Providing a Security guard cabin with a check post at the Convergence building and Speed breakers on the road in front of the Registrars quarters and besides the new check post

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed: All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation ect. In layers not exceeding 20 cm in depth, consolidation each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 (1 cement: 6 coarse sand) etc complete

12 mm cement plaster of mix: 1:4 (1 cement: 4 fine sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, and one coat of epoxy paint including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Structural steel work in single section, fixe with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and one coat of epoxy paint all complete.

Providing and fixing 4 mm thick ACP paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass/stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-Charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions ect. With EPDM rubber/neoprene gasket ect. Complete as per architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm(+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, IN 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDMseal, complete upto any pitch in horizontal/vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm(+0.05%), total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, IN 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete: Ridges plain (500-600 mm)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 125 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per : 1868), trasparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

Supplying and fixing 300 mm Aluminium aldrop

Providing and fixing modular rubber yellow and black colored speed breakers on road with bitumen emulsion and metal bolts size of 500x400x75mm.

Providing and fixing manually operated rising barrier length of 5m maid by 65 mm GI pipe 14 guage including steel primer with 50mm bracket Barings completed with two coats of enamel painting and reflective sticker on both side.

Fixing PVC split pipe including jointing of pipe with one step PVC solvent cement, testing of joints complete as per direction of Engineer in charge. 200mm 4kgf/sq cm. Including clamps at a distance of 1-meter center or as per directions of engineer in charge.

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer

Providing and applying PVC pipes with one step PVC solvent cement, trenching and refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 4 Kgf/cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Elbow

Painting (one or more coats) with black Japan paint of approved brand and manufacture to give an even shade.