S & F Motor coupler sleeve with key of surface door opener of Hangar of capacity 2 HP capacity complete all as specified and directed

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manhole, pier holes etc. n exec 10 Sqm on plan and n exc 1.5 m in depth and getting out in soft/lose soil complete all as specified and directed

M/s ARUNACHAL HARDWARE STORE (BID ID -3483382)

Markson (BID ID -3483091)

SUNIL KUMAR VERMA (BID ID -3482843)